English dropdown-ico

Manual Hobart FP300

8 pages 0.16 mb
Download

Go to site of 8

Summary
  • Hobart FP300 - page 1

    FORM 19157 Rev. B (11-98) FP300 FOOD PROCESSOR MODEL FP300 ML-104495 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 I N S T R U C T I O N S MODEL FP300 FOOD PROCESSOR ...

  • Hobart FP300 - page 2

    – 2 – Installation, Operation, and Care of MODEL FP300 FOOD PROCESSOR SA VE THESE INSTRUCTIONS GENERAL The FP300 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicing vegetables, fruits, or cheese. The compact unit is designed for ease of operation and quick cleaning. A Work Table, a Wall Rack, and a wide range of ...

  • Hobart FP300 - page 3

    – 3 – ELECTRICAL CONNECTION WARNING : THE ELECTRICAL CORD HAS A THREE-PRONGED GROUNDING PLUG WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT REMOVE THE GROUNDING PRONG FROM THE PLUG. ELECTRICAL DATA Model Volts / Hz / Phase Amps FP300 120 / 60 / 1 10 O ...

  • Hobart FP300 - page 4

    – 4 – Operations with a Single Plate — (Fig. 1) SLICING, SHREDDING, GRATING, AND JULIENNE CUTTING 1. Raise the pusher plate using the pistol grip handle and turn it to the left. 2. Release the feed hopper lock by turning the finger paddle counterclockwise. Then raise the feed hopper. 3. Lower the flinger plate on the knife shaft until the fli ...

  • Hobart FP300 - page 5

    – 5 – USING THE FEED HOPPER After the pusher plate is raised, pre-pared products, such as potatoes, carrots, onions, lettuce, cabbage, etc. can be placed in the large feed hopper. When cutting French fries with the Julienne cutter, position the potatoes at the lower-right corner of the large feed hopper. The potatoes may be stacked to cut sever ...

  • Hobart FP300 - page 6

    – 6 – CUTTING TOOLS Fractional sizes are in inches (millimeters are in parentheses). Slicers Use Fine and Standard Slicers for sliced products and for dicing. Soft products like tomato use the FINE SLICER not the STANDARD SLICER. FINE SLICER 1/16 (1.5MM) FINE SLICER 1/8 (3MM) FINE SLICER 5/32 (4MM) FINE SLICER 7/32 (6MM) FINE SLICER 3/8 (10MM) ...

  • Hobart FP300 - page 7

    – 7 – Dicer and French Fry Plates The recommended slicer plate will produce near-cube shaped products. The DICER grid dimension must be equal to or larger than the SLICER dimension. DICER 9/32 Use with FINE SLICER 7/32 * DICER 3/8 Use with STANDARD SLICER 3/8 * DICER 1/2 Use with STANDARD SLICER 3/8 * DICER 5/8 Use with STANDARD SLICER 3/8 * DI ...

  • Hobart FP300 - page 8

    – 8 – FORM 19157 Rev. B (11-98) PRINTED IN U.S.A. MAINTENANCE WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE. Routinely inspect the machine to assure that it is in proper working order. Plates must be clean, intact and sharp. The pusher plate shaft should be regularly lubricated with a drop of mineral ...

Manufacturer Hobart Category Food Processor

Documents that we receive from a manufacturer of a Hobart FP300 can be divided into several groups. They are, among others:
- Hobart technical drawings
- FP300 manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart FP300
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart FP300.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart FP300, service manual, brief instructions and user manuals Hobart FP300. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart FP300.

Similar manuals

A complete manual for the device Hobart FP300, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart FP300 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart FP300.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart FP300 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart FP300, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart FP300, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart FP300 - which should help us in our first steps of using Hobart FP300
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart FP300
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart FP300 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart FP300?

Use the form below

If you did not solve your problem by using a manual Hobart FP300, ask a question using the form below. If a user had a similar problem with Hobart FP300 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)