English dropdown-ico

Manual Telex NEO-10

26 pages 1.27 mb
Download

Go to site of 26

Summary
  • Telex NEO-10 - page 1

    Model NEO-10 Version 1.0 Technical Manual November 26, 2003 PN: 803968 ...

  • Telex NEO-10 - page 2

    2 Table of Contents 1 INTRODUCTION................................................................................................................... ........................... 3 2 CONNECTING NE O TO THE WORLD .................................................................................................... .... 4 2.1 RS-232 P ORT .............. ...

  • Telex NEO-10 - page 3

    3 1 Introduction The NEO-10 device is a network based Input Outpu t device. Within its enclosure are 10 DPDT relays with all 6 contacts of the relays brought out to ports (Normally Open, Norm al ly Close, Common for each half of relay). There are also 10 dio de blocked inp uts which can be used to mo nitor external events. The NEO sends out multica ...

  • Telex NEO-10 - page 4

    4 2 Connecting NEO to the World NEO has a total of three different ports th at are used to connect it to the world. Likely, the first port that will need to be connected is th e RS-232 port. 2.1 RS-232 Port The RS-232 port is used for initial setup purpo ses only. It is a standard DCE pinout allowing a straight through DB9 cable to connect it to a ...

  • Telex NEO-10 - page 5

    5 3 Sof tware Configuration of NEO Setup of the N EO is almost enti rely done using a web browser. The first step required during setup is to assign the IP and Mask a ddresses to the NEO, using either a WEB Browser or Hyper Te rminal program if the assigned IP address is not accessible on your network. 3.1 Setting the basic IP information with Hype ...

  • Telex NEO-10 - page 6

    6 At the main Hyper Term inal screen type up percase S then <enter>. Enter “technobabble” for the factory password. ...

  • Telex NEO-10 - page 7

    7 A = The board serial num ber and case serial number s hould match. B = Do you want to reset the PIN number programmed into NEO. C = Current I P address, do yo u want to change ? D = Current Subn et Mask, do you want to change? E = Current Gateway address , do you want t o change? F = Do you wa nt to reset any of the above ? Once all param eters h ...

  • Telex NEO-10 - page 8

    8 3.2 General Setup via Web Pages The majority of the setup of the NEO is com pleted through t he Ethernet port. Onc e the steps of 3.1 ha ve been completed, a PC on the network can be used to gain access to the web page based setup of the NEO. In the URL window of Int ernet Explore r, type http://X.X.X.X where X.X.X.X is the IP address se t in the ...

  • Telex NEO-10 - page 9

    9 Once all parameters are set, press the Submit bu tton to se nd them back to the NEO fr om the web browser. The parameters are not updated until they are actually saved to EPROM, (Section 3.9) Figure 3 – Basic Ethernet Setup Screen ...

  • Telex NEO-10 - page 10

    10 3.4 Multicast Setup A single m ulticast address is em ployed by NEO for t he purpose of upda ting consoles o f changes in the R elays and Inputs. NEO sends out a single packet each time either a Relay is changed by a ny console or when an input changes due to external event. The Multicas t Address is any address in the range of 224.0.0.0 to 2 39 ...

  • Telex NEO-10 - page 11

    11 3.5 Debounce Input Settings The Debounce hyperlink will open the screen below. Each of the 10 input s can have its own inp ut debounce time. This is t he amount of tim e, in milliseconds, that the input is allowed to stabilize from first change detectio n to final sampling. The timer resolution is only 20ms, so multiples of 20ms must be used. Ot ...

  • Telex NEO-10 - page 12

    12 3.6 Echo Packet The Echo Packet function allo ws the system to operate on networks that do not support multicast. A typical application might be a number of radios spread throu ghout a network. Since multicast is not suppo rted, the radio adaptors (IP-223s or C-6200s) are programmed to send packets to a specific static IP ad dress; the IP addres ...

  • Telex NEO-10 - page 13

    13 Figure 7 - Echo Packet Setup ...

  • Telex NEO-10 - page 14

    14 3.7 Clone From Other NEO The Clone func tion allows for t he parameters of one NEO to be copied t o another ove r the network. Sim ply enter the IP address of the unit to co py the parameters from a nd press the submit button . Th e parameters will be copied. The only parameters that are not c opied are the PIN num ber, IP address, and Mask. F i ...

  • Telex NEO-10 - page 15

    15 3.8 PIN Change The PIN num ber is the passw ord required to enter the set up mode of t he NEO. The default is no PI N number. T he PIN number is a 4 digit num ber that m ust be entered t wice and then s ubmitted. F igure 9 - Set PIN Numb er ...

  • Telex NEO-10 - page 16

    16 3.9 Save Changes to EEPROM As each group of settings are change d an d submitted, they still must be saved to EEPROM to be stored perm anently. Some settings req uire reboot of the device to ta ke effect. These are primarily IP parameters. F igure 10 - Save to EEPROM ...

  • Telex NEO-10 - page 17

    17 4 BILL OF MA TERIAL AND SCHEMA TICS ...

  • Telex NEO-10 - page 18

    REVISIONS RE V DESCRIPTION ECO NO DATE A PPD 1 PROTOTYPE 09/16/03 This drawing, written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX. Telex Communications INC. Lincoln, Nebraska USA APPROVALS: DR BY: SBC DATE: 09/16/2003 PROD ...

  • Telex NEO-10 - page 19

    ITEM NEW QTY TYPE DESCRIPTION PART NO. DESIGNATOR 1 14 CAP 10uf 16vTANT 3528 B 102877065T C1 C3 C11 C18 C19 C68 C71 C73 C74 C123 C124 C131 C162 C329 2 15 CAP 0805 0.1UF 25V +/-10% 102881186T C6 C7 C8 C9 C10 C12 C13 C29 C30 C56 C69 C72 C75 C330 C59 3 1 CAP 1000U,ELECTROLYTIC,LEADED D O NOT PLACE C15 4 1 CAP .001UF 0603 50V +/-10% 102881717T C150 5 2 ...

  • Telex NEO-10 - page 20

    ITEM NEW QTY TYPE DESCRIPTION PART NO. DESIGNATOR This drawin g , written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX. Telex Communications INC. Lincoln, Nebraska USA APPROVALS: DR BY: SBC DATE: 09/16/2003 PROD: CHK: APPD: 8 ...

  • Telex NEO-10 - page 21

    ITEM NEW QTY TYPE DESCRIPTION PART NO. DESIGNATOR This drawin g , written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX. Telex Communications INC. Lincoln, Nebraska USA APPROVALS: DR BY: SBC DATE: 09/16/2003 PROD: CHK: APPD: 8 ...

  • Telex NEO-10 - page 22

    ...

  • Telex NEO-10 - page 23

    ...

  • Telex NEO-10 - page 24

    ...

  • Telex NEO-10 - page 25

    ...

  • Telex NEO-10 - page 26

    18 5 W arranty , Service, Rep air , and Comment s Important! Be sure the exact return address and a description of the problem or work to be done are enclosed w ith your equipment. Warranty (Limited) All Telex Manufactured Veg a signaling pr oducts are guara nteed against m alfunction due to defects in materials and workmanship for three year s, be ...

Manufacturer Telex Category Stereo System

Documents that we receive from a manufacturer of a Telex NEO-10 can be divided into several groups. They are, among others:
- Telex technical drawings
- NEO-10 manuals
- Telex product data sheets
- information booklets
- or energy labels Telex NEO-10
All of them are important, but the most important information from the point of view of use of the device are in the user manual Telex NEO-10.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Telex NEO-10, service manual, brief instructions and user manuals Telex NEO-10. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Telex NEO-10.

Similar manuals

A complete manual for the device Telex NEO-10, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Telex NEO-10 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Telex NEO-10.

A complete Telex manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Telex NEO-10 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Telex NEO-10, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Telex NEO-10, that we can find in the current document
3. Tips how to use the basic functions of the device Telex NEO-10 - which should help us in our first steps of using Telex NEO-10
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Telex NEO-10
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Telex NEO-10 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Telex NEO-10?

Use the form below

If you did not solve your problem by using a manual Telex NEO-10, ask a question using the form below. If a user had a similar problem with Telex NEO-10 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)