-
Kodak Series 3 - page 1
User’s Guide A-6112 1 Part No. 1H7191 Super12 Document Printer ...
-
Kodak Series 3 - page 2
A-61121 May 1999 1 Using the Super12 Document Printer The Kodak Digital Science Super12 Document Printer prints customer- specified information on documents as they pass through the transport system. The Super12 Document Printer can be an accessory on the following: • Kodak Digital Science Document Scanner 9500 • Kodak Digital Science Document ...
-
Kodak Series 3 - page 3
2 A-61121 May 1999 Printed information The information printed by the Super12 Document Printer is defined during installation. The Super12 Document Printer prints up to 12 lines per document. Each line can be a maximum of 12 characters, consisting of as many as three of the following items: • Document image address • Day of the week • Date ? ...
-
Kodak Series 3 - page 4
A-61121 May 1999 3 Changing the print location and print position The location of the information you want printed on a document is determined by the print location of the Super12 Document Printer and the pre-defined print position. Print Location The Super12 Document Printer can be placed in one of six available locations across the transport plat ...
-
Kodak Series 3 - page 5
4 A-61121 May 1999 To remove the plastic strips from a print location: 1. Open the front cover of the scanner. 2. Lift the pri nter from the printer brack et and place i t on the hanger brac ket to keep it out of the way. CA U TION : H ot s urface, av oi d cont act. NOTE: Be sure the flex cable is placed between the two hooks so it does not get dam ...
-
Kodak Series 3 - page 6
A-61121 May 1999 5 5. Rem ove the plasti c str ips from the des ired pr int loc ations from the unders ide of the belt m odule. The pr int locati ons that you rem ove the plas tic st rips from should c orres pond wit h the stri ps you rem oved f r om the tr ansport pl ate. NOTE: Verify that the maintenance tray is in place before continuing. If the ...
-
Kodak Series 3 - page 7
6 A-61121 May 1999 Print Position The print position specifies how far from the leading edge (fed into the transport first) of the document the information will be printed. The default print position is defined at installation. You can temporarily change the default print position by using function code F46. The new print position will be used to p ...
-
Kodak Series 3 - page 8
A-61121 May 1999 7 Enabling/disabling the Super12 Document Printer Make sure the Super12 Document Printer is enabled before feeding documents. • The Super 12 Docum ent Pri nter may be enabled/disabl ed separatel y at the mode l evel usi ng f unc tion code F43. • I f you have enabl ed the Super12 Doc ument Pr inter, but do not want to pri nt on ...
-
Kodak Series 3 - page 9
8 A-61121 May 1999 Function codes The information printed by the Super12 Document Printer is defined during installation. Individual modes are defined for use with specific applications. If a Super12 Document Printer has been installed, some or all modes may allow use of the Super12 Document Printer. In addition, the customer- specified information ...
-
Kodak Series 3 - page 10
A-61121 May 1999 9 F45 — Verifying print quality Perform the following procedure to verify the print quality is satisfactory: 1. Enter function code F45 (P rint Tes t) and pr ess Enter . 2. Press 2 ( Test Patter n). The tr ansport star ts automati cally . 3. Feed a blank s heet of paper; a test patter n will be prin ted . 4. Evaluate t he appeara ...
-
Kodak Series 3 - page 11
10 A-61121 May 1999 F49 — Aligning the print image To align the print image so the left half of the image matches the right half of the image: 1. Enter function code F49 . 2. Press En ter . The curre nt alig nment va lue will be disp layed. 3. Pres s the up ( ↑ ) arr ow to mov e the left half of the im age clos er to the leadi ng edge of the do ...
-
Kodak Series 3 - page 12
A-61121 May 1999 11 F56 — Checking the print cartridge jet connections To determine if all ink jets are functioning properly: 1. Enter function code F56 . 2. Press En ter . The number of jets out per c haracter , as well as the tot al nu mber of je ts ou t, will be disp layed . Pri nt Cartr idge Status 000000000000 0 0 All zeros will be disp laye ...
-
Kodak Series 3 - page 13
12 A-61121 May 1999 Installing a new print cartridge Before you begin, be sure the scanner is powered-on. IMPO RT A NT : Do not remove or insert pri nt cartridge s whi le the printer is in the c apped position. Us e function c ode F40, Op tion 1 - Ch ange H ead(s ) or dam age can be done to the Super12 Doc um ent Printe r. To install a new print ca ...
-
Kodak Series 3 - page 14
A-61121 May 1999 13 4. I f the print cartr idges are al ready i nstall ed, remov e the cartr idges. 5. Open the new pr int car tridge pac kage and remov e the print car tridge from the package. 6. Rem ove the protecti ve tape from the bottom of the pri nt cartr idge. NOTE: Do not discard the protective tape if you plan on storing a partially used p ...
-
Kodak Series 3 - page 15
14 A-61121 May 1999 7. Sli de a new pri nt cartr idge in the Super 12 Docum ent Printer slots, then gently push the car tridge forw ard until you hear and feel i t cli ck into p lace. Use t he illustra tion b elow as a guid e. IMPORTANT: If changing both print cartridges, install the one that is farthest away from the Orientation switch first. 8. W ...
-
Kodak Series 3 - page 16
A-61121 May 1999 15 I f either (or both) pr int cartr idges are not seated correc tly, one (or bo th) of th e yello w lig hts on t he f lex cable will f lash . If th is happens, repeat Steps 7 through 9 until the pri nt cartr idges ar e install ed correctly. NOTE: The flashing lights on the flex cable correspond with the print cartridge(s) that is ...
-
Kodak Series 3 - page 17
16 A-61121 May 1999 Maintenance This section provides: • Recommended cleaning guidelines. • A list of catalog numbers and supplies needed to maintain the Super12 Document Printer. • Cleaning procedures for the Super12 Document Printer. • Instructions for changing the maintenance tray. Cleaning guidelines Use the following information as a g ...
-
Kodak Series 3 - page 18
A-61121 May 1999 17 Cleaning materials and supplies Use the Super12 Maintenance Kit that comes with the Super12 Document Printer. The Maintenance Kit contains the following: • Cleaning swabs • Rubber gaskets • A maintenance tray The following supplies are available through your Kodak sales contact. Supply CAT No. Super12 Maintenance Kit 165 8 ...
-
Kodak Series 3 - page 19
18 A-61121 May 1999 7. Enter function code F40 and press En ter . The f ollowin g message will be displa yed: Print Head Po sit ion 1=Ch ange Head( s) 2=Clean Pr inter 8. Selec t 2 ;a Please W ait messa ge will be displa yed. W he n this mes sage is no l onger dis played, open the front c over of the scanner . 9. Lift the pri nter out of the pri nt ...
-
Kodak Series 3 - page 20
A-61121 May 1999 19 To replace the print cartridges: 15. Enter function code F40 and press En ter . The f ollowin g message will be displa yed: Print Head Po sit ion 1=Ch ange Head( s) 2=Clean Pr inter 16. Selec t 1 ;a Please W ait messa ge will be displa yed. W he n this mes sage is no l onger dis played, open the front c over of the scanner . 17. ...
-
Kodak Series 3 - page 21
20 A-61121 May 1999 Cleaning the transport area To thoroughly clean the transport area, perform the following procedure: 1. Open the front cover . 2. Note the cur rent l ocation of the Super12 Doc ument Pri nter, then l ift it from the printer brack et, being car ef ul not to strai n the f l ex cable. 3. Plac e the Super12 Doc ument Pr inter on the ...
-
Kodak Series 3 - page 22
A-61121 May 1999 21 Replacing the maintenance tray Periodically the Super12 Document Printer maintenance tray may need to be replaced. To access and replace the maintenance tray: 1. Open the front cover of the scanner. 2. Plac e the printer on the hanger br acket s o it is out of the way . CA U TION : H ot s urface, av oi d cont act. NOTE: Be sure ...
-
Kodak Series 3 - page 23
22 A-61121 May 1999 5. Lift out the used m aintenance tr ay and dis pose of it accor ding to your local and state regul ations. 6. Open the package c ontaining the new maintenance tr ay and remo ve it. 7. I nsert the new maintenanc e tray; be sure i t is fir mly in plac e. The ali gnment bloc ks on the bottom of the mai ntenance tray should be plac ...
-
Kodak Series 3 - page 24
A-61121 May 1999 23 Storage and handling of print cartridges If unused print cartridges are going to be stored for a period of time, replace the protective tape on the orifice plate of the print cartridge. NOTE: Dispose empty print cartridges according to your local and state regulations. Protective tape Orifice plate ...
-
Kodak Series 3 - page 25
24 A-61121 May 1999 Troubleshooting This section lists possible problems you may encounter when using the Kodak Digital Science Super12 Document Printer. Problem Solution Printing a partial image or printing backwards Be sure the Super12 Document Printer is seated correctly on the printer bracket. Experiencing print problems at startup due to heads ...
-
Kodak Series 3 - page 26
A-61121 May 1999 25 How print position is effected by patch reading The ability to print at the designated print position will be effected by patch reading, and by the amount of printed information which changes for each document. If you encounter print position drift, it may be necessary to change your print template using the Mode Setup Software ...
-
Kodak Series 3 - page 27
26 A-61121 May 1999 If the print position is set at less than 1 inch, the patch window will close at 2.5 inches after the lead edge; the printer can change up to 1 full print line and be able to print at the designated position. However, if more than 1 full print line needs to be changed, the image may drift down the page depending on how much more ...
-
Kodak Series 3 - page 28
A-61121 May 1999 27 Error codes Following is a list of errors codes you may encounter when using the Super12 Document Printer. Error: E133 Feeder waiting for printer. Probable cause: The feeder will not be ready until the printer has moved to the print position. Solution: Wait until the printer has moved into the print position. Error: E206 Check P ...
-
Kodak Series 3 - page 29
28 A-61121 May 1999 If E206 continues to be displayed or the flex cable lights continue to flash, enter F45 to do a Print Test. If the print quality is acceptable, ignore the E206 error or the flashing flex cable lights. If the print quality is not acceptable, try changing one or both of the print cartridges, then enter F45 again to do another Prin ...
-
Kodak Series 3 - page 30
EASTMAN KOD AK COMPANY Doc ument I m aging Roc hester, N ew York 14650 Kodak, Im age li nk, Digit al S ci e nce and the ds m onogram sym bol are tradem arks of Eastm an Kodak Company. Print e d on recycle d paper. A-61121 Part No. 1H7191 3/99 © Eastm an Kodak Com pany, 1999 Prin te d in U.S.A . DOCUMENT IMA GING ...
Do you have a question concerning Kodak Series 3?
Use the form below
If you did not solve your problem by using a manual Kodak Series 3, ask a question using the form below. If a user had a similar problem with Kodak Series 3 it is likely that he will want to share the way to solve it.