English dropdown-ico

Manual Xantech HD44C

16 pages 1.94 mb
Download

Go to site of 16

Summary
  • Xantech HD44C - page 1

    08905071B - 1 - INSTALLATION INSTRUCTIONS HD44CC5 HD44C High Definition Video Matrix Switcher, Coaxial and CAT5 High Definition Video Matrix Switcher, Coaxial Only DESCRIPTION The HD44CC5 four-source, four-z one high-definition matrix swit cher has component video and S/PDIF digital audio inputs for each source. A ll four zone outputs have componen ...

  • Xantech HD44C - page 2

    08905071B - 2 - DETAIL OVERVIEW [1] SOURCE LOOP-THROUGH CONNECTION The source inputs are buffered to provide an output at the sa me levels, assuming a 75-ohm termination is on the output. Use these connections for HD44 expansion systems. The buffers are an active circuit. The HD44 must be power ed on for an active connection. [2] SOURCE INPUTS Gold ...

  • Xantech HD44C - page 3

    08905071B - 3 - [3] IR RECEIVER The rear panel IR receiver is a 3.5mm Stereo jack t hat is compatible with all Xantech IR receivers, such as the 291-10. Switch 4 must be in the OFF position to use this jack. PLUG CIRCUIT TIP IR SIGNAL RING GROUND SLEEVE +12VDC, 25mA [4] IR BUS, EMITTER PORT The 3.5mm Mono jack is an emitter port. The IR signal is c ...

  • Xantech HD44C - page 4

    08905071B - 4 - RS232 COMMAND STRUCTURE Where: {CR # } – Carriage Return (0x0D) { z# } - Zone Number. Range is 1..4 (1..16 if expanded) { s# } - Source Input Number. Range is 1..4 { 0/1 } – Either 0 (zero) or 1 (one). 0 – Off, 1 – On. NAME COMMAND RETURN REMARKS !{ z# } PR 01+ To turn on Zone 2: !2PR1+ or !02PR1 + or !2PR01+ or !02PR01+ Zon ...

  • Xantech HD44C - page 5

    08905071B - 5 - RS232 QUERIES Where: {CR # } – Carriage Return (0x0D) { z# } - Zone Number. Range is 1..4 (1..16 if expanded) { s# } - Source Input Number. Range is 1..4 { 0/1 } – Either 0 (zero) or 1 (one). 0 – Off, 1 – On. NAME QUERY RETURN EXAMPLE RETURN EXPLANATION Zone Power ?{ z# } PR + ?{ z# } PR { 0/1 }+ ?4 PR 0+{CR} Power in zone 4 ...

  • Xantech HD44C - page 6

    08905071B - 6 - [6] AC POWER INPUT Standard IEC 3-Conductor AC Line Cord Receptacle fo r plug-in of a 3-conducator power line cord. Be sure to note if the power receptacle is domesti c (120VAC type) or in ternational (240VAC type). [7] RS232 EXPANSION The HD44C and HD44CC5 can be expanded into a lar ger system. By using any combination of the HD44C ...

  • Xantech HD44C - page 7

    08905071B - 7 - [9] CAT5 ZONE OUTPUT Output connection to the HDRXSG01 receiver module. Uses standard CAT5 cable. Be sure to verify CAT5 wiring connection is correct before installation. [10] COAXIAL ZONE OUTPUT Gold-plated RCA jacks for connection to an HD moni tor. Color coordinated to match all HD type products. The CAT5 and coaxial output can b ...

  • Xantech HD44C - page 8

    08905071B - 8 - QUICK INSTALLATION: HD44CC5 and HDRXSG01 [1] Connect the High-Definition Source to the HD44CC5 or HDTXSG01. Figure 1 below shows a HD44CC5 (video matrix transmitter) c onnected to the HDRXSG01 (receiver). [2] Using CAT5 cable, connect the HD44CC5 zone output or the output from the HDTXSG01 to the HDRXSG01. Connect power to the HD44C ...

  • Xantech HD44C - page 9

    08905071B - 9 - RC68+ (IR) COMMANDS The RC68+ should be set to Group Code “C0”. ZONE 1 ZONE 2 ZONE 3 ZONE 4 1 Zone Power Toggle 80 48 10 90 SRC 1 SRC 2 SRC 3 SRC 4 Zone 1 Source Select 00 C0 50 D0 Zone 2 Source Select 40 A0 30 B0 Zone 3 Source Select 20 E0 70 F0 2 Zone 4 Source Select 60 88 18 98 ZONE 1 ZONE 2 ZONE 3 ZONE 4 3 Zone Power On 08 A ...

  • Xantech HD44C - page 10

    08905071B - 10 - ADVANCE INSTALLATION FIGURE 2: Below shows a diagram for a sports bar applic ation. With the equipment rack located near or behind the bar area, the coaxia l outputs can be used for local HD monitors. The CAT5 outputs can be used to deliver HD content to areas such as outdoor patios and pool table recreational areas. FIGURE 2 FIGUR ...

  • Xantech HD44C - page 11

    08905071B - 11 - FIGURE 3 (Note: The top unit (master unit) must be addressed as UNIT #1) ...

  • Xantech HD44C - page 12

    08905071B - 12 - COMMON PROBLEMS AND TROUBLESHOOTING Poor video quality (picture is washed out): Several manufacturers of cable and satellite box may have higher than normal DC offset on the video signals. When connected to an HD44C, HD44CC5, and HDTXSG01, this may result in a washed out picture. To remedy this problem, a DC blocker should be used ...

  • Xantech HD44C - page 13

    08905071B - 13 - This page intentionally left blank ...

  • Xantech HD44C - page 14

    08905071B - 13 - This page intentionally left blank ...

  • Xantech HD44C - page 15

    08905071B - 13 - This page intentionally left blank ...

  • Xantech HD44C - page 16

    X a n te c h L i mit e d Warr a n t y ( E f f e c t i v e f o r p r o d u c t s s o l d a f t e r J ul y 1 , 2006 ) X an t e c h C o r p o r a t i on (“ X an t e c h ”) w a r r an t s t o t h e h o l d e r o f a v a li d p r o o f o f pu r c h a s e a s t h e f i r s t end - u s e r pu r ch a s e r (“ Y ou ”), i t s p r o d u c t s t o b e ...

Manufacturer Xantech Category Switch

Documents that we receive from a manufacturer of a Xantech HD44C can be divided into several groups. They are, among others:
- Xantech technical drawings
- HD44C manuals
- Xantech product data sheets
- information booklets
- or energy labels Xantech HD44C
All of them are important, but the most important information from the point of view of use of the device are in the user manual Xantech HD44C.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Xantech HD44C, service manual, brief instructions and user manuals Xantech HD44C. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Xantech HD44C.

Similar manuals

A complete manual for the device Xantech HD44C, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Xantech HD44C by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Xantech HD44C.

A complete Xantech manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Xantech HD44C - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Xantech HD44C, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Xantech HD44C, that we can find in the current document
3. Tips how to use the basic functions of the device Xantech HD44C - which should help us in our first steps of using Xantech HD44C
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Xantech HD44C
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Xantech HD44C in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Xantech HD44C?

Use the form below

If you did not solve your problem by using a manual Xantech HD44C, ask a question using the form below. If a user had a similar problem with Xantech HD44C it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)