English dropdown-ico

Manual Toshiba RAV-SM1603DT-A

157 pages 5.56 mb
Download

Go to site of 157

Summary
  • Toshiba RAV-SM1603DT-A - page 1

    R410A PRINTED IN JAP AN, Jun, 2008 T oMo FILE NO. A07-009 SER VICE MANUAL AIR-CONDITIONER SPLIT TYPE OUTDOOR UNIT <DIGIT AL INVER TER> RA V -SM1603A T -E RA V -SM1603A TZ-E RA V -SM1603A TZG-E INDOOR UNIT <DIGIT AL INVER TER> RA V -SM1403DT -A RA V -SM1603DT -A ∗ Ref er to the Ser vice Manual with File No . A06-010 f or Model RA V -SM ...

  • Toshiba RAV-SM1603DT-A - page 2

    – 2 – Adoption of New Refrigerant This Air Conditioner is a new type which adopts a ne w refr igerant HFC (R410A) instead of the con v entional refrigerant R22 in order to pre vent destruction of the ozone la yer . W ARNING Cleaning of the air filter and other par ts of the air filter inv olves dangerous work in high places, so be sure to ha ve ...

  • Toshiba RAV-SM1603DT-A - page 3

    – 3 – 6. REFRIGERANT R410A ............................................................................ 35 6-1. Safety During Installation/Servicing ............................................................... 35 6-2. Refrigerant Piping Installation ....................................................................... 35 6-3. T ools ...... ...

  • Toshiba RAV-SM1603DT-A - page 4

    – 4 – SAFETY CA UTION The impor tant contents concer ned to the saf ety are described on the product itself and on this Ser vice Manual. Please read this Ser vice Manual after understanding the descr ibed items thoroughly in the follo wing contents (Indications/Illustrated marks), and keep them. [Explanation of indications] ∗ Proper ty damage ...

  • Toshiba RAV-SM1603DT-A - page 5

    – 5 – Check earth wires. Prohibition of modification. Use specified par ts. Do not bring a child close to the equipment. Insulating measures No fire Refrigerant Assembly/Cab ling Before tr oubleshooting or repair w ork, check the earth wire is connected to the earth terminals of the main unit, otherwise an electric shock is caused when a leak o ...

  • Toshiba RAV-SM1603DT-A - page 6

    – 6 – After the work has finished, be sure to use an insulation tester set (500V Megger) to chec k the resistance is 2M Ω Ω Ω Ω Ω or more between the charge section and the non-c harge metal section (Earth position). If the resistance v alue is low , a disaster such as a leak or electric shock is caused at user ’ s side. When the re ...

  • Toshiba RAV-SM1603DT-A - page 7

    – 7 – • Ne w Refrigerant (R410A) This air conditioner adopts a new HFC type refrigerant (R410A) which does not deplete the oz one la yer . 1 . Safety Caution Concerned to New Refrigerant The pressure of R410A is high 1.6 times of that of the f or mer refrigerant (R22). Accompanied with change of refrigerant, the refrigerating oil has been als ...

  • Toshiba RAV-SM1603DT-A - page 8

    – 8 – 4 . T ools 1. Required T ools f or R410A Mixing of diff erent types of oil ma y cause a trouble such as generation of sludge , clogging of capillar y , etc. Accordingly , the tools to be used are classified into the follo wing three types. 1) T ools exclusiv e for R410A (Those which cannot be used f or conv entional refrigerant (R22)) 2) ...

  • Toshiba RAV-SM1603DT-A - page 9

    – 9 – 1. SPECIFICA TIONS 1-1. Indoor Unit 1-1-1. High Static Duct T ype <Single type> ∗ : IEC standard, ∗∗ : AS standard Model Indoor unit RA V - Outdoor unit RA V - Cooling capacity (kW) Heating capacity (kW) P ower supply Running current (A) P ower consumption (kW) Cooling P ower f actor (%) EER Energy efficiency class ∗ Electri ...

  • Toshiba RAV-SM1603DT-A - page 10

    – 10 – 1-1-2. 4-way Air Dischar ge Cassette T ype <Single type> Model Indoor unit RA V - Outdoor unit RA V - Cooling capacity (kW) Heating capacity (kW) P ower supply Running current (A) P ower consumption (kW) Cooling P ower f actor (%) EER Energy efficiency class ∗ Electrical Energy rating ∗∗ Running current (A) characteristics P ...

  • Toshiba RAV-SM1603DT-A - page 11

    – 11 – <T win type> Indoor unit 1 RA V - SM804UT - E Model Indoor unit 2 RA V - SM804UT - E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running current (A) 21.48 – 19.69 P ower consumption (kW) 4.49 Cooling P ower f actor (%) 95 E ...

  • Toshiba RAV-SM1603DT-A - page 12

    – 12 – <T riple type> Indoor unit 1 RA V - SM564UT - E Model Indoor unit 2 RA V - SM564UT - E Indoor unit 3 RA V - SM564UT - E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running current (A) 21.48 – 19.69 P ower consumption (kW) 4 ...

  • Toshiba RAV-SM1603DT-A - page 13

    – 13 – 1-1-3. Concealed Duct T ype <T win type> Indoor unit 1 RA V - SM802BT - E Model Indoor unit 2 RA V - SM802BT - E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running current (A) 24.50 – 22.46 P ower consumption (kW) 5.12 Coo ...

  • Toshiba RAV-SM1603DT-A - page 14

    – 14 – <T riple type> Indoor unit 1 RA V - SM562BT - E Model Indoor unit 2 RA V - SM562BT - E Indoor unit 3 RA V - SM562BT - E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running current (A) 24.50 – 22.46 P ower consumption (kW) 5 ...

  • Toshiba RAV-SM1603DT-A - page 15

    – 15 – 1-1-4. Under Ceiling T ype <T win type> Indoor unit 1 RA V - SM802CT - E Model Indoor unit 2 RA V - SM802CT - E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running current (A) 23.88 – 21.89 P ower consumption (kW) 4.99 Cool ...

  • Toshiba RAV-SM1603DT-A - page 16

    – 16 – <T riple type> Indoor unit 1 RA V - SM562CT - E Model Indoor unit 2 RA V - SM562CT - E Indoor unit 3 RA V - SM562CT - E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running current (A) 23.88 – 21.89 P ower consumption (kW) 4 ...

  • Toshiba RAV-SM1603DT-A - page 17

    – 17 – 1-1-5. High Wall T ype <T win type> Indoor unit 1 RA V - SM802KRT -E Model Indoor unit 2 RA V - SM802KRT -E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running current (A) 24.40 – 22.37 P ower consumption (kW) 5.10 Cooling ...

  • Toshiba RAV-SM1603DT-A - page 18

    – 18 – <T riple type> Indoor unit 1 RA V - SM562KRT -E Model Indoor unit 2 RA V - SM562KRT -E Indoor unit 3 RA V - SM562KRT -E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running current (A) 24.40 – 22.37 P ower consumption (kW) 5 ...

  • Toshiba RAV-SM1603DT-A - page 19

    – 19 – 1-1-6. Compact 4-way Cassette (600 × 600) T ype <T riple type> Indoor unit 1 RA V - SM562MUT -E Model Indoor unit 2 RA V - SM562MUT -E Indoor unit 3 RA V - SM562MUT -E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running curr ...

  • Toshiba RAV-SM1603DT-A - page 20

    – 20 – 1-1-7. Slim Duct T ype <T riple type> Indoor unit 1 RA V - SM564SDT -E Model Indoor unit 2 RA V - SM564SDT -E Indoor unit 3 RA V - SM564SDT -E Outdoor unit RA V - SM1603A T(Z)(ZG)-E Cooling capacity (kW) 14.0 Heating capacity (kW) 16.0 Indoor unit P ower supply 1 phase 230V (220 – 240V) 50Hz Running current (A) 23.88 – 21.89 P ...

  • Toshiba RAV-SM1603DT-A - page 21

    – 21 – 1-2. Outdoor Unit Model name P ower supply T ype Compressor Motor (kW) P ole Refrigerant charged (kg) Refrigerant control Standard length (m) Min. length (m) Inter Max. total length (m) Additional refrigerant charge connecting pipe under long piping connector Height Outdoor low er (m) diff erence Outdoor higher (m) Height (mm) Outer dime ...

  • Toshiba RAV-SM1603DT-A - page 22

    – 22 – 1-3. Operation Characteristic Curve • Operation characteristic curve RA V -SM1603A T -E, RA V -SM1603A TZ-E, RA V -SM1603A TZG-E <Cooling> <Heating> 0 2 04 06 0 Compressor speed (rps) 79 100 120 Current (A) 0 2 04 06 0 Compressor speed (rps) 78.6 100 120 0 2 4 6 8 10 12 14 16 18 20 22 23.7 25 20 28.2 22 24 26 18 16 14 12 10 ...

  • Toshiba RAV-SM1603DT-A - page 23

    – 23 – 2. CONSTRUCTION VIEWS (EXTERNAL VIEWS) 2-1. Indoor Unit RA V -SM1403DT -A, RA V -SM1603DT -A 20 10 296 316 15 25 10 25 25 20 60 276 (Inside) 274 (Inside) 757 (Inside) 845 (Inside) 25 25 20 20 12 65 65 12 25 67.5 250 250 885 11 × 65 = 715 250 67.5 15 256 256 271 807 11 × 65 = 715 4 × 60 = 240 300 324 15 25 60 4 × 60 = 240 10-Ø5 hole ...

  • Toshiba RAV-SM1603DT-A - page 24

    – 24 – 2-2. Outdoor Unit RA V -SM1603A T -E, RA V -SM1603A TZ-E, RA V -SM1603A TZG-E 365 17.5 74 17.5 128 46 48 655 121 534 534 85 65 7 55 95 55 94 95 55 95 24 1340 155 605 613 70 74 581 581 360 40 40 54 34 170 118 380 383 150 600 900 550 60 83 7 68 518 135 151 12 Unit : mm 64 Z 178 Knock out for do wnward piping Z views 327 400 178 178 80 18 8 ...

  • Toshiba RAV-SM1603DT-A - page 25

    – 25 – RBC-TWP30E2, RBC-TWP50E2 (Simultaneous T win) Inner diameter Ø C Inner diameter Ø D Inner diameter Ø D A B Model (RBC-) TWP30E2 Liquid side Gas side TWP50E2 Liquid side Gas side ABCD 36 14 Ø 9.5 Ø6.4 43 23 Ø 15.9 Ø12.7 34 14 Ø 9.5 Ø9.5 44 21 Ø 15.9 Ø15.9 ...

  • Toshiba RAV-SM1603DT-A - page 26

    – 26 – RBC-TRP100E (Simultaneous T riple) <Gas side> Header assemb ly Ø15.9 (External diameter) Ø25.4 (External diameter) Ø9.5 (External diameter) Ø12.7 (External diameter) Inner diameter Ø25.4 Inner diameter Ø12.7 Inner diameter Ø15.9 Inner diameter Ø9.52 Insulator 300 80 80 100 80 80 100 Ø12.7 Ø15.9 Ø6.4 Ø9.5 100 28 10 46 12 ...

  • Toshiba RAV-SM1603DT-A - page 27

    – 27 – 3. SYSTEMA TIC REFRIGERA TING CYCLE DIA GRAM 3-1. Indoor Unit <Indoor unit to be connected to RA V -SM1403DT -A, RA V -SM1603DT -A> • Single type (Combination of one indoor unit and one outdoor unit) Indoor unit SM140, 160 type Outer diameter of refrigerant pipe Gas side ØA Liquid side ØB 15.9 9.5 Model RA V -SM ∗∗∗ DT SM ...

  • Toshiba RAV-SM1603DT-A - page 28

    – 28 – Indoor unit TCJ sensor Air heat e xchanger TC sensor Distributor (Strainer incor porated) Refrigerant pipe at liquid side Outer diameter Ø9.5 Refrigerant pipe at gas side Outer diameter Ø15.9 T o outdoor unit T o outdoor unit Heating Cooling Heating Cooling Heating Cooling Distributor (Strainer incorporated) Distributor (Strainer incor ...

  • Toshiba RAV-SM1603DT-A - page 29

    – 29 – 3-2. Outdoor Unit RA V -SM1603A T -E, RA V -SM1603A TZ-E, RA V -SM1603A TZG-E Systematic Diagram of Refrigerating Cyc le * This compressor has 4-pole motor . The v alue when compressor frequency (Hz) is measured by a clamp meter becomes 2 times of No . of compressor re v olutions (r ps). In cooling operation In heating operation Ø25 × ...

  • Toshiba RAV-SM1603DT-A - page 30

    – 30 – 4. WIRING DIA GRAM 4-1. Indoor Unit RA V -SM1403DT -A, RA V -SM1603DT -A 1. indicates the terminal board and the number indicates the terminal number . 2. The dashed line indicates wiring at the local site. 3. indicates P .C. board. 4. When install Drain Pump. please connect Float Switch Connector to Connector CN030. 5. When changing ext ...

  • Toshiba RAV-SM1603DT-A - page 31

    – 31 – • Single type Notes) 1. : indicates a ter minal bloc k 2. Brok en line and chain line indicate wiring at local site. 3. F or the inner wir ing diagram of the outdoor unit and the indoor unit, ref er to the wiring diagram of each model. 4. There is no polarity . It is no problem that the remote controller is connected to the indoor unit ...

  • Toshiba RAV-SM1603DT-A - page 32

    – 32 – 4-2. Outdoor Unit RA V -SM1603A T -E, RA V -SM1603A TZ-E, RA V -SM1603A TZG-E Fuse, 50A, 250V~ WHI RED RED PNK ORN BLU WHI BLK RED WHI RED P ower supply 220 – 240V~, 50Hz WHI BLK BLU YEL WHI RED WHI Reactor CN01 CN08 WHI CN06 WHI CN22 BLU CN05 WHI CN04 WHI CN702 WHI Serial communication circuit F an motor drive circuit CN700 YEL R Y700 ...

  • Toshiba RAV-SM1603DT-A - page 33

    – 33 – 4-3. Fan Characteristics Current value as a criterion, adjust the air volume v alue to become within the range of the char t below . REQUIREMENT Install the v olume damper in the air outlet, and adjust the airflow t o become within the range of the char t abov e. n Wire connection change of fan motor Wiring connection of the fan motor is ...

  • Toshiba RAV-SM1603DT-A - page 34

    – 34 – 5. SPECIFICA TIONS OF ELECTRICAL P AR TS 5-1. Indoor Unit RA V -SM1403DT -A, RA V -SM1603DT -A No. 1 2 3 4 P ar ts name F an motor T A sensor TC sensor TCJ sensor T ype SWF-240-600-4A Lead wire length : 1200mm Ø6 size lead wire length : 1200mm Vinyl tube (Black) Ø6 size lead wire length : 1200mm Vinyl tube (Red) Specifications Output ( ...

  • Toshiba RAV-SM1603DT-A - page 35

    – 35 – 6. REFRIGERANT R410A This air conditioner adopts the new refrigerant HFC (R410A) which does not damage the ozone la yer . The working pressure of the new refrigerant R410A is 1.6 times higher than conv entional refr igerant (R22). The refr igerating oil is also changed in accordance with change of refrigerant, so be careful that water , ...

  • Toshiba RAV-SM1603DT-A - page 36

    – 36 – T able 6-2-1 Thicknesses of annealed copper pipes 1. Joints F or copper pipes, flare joints or soc ket joints are used. Pr ior to use, be sure to remov e all contaminants. a) Flare Joints Flare joints used to connect the copper pipes cannot be used f or pipings whose outer diameter e xceeds 20 mm. In such a case, sock et joints can be us ...

  • Toshiba RAV-SM1603DT-A - page 37

    – 37 – c) Inser tion of Flare Nut d) Flare Processing Make certain that a clamp bar and copper pipe hav e been cleaned. By means of the clamp bar , perform the flare processing correctly . Use either a flare tool f or R410A or conv entional flare tool. Flare processing dimensions diff er according to the type of flare tool. When using a conv en ...

  • Toshiba RAV-SM1603DT-A - page 38

    – 38 – 43˚to 45˚ 45˚to 46˚ B A C D Fig. 6-2-2 Relations between flare nut and flare seal surface 2. Flare Connecting Procedures and Precautions a) Make sure that the flare and union por tions do not hav e any scar or dust, etc. b) Correctly align the processed flare surf ace with the union axis. c) Tighten the flare with designated torque b ...

  • Toshiba RAV-SM1603DT-A - page 39

    – 39 – 6-3. T ools 6-3-1. Required T ools Ref er to the “ 4. T ools ” (P age 8) 6-4. Rechar ging of Refrigerant When it is necessar y to recharge refrigerant, charge the specified amount of new refrigerant according to the f ollowing steps . (INDOOR unit) (Liquid side) Refrigerant cylinder (With siphon pipe) Check v alve (Gas side) Open/Clo ...

  • Toshiba RAV-SM1603DT-A - page 40

    – 40 – Gauge manifold [ Cylinder with siphon ] [ Cylinder without siphon ] OUTDOOR unit Gauge manifold OUTDOOR unit Refrigerant cylinder Electronic balance Refrigerant cylinder Electronic balance Siphon 1) Be sure to make setting so that liquid can be charged. 2) When using a cylinder equipped with a siphon, liquid can be charged without tur ni ...

  • Toshiba RAV-SM1603DT-A - page 41

    – 41 – Nitrogen gas cylinder Pipe Flow meter M Stop valv e F rom Nitrogen cylinder Nitrogen gas Rubber plug 2. Characteristics required for flux • Activ ated temperature of flux coincides with the brazing temperature . • Due to a wide eff ectiv e temperature range , flux is hard to carbonize . • It is easy to remov e slag after brazing. ? ...

  • Toshiba RAV-SM1603DT-A - page 42

    – 42 – 6-6. Instructions f or Re-use Piping of R22 or R407C Instruction of W orks: The existing R22 and R407C piping can be reused for our digital in ver ter R410A products installations. NO TE) Confir mation of existence of scratch or dent of the f or mer pipes to be applied and also confir mation of reliability of the pipe strength are conv e ...

  • Toshiba RAV-SM1603DT-A - page 43

    – 43 – 6-6-5. Final Installation Checks Do not apply the refrigerator oil to the flare surface . Existing pipe: NO * Use a new pipes. Clean the pipes or use the new pipes . T r ial run Is it possible to oper ate the existing air conditioner? W as not largely discolored oil or a large quantity of remains discharged? (When the oil deteriorates, t ...

  • Toshiba RAV-SM1603DT-A - page 44

    – 44 – 6-6-6. Handling of Existing Pipe When using the e xisting pipe, carefully chec k it for the f ollowing: • W all thickness (within the specified range) • Scratches and dents • W ater , oil, dir t, or dust in the pipe • Flare looseness and leakage from welds • Deterioration of copper pipe and heat insulator Cautions f or using ex ...

  • Toshiba RAV-SM1603DT-A - page 45

    – 45 – 1234 ON 1234 ON P .C. boar d Refrigerant recovery switch SW801 Optional connector CN610 Special operation select switch SW804 Existing pipe switch SW802 6-6-7. Recovery Method of Refrig erant RA V -SM1603A T(Z)(ZG)-E • Use the refrigerant recov er y switch SW802 on the P .C . board of the outdoor unit to recov er refriger- ant when the ...

  • Toshiba RAV-SM1603DT-A - page 46

    – 46 – 6-7. T olerance of Pipe Length and Pipe Head n T win system CA UTION When planning a la yout f or Units A and B, comply with the f ollowing: 1. The lengths after branching ( “a” and “b” ) should be equal if f easible . Install Units A and B so that the diff erence of the branching lengths becomes less than 10m if the lengths cann ...

  • Toshiba RAV-SM1603DT-A - page 47

    – 47 – n T riple system CA UTION When planning a la yout f or Units A, B and C, comply with the f ollowing: 1. The lengths after branching ( “a” and “b” , “b” and “c” , “a” and “c” ) should be equal if f easible . Install Units A, B and C so that the diff erence of the branching lengths becomes less than 10m if the lengt ...

  • Toshiba RAV-SM1603DT-A - page 48

    – 48 – 6-8. Additional Refrigerant Amount n T win system <Formula f or Calculating Additional Refrigerant Amount> Do not remov e the refr igerant e ven if the additional refrigerant amount becomes minus result as a result of calculations b y the f ollowing f or mula and operate the air conditioner as it is. Additional refrigerant amount ( ...

  • Toshiba RAV-SM1603DT-A - page 49

    – 49 – n T riple system <Formula f or Calculating Additional Refrigerant Amount> Do not remov e the refr igerant e ven if the additional refrigerant amount becomes minus result as a result of calculations b y the f ollowing f or mula and operate the air conditioner as it is. Additional refrigerant amount (kg) = Main piping additional refr ...

  • Toshiba RAV-SM1603DT-A - page 50

    – 50 – 6-9. Piping Materials and Sizes n T win system Use copper tube of Copper and copper allo y seamless pipes and tubes , with 40mg/10m or less in the amount of oil stuc k on inner w alls of pipe and 0.8mm in pipe w all thic kness for diameters f or diameters 6.4, 9.5 and12.7mm and 1.0mm, f or diameter 15.9mm. Nev er use pipes of thin wall t ...

  • Toshiba RAV-SM1603DT-A - page 51

    – 51 – 6-10. Branch Pipe n T win system Now the refrigerant pipe is installed using br anch pipes supplied as accessories. • Bend and adjust the refrigerant piping so that the branch pipes and pipe after branching become horizontal. • Fix the branch pipes onto a wall in a ceiling or onto a column. • Provide a straight pipe longer than 500 ...

  • Toshiba RAV-SM1603DT-A - page 52

    – 52 – 7. INDOOR CONTR OL CIRCUIT 7-1. Indoor Contr oller Block Dia gram RA V -SM1403DT -A, RA V -SM1603DT -A 7-1-1. Connection of Main (Sub) Remote Controller Max. 8 units are connectable. ∗ 1 ∗ 1 How e ver when mounting a netw or k adapter while 2 main (sub) remote controllers are connected, Max. 7 units are connectable . ∗ 2 A network ...

  • Toshiba RAV-SM1603DT-A - page 53

    – 53 – 7-2. Control Specifications Cooling thermo. OFF (F an) • Setup air volume Cooling operation Heating operation Ta (˚C) -1.0 Ts + α +1.0 No. 1 2 Item When power supply is reset Operation mode selection Outline of specifications 1) Distinction of outdoor unit When the pow er supply is reset, the outdoors are distinguished and the contro ...

  • Toshiba RAV-SM1603DT-A - page 54

    – 54 – Ta ( ˚ C) -1.5 Tsc Tsh +1.5 Heating (Cooling OFF) (Cooling ON) or Cooling No. 3 4 5 Item Room temp . control A utomatic capacity control (GA control) A utomatic cooling/ heating control Outline of specifications 1) Adjustment range: Remote controller setup temperature ( ° C) Setting at shipment Setup data 2 Setup data Setup temp . corr ...

  • Toshiba RAV-SM1603DT-A - page 55

    – 55 – Ta ( ˚ C) +1.0 +0.5 Tsc – 0.5 +1.5 Normal cooling Cooling in Cooling/Heating [A UTO] HH (High wind) HH (High wind) HH (High wind) HH (High wind) HH (High wind) HH (High wind) L (Low wind) HH (High wind) L L (Low wind) Normal heating Cooling in Cooling/Heating [A UTO] UL (Ultra low wind) only during compressor-OFF Ta ( ˚ C) Tsc – 0. ...

  • Toshiba RAV-SM1603DT-A - page 56

    – 56 – 5 2 A J K I ( ˚ C) No. 8 Item F reeze pre v entive control (Low temper ature release) Outline of specifications 1) The cooling operation (including Dry operation) is perf or med as follo ws based on the detected temperature of Tc sensor or Tcj sensor . When [J] zone is detected f or 6 minutes (F ollowing figure), the commanded frequency ...

  • Toshiba RAV-SM1603DT-A - page 57

    – 57 – A B L N M ( ˚ C) Tc Tcj No. 9 10 11 Item High-temp . release control Drain pump control (Sold separately) After-heat elimination Outline of specifications 1) The heating operation is perf or med as f ollows based on the detected temperature of Tc sensor or Tcj sensor . • When [M] zone is detected, the commanded frequency is decreased ...

  • Toshiba RAV-SM1603DT-A - page 58

    – 58 – No. 13 Item Filter sign displa y (Except wireless type) ∗ It is provided on the separately sold type TCB-AX21E2. Outline of specifications 1) The operation time of the indoor f an is calculated, the filter reset signal is sent to the remote controller when the specified time (2500H) has passed, and it is displa yed on LCD . 2) When the ...

  • Toshiba RAV-SM1603DT-A - page 59

    – 59 – 7-3. Optional Connector Specifications of Indoor P .C. Board ∗ This option is not provided to o versea models . Function V entilation output Option output Outside error input A UT O up/ down g rille ( ∗ ) FIL TER Option error / Humidifier setting ( ∗ ) CHK Operation chec k DISP Exhibition mode EXCT Demand Connector No. CN32 CN60 CN ...

  • Toshiba RAV-SM1603DT-A - page 60

    – 60 – 7-4. Indoor Print Cir cuit Board RA V -SM1403DT -A, RA V -SM1603DT -A <MCC-1403> Drain pump output Power transformer (Primary side) (AC240V) Optional power supply AC fan output EXCT Filter/Option error input T A sensor Float SW ∗ Short plug is inserted ∗ 1 No function Outside error input TCJ sensor TC2 sensor TCI sensor CHK DIS ...

  • Toshiba RAV-SM1603DT-A - page 61

    – 61 – 7-5. Outdoor Print Cir cuit Board RA V -SM1603A T -E, RA V -SM1603A TZ-E, RA V -SM1603A TZG-E In ver ter P .C. board <MCC-1535> [IPDU1] Electrolytic condenser ( – ) Electrolytic condenser (+) Communication between I/F and comp IPDU Between f an IPDU and comp IPDU +5V +12V Reactor Reactor +7V GND Compressor out put ...

  • Toshiba RAV-SM1603DT-A - page 62

    – 62 – Noise filter P .C. boar d <MCC-1551> ...

  • Toshiba RAV-SM1603DT-A - page 63

    – 63 – Model selection jumpers (A vailab le only ser vice P .C. board) J800 to J803 Refrigerant recov er y Switch SW802 Dip s witch for service SW801 EEPROM-IC IC801 P .M.V . CN702 Case thermo. s witch CN500 Communication signal (T o MCC-1535) CN800 TS sensor CN605 Not use CN804 TE sensor CN604 T O sensor CN601 TD sensor CN600 F an motor 1 (Upp ...

  • Toshiba RAV-SM1603DT-A - page 64

    – 64 – 2. Dischar ge temperature release control 1) This function controls the operation frequency , that is, low ers the operation frequency when the discharge temperature has not low er or the discharge temperature has rapidly risen during PMV control. It subdivides the frequency control up to a unit of 0.6 Hz to stabilize the cycle . 2) When ...

  • Toshiba RAV-SM1603DT-A - page 65

    – 65 – 4. Outdoor fan contr ol Allocations of fan tap rev olutions [rpm] SM160 High Low W1 W2 W3 W4 W5 W6 W7 W8 W9 W A WB WC WD WE WF 250 260 260 320 380 480 500 530 610 640 660 720 720 720 780 —— 240 300 400 500 520 550 630 660 700 740 740 740 820 1) Cooling f an control Q The outdoor f an is controlled b y TE, TD , and T O sensors and als ...

  • Toshiba RAV-SM1603DT-A - page 66

    – 66 – 2) Heating f an control Q The outdoor f an is controlled b y TE sensor , T O sensor and the oper ation frequency . (F rom Min. W1 to Max. are controlled according to the follo wing tab le.) R During 3 minutes after star t-up , the f an is fix ed with the maximum f an tap corresponding to zone in the f ollowing tabl e . After then the f a ...

  • Toshiba RAV-SM1603DT-A - page 67

    – 67 – 6. Short intermittent operation preventive contr ol 1) F or 3 to 10 minutes after operation star t, in some cases, the compressor does not stop to protect the compressor e ven if receiving the thermostat-OFF signal from indoor . How ev er it is not abnor mal status. (The operation continuance differs according to the oper ation status.) ...

  • Toshiba RAV-SM1603DT-A - page 68

    – 68 – 1 0 . Defr ost contr ol Q In heating operation, defrost operation is perf or med when TE sensor temperature satisfies any condition in A zone to D z one. R The defrost operation is immediately finished if TE sensor temperature has become 12° C or more, or it also is finished when condition of 7° C < TE < 12° C has continued for ...

  • Toshiba RAV-SM1603DT-A - page 69

    – 69 – T rouble Confirmation of chec k code display Check defective position and parts. →→ 9. INDOOR UNIT TR OUBLESHOO TING 9-1. Summary of T r oub leshooting <Wired remote controller type> 1. Bef ore tr oubleshooting 1) Required tools/instruments • + and – scre wdrivers , spanners, radio cutting pliers , nippers, push pins f or r ...

  • Toshiba RAV-SM1603DT-A - page 70

    – 70 – 9-2. T roub leshooting 9-2-1. Check Code List (Indoor) (Indoor unit detected) ² When this warning was detected before group construction/address check finish at po wer supply was turned on, the mode shifts automatically to A UTO address setup mode . (Remote controller detected) (Central control de vices detected) NO TE: Ev en for the sa ...

  • Toshiba RAV-SM1603DT-A - page 71

    – 71 – Err or mode detected b y indoor unit Operation of diagnostic function Check code E03 E04 E08 L03 L07 L08 L09 L30 P10 P19 P31 F01 F02 F10 F29 E10 E18 Cause of operation No communication from remote controller (including wireless) and communication adapter The serial signal is not output from outdoor unit to indoor unit. • Miswiring of i ...

  • Toshiba RAV-SM1603DT-A - page 72

    – 72 – Err or mode detected b y remote contr oller or central contr oller (TCC-LINK) ∗ 2 The check code cannot be displa yed b y the wired remote controller . (Usual operation of air conditioner becomes una v ailable .) F or the wireless models, an error is notified with indication lamp . ∗ 3 This trouble is related to comm unication of rem ...

  • Toshiba RAV-SM1603DT-A - page 73

    – 73 – 9-2-2. Diagnostic Pr ocedure f or Each Check Code (Indoor Unit) Check code [E01 error] Is inter-unit cable of A and B normal? Is group control operation? Is power of all indoor units turned on? Is power supplied to remote controller? AB terminal: Appro x. DC18V Are 2 remote controllers set without master unit? Are 2 master units set in 2 ...

  • Toshiba RAV-SM1603DT-A - page 74

    – 74 – [E04 error] Is there no disorder of power supply? Does outdoor operate? Is group address setup of remote controller correct? Are wiring in indoor unit and 1, 2, 3 inter-unit cables correct? Are wirings of ter minal bloc ks (1, 2, 3) wired to CN04 normal? Does D502 (Orange LED) flash after power supply turned on again? Check indoor P .C . ...

  • Toshiba RAV-SM1603DT-A - page 75

    – 75 – Is not yet capacity setting of indoor unit set up? Is group control operation? Is power of all indoor units turned on? Is T win or T riple control? Is inter-unit cable of A and B normal? Is there no contact error of indoor/outdoor inter-unit cable (Signal line) of the main unit? Is there no disconnection or contact error of connector on ...

  • Toshiba RAV-SM1603DT-A - page 76

    – 76 – [L20 error] Is group operation carried out? Do outside de vices nor mally work? Check cause of oper ation. Check corresponding indoor unit/outdoor unit. Are outside de vices of connector CN80 connected? Is not the multiple same central control system addresses connected? Is there check code on sub remote controller in main and sub remote ...

  • Toshiba RAV-SM1603DT-A - page 77

    – 77 – Does float switch work? Does drain pump work? Is circuit wiring normal? Is connection of T A sensor connector (CN104 on indoor P .C. board) correct? Are characteristics of T A sensor resistance value normal? Check indoor P .C. board (MCC -1403). Defect → Replace ∗ Refer to T A sensor (T emperature-Resistance value characteristic tabl ...

  • Toshiba RAV-SM1603DT-A - page 78

    – 78 – [P19 error] Chec k method of outdoor P .C. board operation (Self-hold valve type : SP110, SP140) 1) Set SW804 of Dip switch as the f ollowing figure and then push SW801 f or appro x. 1 second to check e xchange operation to cooling cycle/heating cycle. • P ower is turned on f or approx. 10 seconds. • When checking again, chec k opera ...

  • Toshiba RAV-SM1603DT-A - page 79

    – 79 – [F02 error] Correct connection of connector . Are characteristics of TC sensor resistance value normal? Is connection of TC sensor connector (CN101 on Indoor P .C. board) correct? ∗ Refer to TC sensor (T emperature-Resistance value characteristic table) Replace TC sensor . Check indoor P .C. board (MCC -1403). Defect → Replace Correc ...

  • Toshiba RAV-SM1603DT-A - page 80

    – 80 – [C06 error] (TCC-LINK central contr oller) Check centr al controller . Def ect → Replace Is there no noise source? Did a power f ailure occur? Is not the source power supply turned on? Is there no connection error of power supply cab le? Are A and B communication lines normal? Are U3 and U4 communication lines normal? Correct communica ...

  • Toshiba RAV-SM1603DT-A - page 81

    – 81 – [E03 err or] (Master indoor unit) [E03 error] is detected when the indoor unit cannot receiv e a signal from the remote controller (also central controller). Chec k A and B remote controllers and communication lines of the central control system U3 and U4. As communication is impossib le , this chec k code [E03] is not display ed on the ...

  • Toshiba RAV-SM1603DT-A - page 82

    – 82 – Resistance (k Ω ) (50˚C or low er) Resistance (k Ω ) (50˚C or higher) 0 0 50 100 150 200 0 5 10 15 20 10 20 30 40 50 60 70 80 90 100 T emperature ( ˚ C) Resistance (k Ω ) 0 0 10 20 30 40 10 20 30 40 50 60 70 80 90 100 T emperature ( ˚ C) T emperature (°C) 0 10 20 25 30 40 50 60 70 80 90 100 Resistance value (k Ω Ω Ω Ω ...

  • Toshiba RAV-SM1603DT-A - page 83

    – 83 – 10. OUTDOOR UNIT TR OUBLESHOO TING 10-1. Summary of T r oub leshooting <Wired remote controller type> 1. Bef ore tr oubleshooting 1) Required tools/instruments • + and – scre wdrivers , spanners, radio cutting pliers , nippers, push pins f or reset s witch • T ester , ther mometer , pressure gauge, etc. 2) Confir mation point ...

  • Toshiba RAV-SM1603DT-A - page 84

    – 84 – <Wireless remote contr oller type> 1. Bef ore tr oubleshooting 1) Required tools/instruments • + and – screwdriv ers, spanners , radio cutting pliers, nippers , etc. • T ester , ther mometer , pressure gauge, etc. 2) Confir mation points before chec k a) The follo wing operations are normal. 1. Compressor does not operate. ? ...

  • Toshiba RAV-SM1603DT-A - page 85

    – 85 – 10-2. T roub leshooting 10-2-1. Outline of Judgment The primar y judgment to check whether a troub le occurred in the indoor unit or outdoor unit is carried out with the f ollowing method. Method to judge the erroneous position b y flashing indication on the displa y par t of the indoor unit (sensors of the receiving par t) The indoor un ...

  • Toshiba RAV-SM1603DT-A - page 86

    – 86 – ∗ 1: These are representativ e e xamples and the check code diff ers according to the outdoor unit to be combined.                Lamp indication Operation Timer Ready Alternate flash Operation Timer Ready Alternate flash Operation Timer Ready Simultaneous flash Operation Timer Ready Flash O ...

  • Toshiba RAV-SM1603DT-A - page 87

    – 87 – 10-2-2. Others (Other than Chec k Code) Lamp indication Operation Timer Ready Simultaneous flash Operation Timer Ready Alternate flash Check code — — Cause of troub le occurrence During test r un Disagreement of cool/heat (A utomatic cool/heat setting to automatic cool/heat prohibited model, or setting of heating to cooling-only mode ...

  • Toshiba RAV-SM1603DT-A - page 88

    – 88 – 10-2-3. Chec k Code List (Outdoor) ¡ : Go on, ¥ : Flash, l : Go off AL T (Alternate): Alternate flashing when there are two flashing LED SIM (Simultaneous): Simultaneous flashing when there ar e two flashing LED ² When this war ning was detected before g roup construction/address check finish at power supply was turned on, the mode sh ...

  • Toshiba RAV-SM1603DT-A - page 89

    – 89 – ¡ : Go on, ¥ : Flash, l : Go off AL T (Alternate): Alternate flashing when there are two flashing LED SIM (Simultaneous): Simultaneous flashing when there are two flashing LED Remote controller indication F01 F02 F10 F29 P01 P10 P12 P31 — — L20 — Sensor lamp part Block indication Operation Timer Ready Flash ¥¥ l AL T ¥¥ l AL ...

  • Toshiba RAV-SM1603DT-A - page 90

    – 90 – Err or mode detected b y indoor unit Operation of diagnostic function Check code E03 E04 E08 L03 L07 L08 L09 L30 P01 P10 P12 P19 P31 F01 F02 F10 F29 E10 E18 Cause of operation No communication from remote controller (including wireless) and communication adapter The serial signal is not output from outdoor unit to indoor unit. • Miswir ...

  • Toshiba RAV-SM1603DT-A - page 91

    – 91 – Err or mode detected b y remote contr oller or central contr oller (TCC-LINK) ∗ 2 The check code cannot be displa yed b y the wired remote controller . (Usual operation of air conditioner becomes una v ailable .) F or the wireless models, an error is notified with indication lamp . ∗ 3 This trouble is related to comm unication of rem ...

  • Toshiba RAV-SM1603DT-A - page 92

    – 92 – Err or mode detected b y outdoor unit Operation of diagnostic function Check code Indoor unit F04 F06 F08 H01 H02 H03 H06 L29 L31 ∗ 1 P03 P04 P22 P26 P29 Cause of operation Disconnection, shor t of discharge temp . sensor (TD) Disconnection, shor t of outdoor temp . sensor (TE, TS) Disconnection, shor t of outside temp . sensor (T O) C ...

  • Toshiba RAV-SM1603DT-A - page 93

    – 93 – 10-2-4. Distinction of error mode b y LED indication of outdoor unit On the T ype AP112, AP140 and AP160, a Dip s witch (SW801) and LED are provided on the P .C . board of the outdoor unit. Exchanging this Dip s witch enables users to kno w the status of the outdoor unit in that time. Lighting status of LED enables users to kno w the dis ...

  • Toshiba RAV-SM1603DT-A - page 94

    – 94 – Y ou can perform fault diagnosis of the outdoor unit with the LEDs on the P .C . board of the outdoor unit in addition to check codes displa yed on the wired remote controller of the indoor unit. Use the LEDs and check codes f or various chec ks. Details of check codes displa yed on the wired remote controller of the indoor unit are desc ...

  • Toshiba RAV-SM1603DT-A - page 95

    – 95 – 10-2-5. Diagnostic Pr ocedure for Eac h Check Code (Indoor Unit) Check code [E01 error] Is inter-unit cable of A and B normal? Is group control operation? Is power of all indoor units turned on? Is power supplied to remote controller? AB terminal: Appro x. DC18V Are 2 remote controllers set without master unit? Are 2 master units set in ...

  • Toshiba RAV-SM1603DT-A - page 96

    – 96 – [E04 error] Correct connection of connector . Replace IPDU. Check indoor P .C. board. Defect → Replace Check item code [14]. Correct inter -unit cable. Correct connection of connector . Check/Correct charged refrigerant amount. Check indoor P .C. board. Defect → Replace Replace IPDU. Correct connection of connector . ∗ As shown in ...

  • Toshiba RAV-SM1603DT-A - page 97

    – 97 – Is there no disorder of power supply? Check pow er supply voltage . Correct lines. Check and eliminate noise , etc. YES NO Check indoor control P .C . board. Def ect → Replace Is group control operation? Is power of all indoor units turned on? Is T win or T riple control? Is inter-unit cable of A and B normal? Is there no contact error ...

  • Toshiba RAV-SM1603DT-A - page 98

    – 98 – [L09 error] YES YES NO NO NO NO Check cause of operation. Check central controller (including network adapter). Defect → Replace Check indoor P .C. board. Defect → Replace YES YES YES YES YES NO NO Do outside devices normally work? Are outside devices of connector CN80 connected? Is the central controller [98] displayed? Is the indoo ...

  • Toshiba RAV-SM1603DT-A - page 99

    – 99 – Replace fan motor . Check indoor P .C. board. Defect → Replace Check the corresponding indoor unit and outdoor unit. Is group operation carried out? Is the condenser normal? Isn’t there mechanical lock of the fan motor? Is there check code on the follo wer unit of main/sub remote controllers? Isn ’ t there any connection error/disc ...

  • Toshiba RAV-SM1603DT-A - page 100

    – 100 – Does float switch work? Does drain pump work? Is circuit wiring normal? Is connection of T A sensor connector (CN104 on indoor P .C. board) correct? Are characteristics of T A sensor resistance value normal? ∗∗ Check indoor P .C. board. Defect → Replace ∗∗ Refer to 10-2-6. Relational graph of temperature sensor resistance valu ...

  • Toshiba RAV-SM1603DT-A - page 101

    – 101 – [P12 error] Does the fan rotate without trouble when handling the fan with hands? Remove connectors CN333 and CN334 of indoor unit P .C. board (MCC -1402). Is output of indoor fan motor position detection signal correct? ∗ 3 Is resistance value of fan motor connector CN334 motor side of indoor P .C. board correct? ∗ 2 Are resistance ...

  • Toshiba RAV-SM1603DT-A - page 102

    – 102 – [P22 error] CN300 : Motor coil winding CN301 : Motor position detection ∗ CN301, CN303 : Motor coil winding CN300, CN302 : Motor position detection Are connections of CN300, CN301, CN302 and CN303 of P .C. board correct? Does the f an rotate without trouble when handling the f an with hands under condition of removing CN300, CN301, CN ...

  • Toshiba RAV-SM1603DT-A - page 103

    – 103 – [P19 error] Check 4-way valve Defect → Replace Check and replace electron expansion valve. Replace TC sensor . Correct connection of connector . Replace TC sensor . Check and correct circuit. Check indoor P .C. board. Defect → Replace Check CDB P .C. board. Defect → Replace Check indoor P .C. board. Defect → Replace Check CDB P ...

  • Toshiba RAV-SM1603DT-A - page 104

    – 104 – [F01 error] Improve the power supply line. Check IPDU. Defect → Replace. Replace IPDU. Check defective rear short of compressor . Defect → Replace Check and correct circuit cables. Correct connection of connector . Check and correct reactor connection. Replace TCJ sensor . Correct connection of connector . Check indoor P .C. board. ...

  • Toshiba RAV-SM1603DT-A - page 105

    – 105 – [P29 error] Is not earthed? Is not winding opened? Compressor error → Replace Correct connection of connector . Replace TE and TS sensors. Check and correct circuit cabling such as cabling to compressor . Check IPDU P .C. board. Defect → Replace Check CDB. Defect → Replace ∗ Refer to relational graph of temperature sensor resist ...

  • Toshiba RAV-SM1603DT-A - page 106

    – 106 – Correct connection of connector . Replace TO sensor . Correct connection of connector . Improve and eliminate the cause. Improve power line. Compressor lock → Replace Correct mounting. Check cabling between IPDU and CDB and connector . IPDU P .C. board error Defect → Replace IPDU P .C. board error Defect → Replace Check IPDU and C ...

  • Toshiba RAV-SM1603DT-A - page 107

    – 107 – [P03 error] [H01 error] Check parts. Defect → Replace Correct the cabling and connection of connector . Replace TD sensor . Check and correct the charged refrigerant amount. Improve and delete the cause Check CDB. Defect → Replace Improve power line. Improve and delete the cause. Check IPDU. Defect → Replace Is power voltage norma ...

  • Toshiba RAV-SM1603DT-A - page 108

    – 108 – [P04 error] Does PMV normally operate? Is fan motor normal? Is connection of cabling connector normal? Do not TD and TO sensors come off the detection part? Is connection of connector normal? Does cooling outdoor fan normally operate? Are characteristics of TD, TO , TC sensor resistance values normal? ∗ Is high-voltage protective oper ...

  • Toshiba RAV-SM1603DT-A - page 109

    – 109 – [97 err or] (Central contr oller) Correct communication line. Correct connection of connector . Check connection of A and B terminal blocks. Correct communication line of remote controller . Clear the check code. T urn on main power supply . Check central controller . Defect → Replace Check network adapter P .C. board (MCC-1401) and t ...

  • Toshiba RAV-SM1603DT-A - page 110

    – 110 – [E03 err or] (Master indoor unit) [E03 error] is detected when the indoor unit cannot receiv e a signal sent from the main remote controller (and central controller). In this case, chec k the communication cab les of the remote controllers A and B , the central control system X and Y . As communication is disab led, [E03] is not displa ...

  • Toshiba RAV-SM1603DT-A - page 111

    – 111 – 10-2-6. Relational Graph of T emperature Sensor Resistance V alue and T emperature Resistance (k Ω ) Resistance (k Ω ) T emperature [˚C] T emperature [˚C] T emperature [˚C] T emperature [˚C] Resistance (k Ω ) ( 10 ˚ C or low er) Resistance (k Ω ) (50 ˚ C or low er) Resistance (k Ω ) (50 ˚ C or higher) Resistance (k Ω ...

  • Toshiba RAV-SM1603DT-A - page 112

    – 112 – 11. REPLA CEMENT OF SER VICE P .C. BO ARD 11-1. Indoort Unit <Note: when replacing the P .C. board f or indoor unit ser vicing> The nonv olatile memor y (hereafter called EEPROM, IC503) on the indoor unit P .C. board bef ore replacement includes the model specific type inf or mation and capacity codes as the factory-set value and ...

  • Toshiba RAV-SM1603DT-A - page 113

    – 113 – [2] P .C. Board f or indoor unit ser vicing replacement pr ocedures Step 1 Replace the P .C . board to the P .C . board for indoor unit servicing. On the new P .C . board, set the same setting of the jumper wire and setting of shor tcut connection connec- tor as those of the P .C . board before replacement. Step 2 According to the syste ...

  • Toshiba RAV-SM1603DT-A - page 114

    – 114 – 36 5 1 4 2 [3] Writing the setting data to EEPROM The settings stored in the EEPROM of the P .C. board for indoor unit servicing are the factory-set values. Step 1 Push SET , CL and TEST buttons on the remote controller sim ultaneously for more than 4 seconds . ∗ In the group control operation, the unit No . display ed f or the first ...

  • Toshiba RAV-SM1603DT-A - page 115

    – 115 – DN 01 02 03 06 OF 10 11 12 13 14 1E 28 2b 31 32 40 60 Item Filter sign lighting time Filter pollution le ve Central control address Heating suction temperature shift Cooling only T ype Indoor unit capacity System address Indoor unit address Group address T emperature range of cooling/heating automatic SW control point P ower f ailure au ...

  • Toshiba RAV-SM1603DT-A - page 116

    – 116 – 12. SETUP A T LOCAL SITE AND O THERS 12-1. Indoor Unit 12-1-1. T est Run Setup on Remote Controller <Wired remote controller> 1. When pushing TEST b utton on the remote controller f or 4 seconds or more, “TEST” is displa yed on LC displa y . Then push ON / OFF button. • “TEST” is display ed on LC displa y during operatio ...

  • Toshiba RAV-SM1603DT-A - page 117

    – 117 – 12-1-3. LED Displa y on P .C. Boar d 1. D02 (Red) • Goes on at the same time when pow er was tur ned on (Main microcomputer operates and goes on.) • Flashes with 1-second inter v al (e very 500ms): When EEPR OM is not provided or writing was an error . • Flashes with 10-seconds inter val (e very 5S): When the mode is DISP 2. D203 ...

  • Toshiba RAV-SM1603DT-A - page 118

    – 118 – Function selection item No. (DN) list DN 01 03 06 10 11 12 13 14 1E 28 2A 2b 31 32 40 60 C2 D0 Item Filter sign lighting time Central control address Heating suction temp . shift T ype Indoor unit capacity Line address Indoor unit address Group address In automatic cooling/heating, temp . width of cool → heat, heat → cool mode selec ...

  • Toshiba RAV-SM1603DT-A - page 119

    – 119 – 12-1-5. Wiring and Setting of Remote Contr oller Control (Setup method) One or multiple indoor units are controlled b y 2 remote controllers. (Max. 2 remote controllers are connectab le .) <Wired remote controller> How to set wired remote contr oller as sub remote contr oller Change DIP s witch inside of the rear side of the remot ...

  • Toshiba RAV-SM1603DT-A - page 120

    – 120 – 12-1-6. Monitor Function of Remote Contr oller Switch n Calling of sensor temperature displa y <Contents> Each data of the remote controller , indoor unit and outdoor unit can be understood by calling the service monitor mode from the remote controller . <Procedure> 1 Push TEST + CL buttons sim ultaneously for 4 seconds to c ...

  • Toshiba RAV-SM1603DT-A - page 121

    – 121 – n Calling of err or histor y <Contents> The error contents in the past can be called. <Pr ocedure> 1 Push SET + TEST buttons sim ultaneously for 4 seconds or more to call the service chec k mode . Ser vice Check goes on, the item code 01 is displa yed, and then the content of the latest alar m is displa yed. The number and e ...

  • Toshiba RAV-SM1603DT-A - page 122

    – 122 – n Indoor unit power -ON sequence • In a group operation, if the indoor unit which w as f ed power after judgment of automatic address cannot receiv e regular communication from the master unit and regular communication on identical pipe within 120 seconds after pow er w as tur ned on, it reboots (system reset). → The operation star ...

  • Toshiba RAV-SM1603DT-A - page 123

    – 123 – 12-2. Setup at Local Site / Other s Model name: TCB-PCNT30TLE2 12-2-1. TCC-LINK Adapter (For TCC-LINK Central Control) 1. Function This model is an optional P .C . board to connect the indoor unit to TCC-LINK (Central controller). 2. Micropr ocessor block dia gram 3. TCC-LINK wiring connection CA UTION 1) When controlling customized set ...

  • Toshiba RAV-SM1603DT-A - page 124

    – 124 – • Use 2-core with no polar wire. • Match the length of wire to wire length of the central control system. If mix ed in the system, the wire length is lengthened with all indoor/outdoor inter-unit wire length at side. • T o prev ent noise trouble, use 2-core shield wire . • Connect the shield wire by closed-end connection and app ...

  • Toshiba RAV-SM1603DT-A - page 125

    – 125 – 6. External view of P .C. board assemb ly 7. Address setup In addition to set up the central control address , it is necessar y to change the indoor unit number . (Line/Indoor/Group address). F or details, ref er to TCC-LINK Adapter Installation Manual. 12-3. Ho w to Set up Central Control Ad dress Number When connecting the indoor unit ...

  • Toshiba RAV-SM1603DT-A - page 126

    – 126 – How to confirm the central contr ol address (New function f or AMT32 remote controller) <Procedure> It can be confirmed ev en dur ing operation or stopping. 1 Push UNIT LOUVER b utton for 4 seconds or more. ò 2 In the frame at left side of the remote controller screen, the lighting set contents are display ed. During unset time, ...

  • Toshiba RAV-SM1603DT-A - page 127

    – 127 – Setup of line address of outdoor unit, indoor unit address, and group address Completion of cabling work Turn on power of outdoor unit. Turn on power of outdoor unit. Connect one remote controller with one indoor unit (1 : 1) tentatively with communication cable. END Turn on power of outdoor unit. Set to all indoor units one by one. Do ...

  • Toshiba RAV-SM1603DT-A - page 128

    – 128 – 13-2. Address Setup & Gr oup Control <T erminology> Indoor unit No . : N - n = Outdoor unit line address N (Max. 30) - Indoor unit address n (Max. 64) Group address : 0 = Single (Not group control) 1 = Master unit in group control 2 = Sub unit in group control Master unit (= 1) : The representativ e of multiple indoor units in ...

  • Toshiba RAV-SM1603DT-A - page 129

    – 129 – 4. Single group operation • Each indoor unit controls the outdoor unit individually . 5. Multiple groups operation (Manual address setting) • Header unit: The header unit receiv es the indoor unit data (thermo status) of the f ollo w er (Without identical line address & indoor/outdoor serial) and then finally controls the outdoo ...

  • Toshiba RAV-SM1603DT-A - page 130

    – 130 – 13-2-2. A utomatic Address Example from Unset Address (No mis wiring) 1. Standard (One outdoor unit) 1) Single 2) T win 3) T r iple 2-1 Single T win T r iple 1-1 1-2 3-1 3-2 3-3 2-1 Sub/Header 1-1 Sub/Header 3-1 Master/Header 8-1 Sub/Header 2-1 Sub/Header 1-1 Sub/Header 2-3 Master/Follo wer 3-1 Sub/Header 3-3 Sub/Follo wer 1-2 Sub/Follo ...

  • Toshiba RAV-SM1603DT-A - page 131

    – 131 – (Example of 2-lines cabling) (Real line: Cabling, Broken line: Refrigerant pipe) For the above example, perform setting by connecting singly the wired remote controller without remote controller inter-unit cable. Group address Individual : 0000 Master unit : 0001 Sub unit : 0002 In case of group control Outdoor Indoor A B A B 1 2 3 Indo ...

  • Toshiba RAV-SM1603DT-A - page 132

    – 132 – 1 2 END Operation <Operation procedure> 2 1 SET TIME TIMER SET TEST FIL TER RESET TEMP . CL FAN SA VE SWING/FIX VENT MODE ON / OFF UNIT LOUVER 1 2 3 END <Operation procedure> 3 1 2 SET TIME TIMER SET TEST FIL TER RESET TEMP . CL FAN SA VE SWING/FIX VENT MODE ON / OFF UNIT LOUVER n Confirmation of indoor unit No. position 1. ...

  • Toshiba RAV-SM1603DT-A - page 133

    – 133 – 2 4 3 6 9 6 8 5 7 1 Top plate Foaming part 14. DET A CHMENTS 14-1. Indoor Unit REQUIREMENT • At the ser vice replacing time of the heat e xchanger , the follo wing tools are necessar y . Prepare them bef ore the ser vice work. • Necessar y tools: Plus scre wdr iver , monke y wrench, spanner , etc CA UTION • Be sure to place the he ...

  • Toshiba RAV-SM1603DT-A - page 134

    – 134 – No. 2 W ork procedure Remov e the foaming par t. Note) Remov e the foaming par t carefully so that cor ners of the f oaming par t of the inner plate are not chipped off by being caught. Explanatory drawing 2. How to replace the parts (Continued) 3 4 5 Remov e the r ight side plates (2) and (3). Note) Remov e the side plates so as not to ...

  • Toshiba RAV-SM1603DT-A - page 135

    – 135 – No. 6 2. How to replace the parts (Continued) W ork procedure T ake off the pipe fixing brac ke t (1) and the drain shield plate . Explanatory drawing 7 8 9 Remov e the left side plate. Remov e the inner foaming plate and the insulator material. 1) Pull off the insulator mate- rial between the drain pan and the mounting plate. 2) T ake ...

  • Toshiba RAV-SM1603DT-A - page 136

    – 136 – REQUIREMENT • At the ser vice replacing time of the f an motor , the follo wing tools are necessar y . Prepare them bef ore the ser vice work. • Necessar y tools: Plus screwdriv er , L-shape he xagonal wrench (For Ø M8mm (F ace to face 4mm)), ratchet wrench (F or Ø 6mm nut (F ace to f ace 10mm)), monke y wrench, spanner , etc. CA ...

  • Toshiba RAV-SM1603DT-A - page 137

    – 137 – 4. How to replace the parts (Continued) No. 2 W ork procedure Remov e the electr ic par ts box. Note) • When keeping the electric par ts bo x, be sure not to damage or take off the sensor lead wire connected to the main unit. Explanatory drawing 3 4 5 6 Remov e the r ight side plates (1) and (2). 1) First remov e the r ight side plate ...

  • Toshiba RAV-SM1603DT-A - page 138

    – 138 – 4. How to replace the parts (Continued) No. 7 W ork procedure Remov e the reinforcing plate . Note) • The reinf orcing plate is provided to protect the transpor tation. Scrap it after unpac king because it is unnecessar y to attach when reassembling. Explanatory drawing 5. Assembling w ork after replacing fan motor • After replacing ...

  • Toshiba RAV-SM1603DT-A - page 139

    – 139 – 6. How to replace the sensor No. 1 W ork procedure As same as the work procedure of the f an motor replacing, remov e the r ight side plates (1) and (2). Explanatory drawing 2 3 Remov e the shielding plate. As the shielding plate is assembled with scre ws, tak e the fixing screws off to divide the plate . Cut the b unding band which tie ...

  • Toshiba RAV-SM1603DT-A - page 140

    – 140 – 6. How to replace the sensor (Contin ued) No. 4 W ork procedure 7. How to c lean the drain por t No. 1 W ork procedure As same as the work procedure of the sensor replacing, remov e the r ight side plates and the shielding plate, and then carr y on the wor k. Explanatory drawing Inser t the connectors into the specified positions on P . ...

  • Toshiba RAV-SM1603DT-A - page 141

    – 141 – Heat exchanger P ar tition plate Fin guard Motor base Motor base Reactor assembly V alve fixing plate T op plate T op plate F ront panel F ront panel Side cabinet Side cabinet Motor base Air outlet Air outlet cabinet cabinet Air outlet cabinet T op plate F ront panel Side cabinet 14-2. Outdoor Unit No. 1 P art name Common procedure Pr o ...

  • Toshiba RAV-SM1603DT-A - page 142

    – 142 – No. 4 P art name Replacement of electric par ts Common procedure Pr ocedure 1. Detachment 1) Carry out wor ks of 1 of 1 and 3 . 2) Remov e the connectors connected to CDB board. (Connector of pow er supply and upper side f an motor) • Unlock the loc k of the housing par t and then remov e the connectors. 3) Cut the b undling band whic ...

  • Toshiba RAV-SM1603DT-A - page 143

    – 143 – No. 7 P art name Replacement of electric par ts Electrolytic condenser Pr ocedure 1. Detachment 1) Carry out wor ks of 1 of 1 , 3 and 4 . 2) Remov e the lead wire connected to the terminal block. (IPDU crossov er wire) 3) Remov e the connector connected to the noise filter . (IPDU crossov er wire) 4) Remov e the lead wire connected to t ...

  • Toshiba RAV-SM1603DT-A - page 144

    – 144 – No. 8 P art name Replacement of electric par ts IPDU P .C . board Pr ocedure 1. Detachment 1) Carr y out works of 1 of 1 , 3 and 4 . 2) Remov e the lead wire connected to the terminal bloc k. (IPDU crossov er wire, reactor lead wire) 3) Remov e the lead wire connected to the noise filter . (Fuse crossov er wire, po wer supply crosso ver ...

  • Toshiba RAV-SM1603DT-A - page 145

    – 145 – No. 9 P art name Reactor assembly Pr ocedure 1. Detachment 1) Carry out wor ks of 1 of 1 , 3 and 4 . 2) Remov e lead wires connected to the terminal bloc k. 3) Cut the bundling band which binds the rector lead wires. Remarks Service reactor N side L side Marking No Ye s 1. Assembly 1) Assemble the reactor with procedure 7) to 1). X REQU ...

  • Toshiba RAV-SM1603DT-A - page 146

    – 146 – No. 10 P art name F an motor Pr ocedure 1) Carr y out works of 1 and wor k of 2 . 2) Remov e the flange nut fixing the f an motor and the propeller f an. ∗ The flange nut is loosened b y turning it clockwise. (When tightening it, turn it counterclockwise.) 3) Remov e the propeller fan. 4) Remov e the connector for the f an motor from ...

  • Toshiba RAV-SM1603DT-A - page 147

    – 147 – No. 11 P art name Compressor Compressor lead Remarks Pr ocedure 1. Remov al of defective compressor 1) Recov er the refrigerant gas. 2) Carr y out work of item 1 of 1 and wor k of 3 . 3) Remov e the piping panel (F ront). Remov e the piping panel (F ront) and scre ws of the bottom plate. (He xagonal screw Ø 4 × 10, 2 pcs .) Remov e sc ...

  • Toshiba RAV-SM1603DT-A - page 148

    – 148 – No. 11 P art name Compressor Compressor lead (Continued) Remarks Pr ocedure 2. Mounting of compressor 1) Mount the compressor in the re verse procedure f or remov al. Note) • After replacement of the compressor , necessarily replace the compressor lead wires. (Spare par ts code: 43160591) In this time, wind compressor lead around the ...

  • Toshiba RAV-SM1603DT-A - page 149

    – 149 – Hooking claw Concave part PMV main unit Positioning projection PMV coil F an guard Bell mouth Discharge port cabinet Earth screw Earth screw T erminal block T erminal block mounting plate mounting plate Bundling band Bundling band (Binding) (Binding) Bundling band Bundling band 4-way valve lead 4-way valve lead T erminal block T erminal ...

  • Toshiba RAV-SM1603DT-A - page 150

    – 150 – 15. EXPLODED VIEWS AND P ARTS LIST 15-1. Indoor Unit RA V -SM1403DT -A, RA V -SM1603DT -A 203 202 206 210 214 216 215 201 212 213 208 204 207 211 205 207 209 213 ...

  • Toshiba RAV-SM1603DT-A - page 151

    – 151 – Location P ar t No. Description No. 201 43172203 P an Ass ’ y , Drain 202 4312C041 Motor , F an, AC240V , 50Hz, 600W 203 43019830 Bushing 204 43020352 F an 205 43020353 F an 206 43170244 Hose, Drain, 25A 207 43139167 Bell Mouth 208 43139154 Band, Motor , Left 209 43139155 Band, Motor , Right 210 43179135 Band, Hose, 37-40 211 431S8089 ...

  • Toshiba RAV-SM1603DT-A - page 152

    – 152 – Location P ar t No. Description No. 401 43050425 Sensor TC (F6) Ass ’ y , Ser vice 402 43050426 Sensor T A, Service 403 43055529 Capacitor , AC450V , 8µF 404 43060859 Fuse Block, 30A, 250V , ∗ FH153-PB 405 43154175 Rela y , L Y1F , A C220 / 240V 406 43158204 T ransf or mer , TT13 (A C220 – 240V) 407 43160565 T er minal Block, 3P ...

  • Toshiba RAV-SM1603DT-A - page 153

    – 153 – 15-2. Outdoor Unit RA V -SM1603A T -E, RA V -SM1603A TZ-E, RA V -SM1603A TZG-E 14 11 10 12 19 38 39 15 20 22 2 41 1 40 21 5 23 17 18 28 35 34 4, 25 27, 37 3 24 31, 33 26, 32 16 6, 9 13 30 29 42 7, 8, 36 ...

  • Toshiba RAV-SM1603DT-A - page 154

    – 154 – Location P art No. Description No. 1 43019904 Holder , Sensor , SUS 2 43032441 Nipple, Dr ain 3 43041794 Compressor , DA422A3F-25M 4 43047246 Bonnet, 3/8 IN 5 43047669 Nut, Flange 5 43197164 Nut, Flange, SUS304-WSB 6 43049739 Cushion, Rubber 7 43050407 Thermostat, Bimetal 8 43063317 Holder , Ther mostat 9 43097212 Nut 9 43197174 Nut, Co ...

  • Toshiba RAV-SM1603DT-A - page 155

    – 155 – 716, 717 712 718 711 705 714, 715 706 713 707 708 702 704 718 701 703 709, 710 RA V -SM1603A T -E, RA V -SM1603A TZ-E, RA V -SM1603A TZG-E Location P ar t No. Description No. 701 43050425 Sensor TC (F6) Ass ’ y , Ser vice 702 43063325 Holder , Sensor , 6 - 6.35, 8 703 43150319 Sensor Ass ’ y , TD (F4), Ser vice 704 43155211 Capacito ...

  • Toshiba RAV-SM1603DT-A - page 156

    W ARNINGS ON REFRIGERANT LEAKA GE For the amount of charge in this example: The possible amount of leaked refrigerant gas in rooms A, B and C is 10kg. The possible amount of leaked refrigerant gas in rooms D, E and F is 15kg. NOTE 2 : The standards for minimum room volume are as follows. (1) No partition (shaded portion) (2) When there is an effect ...

  • Toshiba RAV-SM1603DT-A - page 157

    TOSHIBA C ARRIER CORPORA TION 23-17, T A KANA W A 3 CHOME, MINA TOKU, TOK YO , 108-8580, JAP AN Cop yright © 1999 to 2007 T OSHIBA CARRIER CORPORA TION, ALL Rights Reser ved. ...

Manufacturer Toshiba Category Air Conditioner

Documents that we receive from a manufacturer of a Toshiba RAV-SM1603DT-A can be divided into several groups. They are, among others:
- Toshiba technical drawings
- RAV-SM1603DT-A manuals
- Toshiba product data sheets
- information booklets
- or energy labels Toshiba RAV-SM1603DT-A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Toshiba RAV-SM1603DT-A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Toshiba RAV-SM1603DT-A, service manual, brief instructions and user manuals Toshiba RAV-SM1603DT-A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Toshiba RAV-SM1603DT-A.

Similar manuals

A complete manual for the device Toshiba RAV-SM1603DT-A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Toshiba RAV-SM1603DT-A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Toshiba RAV-SM1603DT-A.

A complete Toshiba manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Toshiba RAV-SM1603DT-A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Toshiba RAV-SM1603DT-A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Toshiba RAV-SM1603DT-A, that we can find in the current document
3. Tips how to use the basic functions of the device Toshiba RAV-SM1603DT-A - which should help us in our first steps of using Toshiba RAV-SM1603DT-A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Toshiba RAV-SM1603DT-A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Toshiba RAV-SM1603DT-A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Toshiba RAV-SM1603DT-A?

Use the form below

If you did not solve your problem by using a manual Toshiba RAV-SM1603DT-A, ask a question using the form below. If a user had a similar problem with Toshiba RAV-SM1603DT-A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)