English dropdown-ico

Manual Hobart Q Series

12 pages 1.74 mb
Download

Go to site of 12

Summary
  • Hobart Q Series - page 1

    FORM 14580 Rev. L (Jan. 2002) N S T R U C T I O N S I 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com Q SERIES REACH-IN FOOD ST ORA GE CABINETS Q SERIES REACH-IN ...

  • Hobart Q Series - page 2

    – 2 – Installation, Operation and Care of Q SERIES REA CH-IN FOOD ST ORA GE CABINETS SA VE THESE INSTR UCTIONS GENERAL The Q Series Reach-In Food Storage Cabinets are available as low temperature (0°F), medium temperature (38°F) refrigeration units or hot food storage cabinets (180°F maximum). They may be ordered as one-, two-, or three-sect ...

  • Hobart Q Series - page 3

    – 3 – ASSEMBLY Some components can be removed to allow the cabinet to pass through short or narrow doorways. The door handle can be removed as follows: 1. Remove the screw and bolt from the tumbler. 2. Remove the two mounting screws and the handle assembly (Fig. 1) 3. Replace in reverse order of disassembly. Door(s) and hinges can be removed as ...

  • Hobart Q Series - page 4

    – 4 – LEGS OR CASTERS WARNING : THE CABINET MUST BE BLOCKED AND STABLE BEFORE INSTALLING LEGS OR CASTERS. Legs (Fig. 5) To install the legs, raise and block the reach-in a minimum of 7 " from the floor and thread the legs into the Threaded Holes on the bottom of the cabinet. This unit must be level in order to operate properly. Turn the ad ...

  • Hobart Q Series - page 5

    – 5 – Compressor Mounts Some Q Series units have the compressor specially mounted to help prevent damage during shipment. If the compressor is mounted on shipping blocks, remove the shipping blocks before operating the compressor. If the compressor is mounted on springs, refer to the tag attached to the compressor. Condensate Evaporator Q Serie ...

  • Hobart Q Series - page 6

    – 6 – STANDARD THERMOMETER (Fig. 9) — The standard digital thermometer is calibrated at the factory and does not permit recalibration. OPTIONAL DIAL THERMOMETER — The optional dial thermometer can be recalibrated. Compare the cabinet thermometer with an accurate test thermometer. If there is any variation, contact a Hobart-authorized Refrig ...

  • Hobart Q Series - page 7

    – 7 – ELECTR ONIC DEFROST TIMER (when equipped) If your freezer is equipped with an electronic Defrost Timer, it is located in a control box behind the trim rail at the top of the Reach-In Freezer. To access the the Defrost Timer, remove the Thumbscrew on the left side of the Control Box and slide the Lid to the left (Fig. 11). Save the Thumbsc ...

  • Hobart Q Series - page 8

    – 8 – To Change the Defrost Duration and Bypass the Setting of the Time Clock Begin with the SET CLOCK light blinking rapidly, indicating normal Operation Mode . . . If you want to change the Defrost Duration but not reset the time-of-day, press and hold the PROGRAM button for about 3 seconds until the PROGRAM light starts blinking. Release the ...

  • Hobart Q Series - page 9

    – 9 – How to Set a Custom Defrost Schedule Begin with the defrost timer on normal Operation Mode: The SET CLOCK light is blinking rapidly and the PROGRAM and DEFROST ON lights are off. If all switches are OFF (Fig. 15), the factory preset defrost schedule is enabled: 2 AM , 8 AM , 2 PM , 8 PM . • Determine your own best defrost schedule. The ...

  • Hobart Q Series - page 10

    – 10 – Program Review During normal Operation Mode, with the SET CLOCK light blinking rapidly . . . Press the SET button until the SET CLOCK, PROGRAM, and DEFROST ON lights are lit; then release the SET button and all three lights go off for two seconds. After that, all three lights begin to blink. The number of blinks of a light corresponds to ...

  • Hobart Q Series - page 11

    – 11 – If the Defrost Timer's Battery Loses Power If the SET CLOCK, PR OGRAM and DEFROST ON lights are all b linking, the backup po wer supply (batter y) to the Defrost Timer has weakened. Estimated batter y lif e is 10 years. The timer can continue to function normally after the batter y has weak ened if the timer is reprogrammed. If a po ...

  • Hobart Q Series - page 12

    – 12 – FORM 14580 Rev. L (Jan. 2002) PRINTED IN U.S.A. MAINTENANCE CLEANING Cabinet Clean the inside of the cabinet and the doors weekly with a warm water solution of mild household liquid dishwashing detergent (such as Palmolive green or Ivory). Do not use anything containing grit, abrasive materials, bleach or harsh chemicals. Be cautious wit ...

Manufacturer Hobart Category Refrigerator

Documents that we receive from a manufacturer of a Hobart Q Series can be divided into several groups. They are, among others:
- Hobart technical drawings
- Q Series manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart Q Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart Q Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart Q Series, service manual, brief instructions and user manuals Hobart Q Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart Q Series.

Similar manuals

A complete manual for the device Hobart Q Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart Q Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart Q Series.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart Q Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart Q Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart Q Series, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart Q Series - which should help us in our first steps of using Hobart Q Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart Q Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart Q Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart Q Series?

Use the form below

If you did not solve your problem by using a manual Hobart Q Series, ask a question using the form below. If a user had a similar problem with Hobart Q Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)