English dropdown-ico

Manual Atmel ATA5283

14 pages 0.25 mb
Download

Go to site of 14

Summary
  • Atmel ATA5283 - page 1

    Features • W ake-up Function for a Microcontr oller with Preamble Detection • 1m V rms Sensitivity • 1 µA Standby Current • P ower Supply: 2V to 3.8V • Baud Rate: up to 4 kb ps (ASK Modulation) • Operation T emperature: up to 125°C • Withstan ds +175°C • Few External Components Application • Tire Pressure Mo nitoring (TPM) 1. D ...

  • Atmel ATA5283 - page 2

    2 4598H–AUTO–03/07 ATA5283 2. Pin Configuration Figure 2-1. Pinning TSSOP8 L VDD 3 4 2 1 N_DATA N_WAKEUP RESET COIL 8 7 6 5 TST2 TST1 VSS Figure 2-2. Pin Description Pin Symbol Functi on 1 COIL Antenna coil input 2 TST1 T est pin (reserved) 3 TST2 T est pin (reserved) 4 VSS Signal ground 5 RESET Externa l reset input 6 N_D A T A Data signal 7 N ...

  • Atmel ATA5283 - page 3

    3 4598H–AUTO–03/07 ATA5283 3. Functional Description The ATA5283 is an ultra-low pow er ASK receiver. Without a carr ier signal it operates in the standby listen mode. In this mode it monitors th e coil input with a very low current consu mption. To activate t he IC and the connected con trol unit, the transmit ting stage must send t he preambl ...

  • Atmel ATA5283 - page 4

    4 4598H–AUTO–03/07 ATA5283 3.3 A utomatic Gain Control For a correct demodulation the signal conditione r needs appropriate interna l signal amplitude. To control the in put signal the ATA52 83 has a build in dig ital AGC. The gain control circuit regu- lates the internal signal amplitude to the reference value (Ref2, Figure 3-2 ). It de crease ...

  • Atmel ATA5283 - page 5

    5 4598H–AUTO–03/07 ATA5283 3.4 Signal Conditioner The signal conditioner d emodulates the amplifier outp ut signal and conver ts it to a binary signal. It compares the carrier signa l with the 50% reference level (see Ref 1 in Figure 3-3 ) and delivers a logical 1, if the carrier signal stays below th e reference and a logical 0, if it exc eeds ...

  • Atmel ATA5283 - page 6

    6 4598H–AUTO–03/07 ATA5283 Figure 3-5. Turn Off Delay Time (t off ) versus Antenna Q- Factor 3.5 Data Output The data output N_DATA outputs the demodulated and digitized LF signal according to the envelope of the ante nna input signal. In the standby mode the N_DATA ou tput is disabled and set to level 1. It is enabled by t he wake-up si gnal a ...

  • Atmel ATA5283 - page 7

    7 4598H–AUTO–03/07 ATA5283 3.8 Standb y Listen Mode In the standby listen mode the IC monitors the co il input with a very low current consumption. The automatic gain control is switched off and the gain is set to the maximum value. The N_DATA and the N_WAKEUP outp ut are set to a high level. Before the controller enters its standby mode after ...

  • Atmel ATA5283 - page 8

    8 4598H–AUTO–03/07 ATA5283 Figure 3-7. Pin Connection an d Pin Protection Figure 3-8. Coil Input Impe dance 2 k Ω Divider impedance 143 k Ω to 5 M Ω 2 k Ω 7 VDD VDD N_W AKEUP N_D A T A RESET VDD TST1 TST2 VSS COIL_X 6 VDD A T A5283 VDD VDD 1 k Ω VDD 5 8 2 3 4 1 1 100 1000 10000 10 10000 1000 100 Coil Input Signal (mV pp ) Z (k Ω ) m ...

  • Atmel ATA5283 - page 9

    9 4598H–AUTO–03/07 ATA5283 4. Absolute Maxim um Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause per manent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions bey ond t hose indicated in the operational sectio ns of this specification is n ...

  • Atmel ATA5283 - page 10

    10 4598H–AUTO–03/07 ATA5283 7. Electrical Characteristics V SS = 0V , V DD = 2V to 3.8V , T amb = –40 ° C to +105°C, characterized up to 125°C , unless other specified No. Parameter s T est Conditions Pin Symbol Min. T yp. Max. Unit T ype* 1 P ower Supply and Coil Limiter 1.1 P ower supply 8 V DD 23 . 23 . 8 V A 1.2 Reset supply current ? ...

  • Atmel ATA5283 - page 11

    11 4598H–AUTO–03/07 ATA5283 3 Automatic Gain Control 3.1 Preamble detection time V IN ≥ 3m V rms at 125 kHz t DAGC 19 2 P er iods B 3.2 AGC adjustment time f = 125 kHz V IN = 1 mV rms V IN = 3 mV rms V IN = 30 mV rms V IN = 100 mV rms V IN = 1V rms t AGC t AGC t AGC t AGC t AGC 0 48 220 292 450 512 P er iods C 3.3 Signal change rate (gap dete ...

  • Atmel ATA5283 - page 12

    12 4598H–AUTO–03/07 ATA5283 9. P acka g e Inf ormation 8. Or dering Information Extended T ype Number P acka ge Remarks A T A5283P-6AQJ TSSOP8L 5000 pieces, taped and reeled, Pb-free A T A5283P-6APJ TSSOP8L 500 pieces, taped and reeled, Pb-free 3 ±0.1 0.85 ±0.05 0.1 ±0.05 specifications according to DIN technical drawings Issue: 2; 15.03.04 ...

  • Atmel ATA5283 - page 13

    13 4598H–AUTO–03/07 ATA5283 10. Revision History Please note that the follo wing page numbers referred to in this section re f er to the specific revision mentioned, not to this document. Revision No. History 4598H-A UT O-03/07 • Number 5.2.1 in section 7 “Electr ical Character istics” on page 11 added 4598G-A UTO-01/07 • Put datasheet ...

  • Atmel ATA5283 - page 14

    Disclaimer: The information in this d ocument is provided in conn ection with Atmel products. No license, ex press or impli ed, by estoppel or otherwise, to any intellectual proper ty r ight is granted by this document or in connection with the sale of Atm el products. EXCEPT AS SET FORTH IN A TMEL ’S TERMS AND CONDI- TIONS OF SALE LOCA TED ON A ...

Manufacturer Atmel Category Computer Hardware

Documents that we receive from a manufacturer of a Atmel ATA5283 can be divided into several groups. They are, among others:
- Atmel technical drawings
- ATA5283 manuals
- Atmel product data sheets
- information booklets
- or energy labels Atmel ATA5283
All of them are important, but the most important information from the point of view of use of the device are in the user manual Atmel ATA5283.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Atmel ATA5283, service manual, brief instructions and user manuals Atmel ATA5283. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Atmel ATA5283.

Similar manuals

A complete manual for the device Atmel ATA5283, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Atmel ATA5283 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Atmel ATA5283.

A complete Atmel manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Atmel ATA5283 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Atmel ATA5283, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Atmel ATA5283, that we can find in the current document
3. Tips how to use the basic functions of the device Atmel ATA5283 - which should help us in our first steps of using Atmel ATA5283
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Atmel ATA5283
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Atmel ATA5283 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Atmel ATA5283?

Use the form below

If you did not solve your problem by using a manual Atmel ATA5283, ask a question using the form below. If a user had a similar problem with Atmel ATA5283 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)