English dropdown-ico

Manual Envision LM914

28 pages 0.5 mb
Download

Go to site of 28

Summary
  • Envision LM914 - page 1

    LM914 LM914 19” LCD Monitor User’s Manual By Envision Peripher als, In c. www.aocm onitor. com ...

  • Envision LM914 - page 2

    LM914 1 Before oper ating the moni tor, ple ase read this m anual thor oughly . T his manual should be r etained for fut ure ref erence. FCC Clas s B R ad io Frequ en cy Interf eren ce Statemen t WA RNING: (FOR FCC CERTIFIE D M ODELS) NOTE: Th is equipme nt has been tested and found to comply with the limits for a Class B digi tal device, pursua nt ...

  • Envision LM914 - page 3

    LM914 2 ! Do not use the monitor near w ater, e.g. near a bathtub, w ashbowl, kitchen sink, laundry tub, sw imming pool or in a w et basement. ! Do not place the monitor on an unstabl e cart, stand, or table. If the monitor falls, it can injur e a person and cause serious damage to the appliance. Use only a cart or stand recommend ed by the manufac ...

  • Envision LM914 - page 4

    LM914 3 • Sav e the original shippin g c arton and packing materials, as they wil l come in handy i f you ev er have to ship you r monitor. • For maximu m protection, re package your monit or as it was originall y packed at the factory . • To keep the monitor looking new, periodically clean it w ith a soft cloth. Stubbor n stains may be remov ...

  • Envision LM914 - page 5

    LM914 4 The follow ing symptoms are norm al wi th LCD monitor and do not indicate a problem. NOT ES • Due to the nature of the fluorescent light, the screen may fli cker during initial use. T urn o ff the Pow er Sw itch and then turn it on again to make sure the flicker disappears. • You m ay find sli ghtly un even bright nes s on the scree n d ...

  • Envision LM914 - page 6

    LM914 5 INSTA LLA TION INSTRUCTIONS SWIVEL BA SE Install Remove Figure 1 Install ing and Remov i ng the Swiv el Base POWERCORD Pow er So urce: 1. M ake sure that the pow er cord is the correct ty pe require d in your ar ea. 2. Th is LCD monito r has an Ex ternal univ ersal power supply that allo ws operation i n either 100/120 V AC or 220/240V AC v ...

  • Envision LM914 - page 7

    LM914 6 PREPA RING TO INST A L L T H E CA B L ES 1. Remove the w all mounting hole cover. 2. Remove the cable cov er. INST A L LATION S INST RU CT IONS ( cont ) INSTA LLA T IONS INSTRUCTIONS (cont) ...

  • Envision LM914 - page 8

    LM914 7 CA BLE CONNEC T IONS 1 – Connect the DC -jack pow er cable into DC -IN connector on the back of the monito r. 2. Connect one en d of the 15-pin D -Sub cable to the back of the monitor and connect the other end to the c omputer’s D- Sub port . 3. (Opti onal – Requir es a vi deo card w ith DVI port) Connect one e nd of the 24-pin DV I c ...

  • Envision LM914 - page 9

    LM914 8 Pre pa r ing T o Instal l The Optional Wall Mount A rm (Not Included) CONNECTIONS This monitor can be attached to a w all mounting arm or br acket you can purchase separately from Ergotron (w ww .ergotron.com ). T urn t he pow er OFF then dis-connect the cables from the monitor before perfo rming the procedure below . Lay the monitor face d ...

  • Envision LM914 - page 10

    LM914 9 A ttaching The Optiona l Wa ll Mount A rm (not suppl ied) Follow thes e steps to finish instal ling the w all mounting arm: 1. Place the wall mount ing arm onto the back of the monitor. Line up the holes of the ar m wi th the holes in the back of the moni tor. 2. Insert the 4 screws into the holes and tighten. 3. Reconnect the cables. Re fe ...

  • Envision LM914 - page 11

    LM914 10 • For optimal view ing it is recommended to look at the full f ace of the monitor, the n adjust the monitor’s angle to your ow n preference. • Hold the stand so you do not topple the monitor w hen you change the monitor’s angl e. • You are a ble to adjust the monito r’s angle from - 5 ° to 20 ° . Figure 3 NOT ES • Do not to ...

  • Envision LM914 - page 12

    LM914 11 OPERA TING INSTR UCTIONS Press the pow er button to turn the monitor on or off. Th e other control buttons are located on the side of the mo nitor (S ee Figure 4) . By changi ng these settings, the pictur e can be adjusted to y our personal pr eferences. • The pow er cord should be connected. • Connect the v ideo cable from the moni to ...

  • Envision LM914 - page 13

    LM914 12 FRONT PA NEL CONTROL • Pow er Button : Press this button t o switch the mo nitor’s pow er ON or OFF. • MENU / ENTER : Activate O SD menu w hen OSD is OFF or activate /de-activate adjustment function w hen O SD is ON or E xit O SD menu w hen in B rightness/Contrast OSD status. • Brightness / : Adjust bright nes s or function adjust. ...

  • Envision LM914 - page 14

    LM914 13 1. Press the M ENU-but ton to activate the OSD window . See figure 5. 2. Press or to select the desired function. See figure 5. 3. Press the M ENU-but ton again to activate the hig hlighted function. 4. Press or to adjust the selected function. Note: is used to adjust the function down & is used to ad just the function up. This is due ...

  • Envision LM914 - page 15

    LM914 14 Below desc ribes the function of each OS D icon. 1. Contra st Adjust the picture contrast. 2. Brightness Adjust the picture brightness. 3. Input Selected Input Signal source selected ( select Analog or Digital input s ource ) 4. Focus Adjust pictur e Focus (available in Analog mode only) . 5. Clo ck Adjust picture C lock (av ailable in An ...

  • Envision LM914 - page 16

    LM914 15 Plug & Pla y D DC1/2B Featur e This monitor is equipped with VESA DDC1/ 2B capabilities acc ording to the VESA DDC STA NDARD. It allow s the mon itor to inform the h ost system of its identity and, dependi ng on the lev el of DDC us ed, communicate additi onal information about its display capabilities. T he communication channel is de ...

  • Envision LM914 - page 17

    LM914 16 TECHNIC A L SUPPORT (FA Q) Problem & Question Possible Solution Pow er LED is not on *Check if the Power Switch is in the ON position *Pow er Cord s hould be connected No Plug & P lay *Check if the PC s ystem is Plug & Play compatib le *Check if the Vi deo Card is P lug & Play compatib le *Check if the D -15 plug pin of Vid ...

  • Envision LM914 - page 18

    LM914 17 Screen image i s not centered or sized properl y. *Adjust pix el frequency ( CLOCK) and FOCU S or press hot-key (AUTO) Picture has color defects (w hite does not look w hite) *Adjust RG B color or sele ct a pre-set color temperature fr om OSD. Horizo ntal or v ertical disturbances on the screen *Use wi n 95/98 shut-dow n mode Adjust CLOC K ...

  • Envision LM914 - page 19

    LM914 18 NO SIGNA L 1. Check that the signal- cable is properly connected , If the connector is loose, tighten the connector’ s screws. 2. Check the signal-cable’ s connection pins for damage. INP UT NOT SU PPOR T Your computer has been set to unsuitabl e display mode ,set the compute r to display mode given in the following t able. UNSUP PORT ...

  • Envision LM914 - page 20

    LM914 19 1024 × 768 70Hz 1024 × 768 75Hz 1024 × 768 85Hz 1280 × 1024 60Hz 1280 × 1024 75Hz 1280 × 1024 85Hz 1152 × 864 75Hz 1280 × 960 60Hz 1280 × 960 85Hz 640 × 480 67Hz 832 × 624 75Hz 640 × 400 56Hz NOTE: For digital input, the r esolution 1280 x 1024 @ 85Hz and 1280 x 9 60 @ 85Hz are not supp orted ...

  • Envision LM914 - page 21

    LM914 20 FOR FI RST TIM E INS T A LL : This is a Plug & Play LCD monitor. Turn off the PC then connect the cables. Pow er on the PC and it w ill automatically detect y our new monit or. The W indow s Operating system w ill automatically install a plug & pl ay driv er for it. If y ou would still like to install the dr iver i ncluded in the d ...

  • Envision LM914 - page 22

    LM914 21 A PPENDIX SPECIF ICA TIO NS Driving system TFT Color LCD LCD Pan el Siz e 48cm(19.0") Pix el pitch 0.294mm( H ) x 0.294mm( V ) View able angle 170 ° (H) 17 0 ° (V ) Response time 25 ms ( T ypical ) Video R,G,B A nalog Interface Input Separ ate Sy nc. H/V TT L H-Frequency 31KHz – 92KHz V-Freque ncy 55-85Hz Displa y Colors 16.7M Col ...

  • Envision LM914 - page 23

    LM914 22 Switc h • Au t o Adj us t Key • / Brightness • / Contrast • Powe r Butt on • ME NU / Exi t • Vol ume Ex ternal Controls: Functions • Contras t • Brightness • Input Selected • Focus • Clock • H-P osition • V-Po siti on • Auto-center • Language • Scaling Mode • C1 ( 6500 ° K ) • C2 ( 7800 ° K ) • RGB C ...

  • Envision LM914 - page 24

    LM914 23 STANDA RD RESOLUT ION HORIZONT AL FREQUEN CY VERTICA L FREQUENCY Dos-mode 640 × 400 31.47kHz 70.0Hz Dos-mode 720 x 400 31.47kHz 70.0Hz Dos-mode 720 x 400 31.47kHz 70.0Hz VGA 640 × 480 31.47kHz 60.0Hz 640 × 480 35.00kHz 66.6Hz 640 × 480 37.50kHz 75.0Hz 640 × 480 37.86kHz 72.0Hz 800 × 600 37.879kHz 60.0Hz SVGA 800 × 600 46.875kHz 75.0 ...

  • Envision LM914 - page 25

    LM914 24 15 6 10 11 15 15 - Pin Co lor Display Signal C able PIN NO. DESCRIPT ION PI N NO. DESCRIPT ION 1. Red 9. +5V 2. Green 10. Detect Cable 3. Blue 11. NC 4. Ground 12. DDC-Serial Data 5. Ground 13. H-Sy nc 6. R-G round 14. V-Sy nc 7. G-G r ound 15. DDC-Seria l Cloc k 8. B-Gr ound 24 - Pin Co lor Display Signal C able PIN NO. DESCRIPT ION PI N ...

  • Envision LM914 - page 26

    LM914 25 8. N.C. 20. TMDS Data 5- 9. TM DS Data 1- 21. TM DS Data 5+ 10. TM DS Data 1+ 22. TM DS Clock Shield 11. TM DS Data 1/3 Shie ld 23. TM DS Cl ock + 12. TM DS Data 3- 24. TM DS Cl ock - ...

  • Envision LM914 - page 27

    LM914 26 W AR R AN T Y S T AT E M E N T for AOC Color Monitors Including t hose Sold w ithin N orth America a s Specified Env ision Peripherals, Inc. warrants this product to be fr ee from defects in material and w orkmanship for a period of thre e (3) y ears after the original date of consumer purchase. During this period, E PI (EP I is the abb re ...

  • Envision LM914 - page 28

    LM914 27 This three-y ear limited war ranty does not cover any of the pr oduct's firmw are or hardw are that you or any third par ty have modified or alte red; you bear the sole responsibility and liability for any such modifi cation or alteration. ALL EXPRESS AND IMPLIED W ARRANTIES FOR THIS PRODUCT (INCLUDING T HE W ARRANTIES OF M ERCHANT AB ...

Manufacturer Envision Category Computer Monitor

Documents that we receive from a manufacturer of a Envision LM914 can be divided into several groups. They are, among others:
- Envision technical drawings
- LM914 manuals
- Envision product data sheets
- information booklets
- or energy labels Envision LM914
All of them are important, but the most important information from the point of view of use of the device are in the user manual Envision LM914.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Envision LM914, service manual, brief instructions and user manuals Envision LM914. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Envision LM914.

Similar manuals

A complete manual for the device Envision LM914, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Envision LM914 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Envision LM914.

A complete Envision manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Envision LM914 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Envision LM914, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Envision LM914, that we can find in the current document
3. Tips how to use the basic functions of the device Envision LM914 - which should help us in our first steps of using Envision LM914
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Envision LM914
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Envision LM914 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Envision LM914?

Use the form below

If you did not solve your problem by using a manual Envision LM914, ask a question using the form below. If a user had a similar problem with Envision LM914 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)