English dropdown-ico

Manual Humminbird HDR200

14 pages 1.74 mb
Download

Go to site of 14

Summary
  • Humminbird HDR200 - page 1

    ...

  • Humminbird HDR200 - page 2

    TRANSDUCER MOUNTING PROCEDURE Humminbird’s high - speed transducer is supplied with your LCR. This transducer has been designed to give good high speed readings on most all boat designs, including aluminum. Please carefull y consider the following before installing your transducer. TRANSDUCER MOUNTING OPTIONS A. Transom Mount - The Humminbird hig ...

  • Humminbird HDR200 - page 3

    by rotating up out of the metal spring bracket without harming the transducer, or your boat. The transducer can be re - engaged by simply rotating the transducer down and snapping it back in place. (See Figure A) B. Inside Hull Mount - The high speed transducer can be mounted inside the hull (without pivot assembly) using the proper two - part epox ...

  • Humminbird HDR200 - page 4

    Once the location is determined mark and drill three 7/64” dia.. holes noted on the template. Attach the metal bracket using three #10 self threading screws supplied. Be sure to align holes in the center of the Bracket sl ots. On some aluminum boats it may be necessary to use a wood back - up plate. It is important to use a silicone sealant betwe ...

  • Humminbird HDR200 - page 5

    NOTE: On boats with more than 15 degree deadrise angle it may be necessary to mount the transducer slightly off parallel with the water lev el. (See Figure E) Mark and drill the three 9/64” dia. holes as shown on the template. Attach the metal bracket using the three #10 self threading screws supplied. Be sure to align the holes so that they are ...

  • Humminbird HDR200 - page 6

    Step 4 TRANSDUCER ASSEMBLY - Insert the transducer assembly into the metal bracket from the bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket. Slide the O - ring on to the h eaded pin and insert it through the two parts. Assemble by screwing the ¼”x3/8” allen head screw into the end of the pin a ...

  • Humminbird HDR200 - page 7

    wrench provided. The screws are visible through the access holes on each side of the metal bracket. Check to make sure the transducer main body is rigidly faste ned to the pivot. (See Figure H) Step 6 CHECK POSITION OF TRANSDUCER - At this point, check to see that the bottom of the transducer is a minimum of ¼” below the bottom of the transom. ( ...

  • Humminbird HDR200 - page 8

    7. Remove the water and transducer and clean the m arked area and the bottom of the transducer thoroughly. 8. Using the Humminbird Epoxy Kit or equivalent, mix an ample amount of epoxy without causing it to bubble and pour it in the area the transducer is to be mounted. The puddle should be larger than the bo ttom of the transducer. 9. Coat the bot ...

  • Humminbird HDR200 - page 9

    Install the mounting knobs and tighten snugly. The unit can now be swiveled and tilte d to any desired position. ...

  • Humminbird HDR200 - page 10

    OTHER MOUNTING OPTIONS 1. The LCR gimbal bracket can also be mounted on the SM - 4, quick disconnect swivel mount. 2. The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount, however, this method is not recommended since the unit cannot be rotated. INSTALLING THE CABLES Your LCR comes equipped with Humminbird’s n ...

  • Humminbird HDR200 - page 11

    It plugs into the outlet on the back of the unit marked “Power”. The transducer connector is identified with the letter T and plugs into the outlet on the back of the unit marked “Transducer”. Note: An adapter (AD - 4) is available to allow use of an old waterproof (BNC) transducer with the LCR, but be sure that the transducer is a 16degree ...

  • Humminbird HDR200 - page 12

    Installing the HDR 200 Before mounting the HDR 200, gather the parts you need: HDR 200, mounting hardware kit, and transducer cable. If the transducer cable is no t long enough for your installation, see “Accessories” earlier in this manula for information on the EC - 6 10’ extension. • The mounting surface should be adequately supported to ...

  • Humminbird HDR200 - page 13

    begin transmitting, and automatically display the digital depth. (If the HDR 200 is wired to a switch other than the ignition switch, turn that switch on.) Increase your boat speed to ensure that you get a continuous bottom reading as the boat moves. Your HDR 200 and its transducer are designed to operate at up to 75 mph. However, use caution when ...

  • Humminbird HDR200 - page 14

    Do not attempt to repair HDR 200 yourself. Repairs should be performed only by authorized Humminbird technicians. ...

Manufacturer Humminbird Category SONAR

Documents that we receive from a manufacturer of a Humminbird HDR200 can be divided into several groups. They are, among others:
- Humminbird technical drawings
- HDR200 manuals
- Humminbird product data sheets
- information booklets
- or energy labels Humminbird HDR200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Humminbird HDR200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Humminbird HDR200, service manual, brief instructions and user manuals Humminbird HDR200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Humminbird HDR200.

Similar manuals

A complete manual for the device Humminbird HDR200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Humminbird HDR200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Humminbird HDR200.

A complete Humminbird manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Humminbird HDR200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Humminbird HDR200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Humminbird HDR200, that we can find in the current document
3. Tips how to use the basic functions of the device Humminbird HDR200 - which should help us in our first steps of using Humminbird HDR200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Humminbird HDR200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Humminbird HDR200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Humminbird HDR200?

Use the form below

If you did not solve your problem by using a manual Humminbird HDR200, ask a question using the form below. If a user had a similar problem with Humminbird HDR200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)