English dropdown-ico

Manual Kenwood KRC-4904

26 pages 0.99 mb
Download

Go to site of 26

Summary
  • Kenwood KRC-4904 - page 1

    KRC-4904 © B64-2392-00/00 (E2N) CASSETTE RECEIVER INSTRUCTION MANUAL KRC-4904(E-W)_U.S r1 02.9.26 6:20 PM Page iii ...

  • Kenwood KRC-4904 - page 2

    — 2 — English Contents Safety precautions ......................3 About Cassette tape ...................4 General features .........................5 Power Selecting the Source V olume Attenuator Loudness System Q Audio Control Speaker Setting Switching Display Theft Deterrent Faceplate TEL Mute T uner features .............................9 T ...

  • Kenwood KRC-4904 - page 3

    — 3 — To prevent injury and/or fire, take the following precautions: • Insert the unit all the way until it is fully locked in place. Otherwise it may fly out of place during collisions and other jolts. • When extending the ignition, battery or ground wires, make sure to use automotive- grade wires or other wires with an area of 0.75mm 2 (A ...

  • Kenwood KRC-4904 - page 4

    — 4 — English • If you experience problems during installation, consult your Kenwood dealer . • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer . •P ress the reset button if the Disc auto changer fails to operate correctly . Normal operatin ...

  • Kenwood KRC-4904 - page 5

    Press the [SRC] button. Source required Display T uner "TUNER" T ape "T APE" External disc "DISC"/"CD" Standby (Illumination only mode) "ALL OFF" This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicles battery . The time until full power OFF ...

  • Kenwood KRC-4904 - page 6

    1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below . 4 Adjust the Audio item Press the [ 4 ] or [ ¢ ] button. Aud ...

  • Kenwood KRC-4904 - page 7

    Fine-tuning so that the System Q value is optimal when setting the speaker type. 1 Enter Standby Press the [SRC] button. Select the "ALL OFF" display . 2 Enter Speaker Setting mode Press the [Q] button. 3 Select the Speaker type Press the [ 4 ] or [ ¢ ] button. Each time the button is pressed the setting switches as shown below . Speaker ...

  • Kenwood KRC-4904 - page 8

    The audio system automatically mutes when a call comes in. When a call comes in "CALL" is displayed. The audio system pauses. Listening to the audio during a call Press the [SRC] button. The "CALL" display disappears and the audio system comes back ON. When the call ends Hang up the phone. The "CALL" display disappears ...

  • Kenwood KRC-4904 - page 9

    Selecting the station. 1 Select tuner source Press the [SRC] button. Select the "TUNER" display . 2 Select the band Press the [FM] or [AM] button. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. Frequency range - FM1: 65.0 MHz — 74.0MHz - FM2, 3: 87.5 MHz — 108.0MHz 3 T une up or down band Press t ...

  • Kenwood KRC-4904 - page 10

    Calling up the stations in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Call up the station Press the [#1] — [#6] button. Preset T uning Putting stations with good reception in the memory automatically . 1 Select the band for Auto Memory Entry Press the [FM] or [AM] button. 2 Open Auto Memory Entry Press the [AME] button for at ...

  • Kenwood KRC-4904 - page 11

    Skipping to the next song or the start of the current song. Skipping to the next song Press the [ ¢ ] button. Skips to the start of the current song Press the [ 4 ] button. T ape Advance Fast Forwarding Press the [FM] button. When it's stopped press the [ 23 ] button. Rewinding Press the [AM] button. When it's stopped press the [ 23 ] bu ...

  • Kenwood KRC-4904 - page 12

    External disc control features Repeating the present song. Press the [REP] button. Each time the button is pressed the Music Repeat turns ON or OFF . When it's ON, "REP ON" is displayed. Music Repeat Switching to the radio automatically during Fast Forwarding and Rewinding. Press the [T .CALL] button. Each time the button is pressed ...

  • Kenwood KRC-4904 - page 13

    Replaying the track/disc you're listening to. Press the [REP] button. Each time the button is pressed the Repeat Play switches as shown below . Repeat play Display T rack Repeat "TREP ON"/"REP ON" Album Repeat (Function of disc changer) "DREP ON" OFF "REP OFF" T rack/Album Repeat Selecting the disc you w ...

  • Kenwood KRC-4904 - page 14

    Attaching a title to a CD. 1 Play the disc you want to attach a name to A title can't be attached to a MD. 2 Enter Menu mode Press the [MENU] button for at least 1 second. "MENU" is displayed. 3 Select Name set mode Press the [FM] or [AM] button. Select the "NAME SET" display . 4 Enter Name set mode Press the [ 4 ] or [ ¢ ...

  • Kenwood KRC-4904 - page 15

    Menu system Scrolling the displayed CD text or MD title. Press the [SCRL] button. T ext/T itle Scroll — 15 — AM 4¢ FM MENU Menu display KRC-4904(E-W)_U.S r1 02.9.26 6:20 PM Page 15 ...

  • Kenwood KRC-4904 - page 16

    A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display Setting "DSI ON" LED flashes. "DSI OFF" LED OFF . DSI (Disabled System Indicator) 1 Select Clock Adjustment mode Press the [FM] or [AM] button. Select the "CLK ADJ" display . 2 Enter Clock Adjust mode Press the [ 4 ...

  • Kenwood KRC-4904 - page 17

    Setting the timer to turn this unit's power OFF automatically when Standby mode continues. Using this setting can save the vehicle's battery power . Display Setting "OFF – – –" Power OFF T imer function is OFF . "OFF 20M" T urns the power OFF after 20 minutes. (Original setting) "OFF 40M" T urns the pow ...

  • Kenwood KRC-4904 - page 18

    English — 18 — — 18 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. ..........................................1 ..........................................2 ..........................................1 1 2 3 External view Nu ...

  • Kenwood KRC-4904 - page 19

    — 19 — – + + + + + FRONT • L FRONT • R REAR • L REAR • R P.CONT ANT. CONT — 19 — 9 Rear right output (Red) 8 Rear left output (White) KENWOOD disc changer input 25 FM/AM antenna input 10 To connect the Disc changer , consult your Disc changer manual. 26 Wiring harness (Accessory 1 ) 13 TEL mute terminal 28 Fuse (10A) 23 Plug (page ...

  • Kenwood KRC-4904 - page 20

    English — 20 — — 20 — Connecting Wires to T erminals ■ Connector Function Guide 10 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Connector A Connector B Pin Numbers Plug Functions for ISO Connectors setting* <External Power Connector> A–4 1 Battery 2 Ignition (ACC) A–5 Power Control A–7 1 Ignition (ACC) 2 Battery A–8 Earth (Ground) Connec ...

  • Kenwood KRC-4904 - page 21

    — 21 — — 21 — ■ Power Control T erminal Connections Power Control terminal (Flat terminal) 4 Power Amplifier 6 The output of the Power Control terminal is switched along with the power on/off switching of the unit. This terminal can be connected to the P .CON (REMOTE) terminal of the amplifier , or used as the power supply of the special ...

  • Kenwood KRC-4904 - page 22

    English — 22 — — 22 — ■ Removing the hard rubber frame 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner . Catch Lock 1 Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the fi ...

  • Kenwood KRC-4904 - page 23

    — 23 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. 01 ✔ The fuse has blown. ☞ After checking for short circuits in the wires, replace the fuse with one with the ...

  • Kenwood KRC-4904 - page 24

    English — 24 — Cassette tape source ? Can’ t remove tape. 44 ✔ The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF . ☞ The tape can only be removed within 10 minutes of the ACC switch being turned OFF . If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. ...

  • Kenwood KRC-4904 - page 25

    — 25 — The following messages are displayed when your system condition. EJECT : No disc magazine has been loaded in the changer . The disc magazine is not completely loaded. E01 ➪ Load the disc magazine properly . No CD in the unit. ➪ Insert the CD. NO DISC: No disc has been loaded in the disc magazine. E02 ➪ Load a disc into the disc mag ...

  • Kenwood KRC-4904 - page 26

    English — 26 — Specifications FM tuner section Frequency range FM1.......................................................65.0 MHz – 74.0 MHz FM2, 3.................................................87.5 MHz – 108.0 MHz Frequency step FM1 ..............................................................................30 kHz FM2, 3 .............. ...

Manufacturer Kenwood Category Cassette Player

Documents that we receive from a manufacturer of a Kenwood KRC-4904 can be divided into several groups. They are, among others:
- Kenwood technical drawings
- KRC-4904 manuals
- Kenwood product data sheets
- information booklets
- or energy labels Kenwood KRC-4904
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenwood KRC-4904.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenwood KRC-4904, service manual, brief instructions and user manuals Kenwood KRC-4904. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenwood KRC-4904.

Similar manuals

A complete manual for the device Kenwood KRC-4904, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenwood KRC-4904 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenwood KRC-4904.

A complete Kenwood manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenwood KRC-4904 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenwood KRC-4904, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenwood KRC-4904, that we can find in the current document
3. Tips how to use the basic functions of the device Kenwood KRC-4904 - which should help us in our first steps of using Kenwood KRC-4904
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenwood KRC-4904
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenwood KRC-4904 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenwood KRC-4904?

Use the form below

If you did not solve your problem by using a manual Kenwood KRC-4904, ask a question using the form below. If a user had a similar problem with Kenwood KRC-4904 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)