English dropdown-ico

Manual Kohler KT6908

20 pages 0.18 mb
Download

Go to site of 20

Summary
  • Kohler KT6908 - page 1

    Installation Guide Single-Control Bath and Shower T rim M product numbers ar e for Mexico (i.e. K-12345 M ) Los números de pr oductos seguidos de M corresponden a México (Ej. K-12345 M ) Français, page“ Français-1” Español, página“ Español-1” K-T6908 K-T6910 K-T6913 1 14487-2-CC ...

  • Kohler KT6908 - page 2

    T ools and Materials Before Y ou Begin CAUTION: Risk of product damage. Long screws, for installing trim, can damage the K-2971-KS valve. When using this valve and trim in a fiberglass or acrylic installation, use the 88526 Thin W all Installation Kit. Observe all local plumbing and building codes. The finished wall or bath/shower unit must be in ...

  • Kohler KT6908 - page 3

    1. Install the Spout Remove the temporary nipple. Apply thread sealant and install a 1/2 ″ nipple so it extends 7/16 ″ (1.1 cm) beyond the finished wall. Apply a bead of plumbers putty or other sealant around the inlet end of the spout according to the manufactur er’s instructions. Apply thread sealant to the nipple and thr ead the spout ont ...

  • Kohler KT6908 - page 4

    2. Install the Showerhead NOTICE: Do not use thread sealant compound (pipe dope) on the shower arm threads. Instead, use thr ead sealant tape on the shower arm threads. This will avoid clogging the shower head spray outlets. Remove the temporary nipple from the shower elbow . Apply a bead of plumbers putty or other sealant to the back of the escutc ...

  • Kohler KT6908 - page 5

    3. W ater T emperature Adjustment CAUTION: Risk of personal injury . T o eliminate the risk of scalding, the water temperature should never be set above 120°F (49°C). NOTE: Do not remove the O-ring and collar at this time. Removing the O-ring and collar will change the factory setting for the maximum water temperature. T urn the valve clockwise t ...

  • Kohler KT6908 - page 6

    4. Install the Faceplate and Handle Remove and discard the plaster guar d and/or dome, if installed. Rotate the valve stem fully counterclockwise to the ″ OFF ″ position. Install the faceplate onto the valve so the notch is to the bottom and secure with scr ews. Do not overtighten the screws. Install the graphics ring to the faceplate, and rota ...

  • Kohler KT6908 - page 7

    Guide d’installation Baignoire mono-contrôle et garniture de douche Outils et matériels A vant de commencer A TTENTION: Risque d’endommagement du produit. Les vis longues, pour l’installation de la garniture, peuvent endommager la valve K-2971-KS. Lorsque cette valve et la garniture sont utilisées dans une installation en fibr es de verre ...

  • Kohler KT6908 - page 8

    1. Installer le bec Retirer le mamelon temporair e. Appliquer un ruban d’étanchéité pour filetage et installer un mamelon de 1/2 ″ de manière à ce qu’il s’étende de 7/16 ″ (1.1 cm) au-delà du mur fini. Appliquer du mastic d’étanchéité ou un produit semblable sur le périmètre de l’extrémité arrièr e du bec, selon les i ...

  • Kohler KT6908 - page 9

    2. Installer la pomme de douche A VIS: Ne pas utiliser de joint d’étanchéité pour filetage (colle à tuyau) sur les filetages de bras de douche. Utiliser du ruban d’étanchéité pour filetage sur les filetages de bras de douche à la place. Ceci évitera de boucher les orifices de vaporisateur la pomme de douche. Retirer le mamelon tem ...

  • Kohler KT6908 - page 10

    3. Réglage de la température d’eau A TTENTION: Risque de blessures corporelles. Pour éliminer les risques de brûlures, la températur e ne devrait pas être réglée au-dessus de 120°F (49°C). REMARQUE: Ne pas retir er le joint torique ou le collier pour le moment. Retirer le joint torique changerait le réglage d’usine de la température ...

  • Kohler KT6908 - page 11

    4. Installer le couvercle et la poignée Retirer et jeter le r enfort en plâtre et/ou dôme, s’il est installé. Pivoter la tige de la valve complètement vers la gauche à la position fermée ″ OFF ″ . Installer le couvercle sur la valve de manièr e à ce que l’encoche soit à la base et sécuriser avec des vis. Ne pas trop serr er les v ...

  • Kohler KT6908 - page 12

    Guía de instalación Guarnición de grifería monomando de bañera y ducha Herramientas y materiales Antes de comenzar PRECAUCIÓN: Riesgo de daños al producto. Los tornillos largos, para instalar la guarnición, pueden dañar la válvula K-2971-KS. Al emplear esta válvula y guarnición en una instalación de fibra de vidrio o acrílica, utilic ...

  • Kohler KT6908 - page 13

    1. Instale el surtidor Retire el niple pr ovisional. Aplique sellador de roscas e instale un niple de 1/2 ″ de modo que sobresalga 7/16 ″ (1,1 cm) de la par ed acabada. Aplique masilla de plomería u otro sellador alr ededor del extremo de entrada del surtidor , según las instrucciones del fabricante. Aplique sellador de roscas en el niple y e ...

  • Kohler KT6908 - page 14

    2. Instale la cabeza de ducha A VISO: No utilice compuesto sellador líquido de r oscas (pasta lubrificante) en las roscas del brazo de la ducha. En su lugar , aplique cinta selladora de roscas a las r oscas del brazo de ducha. Esto evitará que se tapen las salidas rociadoras de la cabeza de ducha. Retire el niple pr ovisional del codo de la duch ...

  • Kohler KT6908 - page 15

    3. Ajuste de la temperatura del agua PRECAUCIÓN: Riesgo de lesiones personales. Para eliminar el riesgo de quemaduras, la temperatura del agua nunca debe ajustarse a más de 120°F (49°C). NOT A: No retir e el arosello (O-ring) ni el collarín en este momento. Si quita el arosello (O-ring) y el collarín, cambiará la temperatura máxima del agua ...

  • Kohler KT6908 - page 16

    4. Instale la placa frontal y la manija Retire y deseche el pr otector de yeso y/o la cúpula, si están instalados. Gire la espiga de la válvula completamente a la izquier da, a la posición de cerrada. Instale la placa frontal sobr e la válvula, de manera que la muesca esté orientada hacia abajo, y fije con tornillos. No apriete demasiado los ...

  • Kohler KT6908 - page 17

    1 14487-2- CC ...

  • Kohler KT6908 - page 18

    1 14487-2- CC ...

  • Kohler KT6908 - page 19

    1 14487-2- CC ...

  • Kohler KT6908 - page 20

    USA/Canada: 1-800-4KOHLER México: 001-800-456-4537 kohler .com ©2010 Kohler Co. 1 14487-2-CC ...

Manufacturer Kohler Category Plumbing Product

Documents that we receive from a manufacturer of a Kohler KT6908 can be divided into several groups. They are, among others:
- Kohler technical drawings
- KT6908 manuals
- Kohler product data sheets
- information booklets
- or energy labels Kohler KT6908
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kohler KT6908.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kohler KT6908, service manual, brief instructions and user manuals Kohler KT6908. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kohler KT6908.

Similar manuals

A complete manual for the device Kohler KT6908, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kohler KT6908 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kohler KT6908.

A complete Kohler manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kohler KT6908 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kohler KT6908, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kohler KT6908, that we can find in the current document
3. Tips how to use the basic functions of the device Kohler KT6908 - which should help us in our first steps of using Kohler KT6908
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kohler KT6908
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kohler KT6908 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kohler KT6908?

Use the form below

If you did not solve your problem by using a manual Kohler KT6908, ask a question using the form below. If a user had a similar problem with Kohler KT6908 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)