-
TP-Link TD-VG3511 - page 1
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router 1910010723 Rev: 1.0.0 ...
-
TP-Link TD-VG3511 - page 2
COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other brands and product names are trademarks or registered trademarks of t heir respective holders. No part of the specific ations may be reproduced in any form or by any means or used to m ake any derivativ ...
-
TP-Link TD-VG3511 - page 3
FCC STATEMENT This equipment has been tested and found to comply wi th the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen erates, uses and can radiate radio frequency energy and, if no ...
-
TP-Link TD-VG3511 - page 4
This device has been designed to operate with the antennas listed below , and having a maximum gain of 5 dBi. Antennas not included in this list or having a gain greater t han 5 dBi are strictly prohibited for use with this device. T he required antenna impedance is 50 ohms. T o reduce potential radio interference to other users, the antenna type a ...
-
TP-Link TD-VG3511 - page 5
Safety Information z When product has power button, the powe r button is one of the way to shut off the product; When there is no power button, the only way to co mpletely shut off power is to disconnect the product or the power adapter from the power source. z Don’t disassemble the product, or make repairs yourself. You run the ri sk of electric ...
-
TP-Link TD-VG3511 - page 6
TP-LINK TECHNOLOGIES CO., L TD TP-LINK TECHNOLOGIES CO., L TD Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China DECLARA TION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N VoIP ADSL2+ Modem Router Model No.: TD-VG3511 T rademark: TP-LINK ...
-
TP-Link TD-VG3511 - page 7
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Product Overview ................................................................................... 2 1.1 Overview of the Modem Router .......................................................................... ...
-
TP-Link TD-VG3511 - page 8
4.6 Wireless ........................................................................................................................ 43 4.6.1 Basic Settings .................................................................................................................... 43 4.6.2 WPS Settings ..................................................... ...
-
TP-Link TD-VG3511 - page 9
4.12.3 WAN Host ......................................................................................................................... 85 4.12.4 Schedule ........................................................................................................................... 87 4.13 Bandwidth Control ........................................... ...
-
TP-Link TD-VG3511 - page 10
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1 Package Content s The following contents should be found in your package: ¾ One TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router ¾ One Power Adapter for TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router ¾ Quick Installation Guide ¾ One RJ45 cable ¾ Three RJ11 cables ¾ ...
-
TP-Link TD-VG3511 - page 11
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 2 Chapter 1. Product Overview Thank you for choosing the TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router . 1.1 Overview of the Modem Router The TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP. Powered by 1x1 MI ...
-
TP-Link TD-VG3511 - page 12
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 3 1.2 Main Features ¾ Four 10/100Mbps Auto-Negotia tion RJ45 LAN ports (Auto MD I/MDIX), three RJ11 ports, one USB 2.0 ports ¾ Provides external splitter. ¾ Adopts Advanced DMT modulati on and demodul ation technology. ¾ Supports bridge mode and Router func tion. ¾ Multi-user sha ...
-
TP-Link TD-VG3511 - page 13
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The Router’s LEDs are located on the front panel (V iew from left to right). They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Status Indication On The modem router is ...
-
TP-Link TD-VG3511 - page 14
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 5 Off There is no device connected to this LAN port. On A storage device or printer has connected to the USB port. Flash The modem router is sending or receiving data over this USB port. (USB) Off No storage device or printer is plugged into the USB port. On The phone is off hook. Fla ...
-
TP-Link TD-VG3511 - page 15
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 6 ¾ RESET: There are two ways to reset t he Router's factory defaults. Method one: With the Router powered on, use a pi n to press and hold the RESET butto n for at least 5 seconds. And the Router will reboot to its factory default settings. Method two: Restore the default setti ...
-
TP-Link TD-VG3511 - page 16
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 7 Chapter 2. Connecting the Modem Router 2.1 System Requirement s ¾ Broadband Internet Access Service (DSL/Cable/Ethernet). ¾ PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. ¾ TCP/IP protocol on each PC. ¾ Web browser, such as Micr osoft Internet Ex ...
-
TP-Link TD-VG3511 - page 17
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 8 2.3 Connecting the Modem Router Before installing the device, please make sure y our broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cabl e connection, cut off the power supply and keep your hands dr y. You can follow the ...
-
TP-Link TD-VG3511 - page 18
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 9 Figure 2-1 ...
-
TP-Link TD-VG3511 - page 19
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 10 Chapter 3. Quick Inst allation Guide 3.1 Configuring the PC After you directly connect your PC to the Modem RouterT D-VG3511 or connect your adapter to a Hub/Switch which has c onnected to the Modem Router, you need to configure your PC’s IP address. Follow the steps below to con ...
-
TP-Link TD-VG3511 - page 20
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 11 Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP) , and then click the Properties button. Figure 3-3 ...
-
TP-Link TD-VG3511 - page 21
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 12 Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK . Figure 3-4 ) Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server addre ss automatically” in the screen above. Now, ...
-
TP-Link TD-VG3511 - page 22
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 13 If the result displayed is similar to the screen shown belo w, it means t hat your PC has not connected to the Modem Router. Figure 3-6 You can check it follo wing the steps below: 1) Is the connection between your PC and the Modem Router correct? The LEDs of LAN port which you lin ...
-
TP-Link TD-VG3511 - page 23
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 14 Figure 3-8 ) Note: 1) Do not mix up the user name and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-br owser has been set to a proxy. Go to Tools menu → Network → LAN S ...
-
TP-Link TD-VG3511 - page 24
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 15 Figure 3-10 4. Change the VPI or VCI values which are used to define a unique path for your connection. If you have been given specific settings for this to configuration, type in the correct values assigned by your ISP. Click Next . Figure 3-11 5. Here we select PPPoE WAN Link Typ ...
-
TP-Link TD-VG3511 - page 25
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 16 Figure 3-13 7. Basic parameters of Voice can be set on the Voice screen. Please enter a profile name to identify this account and other parameters provided by yo ur ISP. If you don’t want to configure VoIP function now, leave "Pro file Name" blank and click Next to skip ...
-
TP-Link TD-VG3511 - page 26
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 17 Figure 3-15 9. You will see the Complete screen below, click Finish to complete these settings. Figure 3-16 ...
-
TP-Link TD-VG3511 - page 27
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 18 Chapter 4. Configuring the Modem Router This chapter will show each Web page's key function and the c onfiguration way. 4.1 Login After your successful login, you will see the main menu on the left of the Web-based utility. On the right, there are the corresponding explanation ...
-
TP-Link TD-VG3511 - page 28
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 19 Figure 4-1 4.3 Quick Setup Please refer to Section 3.2 Quick Installation Guide . 4.4 Network Choose “ Netw ork ”, there are many submenus under the main menu. Click any one of them, and you will be able to configur e the corresponding function. ...
-
TP-Link TD-VG3511 - page 29
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 20 4.4.1 WAN Settings Choose “ Netw ork ” Æ “ WAN Settings ”, and you will see the WAN Port Information Table in the screen similar to Figure 4-2 , which describes the WAN port setti ngs and the relevant manipulation to each interface. There are six different configurat ions ...
-
TP-Link TD-VG3511 - page 30
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 21 Figure 4-3 4.4.1.1 Static IP Select this option if your ISP prov ides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below. ...
-
TP-Link TD-VG3511 - page 31
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 22 Figure 4-4 ATM Configuration: ¾ VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. ¾ VCI (1~65535 ): Identifies the virtual c hannel endpoints in an ATM network. The valid ra ...
-
TP-Link TD-VG3511 - page 32
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 23 ¾ Subnet Mask: Enter the subnet Mask in dotted-decimal not ation pro vided by your ISP, usually is 255.255.255.0. ¾ Default Gateway (Optional): Enter the gateway IP addres s in dotted-decimal notatio n provided by your ISP. ¾ DNS Server/ Secondary DNS Server: Here you can set DN ...
-
TP-Link TD-VG3511 - page 33
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 24 Figure 4-5 Click Advanced , advanced selections for WAN Service Setup can be shown. ¾ MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not re commended that you change the default value unless ...
-
TP-Link TD-VG3511 - page 34
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 25 ¾ Enable IGMP Proxy : IGMP (Internet Group Management Protocol) is used to manage multicasting on TCP/IP networks. So me ISPs us e IGMP to perform remote configuration for client devices, such as the Modem Router. The default value is enabled, and if you are not sure, please conta ...
-
TP-Link TD-VG3511 - page 35
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 26 ¾ PPP Username/Password/Confirm Password: Enter the User Name, Password and Confirm Password provided by your ISP. These fields are case-sensitive. ¾ Authentication Method: Select the Authentication Method from the drop-down list, the default method is AUTO_AUTH , and you can lea ...
-
TP-Link TD-VG3511 - page 36
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 27 Figure 4-7 4.4.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the WAN service t ype on the screen. ...
-
TP-Link TD-VG3511 - page 37
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 28 Figure 4-8 ¾ IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. If you forget, you can ask your ISP. ¾ DNS Server/Secondary DNS Server: Type in your preferred DNS server. ¾ Default Gatewa y: select a WAN Interface from the drop-down list as the IPv4 de ...
-
TP-Link TD-VG3511 - page 38
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 29 Figure 4-9 ) Note: After you finish the Internet configuration, please click Save to m ake the settings take e ffe ct. 4.4.2 EWAN Choose “ Netw ork ” Æ “ EWAN ”, and you will see the Ethernet WAN Interface screen similar to Figure 4-10 . There are there different configura ...
-
TP-Link TD-VG3511 - page 39
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 30 Figure 4-10 4.4.2.1 Dy n ami c IP Select this option, the Modem Router will be abl e to obtain IP network information dynamically from a DHCP server provided by your ISP (as shown Figure 4-10 ). The next configuration is similar to Dynamic IP over ATM interface (see section 4.4.1.2 ...
-
TP-Link TD-VG3511 - page 40
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 31 Figure 4-11 4.4.2.3 PPPoE If your ISP provides a PPPoE connection and you need to use an Ethernet Interface, select PPPoE option for the WAN service type on the screen. The following configuration is similar to PPPoE over ATM interface (see section 4.4.1.3 PPPoE ). ...
-
TP-Link TD-VG3511 - page 41
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 32 Figure 4-12 4.4.3 Interface Grouping Choose “ Network ” Æ “ Interface Grouping ”, you can view all the current groups on this page (shown in Figure 4-13 ). ...
-
TP-Link TD-VG3511 - page 42
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 33 Figure 4-13 ¾ VLAN: Enable or disable this function. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same LAN, when in fact they are located on a number of different LAN segments. Because ...
-
TP-Link TD-VG3511 - page 43
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 34 Figure 4-14 Click Save to make the entry effective immediately 4.4.4 LAN Settings Choose “ Network ” Æ “ LAN Settings ” menu, and you will see the LAN screen (shown in Figure 4-15 ). Please configure the param eters for LAN ports according to the descriptions belo w. ...
-
TP-Link TD-VG3511 - page 44
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 35 Figure 4-15 ¾ IP Address: You can configure the Modem Router’s IP Address and Subnet Mask for LAN Interface. • IP Address: Enter the Modem Router’s local IP A ddress, then you can access to the Web-based Utility via the IP Addre ss, the default val ue is 192.168.1.1. • Sub ...
-
TP-Link TD-VG3511 - page 45
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 36 • End IP Address: Enter a value for the DHCP server to end with when issuing IP addresses. The End IP Address must be sm aller than 192.168.1.254. The default End IP Address is 192.168.1.199 . • Leased Time: The Leased Time is the amount of ti me in which a network user will be ...
-
TP-Link TD-VG3511 - page 46
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 37 Figure 4-17 ¾ Virtual Private Network (VPN) - VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pa ss through the Modem Router. • PPTP Passthrough - Point-to-Point Tunneling Pr otocol (PPTP) allows the Point-to-Point Protocol (PPP) to be t u ...
-
TP-Link TD-VG3511 - page 47
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 38 Figure 4-18 ¾ DSL Modulation Type: Select the DSL operation Modulation Type which your DSL connection uses. ¾ Annex Type: Select the DSL operation Annex Type which your DSL connection uses. Click the Save button to save your settings. 4.5 DHCP Server Choose “ DHCP Server ”, y ...
-
TP-Link TD-VG3511 - page 48
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 39 Figure 4-19 ¾ Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Modem Router is 192.168.1.1, the default Start IP Address is 192.168.1.100 , and the Start IP Address must be 192.168.1.2 or greater, b ...
-
TP-Link TD-VG3511 - page 49
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 40 ) Note: 1) To use the DHCP server func tion of the Modem Router, you mu st configure all computers on the LAN as "Obtain an IP Address automatically". 2) Y ou have to disable NA T of the W AN connections, or the DHCP Relay may not take ef fect. 3) If you select Disabled , ...
-
TP-Link TD-VG3511 - page 50
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 41 Figure 4-21 ¾ MAC Address: The MAC address of the PC for which you want to reserve an IP address. ¾ IP Address: The IP address reserved for the PC by the Modem Router. ¾ Status: The status of this entry either Enabled or Disabled . To Reserve an IP address: 1. Click the Add New ...
-
TP-Link TD-VG3511 - page 51
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 42 Figure 4-23 To add a vendor class: 1. Click the Add New button. Then Figure 4-24 will pop up. 2. Enter param eters for the vendor class. Click the Save button. Figure 4-24 To modify or delete an existing entry: 1. Click the Edit in the entry you want to modify. If yo u want to dele ...
-
TP-Link TD-VG3511 - page 52
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 43 4.6 Wireless Choose “ Wireless ”, there are six submenus to configure Wireless LAN settings. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.6.1 Basic Settings Choose “ Wireless ...
-
TP-Link TD-VG3511 - page 53
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 44 Router in a region other than one of those specified in this field . If your country or region is not listed, please contact your local government agency for assistance. ¾ Mode : Select the desired mode. 11b only: Select if all of your wireless clients are 802.11b. 11g only: Selec ...
-
TP-Link TD-VG3511 - page 54
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 45 ¾ SSID (to be bridged): The SSID of the AP your Modem R outer is going to connect to as a client. You can also use the search f unction to select the SSID to join. ¾ BSSID (to be bridged): The BSSID of the AP your Modem R outer is going to connect to as a client. You can also use ...
-
TP-Link TD-VG3511 - page 55
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 46 ¾ WPS: Enable or disable the WPS function here. ¾ Current PIN: The current value of the Modem Router's PIN is displayed here. The default PIN of the Modem Router can be found in the label or User Guide. ¾ Restore PIN: Restore the PIN of the Modem Router to its default. ¾ G ...
-
TP-Link TD-VG3511 - page 56
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 47 Figure 4-27 Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for tw o minutes during the Wi-Fi Protected Setup process. Step 4: When the W PS LED is on, the client device has successfu lly connected to the Modem Rout ...
-
TP-Link TD-VG3511 - page 57
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 48 ) Note: 1) The WPS LED on the Modem R outer will light green for five minutes if t he device has been successfully added to the network. 2) The WPS function cannot be c onfigured if the Wireless Functi on of the Modem Router is disabled. Please make sure the Wireless Func tion is e ...
-
TP-Link TD-VG3511 - page 58
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 49 Figure 4-30 • Auth Type - you can choose the type for the W EP security on the drop-down list. The default setting is Automatic , which can select Shared Key or Open System authentication type automatically based on the wire less station's capability and request. • WEP Key ...
-
TP-Link TD-VG3511 - page 59
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 50 • PSK Password - You can enter ASCII characters betwe en 8 and 63 characters or 8 to 64 Hexadecimal characters. • Group Key Update Period - Specify the group key update inte rval in seconds. The value should be 30 or above. Ente r 0 to disable the update. Be sure to click the S ...
-
TP-Link TD-VG3511 - page 60
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 51 3. Select Enabled or Disabled for this entry on the Status drop -down list. 4. Click the Save button to save this entry. T o edit or delete an existing entry: 1. Click the Edit in the entry you want to modify. 2. Modify the information. 3. Click the Save button. Click the Enable/ D ...
-
TP-Link TD-VG3511 - page 61
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 52 Figure 4-33 ¾ Transmit Power: Here you can specify the transmit power of Modem Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾ Beacon Interval: Enter a value between 25- 1000 milliseconds for Beac on Interval here ...
-
TP-Link TD-VG3511 - page 62
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 53 4.6.6 Wireless Status Choose menu “ Wireless ” Æ ” Wireless Status ”, you can see the MAC A ddr ess, Current Status, Received Packets and Sent Packets fo r each connected wireless station. Figure 4-34 ¾ MAC Address: The connected wireless station's MAC address ¾ Cur ...
-
TP-Link TD-VG3511 - page 63
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 54 Figure 4-35 ¾ Profile Name: Displays the profile name of the account. ¾ Registrar Address: Displays the IP address or domin name of the SIP Registrar server. ¾ Phone Number: Displays the phone number of the account. ¾ Status: Displays the status of t he account. “Down” mean ...
-
TP-Link TD-VG3511 - page 64
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 55 ¾ Display Name: Assign a name for your account. This name is the Caller-ID you want to be displayed on your friend’s display panel, which c an let your friend easily know who is calling. Please note that special characters are not allowed. ¾ Authentication ID: Enter the name or ...
-
TP-Link TD-VG3511 - page 65
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 56 This section includes Dial Plan List and Forbidden Call. The function allows users to set rules for outgoing calls. 4.7.2.1 Dial Plan List Choose “ Voice ” Æ “ Dial Plan ” Æ “ Dial Plan List ”, you will see the screen similar to Figure 4-37 . Dial plan List allows the ...
-
TP-Link TD-VG3511 - page 66
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 57 ¾ Prefix: Set number(s) as the prefix. Up to 16 characters can be entered. ¾ Destination: SIP account can be selected here. As to which one will be finally used, it depends on not only Destination selected here but also Dia l Plan Priority configured on Phone Setup page. Please n ...
-
TP-Link TD-VG3511 - page 67
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 58 Figure 4-39 ¾ Prefix: Displays the prefix of your plan. This prefix refers to the initial digit(s) of the num bers you dial. ¾ Forbidden: Displays the interface(s) disabled in this plan. ¾ Remove: Check the box and then click the Remove button below so that the very plan will be ...
-
TP-Link TD-VG3511 - page 68
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 59 Figure 4-41 ¾ Phone Enable: Check the box behind to enable the function. Dial Settings ¾ Dial Plan Priority: The parameters configured in the 2 nd field determine which SIP account to use when making outgoing calls. The fo llowing are different options: • VOIP & Auto – Th ...
-
TP-Link TD-VG3511 - page 69
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 60 ¾ Warmline Number: Click “ View/Set ” button to view or set Warmline Number. Answer Settings ¾ MWI Mode: Options available are VMWI and CLID. If you don't know, please consult your service provider. ¾ Anonymous Call Blocking: Check the box to deny anonymous incoming cal ...
-
TP-Link TD-VG3511 - page 70
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 61 Figure 4-42 SIP Advanced Setup: ¾ Bound Interface Name: Bound Interface decides where to send/receive the VOIP traffic. Easy way to select the interface is to check the location of the SIP server. If it lo cates some where in the Internet then select Any_WAN . If it is on the loca ...
-
TP-Link TD-VG3511 - page 71
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 62 facsimile terminals over the Internet or other networks using IP protocol s. It will only function when both sites support this feature and are enabled. 4.7.5 Speed Dial Choose “ Voice ” Æ “ Speed Dial ”, you will see the screen as shown in Figure 4-43 . This section intro ...
-
TP-Link TD-VG3511 - page 72
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 63 4.7.6 Call Log Choose “ Voice ” Æ “ Call Log ”, you will see the screen as shown in Figure 4-46 . This function allows you to view call logs and configure call log options. Figure 4-46 ¾ Call Log: Check the Enable if you want to make this function take effect; otherwise c ...
-
TP-Link TD-VG3511 - page 73
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 64 Call Firewall can be used to control incoming calls. This section introduces how to configure the Call Firewall. Choose “ Voice ” Æ “ Call Firewall “ Æ “ Mode Setting “, you will see the screen as shown in Figure 4-48 . Figure 4-48 ¾ Call Firewall Enable: Check the b ...
-
TP-Link TD-VG3511 - page 74
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 65 Figure 4-50 Enter a number with the length in t he range of [3, 16]in the field of Black List Number and Click the Save button to make the configuration take effe ct, then you will go back to the previous page and see the following list as shown in Figure 4-49 . If you want to dele ...
-
TP-Link TD-VG3511 - page 75
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 66 4.7.8 USB Voice Mail Choose “ Voice ” Æ “ USB Voice Mail “, you will see the screen as shown in Figure 4-53 . USB Voice mail is used to record voice messages when the call is not answered. To us e this function, please make sure an external USB hard drive/USB flas h disk w ...
-
TP-Link TD-VG3511 - page 76
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 67 Figure 4-54 ¾ Enable Local Play Operation Notify: Check this box so there will be sound indication for operation when you listen to the voice messages. This is enabled by default. If you are very familiar with the operation s, you can disable it. ¾ Enable Global Wav Format: Check ...
-
TP-Link TD-VG3511 - page 77
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 68 3) Input the PIN code according to the notification. 4) You can listen to all the new mess ages after the PIN code is validated. Click Save to save your configurations. Click Back to go back to the previous page, i.e. Figure 4-53 . 4.8 USB Settings There are six submenus under the ...
-
TP-Link TD-VG3511 - page 78
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 69 ¾ File System: The system of the USB drive. ¾ Capacity: The storage capacity of the USB driver. ¾ Status: Indicates the shared or non- shared status of the volume. Online means volume can be shared, while Offline means volume can not be shared. If Deactivate in Action field is e ...
-
TP-Link TD-VG3511 - page 79
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 70 3. Enter the password in the New Password field. 4. Re-enter the password in the Confirm Passw ord field. 5. Click the Set button, and then a new entry will be added in the table. 6. Click the Apply button to apply your settings. Click the Refresh button to refresh this page immedi ...
-
TP-Link TD-VG3511 - page 80
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 71 1. Click Add New Folder in Figure 4-57 . Figure 4-58 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button ...
-
TP-Link TD-VG3511 - page 81
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 72 Figure 4-59 ¾ Server Status: Indicates the FTP Server's current status. ¾ Internet Access: Enable or disable this function. ¾ Internet Address: If Internet Access is enabled, WAN IP will be displayed here. ¾ Service Port: Enter the FTP Port number to use. The default is 21 ...
-
TP-Link TD-VG3511 - page 82
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 73 Figure 4-60 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder. Click the Ena ...
-
TP-Link TD-VG3511 - page 83
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 74 ¾ Server Enable: Select this box to enable this function. ¾ Server Name: The name of this Media Server. To add a new share folder for your media server, please follow the instructions below: a) Click Add Ne w Folder button, and you will see the screen as shown in Figure 4-62 . b) ...
-
TP-Link TD-VG3511 - page 84
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 75 4.9 Route Settings Choose “ Route Settings ”, it includes three menus : Default Gatew ay , Static Route and RIP Settings . The detailed descriptions are provided below. 4.9.1 Default Gateway Choose “ Route Settings ” Æ “ Default Gatewa y ”, you can see the Default Gate ...
-
TP-Link TD-VG3511 - page 85
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 76 Figure 4-66 2. Enter the following data: ¾ Destination IP Address: The Destination IP Addr ess is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask: The Subnet Mask determines which portion of an IP Address is the network portion, and whi ...
-
TP-Link TD-VG3511 - page 86
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 77 ) Note: RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE). 4.10 Forwarding There are four submenus under the Forwarding menu: Virtual Servers , Port Triggering , DMZ and UPnP . Click any of them, and you will be able to configure the corre sponding ...
-
TP-Link TD-VG3511 - page 87
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 78 2. Select the service y ou w ant to use from the Common Service Port list. If the Common Service Port menu does not list the serv ice that you want to use, enter the number of the service port or service port range in the Service Port field. 3. Select the service you want to use fr ...
-
TP-Link TD-VG3511 - page 88
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 79 Figure 4-70 To add a new rule, follow the steps below. 1. Click the Add New button, the next screen will pop-up as shown in Figure 4-71 . 2. Select a co mmon application from the Common Service Port drop-down list, then the Trigger Port field and the Open Ports field will be automa ...
-
TP-Link TD-VG3511 - page 89
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 80 ¾ Open Protocol: The protocol used for Incoming Port , either TCP , UDP , or ALL (all protocols supported by the Modem Router). ¾ Status: The status of this entry, Enabled means the Port Triggering entry is enabled. ¾ Modify: To modify or delete an existing entry. ¾ Common Serv ...
-
TP-Link TD-VG3511 - page 90
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 81 Figure 4-72 To assign a computer or server to be a DMZ server: 1. Click the Enable button. 2. Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field. 3. Click the Save button. 4.10.4 UPnP Choose menu “ Forwarding → UPnP ”, and then you ...
-
TP-Link TD-VG3511 - page 91
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 82 Click the Disable button to disable UPnP. Click the Refresh button to update the Curr ent UPnP Settings List. 4.11 Parent al Control Choose menu “ Parental Control ”, and you can configure the paren tal control in the screen as shown in Figure 4-74 . The Parental Control functi ...
-
TP-Link TD-VG3511 - page 92
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 83 ¾ MAC Address of Current PC: This field displays the MA C address of the PC that is managing this Modem Router. If the MAC Address of your adapter is registered, you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above. ¾ Add URL: ...
-
TP-Link TD-VG3511 - page 93
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 84 ¾ Add New: Click the Add New button to add a new rule entry. ¾ Enable Selected: Click the Enable Selected button to enable the selected rules in the list. ¾ Disable Selected: Click the Disable Selected button to disable the selected rules in the list. ¾ Delete Selected: Click t ...
-
TP-Link TD-VG3511 - page 94
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 85 ¾ Description: Here displays the description of the host and this description is unique. ¾ Address Info: Here displays the information about the host. It can be IP or MAC. ¾ Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add Ne ...
-
TP-Link TD-VG3511 - page 95
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 86 Figure 4-79 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In IP Address field, enter the IP address. If you select MAC Address , the screen shown is Figure 4-80 . Figure 4-80 1) In Description field, create a unique description for the host (e. ...
-
TP-Link TD-VG3511 - page 96
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 87 4.12.4 Schedule Choose menu “ Firewall ” → “ Schedule ”, and then you can view and set a Schedule list in the next screen as shown in Figure 4-82 . Figure 4-82 ¾ Description: Here displays the description of the schedule and this description is unique. ¾ Edit: Here you ...
-
TP-Link TD-VG3511 - page 97
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 88 Click the Delete Selected button to delete the select ed entries in the table. 4.13 Bandwid th Control Choose menu “ Bandwidth Control ”, and then you can configur e the Upstream Bandwidth, Downstream Bandwidth and Bandwidth Control rul e s for computers in LAN in the next scre ...
-
TP-Link TD-VG3511 - page 98
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 89 Figure 4-85 3. Click the Save button. 4.14 IP&MAC Binding There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List . Click any of them, and you will be able to scan or configure the corre s ponding function. The detailed explanations for eac h su ...
-
TP-Link TD-VG3511 - page 99
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 90 ¾ Bound: Check this option to enable ARP binding for a specific device. ¾ Edit: To modify or delete an existing entry. When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Edit button, and then you will go to the next page. Th is page ...
-
TP-Link TD-VG3511 - page 100
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 91 ¾ IP Address: The assigned IP address of the cont rolled computer in the LAN. ¾ Status: Indicates whether or not the MAC and IP addresses are bound. ¾ Load: Load the item to the IP & MAC Binding list. Click the Load Selected button to load selected items to the IP & MAC ...
-
TP-Link TD-VG3511 - page 101
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 92 Figure 4-90 4.17 System T ools Choose menu “ System Tools ”, and you can see the s ubmenus under the main menu: System Log , Time Settings , Manage Control , CWMP Settings , SNMP Settings , Backup & Restore , Factory Defaults , Firm ware Upgrade , Reboot and Statistics. Cli ...
-
TP-Link TD-VG3511 - page 102
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 93 Figure 4-91 ¾ Log Type: By selecting th e log type, only logs of this type will be shown. ¾ Log Level: By selecting the log level, only logs of this level will be shown. ¾ Refresh: Refresh the page to show the latest log list. ¾ Clear Log: All the logs will be deleted from the ...
-
TP-Link TD-VG3511 - page 103
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 94 Figure 4-93 ¾ Time Zone: Select your local time zone from this pull down list. ¾ Date: Enter your local date in MM/DD/YY into the right blanks. ¾ Time: Enter your local time in HH/ MM/SS into th e right blanks. ¾ NTP Server 1 / NTP Server 2: Enter the address or domain of the N ...
-
TP-Link TD-VG3511 - page 104
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 95 Figure 4-94 ¾ Current User Status: This box displays the information about User Type , User Name , Host IP Address and Host MAC Address . ¾ Account Management: Here you can set the account user information about Old Passw ord , New User Name , New Password and Confirm Passw ord . ...
-
TP-Link TD-VG3511 - page 105
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 96 Figure 4-95 ¾ CWMP: Select enable the CWMP function. ¾ Inform: Enable or disable the function. If enabl ed, the information will be informed to ACS server periodically. ¾ Inform Interval: Enter the interval time here. ¾ ACS URL: Enter the website of ACS whic h is provided by yo ...
-
TP-Link TD-VG3511 - page 106
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 97 Figure 4-96 An SNMP Agent is an application running on the Modem Router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs. So a rout er contains SNMP "agent" software ...
-
TP-Link TD-VG3511 - page 107
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 98 Figure 4-98 Click the Restore button to reset all configuration settings to their default values. • The default User Name : admin • The default Password : admin • The default Subnet Mask : 255.255.255.0 ) Note: All changed settings will be lost when defaults are restored. 4.1 ...
-
TP-Link TD-VG3511 - page 108
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 99 want to use. However, when experiencing probl ems caused by the Modem Router rather than the configuration, you can try to upgrade the firmware. 2) When you upgrade the Modem R outer's firmware, you may lose its current configurations, so before upgrading the firmware please w ...
-
TP-Link TD-VG3511 - page 109
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 100 Figure 4-101 ¾ Statistics Status: Enable or Disable. The default value is disabled. To enable it, click the Enable . If it is disabled, the func tion of DoS protection in Securi ty settings will be disabled. ¾ Statistics Interval (5-60): The default value is 10. Select a value b ...
-
TP-Link TD-VG3511 - page 110
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 101 Appendix A: Sp ecifications General Standards and Protocols ANSI T1.413.I2, ITU G.992.1, ITU G. 992.2, ITU G.992.3, ITU G.992.5, IEEE802.1p, IEEE 802.11b,IEEE 802.11e, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IE EE 802.3u, TCP/IP, PPPoA, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT Safety &a ...
-
TP-Link TD-VG3511 - page 111
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 102 Appendix B: T roubleshooting T1. How do I restore my Modem Router’s configur ation to its factory default settings? With the Modem Router powered on, press and hold the RESET button on the back panel for 8 to 10 seconds before releasing it. ) Note : Once the Modem Router is rese ...
-
TP-Link TD-VG3511 - page 112
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 103 Click Change adapter settings Click Properties Right-click Local Area Connection ...
-
TP-Link TD-VG3511 - page 113
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 104 Double-click Internet Protocol Version 4 (TCP/IPv4) Click OK Select Obtain DNS server address automatically Select Obtain an IP address automatically ...
-
TP-Link TD-VG3511 - page 114
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 105 For Windows Vista OS Go to Start > Settings > Control Panel , and then you will see the following page. Click View network status and tasks Click View status Click Properties ...
-
TP-Link TD-VG3511 - page 115
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 106 Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK ...
-
TP-Link TD-VG3511 - page 116
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 107 For Windows XP OS Go to Start > Control Panel , you will then see the following page. Click Network Connections Right-click Local Area Connection Click Network and Internet Connections Click Properties ...
-
TP-Link TD-VG3511 - page 117
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 108 Double-click Internet Protocol (TCP/IP) Select Obtain DNS server address automatically Select Obtain an IP address automatically Click OK ...
-
TP-Link TD-VG3511 - page 118
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 109 Click OK 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options ...
-
TP-Link TD-VG3511 - page 119
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 110 Click OK Select Never dial a connection Now, try to log on to the Web- based configuration page again afte r the above settings have been configured. If you still cannot acce ss the configuration page, please restore your Modem Router’s factory default settings and re configure ...
-
TP-Link TD-VG3511 - page 120
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 111 2) Insert the provided Resource CD into CD-ROM drive of your computer. 3) Please select your product model and click Start Setup . 4) Then the configur ation wizard will pop up and show you how to connect your devices. After that, the Easy Setup Assistant will start. Click NEXT , ...
-
TP-Link TD-VG3511 - page 121
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 112 5) When it comes to Configure USB Voice Mail page, check boxes before Configure USB Voice Mail and Send Files to USB Disk , enable USB Mail for Line 1 or Line 2. Then click NEXT to continue. 6) Follow the step-by-step instructions unt il you comes to the finish screen. Click FINIS ...
-
TP-Link TD-VG3511 - page 122
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 113 7) The configure files can be found in your USB device which means you have successfully configured the USB device for USB Voice Mail function. ...
-
TP-Link TD-VG3511 - page 123
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 114 Appendix C: T elephony Features Call Holding This feature allows you to put a call on hold, in which case the call is not ended but no verbal communication is available. To put a call on hold, press the FLASH button. To return to the original call, press the FLASH button again. Ca ...
-
TP-Link TD-VG3511 - page 124
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 115 Anonymous Call Blocking With this feature enabled, all anonymous calls will be blocked. Speed Dial This feature allows you to create short number s for your freq uently used telephone numbers to make your dialing more convenient. You just need to press one or two digits and the ke ...
-
TP-Link TD-VG3511 - page 125
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 116 Appendix D: T elephone Operation Code Description Usage *20 Listen to voice messages stored in your USB storage device. Pick up the phone to dial this code and then follow the voice prompts for the operations below: Press 0 to listen to new messages. Press 1 to listen to the previ ...
-
TP-Link TD-VG3511 - page 126
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 117 *69 Dial the last incoming number. Pick up the phone to dial this code. The last incoming number will be dialed automatically. *68 Dial the last outgoing number. Pick up the phone to dial th is code. The last outgoing number will be dialed automatically. *78 Enable Warm Line. Pick ...
-
TP-Link TD-VG3511 - page 127
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 118 Appendix E: T echnical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/e n/support/faq T o download the latest Firm ware, Driver , Utility and User Guide, go to: http://www .tp-link .com/en/support/do wnload For all other technica ...
Do you have a question concerning TP-Link TD-VG3511?
Use the form below
If you did not solve your problem by using a manual TP-Link TD-VG3511, ask a question using the form below. If a user had a similar problem with TP-Link TD-VG3511 it is likely that he will want to share the way to solve it.