English dropdown-ico

Manual Delta 17-925

20 pages 0.69 mb
Download

Go to site of 20

Summary
  • Delta 17-925 - page 1

    INSTRUCTION MANUAL P ART NO. A10354 - 04-06-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 16-1/2" V ariable Speed Drill Pr ess (Model 17-925) (Model 17-99 ...

  • Delta 17-925 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Delta 17-925 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta 17-925 - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • Delta 17-925 - page 5

    5 SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. ADDITIONAL SPECIFIC SAFETY RULES 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according t o t h e instructions. A machine incorrectly assembled can cause serious injury . 2. OBT AIN ADVICE from your supervisor , instructor , or another ...

  • Delta 17-925 - page 6

    Y ou can have your drill press converted to 230 volt operation. A qualified electrician must perform this conversion. Should you desire to have your drill pr ess converted for 230 volt operation, take your drill press to your local Authorized Delta Service Center . Y ou can call 800-223-7278 for the location of the nearest Authorized Service Center ...

  • Delta 17-925 - page 7

    7 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized ...

  • Delta 17-925 - page 8

    8 1 2 3 4 5 6 7 8 9 10 11A 11B 12 13 14 15 16 17 18 1. Drill Press Head 2. Column and T able Raising Rack 3. T able/Column Bracket 4. Lock Lever for Column Bracket 1/2-13x1-1/2" 5. Lock Lever for T able 3/8-16x1-1/8" 6. W orm for T able-Raising Mechanism 7. T able-Raising and Lowering Handwheel 8. T able 9. Chuck 10. Chuck Key 11A. Pinion ...

  • Delta 17-925 - page 9

    9 ASSEMBL Y ASSEMBL Y TOOLS REQUIRED ASSEMBL Y TIME ESTIMA TE 1. Attach the column (A) Fig. 3 to the base (B) using the four M10x40mm hex head screws (C), thr ee of which are shown. Loosely thr ead the locking lever (D) into the table mounting bracket (E). Loosen the set screw (D) with the supplied 3mm wr ench and remove the ring (E) and raising ra ...

  • Delta 17-925 - page 10

    10 5. Re-install the ring (E) Fig. 9 (removed in STEP 1) . IMPORT ANT : DO NOT push the ring (E) Fig. 9 all the way down on the the raising rack (F). Make certain that the top of the raising rack (F) is under the bottom of the ring (E) and that enough clearance is available to allow the rack (F) to rotate ar ound the column. Tighten the set screw ( ...

  • Delta 17-925 - page 11

    11 IMPORT ANT : Make certain that the spindle taper (Q) Fig. 16 and the tapered hole in the chuck (R) are clean and fr ee of any grease, lacquer , or rust-preventive coatings. NOTE: Household oven cleaner can effectively r emove any substance from the spindle and chuck. Car efully follow the manufacturer's safety rules concerning its use. IMPO ...

  • Delta 17-925 - page 12

    12 5. Thread the two speed-changing levers (W) Fig. 22 into the speed changing hub. 6. Thread the speed range-changing lever (X) Fig. 23 into the hub. Fig. 22 Fig. 23 MOUNTING DRILL PRESS ON A SUPPORTING SURF ACE Fig. 24 A MOUNTING THE DRILL PRESS ON A PL YWOOD BASE If you do not fasten your machine permanently , then you must fasten the drill pres ...

  • Delta 17-925 - page 13

    13 LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use, using a padlock (C) Fig. 28 with a 3/16" diameter shackle. In the event of a power outage, always lock switch in “OFF” position until the main power is restor ed. T ABLE ...

  • Delta 17-925 - page 14

    1. Insert the bit into the chuck. 2. Lower the chuck (C) Fig. 34, and the drill bit to your chosen depth by rotating the pinion shaft handles (D). Lock the quill in position by tightening the quill locking lever (E). NOTE: The quill locking lever (E) is spring-loaded. Change it by pulling out on the handle and repositioning the hub of the handle on ...

  • Delta 17-925 - page 15

    15 ADJUSTING THE SPINDLE RETURN SPRING The spindle will automatically return slowly to its upper position when the handle is released. The spindle r eturn spring was properly adjusted at the factory . However , to adjust, if necessary: 1. Loosen the nuts (B) and (E) Fig. 37, but do not remove. Make sure that the spring housing (A) r emains engaged ...

  • Delta 17-925 - page 16

    16 Fig. 39 A B D C NOTE: Use drill bits with a shank of 1/2" or less in diameter . DISCONNECT MACHINE FROM POWER SOURCE . 1. Insert the smooth end of drill bit (A) Fig. 39 in the chuck (B) as far as it will go, and then back the bit out 1/16" (or up to the flutes for small bits). 2. Center the drill bit (A) Fig. 39 in the chuck (B) befor ...

  • Delta 17-925 - page 17

    17 MAINTENANCE TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). LUBRICA TION Oil the variable speed pulleys and the speed range shifter mechanism weekly . Use a few dr ops of light m ...

  • Delta 17-925 - page 18

    18 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra ...

  • Delta 17-925 - page 19

    19 T wo Y ear Limited New Product W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized serv ...

  • Delta 17-925 - page 20

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Manufacturer Delta Category Drill

Documents that we receive from a manufacturer of a Delta 17-925 can be divided into several groups. They are, among others:
- Delta technical drawings
- 17-925 manuals
- Delta product data sheets
- information booklets
- or energy labels Delta 17-925
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta 17-925.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta 17-925, service manual, brief instructions and user manuals Delta 17-925. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta 17-925.

Similar manuals

A complete manual for the device Delta 17-925, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta 17-925 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta 17-925.

A complete Delta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta 17-925 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta 17-925, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta 17-925, that we can find in the current document
3. Tips how to use the basic functions of the device Delta 17-925 - which should help us in our first steps of using Delta 17-925
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta 17-925
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta 17-925 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta 17-925?

Use the form below

If you did not solve your problem by using a manual Delta 17-925, ask a question using the form below. If a user had a similar problem with Delta 17-925 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)