English dropdown-ico

Manual Eaton Electrical BladeUPS Bar

28 pages 2.38 mb
Download

Go to site of 28

Summary
  • Eaton Electrical BladeUPS Bar - page 1

    Powerware BladeUPS Bar Installation Guide ® ® ...

  • Eaton Electrical BladeUPS Bar - page 2

    Special Symbols The following are examples of symbols used on the UPS or accessories to alert you to important information: RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol. CAUTION: REFER TO OPERATOR’S MANUAL - R efer to your operator’s manual for additional information, such as important operating ...

  • Eaton Electrical BladeUPS Bar - page 3

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 i Table of Contents 1 Introduction 1 ......................................................... Safety Warnings 2 ...................................................................... 2 Installation 5 .......................................................... Inspecting the E ...

  • Eaton Electrical BladeUPS Bar - page 4

    TABLE OF CONTENTS EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 ii ...

  • Eaton Electrical BladeUPS Bar - page 5

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 1 Chapter 1 Introduction Up to six of Eaton’s Powerware ® BladeUPS ® uninterruptible power systems (UPSs) can be installed in an industry standard rack outfitted with a BladeUPS Bar 60 for interconnecting the cabinets’ wiring. Figure 1 shows an installed BladeUPS Bar 60 ...

  • Eaton Electrical BladeUPS Bar - page 6

    INTRODUCTION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 2 Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions t hat you should follow during installation and maintenance of the BladeUPS Bar 60. Please r ead all instructions before operating the equipment an ...

  • Eaton Electrical BladeUPS Bar - page 7

    INTRODUCTION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 3 WICHTIGE SICHERHEITSANWEISUNGEN AUFBEWAREN Dieses Handbuch enthält wichtige Hinweise, welche Sie bei der Installation und Wartung des BladeUPS Bar 60 beachten sollten. Bitte lesen Sie alle Anweisungen des H andbuches bevor sie mit dem Gerät arbeiten. Bewaren ...

  • Eaton Electrical BladeUPS Bar - page 8

    INTRODUCTION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 4 INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONES Este manual contiene instrucci ones importantes que debe seguir durante la instalación y el funcionamiento del BladeUPS Bar 60. Por favor, lea todas las instrucciones antes de poner en funcionam ...

  • Eaton Electrical BladeUPS Bar - page 9

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 5 Chapter 2 Installation This section explains: S Equipment inspection S BladeUPS Bar 60 setup and installation Inspecting the Equipment If any equipment has been damaged during shipment, keep the shipping cartons and packing materials for the carrier or place of purchase and ...

  • Eaton Electrical BladeUPS Bar - page 10

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 6 Checking the Package Contents Verify that the following items are included: S BladeUPS Bar 60 A six - socket bar with (1) attached terminal block assembly, (1) attached base bracket, and (3) attached mounting brackets S Wireway main housing with (2) attached si ...

  • Eaton Electrical BladeUPS Bar - page 11

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 7 Installation To install the BladeUPS Bar 60: 1. Remove the access cover and terminal block housing from the wireway housing (see Figure 2). Retain the wireway terminal block housing, wireway access cover, and screws. Leave the two side brackets installed on the ...

  • Eaton Electrical BladeUPS Bar - page 12

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 8 4. Install an M6 hex nut onto each of the three wireway studs to secure the wireway to the rear of the rack. Install the first stud in the fourth hole location from the bottom. Do not tighten the nuts. Figure 4 shows the nuts installed. 5. Loosen the three adju ...

  • Eaton Electrical BladeUPS Bar - page 13

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 9 9. Place the ferrite assembly on the floor of the wireway and secure with the supplied tie wrap. Loop the tie wrap through both attachment sites on the wireway floor and through the ferrite assembly. See Figure 4. 10. Note the orientation of the base bracket in ...

  • Eaton Electrical BladeUPS Bar - page 14

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 10 NOTE Verify that the bar is secure as shown in F igure 4. The sheetmetal at the base of the bar should be below the tab on the wireway floor. 12. Secure the bar to the wireway with three M6 × 12 hex bolts. Install the bolts from the front of the rack. See Fig ...

  • Eaton Electrical BladeUPS Bar - page 15

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 11 14. Secure the base bracket to the rack with three M6 × 12 hex bolts. Install the bolts from the rear of the rack. Use a large screwdriver or crowbar to lift the bar in place to align the holes in the base bracket with the holes in the rack. Install the lowes ...

  • Eaton Electrical BladeUPS Bar - page 16

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 12 16. Install two M4 × 8 pan - head screws into the tab on the wireway floor, securing the base of the bar to the wireway. See Figure 7. Torque the screws to 1.7 ± 0.2 Nm (15 ± 2l bi n ) . Rear of Rack Wireway Floor Tab (above bar base sheetmetal) M4 × 8 Pan ...

  • Eaton Electrical BladeUPS Bar - page 17

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 13 17. Using two M6 × 12 hex bolts, secure the left side of the wireway terminal block housing to the rack. See Figure 8. Torque the bolts to 5.1 ± 0.8 Nm (45 ± 7l bi n ) . 18. Using nine M4 × 8 pan - head screws, secure the wireway terminal block housing to ...

  • Eaton Electrical BladeUPS Bar - page 18

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 14 19. Using five M4 × 8 pan - head screws, install the wireway access cover. See Figure 9. Torque the screws to 1.7 ± 0.2 Nm (15 ± 2l bi n ) . M4 × 8 Pan-Head Screws (5 places) Wireway Access Cover Figure 9. Wireway Access Cover Installation 20. Verify the s ...

  • Eaton Electrical BladeUPS Bar - page 19

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 15 21. Using four M5 × 16 hex bolts and four M5 cage nuts, secure the front cover mounting panel to the front of the rack. Verify that the bent edge of the panel is at the top. See Figure 11. Install the lower bolts and cage nuts into the second holes from the b ...

  • Eaton Electrical BladeUPS Bar - page 20

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 16 22. Snap the two front covers into place, as shown in Figure 12. Front Covers (2 pieces) Figure 12. Front Cover Installation ...

  • Eaton Electrical BladeUPS Bar - page 21

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 17 Chapter 3 Specifications This section provides the following specifications: Table 1. BladeUPS Bar 60 Dimensions (WxDxH) 14.0 × 11.3 × 183.8 cm (5.5 ” × 4.4 ” × 72.4 ” ) Depth of Wireway 90.1 cm (35.5 ” ), excluding front covers Weight Bar: 19 kg (42 lb) Wirewa ...

  • Eaton Electrical BladeUPS Bar - page 22

    SPECIFICATIONS EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 18 ...

  • Eaton Electrical BladeUPS Bar - page 23

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 19 Chapter 4 Service and Support If you have any questions or problems with the BladeUPS Bar, call your Local Distributor or the Help Desk at one of the following telephone numbers and ask for a UPS technical representative. United States: 1-800-843-9433 or 1-919-870-3028 Can ...

  • Eaton Electrical BladeUPS Bar - page 24

    SERVICE AND SUPPORT EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 20 ...

  • Eaton Electrical BladeUPS Bar - page 25

    ...

  • Eaton Electrical BladeUPS Bar - page 26

    ...

  • Eaton Electrical BladeUPS Bar - page 27

    ...

  • Eaton Electrical BladeUPS Bar - page 28

    *164201723P01* 164201723 P01 ...

Manufacturer Eaton Electrical Category Power Supply

Documents that we receive from a manufacturer of a Eaton Electrical BladeUPS Bar can be divided into several groups. They are, among others:
- Eaton Electrical technical drawings
- BladeUPS Bar manuals
- Eaton Electrical product data sheets
- information booklets
- or energy labels Eaton Electrical BladeUPS Bar
All of them are important, but the most important information from the point of view of use of the device are in the user manual Eaton Electrical BladeUPS Bar.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Eaton Electrical BladeUPS Bar, service manual, brief instructions and user manuals Eaton Electrical BladeUPS Bar. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Eaton Electrical BladeUPS Bar.

Similar manuals

A complete manual for the device Eaton Electrical BladeUPS Bar, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Eaton Electrical BladeUPS Bar by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Eaton Electrical BladeUPS Bar.

A complete Eaton Electrical manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Eaton Electrical BladeUPS Bar - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Eaton Electrical BladeUPS Bar, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Eaton Electrical BladeUPS Bar, that we can find in the current document
3. Tips how to use the basic functions of the device Eaton Electrical BladeUPS Bar - which should help us in our first steps of using Eaton Electrical BladeUPS Bar
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Eaton Electrical BladeUPS Bar
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Eaton Electrical BladeUPS Bar in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Eaton Electrical BladeUPS Bar?

Use the form below

If you did not solve your problem by using a manual Eaton Electrical BladeUPS Bar, ask a question using the form below. If a user had a similar problem with Eaton Electrical BladeUPS Bar it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)