English dropdown-ico

Manual Quantum DLT-S4

22 pages 1.27 mb
Download

Go to site of 22

Summary
  • Quantum DLT-S4 - page 1

    DL T -S4 T ape Drive Quick Start Guide English - - - - - - - - - - - 1 German - - - - - - - - - - 4 Sp anish - - - - - - - - - - 7 French - - - - - - - - - - 10 Jap anese - - - - - - - - 13 Korean - - - - - - - - - - 16 Simplified Chinese - 19 Getting Started 0 This guide describes how to install the tape drive. T o get started: 1 Inspect the shipp ...

  • Quantum DLT-S4 - page 2

    DL T -S4 T ape Drive Quick Start Guide 2 The tape drive performs a self-diagnostic test, called a Power -On Self- T est (POST), each time you power it on. 3 During POST , each LED lights in sequence. When POST has completed successfully , the middle LED stops flashing and remains illuminated and the left and right LEDs remain off. 4 Power off the t ...

  • Quantum DLT-S4 - page 3

    DL T -S4 T ape Drive Quick Start Guide 3 Confirming the Installation 0 Follow these steps to confirm that the installation was successful: 1 Connect the power cord, then power on the tape drive and the host computer . 2 Confirm that the computer re cognizes the tape drive by watching the BIOS, OS, and SCSI controller information displayed at startu ...

  • Quantum DLT-S4 - page 4

    DL T -S4-Bandlaufwerk K urzanleitung Englisch - - - - - - - - - - 1 Deut sch - - - - - - - - - - 4 Sp anisch - - - - - - - - - 7 Französisch - - - - - - 10 Jap anisch - - - - - - - - 13 Koreanisch - - - - - - - 16 V ereinfachtes Chinesisch - - - - - - - 19 Zum Einstieg 0 In diesem Handbuch wird die Installati on des Bandlaufwerks beschrieben. Erst ...

  • Quantum DLT-S4 - page 5

    DL T -S4-Bandlaufwerk: Kurzanleitung 5 Abbildung 1 Bandlaufwerk überprüfen Das Bandlaufwerk führt bei jedem Einschalten einen Selbstdiagnosetest, genannt POST , aus. 3 Während des POST leuchten alle LEDs nacheinander auf. W enn der POST erfolgreich abgeschlossen ist, hört die mittlere LED auf, zu blinken und leuchtet konstant. Die linke und re ...

  • Quantum DLT-S4 - page 6

    DL T -S4-Bandlaufwerk: Kurzanleitung 6 Abbildung 4 Anschließen der SCSI-Kabel (Reihenschaltung) Überprüfung der Installation 0 Überprüfen Sie mit den folgenden Schritten, ob die Installation erfolgreich war: 1 Schließen Sie das Netzkabel an, und schalten Sie dann das Bandlaufwerk und den Hostcomputer ein. 2 Prüfen Sie, ob der Computer das Ba ...

  • Quantum DLT-S4 - page 7

    Unidad de cinta DL T -S4 Manual de referencia Inglés - - - - - - - - - - - - 1 Alemán - - - - - - - - - - - 4 Esp añol - - - - - - - - - - 7 Francés - - - - - - - - - 10 Japonés - - - - - - - - - 13 Coreano - - - - - - - - - 16 Chino simplificado - 19 P ara comenzar 0 Esta guía describe cómo instalar la unidad de cinta. Para comenzar: 1 Insp ...

  • Quantum DLT-S4 - page 8

    Unidad de cinta DL T -S4 Manual de referencia 8 Figura 1 Comprobación de la unidad de cinta La unidad de cinta realiza una prueba de autodiagnóstico, llamada autoprueba de encendido (POST), cada vez que usted la enciende. 3 Durante la POST , todos los indicadores LED se encienden en secuencia. Cuando la autoprueba de encendido (POST) concluye con ...

  • Quantum DLT-S4 - page 9

    Unidad de cinta DL T -S4 Manual de referencia 9 Figura 4 Conexión de los cables SCSI (conexión en cadena) Confirmación de la instalación 0 Siga estos pasos para confirmar que la instalación se haya realizado satisfactoriamente: 1 Conecte el cable de alimenta ción y luego encienda la unidad de cinta y el equipo host. 2 Confirme que el equipo r ...

  • Quantum DLT-S4 - page 10

    Lecteur de bande DL T -S4 Guide de démarrage rapide Anglais - - - - - - - - - - - 1 Allemand - - - - - - - - - 4 Esp agnol - - - - - - - - - 7 Français - - - - - - - - - 10 Japonais - - - - - - - - 13 Coréen - - - - - - - - - - 16 Chinois simplifié - - 19 Mise en route 0 Ce guide décrit comment installer le lecteu r de bande. Pour la mise en r ...

  • Quantum DLT-S4 - page 11

    Lecteur de bande DL T -S4 : Guide de démarrage rapide 11 Figure 1 Contrôle du lecteur de bande Le lecteur de bande effectue un test d'autodiagnostic, appelé POST , chaque fois que vous l'allumez. 3 Pendant le test d'autodiagnostic, les voyants DEL s'allument les uns après les autres. Une fois le test d'autodiagnostic te ...

  • Quantum DLT-S4 - page 12

    Lecteur de bande DL T -S4 : Guide de démarrage rapide 12 Figure 4 Raccordement des câbles SCSI (connexion en chaîne) V alidation de l'installation 0 Procédez comme suit pour confirmer que l'installation est réussie : 1 Branchez le cordon d'alimen tation, puis allumez le lecteur de bande et l'ordinateur hôte. 2 Confirmez qu ...

  • Quantum DLT-S4 - page 13

    DLT-S4 テープ ドライブ クイック スタート ガイド 英語 - - - - - - - 1 ドイツ語 - - - - - 4 スペイン語 - - - - 7 フランス語 - - - - 10 日本語 - - - - - - 13 韓国語 - - - - - - 16 簡体字中国語 - - - 19 はじめに 0 このガイドではテープ ドライブの設置方法を説明します。 まず最? ...

  • Quantum DLT-S4 - page 14

    DLT-S4 テープ ドライブ クイック スタート ガイド 14 図 1 テープ ドライブの チェック 電源を入れる度に、テープ ドライブは 電源投入時の自己診 断テスト (POST) を実行します。 3 POST 実行中、各 LED が順に点灯します。 POST が問題 なく完了すると、中央の LED の? ...

  • Quantum DLT-S4 - page 15

    DLT-S4 テープ ドライブ クイック スタート ガイド 15 図 4 SCSI ケーブルの接続 ( デイジー チェーン ) 設置の確認 0 正しく設置されているかを確認するには、以下の手順に従い ます。 1 電源コードを接続し、テープ ドライブとホスト コン ピュータの電源を入れま? ...

  • Quantum DLT-S4 - page 16

    DLT-S4 테이프 드라이브 빠른 시작 안내서 영어 - - - - - - - - 1 독일어 - - - - - - - 4 스페인어 - - - - - - 7 프랑스어 - - - - - 10 일본어 - - - - - - 13 한국어 - - - - - - 16 중국어 ( 간체 ) - - - 19 시작하기 0 이 안내서는 테이프 드라이브를 설치하는 방법에 대해 설명합니다 . 시작 ...

  • Quantum DLT-S4 - page 17

    DLT-S4 테이프 드라이브 빠른 시작 안내서 17 테이프 드라이브는 사용자가 전원을 켤 때마다 전원 공급 자체 테스트 (POST) 라고 하는 자가 진단 테스트를 수행합니다 . 3 POST 도중 각 LED 표시등이 순서대로 켜집니다 . POST 가 성공적으로 완료되면 , 가운데 LED 가 깜박임을 ...

  • Quantum DLT-S4 - page 18

    DLT-S4 테이프 드라이브 빠른 시작 안내서 18 설치 확인 0 다음 단계들을 따라 설치가 성공적으로 완료되었는지 확인합 니다 . 1 전원 코드를 연결한 다음 , 테이프 드라이브와 호스트 컴 퓨터의 전원을 켭니다 . 2 시동 화면에 표시되는 BIOS, OS 및 SCSI 컨트롤러 정보 를 ? ...

  • Quantum DLT-S4 - page 19

    DLT-S4 磁带机 快速启动指南 英语 - - - - - - - 1 德语 - - - - - - - 4 西班牙语 - - - - - 7 法语 - - - - - - - 10 日语 - - - - - - - 13 朝鲜语 - - - - - - 16 简体中文 - - - - - 19 入门 0 本指南介绍磁带机安装说明。 开始： 1 检查运输箱和箱中的货物是否损坏。 如果您发现任何损坏情况? ...

  • Quantum DLT-S4 - page 20

    DLT-S4 磁带机 快速启动指南 20 3 通电自检过程中，顺序点亮每个指示灯。 当通电自检成 功完成后， 中间的 LED 停止闪烁并保持照亮， 左右边的 LED 关闭。 4 关闭磁带机并断开电源线和交流插座的连接。 连接磁带机 0 要连接磁带机： 1 务必关闭磁带机和主机电源。 2 ...

  • Quantum DLT-S4 - page 21

    DLT-S4 磁带机 快速启动指南 21 正在执行试用备份软件 0 为了 执 行试用备份： 1 将 数据 磁带插入磁带机 （ 请参阅 图 5 ） 。 确信您正在使用 DLTta pe S4 数据 盒 式 磁带。 图 5 插入 数据 盒 式 磁带 2 将磁带 慢慢推 入磁带机， 直 到磁带机自动装载介 质 。 磁 带机就 ...

  • Quantum DLT-S4 - page 22

    DL T -S4 T ape Drive Quick Start Guide For more information, visit quantum.com United States of America Quantum Corporation 141 Innovation Drive Irvine, CA 92617 U.S.A. phone 949.856.7800 fax 949.856.7799 European Headquarters Quantum Corporaton 3 Bracknell Beeches Old Bracknell Lane West Bracknell Berkshire RG12 7BW United Kingdom phone +44 1344 3 ...

Manufacturer Quantum Category Computer Drive

Documents that we receive from a manufacturer of a Quantum DLT-S4 can be divided into several groups. They are, among others:
- Quantum technical drawings
- DLT-S4 manuals
- Quantum product data sheets
- information booklets
- or energy labels Quantum DLT-S4
All of them are important, but the most important information from the point of view of use of the device are in the user manual Quantum DLT-S4.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Quantum DLT-S4, service manual, brief instructions and user manuals Quantum DLT-S4. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Quantum DLT-S4.

Similar manuals

A complete manual for the device Quantum DLT-S4, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Quantum DLT-S4 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Quantum DLT-S4.

A complete Quantum manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Quantum DLT-S4 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Quantum DLT-S4, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Quantum DLT-S4, that we can find in the current document
3. Tips how to use the basic functions of the device Quantum DLT-S4 - which should help us in our first steps of using Quantum DLT-S4
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Quantum DLT-S4
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Quantum DLT-S4 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Quantum DLT-S4?

Use the form below

If you did not solve your problem by using a manual Quantum DLT-S4, ask a question using the form below. If a user had a similar problem with Quantum DLT-S4 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)