English dropdown-ico

Manual Pelco MC3651H-2

12 pages 0.12 mb
Download

Go to site of 12

Summary
  • Pelco MC3651H-2 - page 1

    ® Installation/Operation MC3651H-2 Series DSP Monochr ome Camera C1985M-E (4/03) Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150 International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120 ...

  • Pelco MC3651H-2 - page 2

    [ 2 ] Pelco Manual C1985M-E (4/03) Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service and installation personnel. 2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approve ...

  • Pelco MC3651H-2 - page 3

    Pelco Manual C1985M-E (4/03) [ 3 ] CAMERA LA YOUT Figure 1. Camera Layout INST ALLA TION Lens Mounting The camera can use a fixed iris, manual iris, or auto iris. The camera is factory set for a CS-mount lens, but is easily adjusted for a C-mount lens. 1. C-Mount Lens Only - Rotate the back focus adjustment fully counterclockwise before install- in ...

  • Pelco MC3651H-2 - page 4

    [ 4 ] Pelco Manual C1985M-E (4/03) Power and Video Connections The MC3651H-2 camera is designed to operate from a 12 VDC or 24 V AC power supply . The power sup- ply connections are shown in Figure 1. The LED on the back panel of the camera indicates that power is connected. Use only a Class 2 isolated power supply . Power consumption is less than ...

  • Pelco MC3651H-2 - page 5

    Pelco Manual C1985M-E (4/03) [ 5 ] To connect the camera power and video: 1. Remove the cosmetic trim ring from the camera (refer to Figure 1). Thread cabling through the rear cover . 2. Connect the power cable to the two pin power connector on the back of the camera using the terminal block connector (provided). Refer to T able A for the recommend ...

  • Pelco MC3651H-2 - page 6

    [ 6 ] Pelco Manual C1985M-E (4/03) LENS SETUP AND FOCUS PROCEDURES V ideo Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video out- put level of 1V peak-to-peak). Switch the AGC ...

  • Pelco MC3651H-2 - page 7

    Pelco Manual C1985M-E (4/03) [ 7 ] Figure 5. Back Focus Adjustment BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. T urn the back focus ring until the object is in focus. ...

  • Pelco MC3651H-2 - page 8

    [ 8 ] Pelco Manual C1985M-E (4/03) Figure 6. Default Settings OFF OFF OFF OFF AIV INT NOR OFF OFF OFF BLC AGC OPT ESC AID LL SHP LC DS1 DS2 ON PHASE LEVEL + - H L 1 2 3 4 5 6 7 8 9 10 00026 1 BLC - Back Light Compensation OFF (Default setting) - Disables the BLC mode. BLC - Enables the BLC mode. If a bright backlight is present the subjects in the ...

  • Pelco MC3651H-2 - page 9

    Pelco Manual C1985M-E (4/03) [ 9 ] 7 NOR/SHP - Sharpness NOR (Default setting) - Sets the camera to normal sharpness mode. SHP - Enables the Sharpness mode. Enhances picture detail by increasing the aperture gain of the camera, sharpening the edges in the picture. 8 LC - Long Line Compensation OFF (Default setting) - Disables the Long Line Compensa ...

  • Pelco MC3651H-2 - page 10

    [ 10 ] Pelco Manual C1985M-E (4/03) CAMERA SYNCHRONIZA TION (AC OPERA TION ONL Y) When using more than one camera power supply , a brief vertical roll may occur on the monitor each time a camera view is switched. T o eliminate vertical roll, adjust the phase control by synchronizing, or line- locking, the cameras to one another . Use the phase pote ...

  • Pelco MC3651H-2 - page 11

    Pelco Manual C1985M-E (4/03) [ 11 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch interline transfer Picture Elements MC3651H-2: 768 (H) x 494 (V) MC3651H-2X: 795 (H) x 596 (V) Sensing Area: 6 mm diagonally Synchronize System: INT/AC line lock Horizontal Resolution 570 TV lines Iris Control: Electronic/passive Minimum Illumination 0.0035 lux at f1.2 ...

  • Pelco MC3651H-2 - page 12

    [ 12 ] Pelco Manual C1985M-E (4/03) REVISION HISTOR Y Manual # Date Comments C1985M 10/00 Original version. C1985M-A 12/00 Added note for cosmetic trim ring. Revised switch setting illustration to depict default settings. C1985M-B 7/01 Added camera model MC3651H-2X. C1985M-C 6/02 Revised the lens connector wiring chart. C1985M-D 8/02 Revised the Di ...

Manufacturer Pelco Category Digital Camera

Documents that we receive from a manufacturer of a Pelco MC3651H-2 can be divided into several groups. They are, among others:
- Pelco technical drawings
- MC3651H-2 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco MC3651H-2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco MC3651H-2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco MC3651H-2, service manual, brief instructions and user manuals Pelco MC3651H-2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco MC3651H-2.

Similar manuals

A complete manual for the device Pelco MC3651H-2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco MC3651H-2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco MC3651H-2.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco MC3651H-2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco MC3651H-2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco MC3651H-2, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco MC3651H-2 - which should help us in our first steps of using Pelco MC3651H-2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco MC3651H-2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco MC3651H-2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco MC3651H-2?

Use the form below

If you did not solve your problem by using a manual Pelco MC3651H-2, ask a question using the form below. If a user had a similar problem with Pelco MC3651H-2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)