English dropdown-ico

Manual Home Automation RC-80BZ

16 pages 0.26 mb
Download

Go to site of 16

Summary
  • Home Automation RC-80BZ - page 1

    1 1 RC-80BZ Single Stage Heat/C ool Thermostat Installation Ins tructions DESCRIPTION The RC-80BZ is a precision digital ther mostat designed for 24 VAC single stage heating and cooling systems. It has the capability of being controlled both locally and by remote c ontrol over a Z-Wave network. It offe rs programmability, stand-alone operation, and ...

  • Home Automation RC-80BZ - page 2

    2 2 Removing an existing thermostat 1. Disconnect the power to the control transformer. 2. Remove the cover to the existing thermosta t. 3. Disconnect the wires going to ea ch terminal on the thermostat. Label eac h wire with the letter or number at the terminal. 4. Remove the existing plate or base from the wall. MOUNTING When mounting the RC-80BZ ...

  • Home Automation RC-80BZ - page 3

    3 3 Connect each wire to the terminal strip on the ther mostat base per the wiring diagram for your system application - See Figures 4 - 8. Form the thermostat wiri ng so that the cable lies flat between the terminal strip a nd the center of the base. Upon completion of wiring the thermostat, push all excess wi ring into the hole in the wall. Plug ...

  • Home Automation RC-80BZ - page 4

    4 4 TYPICAL WIRING DIAGRAMS CAUTION: Be sure to disconnect the power to the control transformer before removing or installing thermostat. Do not short gas valve, fan, heat relay, or cool relay... even momentarily. This w ill blow a non-replaceable fuse. Do not attempt to hook up to live circuits. An accidenta l connection to a component on the ther ...

  • Home Automation RC-80BZ - page 5

    5 5 Common wire is required in “cool only” applications Figure 6 - Single stage cool only thermostat * Common wire is required to use t he display backlig ht in the RC-80ZB. Also use if heat, cool, or fan relay cannot supply 15mA to power thermostat, without activating. Figure 7 - Single stage heat/cool thermostat ...

  • Home Automation RC-80BZ - page 6

    6 6 * Do not connect RC and RH together. Figure 8 - Heating & cooling with separate transformers CONFIGURING THE BACKLIGHT ON THE RC-80ZB The backlight on the RC-80ZB can be configured to one of three different modes: 1) on for 30 seco nds when a key is pressed, 2) always on, or 3) always off. 1) To configure the display backlight to turn on wh ...

  • Home Automation RC-80BZ - page 7

    7 7 SOLDER WIRE JUMPER HERE SELECT BACKLIGHT MODE (SET JUMPER) TO DISABLE KEYS LOCALLY Figure 9 POWER UP 1. Double check wiring, be sure that there are no stray wires or wire strands at the connections. 2. Connect power to the transformer and system. The di splay will show all segments for about 5 seconds. 3. Press the Fan key. The fan should come ...

  • Home Automation RC-80BZ - page 8

    8 8 INSTALLER SETUP This section describes the items that th e installer must setup as part of the thermostat installation. The Installer Setup mode is used to configure the genera l operating parameter s of the thermostat. When in Installer Se tup mode: 1. The small digits on the top of the display are the item number. 2. The large blinking digits ...

  • Home Automation RC-80BZ - page 9

    9 9 00 Address If you are using Communications Mode 0 or 1, and you ar e installing more than one thermosta t, each must be set to a consecutive address, starting at 1. The default address setting is 1. An address from 1- 127 may be selected. 01 Communications mode The thermostat can communicat e with remote systems in 4 di fferent modes. These mod ...

  • Home Automation RC-80BZ - page 10

    1 1 0 0 04 Calibration offset This item is used to raise or lower the current temperature reading by 1 degree Fahrenheit or 1/2 degree Celsius. If this item is set to 30, no change w ill be made. Each di git below 30 will lower to temperature, an d each digit above 30 will raise the temperature. (1 = “- 29” to 59 = “+ 29” temperature units; ...

  • Home Automation RC-80BZ - page 11

    1 1 1 1 10 Heating anticipator This item adjusts the tendency of the thermostat to turn the heating unit off before the de sired heat setting is reached. This is done to avoid overheatin g the air while the walls and furniture cat ch up. A setting of 0 will disable this feature. 0 No anticipation 3-5 Normal anticipation 10 Maximum anticipation The ...

  • Home Automation RC-80BZ - page 12

    1 1 2 2 14 Clock adjust If the clock on the thermostat is running faster or sl ower than the actu al time, you can have the thermostat automatically compensate up to 29 seconds per day. The thermostat will add or subtr act the selected amount of time daily. (1 = “- 29” to 59 = “+ 29” seconds per da y; 30 = No change) The default setting is ...

  • Home Automation RC-80BZ - page 13

    1 1 3 3 QUICK-REFERENCE SETUP GUIDE This table displays each Installer Setup ite m with its default setting. The column labeled "CURRENT" can be used to write down the current setting s if any changes are made to the default settings. Item Number Description Def ault Current 00 Address 1 01 Communication mode 1 02 Sy stem options 0 03 Dis ...

  • Home Automation RC-80BZ - page 14

    1 1 4 4 The thermostat suppor ts the following command c lasses: COMMAND_CLASS_THE RMOSTAT_MODE COMMAND_CLASS_TH ERMOSTAT_SETPO INT COMMAND_CLASS_THE RMOSTAT_FAN_M ODE COMMAND_CLASS_TH ERMOSTAT_FAN_ STATE COMMAND_CLASS_TH ERMOSTAT_OPERAT ING_STATE COMMAND_CLASS_SENSOR_M ULTILEVEL COMMAND_CLASS_ASSO CIATION COMMAND_CLASS_CONFIGURAT ION COMMAND_CLASS ...

  • Home Automation RC-80BZ - page 15

    1 1 5 5 COMMAND_CLASS_THE RMOSTAT_OPERATING_STATE Upon power up, allow 10 seconds for the RC-80BZ thermost at to initialize. After 10 seconds, a controller can request the Operatin g State report. COMMAND_CLASS_VERSION Upon power up, allow 10 seconds for the RC-80BZ thermost at to initialize. After 10 seconds, a controller can request a Version Rep ...

  • Home Automation RC-80BZ - page 16

    1 1 6 6 TROUBLESHOOTING TIP S SYMPTOM ACTION TO TAKE 1. Check power to the therm ostat 2. Check wiring diagrams Thermostat Dead 3. Check thermostat temper ature sensor Thermostat will not operate with a damage d temperature sensor. SYMPTOM ACTION TO TAKE 1. Check for break in G, W, or Y wire 2. Allow minimum off time to pass 3. Check system options ...

Manufacturer Home Automation Category Thermostat

Documents that we receive from a manufacturer of a Home Automation RC-80BZ can be divided into several groups. They are, among others:
- Home Automation technical drawings
- RC-80BZ manuals
- Home Automation product data sheets
- information booklets
- or energy labels Home Automation RC-80BZ
All of them are important, but the most important information from the point of view of use of the device are in the user manual Home Automation RC-80BZ.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Home Automation RC-80BZ, service manual, brief instructions and user manuals Home Automation RC-80BZ. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Home Automation RC-80BZ.

Similar manuals

A complete manual for the device Home Automation RC-80BZ, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Home Automation RC-80BZ by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Home Automation RC-80BZ.

A complete Home Automation manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Home Automation RC-80BZ - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Home Automation RC-80BZ, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Home Automation RC-80BZ, that we can find in the current document
3. Tips how to use the basic functions of the device Home Automation RC-80BZ - which should help us in our first steps of using Home Automation RC-80BZ
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Home Automation RC-80BZ
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Home Automation RC-80BZ in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Home Automation RC-80BZ?

Use the form below

If you did not solve your problem by using a manual Home Automation RC-80BZ, ask a question using the form below. If a user had a similar problem with Home Automation RC-80BZ it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)