English dropdown-ico

Manual Meyer Sound PSM-2

10 pages 0.36 mb
Download

Go to site of 10

Summary
  • Meyer Sound PSM-2 - page 1

    The PSM-2 self-powered stage monitor contains i ndependent amplifier and control electronics for one 12” cone driver and one 4” diaphragm horn driver in a compact enclosure. This integrated design eliminates amplifier racks, improves durability and reliability, and simplifies setup and installation. The PSM-2 can be oriented such that the plane ...

  • Meyer Sound PSM-2 - page 2

    2 According to ISO/IEC Guide and EN 45014 The product herewith complies with the require- ments of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC. declares that the product: The Manufacturer: Product Name : PSM-2 Product Options : All Name : Meyer Sound Laboratories Address : 2832 San Pablo Avenue Berkeley, California 94702-22 ...

  • Meyer Sound PSM-2 - page 3

    3 ATENCIÓN : ACCESO INTER AUTORIZADO A PERSONAL TÉ ACHTUNG : GEHÄUSE NICHT UND REPARATUR NUR DURCH ATTENTION : ENTRETIEN ET INTERNES NE SONT AUTORIU PERSONNEL TECHNIQUE QUA UK WARNING : THIS APPAR NO OPERATOR SERVICEABLE PA REFER SERVICING TO QUALIFIED WARNINGS: THIS PRODUCT M This surface may reach high t To ensure proper operation, allow clear ...

  • Meyer Sound PSM-2 - page 4

    4 AC Power The AC voltage operating ranges for the PSM-2 are 85–134 V and 165–264 V, at 50 or 60 Hz. The PSM-2 performs surge suppression for high voltage transients and can safely withstand voltages up to 275 VAC. Continuous voltages above 275 VAC may damage the unit! When an AC source is applied to the PSM-2, the Intelligent AC power supply ? ...

  • Meyer Sound PSM-2 - page 5

    5 Differential Inputs Audio Input The PSM-2 presents a 10 k Ω input impedance to a three- pin XLR connector wired with the following convention: Pin 1 — 220 k Ω to chassis and earth ground (ESD clamped) Pin 2 — Signal Pin 3 — Signal Case — Earth (AC) ground and chassis Pins 2 and 3 carry the input as a differential signal; their polarit ...

  • Meyer Sound PSM-2 - page 6

    6 Limiting and Protection Circuitry TruPower Limiting System Conventional limiters assume that the resistance of a speaker remains constant and set the limiting threshold by measuring voltage only. This method is inaccurate because the speaker’s resistance changes in response to the frequency content of the source material and thermal variations ...

  • Meyer Sound PSM-2 - page 7

    7 The fans draw air in through ducts on the front of the cabinet, over the heatsinks, and out the rear of the cabinet. Since dust does not accumulate in the ampli fier circuitry, its life span is increased significantly. Make sure that the air ducts are clear and that there is at least 6” clearance for exhaust behind the cabinet. air air cooling ...

  • Meyer Sound PSM-2 - page 8

    8 PSM-2 and PSW-2 The PSM-2 can be used with the Meyer PSW-2, PSW-4, or 650-P self-powered subwoofers. However, due to the overlap of frequency response between the PSM-2 and th e subwoofer, the system frequency response exhibits a rise in the range 50–120 Hz. The rise can be eliminated by the Meyer CP-10 Parametric Equalizer , if desired. In a c ...

  • Meyer Sound PSM-2 - page 9

    9 • To reduce the risk of electric shock, disconnect the loudspeaker from the AC mains before installing audio cable. Reconnect the power cord only after making all signal connections. • Connect the loudspeaker to a two-pole, three wire grounding mains receptacle. The receptacle must be connected to a fuse or circuit breaker. Connection to any ...

  • Meyer Sound PSM-2 - page 10

    10 Complementary power MOSFET output stages class AB/H 1240 Watts (620 Watts per channel) < .02 % Acoustical Copyright © 1997, Meyer Sound Laboratories, Inc. All rights reserved Part #: 05.044.012.01 Rev A ± 4 dB 50 Hz – 18 kHz ± 90 ° 200 Hz – 16 kHz 139 dB peak at 1 m > 110 dB –6 dB: 50 ° H x 50 ° V; –10 dB: 70 ° H x 70 ° V S ...

Manufacturer Meyer Sound Category Portable Speaker

Documents that we receive from a manufacturer of a Meyer Sound PSM-2 can be divided into several groups. They are, among others:
- Meyer Sound technical drawings
- PSM-2 manuals
- Meyer Sound product data sheets
- information booklets
- or energy labels Meyer Sound PSM-2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Meyer Sound PSM-2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Meyer Sound PSM-2, service manual, brief instructions and user manuals Meyer Sound PSM-2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Meyer Sound PSM-2.

Similar manuals

A complete manual for the device Meyer Sound PSM-2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Meyer Sound PSM-2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Meyer Sound PSM-2.

A complete Meyer Sound manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Meyer Sound PSM-2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Meyer Sound PSM-2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Meyer Sound PSM-2, that we can find in the current document
3. Tips how to use the basic functions of the device Meyer Sound PSM-2 - which should help us in our first steps of using Meyer Sound PSM-2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Meyer Sound PSM-2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Meyer Sound PSM-2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Meyer Sound PSM-2?

Use the form below

If you did not solve your problem by using a manual Meyer Sound PSM-2, ask a question using the form below. If a user had a similar problem with Meyer Sound PSM-2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)