English dropdown-ico

Manual Vivitek Q7 Plus

65 pages Not applicable
Download

Go to site of 65

Summary
  • Vivitek Q7 Plus - page 1

    ...

  • Vivitek Q7 Plus - page 2

    ii Preface Copyright ©2014 Vivitek Corporation. is a trademark of Vivitek Corporation. Other trademarks are the properties of their respective owners. V alues, weights and dimensions are approximate. Specications are subject to change without prior notice. Disclaimer The information in this document is subject to change without notice. The manu ...

  • Vivitek Q7 Plus - page 3

    iii Important Safety Information Important: It is strongly recommended that you read this section carefully before using the Qumi. These safety and usage instructions that will make sure you enjoy many years of safe use of the Qumi. Keep this manual for future reference. Symbols Used W arning symbols are used on the unit and in this manual to alert ...

  • Vivitek Q7 Plus - page 4

    iv Qumi Installation Notice • Allow at least a 50cm clearance around the exhaust vent. Minimum 100mm Minimum 500mm • Make sure that the intake vents do not recycle hot air from the exhaust vent. • When operating the Qumi in an enclosed space, make sure that the surrounding air temperature within the enclosure does not exceed operating tempera ...

  • Vivitek Q7 Plus - page 5

    v Power Safety • Only use the supplied power cord. • Do not place anything on the cord. Place the cord where it will not be in the way of foot trafc. • Remove the battery from the remote control when storing or not in use for a prolonged period. Cleaning the Qumi • Unplug the cord before cleaning. See Cleaning the Qumi on page 47 . Note: ...

  • Vivitek Q7 Plus - page 6

    vi T able of Contents Preface .................................................................................................................. ii Chapter 1 At a Glance ................................................................ 1 Overview ........................................................................................................ ...

  • Vivitek Q7 Plus - page 7

    1 Chapter 1 At a Glance Overview Front/T op/Right View Keypad Keypad See Keypad - On-Screen Display (OSD) buttons Cooling Vent Do not cover Lens Projection Lens Zoom / Focus ring Zoom / Focus the projected image Cooling Vent Do not cover Right Cursor Navigate and change settings in the OSD Enter Cursor Change settings in the OSD Left Cursor Navigat ...

  • Vivitek Q7 Plus - page 8

    2 Rear/T op/Left View Bottom View AC In Connect the supplied power cord Audio Out Connect an audio cable to speakers or headphones Audio in (L&R) Connect the Audio in (L&R) cable from an audio device Video Connect the video cable from a video device VGA Connect the VGA cable from a VGA device IR Receiver Receive IR signal from the remote co ...

  • Vivitek Q7 Plus - page 9

    3 Standard Accessories Along with the Qumi, the following accessories are included: Remote Control (With one 3V CR2025 battery) Standard HDMI Cable VGA Cable MHL cable Regional Power Cord WA RRAN TY Documentation Kit (User Manual, Quick Start Guide, W arranty Card) Lens Cap Optional Accessories Carrying Case WiFi Dongle Contact your dealer immediat ...

  • Vivitek Q7 Plus - page 10

    4 Remote Control Important: 1. Be sure nothing obstructs the path between the remote control and the Qumi. If the path between the remote control and the Qumi is obstructed, the signal can bounce off certain reective surfaces. 2. The buttons and keys on the Qumi have the same layout and similar functions as the corresponding buttons on the remot ...

  • Vivitek Q7 Plus - page 11

    5 Media Player Screen The media player screen is the main interface for the Qumi Q7 Plus Series. If a USB Flash Disc is plugged in when powering on the Qumi, the media player screen appears. In the media player screen, you can choose the type of media to display by selecting: • Music – A music player that supports many types of audio les, re ...

  • Vivitek Q7 Plus - page 12

    6 Chapter 2 Getting Started What Y ou Need Many types of external devices and peripherals can be connected to the Qumi. External or portable music players can be connected to play music. DVD, VCD and VHS players can be connected to play movies. Camcorders and digital cameras can also be used to play videos and display photos. Computers can be conne ...

  • Vivitek Q7 Plus - page 13

    7 Setting Up Qumi Connecting to an HDMI Device Connect your Qumi to an HDMI device by using an HDMI cable. USB HDMI 1 / MHL HDMI 2 VG A VIDEO AU DIO OUT L - AU DIO - R K Game Console Personal Computer Smartphone Camera Blue Ray DVD player Connecting to an MHL Device Connect your Qumi to a MHL-compatible device by using an MHL cable. USB HDMI 1 / MH ...

  • Vivitek Q7 Plus - page 14

    8 Inserting a USB Flash Disc Connect a USB Flash Disc to the Qumi by inserting the storage device(s) into the appropriate port. USB HDMI 1 / MHL HDMI 2 VG A VIDEO AU DIO OUT L - AU DIO - R K Connecting Video Connect audio/video devices to the Qumi by using the audio/video cable. USB HDMI 1 / MHL HDMI 2 VG A VIDEO AU DIO OUT L - AU DIO - R K Game Co ...

  • Vivitek Q7 Plus - page 15

    9 Starting and Shutting down the Qumi 1. Connect the AC power cord to the Qumi. Connect the other end of the AC power cord to a wall outlet. 2. Press the POWER button to turn on the Qumi. The Qumi splash screen displays and connected devices are detected. See Setting an Access Password (Security Lock) on page 1 1 if security lock is enabled. 3. If ...

  • Vivitek Q7 Plus - page 16

    10 4. Press the POWER button to turn off the Qumi. 5. When the “Power Off? /Press Power again” message appears, press the POWER button. The projector turns off. Adjusting the Image Use the Image-zoom control (on the projector) to resize the projected image and screen size (B). B A Use the Image-focus control (on the projector) to sharpen the pr ...

  • Vivitek Q7 Plus - page 17

    11 Setting an Access Password (Security Lock) T o prevent unauthorized use of the Qumi, you can create a password. When the access password function is enabled, the password must be entered after the Qumi has been turned on. Creating a password can be done by performing the following steps: 1. Press the MENU button on the remote control or press ME ...

  • Vivitek Q7 Plus - page 18

    12 6. The password conrmation menu appears when you power on the Qumi when the Security Lock is enabled. Enter the password that was created in step 5. Important: Keep the password in a safe place. Without the password, you will not be able to use the Qumi. If you lose the password, contact your reseller for information on resetting the password ...

  • Vivitek Q7 Plus - page 19

    13 Setting Up the Remote Control The remote control comes with one (1) 3V lithium battery (CR2025). The battery is pre-installed in the remote control. T o begin using the remote control, remove the plastic tab (A) from the battery compartment. A Replacing the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover tow ...

  • Vivitek Q7 Plus - page 20

    14 Chapter 3 Qumi Media Suite Overview The Qumi Media Suite is designed to provide easy access to your les from an inserted USB Flash Disc. Music, movies, pictures and documents can be displayed. The media suite menu contains 8 applications that can be accessed: • Music – A music player that supports many types of audio les, ready to play ...

  • Vivitek Q7 Plus - page 21

    15 Music Supported Formats: The music player can play music les in the following formats: • MP3 (up to 256Kbps bit-rate) • WMA, MID, MIDI, MP1, MP2, OGG, AAC, AMR, W A V , AC3, M4A, A WB, APE Playing your T rack T o open the music list, perform the following: 1. Press the ◄ or ► button to select the Music icon in the media suite menu. 2. ...

  • Vivitek Q7 Plus - page 22

    16 The music player provides controls to navigate through a song playlist. The following table provides a description the controls. ACTION DESCRIPTION / / T oggle speaker output to Left/Right/Stereo / Return to previous/Forward to next track / Pause/Play track Stop playback Return to the previous menu The order of songs and playback mode can be adj ...

  • Vivitek Q7 Plus - page 23

    17 Movies Supported Formats The following video formats are supported: • H.264 video up to 720p at 30 frames per second; Main Prole level 3.1 with AAC-LC audio up to 160 Kbps, 48kHz, stereo audio in .m4v , .mp4, and .mov le formats • MPEG-4 video up to 2.5 Mbps, 640 by 480 pixels at 30 frames per second; Simple Prole with AAC-LC audio ...

  • Vivitek Q7 Plus - page 24

    18 Photos Supported Formats The photo viewer can open the following types of image les: • BMP (up to 4000 x 3000 pixels) • PNG (up to 4000 x 3000 pixels) • JPG (up to 4000 x 3000 pixels) Viewing Y our Photo When a USB Flash Disc is inserted, the Flash Disc folder icon will display in the le directory . T o open a photo in photo viewer , ...

  • Vivitek Q7 Plus - page 25

    19 Ofce V iewer Supported Formats The document viewer in the Qumi Media Suite can open the following types of documents: • Microsoft ® Word (97-2007, .doc/.docx) • Microsoft ® PowerPoint (97-2007, .ppt/.pptx) (not support Animation and slide transitions) • Microsoft ® Excel (97-2007, .xls/.xlsx) • Adobe ® PDF (.pdf) (PDF 1.0, 1.1, 1. ...

  • Vivitek Q7 Plus - page 26

    20 Wi T urning on WiFi Insert the Q7 Plus WiFi dongle in the Qumi to surf the Web through a web browser . T o turn on WiFi, perform the following: 1. Press the ◄ or ► button to select the Wi icon in the media suite menu. 2. Press to enter Network Settings. • Device Name / SSID: Enter the Service Set Identier here. • WiFi: Enable Wi ...

  • Vivitek Q7 Plus - page 27

    21 WiFi Control Interface The WiFi Setting contains the following controls: ACTION DESCRIPTION Return to Main Window . / Enable/Disable WiFi. WiFi conguration. ...

  • Vivitek Q7 Plus - page 28

    22 WiFi Congure The WiFi Congure setting lets you setup a dynamic (Default) or static IP connection. ACTION DESCRIPTION IP Address Congure the IP address of the projector here. Netmask Congure the subnet mask here. Gateway Congure the IP address of the default gateway here. DNS Congure the IP address of the DNS server here. WiFi h ...

  • Vivitek Q7 Plus - page 29

    23 W eb browser Visiting a website 1. Plug the Q7 Plus Wi-Fi Dongle into Qumi’s USB socket. 2. Press ▲ ▼ ◄ ► on the remote control to control the cursor . See Remote Control on page 4 . 3. Use the remote control for navigation control. Press the Q icon (bottom-right) to access the address bar . 4. Press to display the virtual keyboard, or ...

  • Vivitek Q7 Plus - page 30

    24 Wi Display Set Wi Display 1. Plug the Q7 Plus Wi-Fi Dongle into Qumi’s USB socket. 2. Set Network settings > Wi to Enabled and Wi hotspot to Enabled. 3. Press the ◄ or ► button to select the Wi Display icon in the media suite menu. ...

  • Vivitek Q7 Plus - page 31

    25 Settings System Options The system options menu displays the system and rmware information. The Information menu provides details about the software version. Play Mode The play mode menu displays settings for both video and music player options. The following settings are available: • Repeat None – The videos or music tracks will not repe ...

  • Vivitek Q7 Plus - page 32

    26 AutoPlay Option Use the AutoPlay Option menu to congure what the Qumi automatically plays when powered on. The following settings are available when AutoPlay is ON. • AutoPlay – T urn on or off auto play . • AutoPlay T ype – Automatically play photo or video les when powered on. • File Path – Automatically play les in the ro ...

  • Vivitek Q7 Plus - page 33

    27 Chapter 4 On-Screen Display (OSD) Settings OSD Menu Controls The Qumi has an On-Screen Display (OSD) settings menu that allows you to make adjustments and changes to settings, such as display settings and audio settings. There are 3 menus within the OSD menu: • Image – V arious aspects of the image quality can be adjusted in this menu. • S ...

  • Vivitek Q7 Plus - page 34

    28 Setting the OSD Language The language that is displayed in the OSD can be changed. T o change the language in the OSD, perform the following steps: 1. Enter the OSD menu. Press the ◄ or ► button to select the Setting 1 and press . 2. Press the ▲ or ▼ button to move to the Advanced 1 menu. 3. Press to enter the Advanced 1 sub menu. 4. Pre ...

  • Vivitek Q7 Plus - page 35

    29 OSD Menu Overview Use the following illustration to quickly nd a setting or determine the range for a setting. MAIN MENU SUB MENU SETTINGS Image Display Mode Presentation, Bright, Game, Movie, TV , sRGB, User , User1 Brightness 0~100 Contrast 0~100 Computer Horizontal Position -5~5 V ertical Position -5~5 Frequency 0~31 T racking -5~5 Auto Im ...

  • Vivitek Q7 Plus - page 36

    30 MAIN MENU SUB MENU SETTINGS Settings 1 Source Reference Input Source Select (IR/Keypad) Projection Normal, Real, Ceiling, Real+Ceiling Aspect Ratio Fill, 4:3, 16:9, Letter Box, Native, 2.35:1 Keystone -40~40 Digital Zoom -10~10 Audio V olume 0~10 Mute Off, On Advanced 1 Language English, Français, Deutsch, Español, Português, 簡体 中文 , ...

  • Vivitek Q7 Plus - page 37

    31 MAIN MENU SUB MENU SETTINGS Settings 2 Auto Source Off, On No Signal Power Off (min) 0~180 Auto Power On Off, On Off, On LED Mode ECO , Normal Reset All Status Active Source Video Information LED Hours(Eco., Normal) Software V ersion Advanced 1 Menu Position Center , Down, Up, Left, Right T ranslucent Menu 0%, 25%, 50%, 75%, 100% Low Power Mode ...

  • Vivitek Q7 Plus - page 38

    32 Image Menu T o access the Image menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move the cursor up or down in the Image menu and press . 4. Press the ◄ or ► button to change values for each applicable setting. ITEM DES ...

  • Vivitek Q7 Plus - page 39

    33 Computer T o access the Computer menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move to the Computer menu and press . 4. Press the ◄ or ► button to change values for each applicable setting. ITEM DESCRIPTION Horizonta ...

  • Vivitek Q7 Plus - page 40

    34 Advanced T o access the Advanced menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move to the Advanced menu and press . 4. Press the ▲ or ▼ button to move the cursor up or down in the Advanced menu. ITEM DESCRIPTION Bri ...

  • Vivitek Q7 Plus - page 41

    35 Color Manager T o access the Color Manager menu and adjust the settings, perform the following: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move the cursor up or down in the Color Manager menu and press . 4. Press the ◄ or ► button to change values for each applicable sett ...

  • Vivitek Q7 Plus - page 42

    36 Settings 1 Menu T o access the Settings 1 menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 1 menu. 3. Press the ▲ or ▼ button to move the cursor up and down in the Settings 1 menu and press . 4. Press the ◄ or ► button to change values for each applica ...

  • Vivitek Q7 Plus - page 43

    37 Audio T o adjust the audio settings, press to enter the Audio sub menu. ITEM DESCRIPTION V olume Press the ◄ or ► button to adjust the audio volume. Mute Press the ◄ or ► button to turn on or off the speaker . ...

  • Vivitek Q7 Plus - page 44

    38 Advanced 1 T o adjust the advanced settings, press to enter the Advanced 1 sub menu. ITEM DESCRIPTION Language Press the ◄ or ► button to select a different localization menu. Security Lock Press the ◄ or ► button to enable or disable security lock function. Blank Screen Press the ◄ or ► button to select different color to blank the ...

  • Vivitek Q7 Plus - page 45

    39 3D Setting T o adjust the 3D settings, press to enter the 3D Setting sub menu. ITEM DESCRIPTION 3D Press the ◄ or ► button to select Off, DLP-Link or IR. 3D Sync Invert Press the ◄ or ► button to turn 3D sync Invert on or off. 3D Format Press the ◄ or ► button to select Frame Sequential, T op / Bottom, Side by Side. 2Dto3D Press the ...

  • Vivitek Q7 Plus - page 46

    40 Advanced 2 T o adjust the advanced settings, press to enter the Advanced 2 sub menu. ITEM DESCRIPTION T est Pattern Press the ◄ or ► button to select different test pattern. H Image Shift Press the ◄ or ► button to shift the horizontal position. V Image Shift Press the ◄ or ► button to shift the vertical position. ...

  • Vivitek Q7 Plus - page 47

    41 Settings 2 Menu T o access the Settings 2 menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to move the cursor up and down in the Settings 2 menu and press . 4. Press the ◄ or ► button to change values for each applica ...

  • Vivitek Q7 Plus - page 48

    42 Reset All T o reset all of the menu items to the factory default values (except Language and Security Lock), perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to select the Reset All menu and press . ...

  • Vivitek Q7 Plus - page 49

    43 Status T o see the status of the Qumi, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to select the Status menu and press . ITEM DESCRIPTION Active Source Displays the activated source. Video Information Displays resolution/video information for RGB ...

  • Vivitek Q7 Plus - page 50

    44 Advanced 1 T o access the Advanced 1 menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to select the Advanced 1 menu and press . 4. Press the ▲ or ▼ button to move the cursor up or down in the Advanced 1 menu. 5. Press ...

  • Vivitek Q7 Plus - page 51

    45 Advanced 2 T o access the Advanced 2 menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to select the Advanced 2 menu and press or ►. 4. Press the ▲ or ▼ button to move the cursor up or down in the Advanced 2 menu. 5. ...

  • Vivitek Q7 Plus - page 52

    46 Source Filter T o adjust the source lter , press or ► to enter the Source Filter sub menu. ITEM DESCRIPTION VGA Press the ◄ or ► button to enable or disable VGA source in auto search loop. Composite Video Press the ◄ or ► button to enable or disable Composite Video source in auto search loop. HDMI 1 / MHL Press the ◄ or ► button ...

  • Vivitek Q7 Plus - page 53

    47 Chapter 5 T aking Care of Y our Qumi Cleaning the Qumi Cleaning the Qumi to remove dust and grime will help provide trouble-free operation. Warning: 1. The Qumi should be turned off and unplugged before cleaning. Failure to do so may result in injury or damage to the system. 2. Use only a dampened cloth when cleaning. Do not allow water to enter ...

  • Vivitek Q7 Plus - page 54

    48 T roubleshooting Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the Qumi. If the problem remains unresolved, contact your dealer for assistance. The problem sometimes can be as simple as a wire that is not completely connected. Review the following possible issues before proceeding ...

  • Vivitek Q7 Plus - page 55

    49 LED Error Messages ERROR CODE MESSAGES POWER BLUE BLINK TEMP BLUE BLINK Over temperature error (Inlet air ) - ON LED over temperature (Red) - 1 LED over temperature (Green) - 2 Fan 1 (Power) error 6 1 Fan 2 (System) error 6 2 Fan 3 (LED) error 6 3 Red LED Thermistor error 8 1 Green LED HSK Thermistor error 8 2 In the event of an LED error , disc ...

  • Vivitek Q7 Plus - page 56

    50 Problem: The image is at with no contrast Adjust the Contrast setting in the Image menu in the OSD. Problem: The color of the projected image does not match the source image Adjust the Color T emperature and Gamma settings in the Image menu in the OSD. Remote Control Problems Problem: The Qumi does not respond to the remote control 1. Aim the ...

  • Vivitek Q7 Plus - page 57

    51 F AQs 1. Does Qumi work with a personal computer , notebook or netbook? Y es. Use the provided VGA cable or HDMI cable. The Qumi can connect to a PC, notebook or netbook if they have an appropriate HDMI or VGA port. T o play audio, a stereo audio cable is required to connect to the Qumi’s audio port. 2. Is it possible to connect the Qumi to a ...

  • Vivitek Q7 Plus - page 58

    52 10. What type of photo formats does the QUMI support? JPEG, PNG and BMP . 1 1. How long will the LED light source in the Qumi last and can it be replaced? The Qumi does not use a typical UHP lamp. It uses a set of Light Emitting Diodes (LED) to illuminate and project images. LED’s have a greater lifespan than conventional lamps. Qumi LED’s a ...

  • Vivitek Q7 Plus - page 59

    53 Specications MODEL Qumi Q7 Plus Series RESOLUTION HD (WXGA - 1280x800) PROJECTION DIST ANCE 0.8m~3.0m PROJECTION SCREEN SIZE (DIAGONAL) 26”~107.1” PROJECTION LENS Manual focus and Zoom THROW RA TIO 1.3/1.43 : 1 VERTICAL KEYST ONE CORRECTION +40 step = 32° -40 step = -35° PROJECTION METHODS Front, Rear , Desktop, Front-Ceiling, Rear-Ceil ...

  • Vivitek Q7 Plus - page 60

    54 Projection Distance vs. Projection Size Projection Distance and Size T able @WIDE IMAGE DIAGONAL (CM/INCHES) IMAGE WIDTH (CM/INCHES) IMAGE HIGH (CM/INCHES) PROJECTION DIST ANCE (CM/INCHES) 72.6 / 28.6 61.5 / 24 38.5 / 15 80 / 31 101.6 / 40 86.2 / 34 53.8 / 21 1 12 / 44 127 / 50 107.7 / 42 67.3 / 26 140 / 55 152.4 / 60 129.2 / 51 80.8 / 32 168 / ...

  • Vivitek Q7 Plus - page 61

    55 T iming Mode T able SIGNAL RESOLUTION H-SYNC (KHZ) V -SYNC (HZ) COMPOSITE / S-VIDEO COMPONENT RGB DVI/HDMI NTSC — 15.734 60.0 O — — — P AL/SECAM — 15.625 50.0 O — — — VESA 720 x 400 37.9 85.0 — — O O 640 x 480 31.5 60.0 — — O O 640 x 480 37.9 72.8 — — O O 640 x 480 37.5 75.0 — — O O 640 x 480 43.3 85.0 — — O O ...

  • Vivitek Q7 Plus - page 62

    56 EDTV 480p 31.469 60.0 — O — O 576p 31.25 50.0 — O — O HDTV 720p 37.5 50.0 — O — O 720p 45.0 60.0 — O — O 1080i 33.8 60.0 — O — O 1080i 28.1 50.0 — O — O 1080p 67.5 60.0 — O — O 1080p 56.3 50.0 — O — O O: Frequency supported —: Frequency not supported *: Displayable level 2D to 3D T iming T able The unit automati ...

  • Vivitek Q7 Plus - page 63

    57 3D T iming T able The unit automatically determines PC signals to select the appropriate resolution. Some signals may require manual adjustment. 3D RESOLUTION HDMI 3D FORMA T 800 x 600 @ 120Hz O Frame sequential 1024 x 768 @ 120Hz O Frame sequential 1280 x 720 @ 120Hz O Frame sequential HD 1080p 24 FPS O Frame packing SD 720p 60 FPS O Frame pack ...

  • Vivitek Q7 Plus - page 64

    58 Qumi Dimensions 238 mm 180 mm 40 mm 238 mm 125 T ripod Hole: :#1/4-20 Max L=0.3 inch Ceiling Mount Hole: M4xP0.7 L=8 mm (Max) 70 35 88 100 170 Note: When installing, ensure that you use only UL Listed ceiling mounts. For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 8 mm (0.31 inch). The constr ...

  • Vivitek Q7 Plus - page 65

    59 Regulatory Compliance FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, ...

Manufacturer Vivitek Category Video projector

Documents that we receive from a manufacturer of a Vivitek Q7 Plus can be divided into several groups. They are, among others:
- Vivitek technical drawings
- Q7 Plus manuals
- Vivitek product data sheets
- information booklets
- or energy labels Vivitek Q7 Plus
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vivitek Q7 Plus.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vivitek Q7 Plus, service manual, brief instructions and user manuals Vivitek Q7 Plus. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vivitek Q7 Plus.

Similar manuals

A complete manual for the device Vivitek Q7 Plus, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vivitek Q7 Plus by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vivitek Q7 Plus.

A complete Vivitek manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vivitek Q7 Plus - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vivitek Q7 Plus, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vivitek Q7 Plus, that we can find in the current document
3. Tips how to use the basic functions of the device Vivitek Q7 Plus - which should help us in our first steps of using Vivitek Q7 Plus
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vivitek Q7 Plus
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vivitek Q7 Plus in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vivitek Q7 Plus?

Use the form below

If you did not solve your problem by using a manual Vivitek Q7 Plus, ask a question using the form below. If a user had a similar problem with Vivitek Q7 Plus it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)