English dropdown-ico

Manual DeWalt DW515K

22 pages 1.4 mb
Download

Go to site of 22

Summary
  • DeWalt DW515K - page 1

    DW505 T aladr o Per cutor 13 mm (1/2") 1/2" (13 mm) Dual Speed Range Hammer drill INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. MANUAL DE INSTRUCCIONES INSTRUCTION MANUAL ¿Dudas? Visítenos en Internet: www.dewalt.com Questions? See us on the W ...

  • DeWalt DW515K - page 2

    ...

  • DeWalt DW515K - page 3

    3 Español 3 Defi niciones: Normas de seguridad Las siguientes definiciones describen el nivel de gravedad de cada advertencia. Lea el manual y preste atención a estos símbolos. PELIGRO: indica una situación de peligro inminente que, si no se evita, provocará la muerte o lesiones graves. ADVERTENCIA: Indica una situación de peligro potencial ...

  • DeWalt DW515K - page 4

    4 Español 4 f) Si no se puede evitar el uso de una herramienta eléctrica en una zona húmeda, utilice un dispositivo de corriente residual (residual current device, RCD) de seguridad. El uso de un RCD reduce el riesgo de sufrir una descarga eléctrica. 3) SEGURIDAD PERSONAL a) Permanezca alerta, controle lo que está haciendo y utilice el sentido ...

  • DeWalt DW515K - page 5

    5 Español 5 e) Mantenimiento de las herramientas eléctricas. Revise que no haya piezas en movimiento mal alineadas o trabadas, piezas rotas o cualquier otra situación que pueda afectar el funcionamiento de las herramientas eléctricas. Si encuentra daños, haga reparar la herramienta eléctrica antes de utilizarla. Se producen muchos accidentes ...

  • DeWalt DW515K - page 6

    6 Español 6 T ensión (V oltios) Longitud del cable en metros (m) 120–127 V 0–7 7–15 15–30 30–50 220–240 V 0–15 15–30 30–60 60–100 Corriente nominal (Amperios) Sección nominal mínima del cable en milímetros cuadrados (mm 2 ) 0–6 A 1,0 1,5 1,5 2,5 6–10 A 1,0 1,5 2,5 4,0 10–12 A 1,5 1,5 2,5 4,0 12–16 A 2,5 4,0 No recom ...

  • DeWalt DW515K - page 7

    7 Español 7 ........Construcción Clase I .......... terminal a tierra (con conexión a tierra) ......... símbolo de alerta de .........Construcción Clase II seguridad (con aislamiento doble) …/min ... revoluciones o BPM ....golpes por minuto reciprocidad por sfpm ....pies superficies por minuto ............. minuto GUARDE EST AS INSTRUCCIONES ...

  • DeWalt DW515K - page 8

    8 Español 8 P ALANCA DE REVERSA INTERRUPTOR DE GA TILLO BOTÓN DEL SEGURO FIG. 2 VELOCIDAD V ARIABLE El interruptor de gatillo de velocidad variable permite controlar la velocidad. Cuanto más fuerte se pulse el interruptor de gatillo, mayor será la velocidad del taladro per cutor . NOT A: Utilice velocidades bajas para perforar sin haber marcado ...

  • DeWalt DW515K - page 9

    9 Español 9 Selector del modo de martillo o de taladro (Fig. 4) Para cambiar la herramienta del modo de taladro al de martillo (o viceversa) gire el selector hasta la posición que desee, como se muestra en la Figura 4. Para taladrado simple, alinee el símbolo de la broca con el portabrocas. Para las operaciones de martilleo, alinee el símbolo d ...

  • DeWalt DW515K - page 10

    10 Español 10 6. Haga funcionar el motor al r etirar la broca del interior del orificio. Esto evitará que se atasque. 7. Con los taladros de velocidad variable no hay necesidad de hacer una marca de centrado con un punzón. Utilice una velocidad menor para comenzar el orificio y acelere, pr esionando más el gatillo, cuando el orificio tenga la p ...

  • DeWalt DW515K - page 11

    11 Español ADVERTENCIA: Nunca utilice disolventes u otros productos químicos abrasivos para limpiar las piezas no metálicas de la herramienta. Estos productos químicos pueden debilitar los materiales plásticos utilizados en estas piezas. Utilice un paño humedecido sólo con agua y jabón neutro. Nunca permita que penetre líquido dentro de la ...

  • DeWalt DW515K - page 12

    12 English Defi nitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please r ead the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury . WARNING: Indicates a potentially hazardous situation wh ...

  • DeWalt DW515K - page 13

    13 English c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/ or battery pack, picking up or carr ying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning ...

  • DeWalt DW515K - page 14

    14 English • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • W ear safety goggles or other eye protection. Drilling operations cause chips to fly . Flying particles can cause permanent eye damage. • Bits and ...

  • DeWalt DW515K - page 15

    15 English W ARNING: Always use eye protection. All users and bystanders must wear eye protection that conforms to ANSI Z87.1. • The label on your tool may include the following symbols. The symbols and their definitions are as follows: V .......... volts A .......... amperes Hz ........ hertz W......... watts min ...... minutes ....... alternati ...

  • DeWalt DW515K - page 16

    16 English High/Low Speed Operation (Fig. 3) The two speed gear drive in the dual range hammerdrill permits effective operation over an extended range of applications with greater selection of accessories. For LOW SPEED operation, the shift knob located on the underside of the hammerdrill should be r otated so the low speed setting is toward the fr ...

  • DeWalt DW515K - page 17

    17 English For straight drilling, align selector with drill bit symbol. For hammering, align selector with the hammer symbol, as shown in the figure. NOTE: The selector must be in either drill or hammer/drill mode at all times. There ar e no operable positions between the two. FIG. 4 DRILL SETTING HAMMER SETTING Chuck T o insert the bit, open chuck ...

  • DeWalt DW515K - page 18

    18 English MAINTENANCE WARNING: T o reduce the risk of injury , turn unit off and disconnect tool from power source before installing and removing accessories, before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury . Y our D E WAL T power tool has been designed to operate over a long ...

  • DeWalt DW515K - page 19

    19 English MAXIMUM RECOMMENDED CAP ACITIES DW505 CHUCK CAP ACITY 1/2" (13 mm) R.P .M. 0–1,100 – 0–2,700 BITS, MET AL DRILLING 3/8" (10 mm) low speed WOOD, FLA T BORING 1-1/2" (38 mm) low speed BITS, MASONRY DRILLING 3/4" (19 mm) soft materials HOLE SAWS 2-1/8" (53.9 mm) – Low speed Repairs T o assure product SAFETY ...

  • DeWalt DW515K - page 20

    ...

  • DeWalt DW515K - page 21

    ...

  • DeWalt DW515K - page 22

    D E W AL T Industrial T ool Co., 701 East Joppa Road, Baltimore, MD 21286 (NOV11) Part No. N142137 DW505 Copyright © 2003, 2006, 2011 D E WAL T The following are trademarks for one or mor e D E W AL T power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuratio ...

Manufacturer DeWalt Category Cordless Drill

Documents that we receive from a manufacturer of a DeWalt DW515K can be divided into several groups. They are, among others:
- DeWalt technical drawings
- DW515K manuals
- DeWalt product data sheets
- information booklets
- or energy labels DeWalt DW515K
All of them are important, but the most important information from the point of view of use of the device are in the user manual DeWalt DW515K.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals DeWalt DW515K, service manual, brief instructions and user manuals DeWalt DW515K. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product DeWalt DW515K.

Similar manuals

A complete manual for the device DeWalt DW515K, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use DeWalt DW515K by users. Manuals are usually written by a technical writer, but in a language understandable to all users of DeWalt DW515K.

A complete DeWalt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual DeWalt DW515K - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the DeWalt DW515K, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the DeWalt DW515K, that we can find in the current document
3. Tips how to use the basic functions of the device DeWalt DW515K - which should help us in our first steps of using DeWalt DW515K
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with DeWalt DW515K
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of DeWalt DW515K in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning DeWalt DW515K?

Use the form below

If you did not solve your problem by using a manual DeWalt DW515K, ask a question using the form below. If a user had a similar problem with DeWalt DW515K it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)