-
Hearth and Home Technologies 800 - page 1
MODEL 800 NOV A FREEST ANDING PELLET STOVE INST ALLA TION, OPERA TION, AND MAINTENANCE INSTRUCTIONS CONGRA TULA TIONS— Yo u are now the proud owner of one of the finest stoves in the world for your home—the QUADRA- FIRE! Now before installing your stove and building your first fire, record the serial number on the warranty card. The serial numb ...
-
Hearth and Home Technologies 800 - page 2
NOTES Page 2 ...
-
Hearth and Home Technologies 800 - page 3
T ABLE OF CONTENTS Page Safety Label ................................................................................................................... ........................................... 4 Listing and Specifications ..................................................................................................... ...................... ...
-
Hearth and Home Technologies 800 - page 4
SAFETY LABEL (FOUND ON BACK W ALL OF HOPPER) Page 4 ...
-
Hearth and Home Technologies 800 - page 5
LISTINGS AND SPECIFICA TIONS QUADRA-FIRE 800 NOV A pellet stoves are safety tested and listed with W arnock Hersey International to ASTME 1509 and ULCS627. Also suitable for mobile home installation (see page 11 for details). HEA T INPUT*: 28,000 to 37,500 BTU per hour P AR TICULA TE EMISSIONS PER HOUR: 0.9 grams per hour DIMENSIONS: WIDTH-261/2&qu ...
-
Hearth and Home Technologies 800 - page 6
FLOOR PROTECTION MINIMUM CLEARANCES TO COMBUSTIBLE MA TERIALS The floor protector must be noncombustible material, extending beneath heater and to the front, sides, and rear as indicated below . NOTE: In a corner installation, the floor protection must follow the above clearances. VENTING TERMINA TION REQUIREMENTS 1. Do not terminate vent in any en ...
-
Hearth and Home Technologies 800 - page 7
Page 7 ...
-
Hearth and Home Technologies 800 - page 8
Page 8 ...
-
Hearth and Home Technologies 800 - page 9
Page 9 ...
-
Hearth and Home Technologies 800 - page 10
T OP VENT FLUE ADAPTER INST ALLA TION INSTRUCTIONS 3"-3" ADAPTER #81 1-0450 3"-6" COLLAR #812-2690 1 ) Put a layer of silicone on the 3" (76mm) exhaust outlet. 2 ) Slide the flue adapter onto the rear exhaust outlet. 3 ) Adjust the assembly to a vertical position. 4 ) Slide the outer shield up or down to mate evenly with th ...
-
Hearth and Home Technologies 800 - page 11
MOBILE HOME INST ALLA TION OUTSIDE AIR KIT FOR 800 NOV A: P ART #81 1-0420 (FLOOR) OR P AR T #81 1-0430 (REAR) 1 An outside air inlet must be provided for the combustion air and be unrestricted while the stove is in use. 2. The stove must be secured to the mobile home by bolting it to the floor (using lag bolts). 3. Do not install the stove in a sl ...
-
Hearth and Home Technologies 800 - page 12
OPERA TING INSTRUCTIONS 1. FUEL SIZE AND MA TERIAL Fuel pellets are made from sawdust or wood byproducts. If the source material is hardwood, they will have a higher mineral content, creating a heavier ash. Minerals and other noncombustible materials, such as sand, will turn into glass when heated to the extreme temperatures our firepot reaches. Th ...
-
Hearth and Home Technologies 800 - page 13
Page 13 ...
-
Hearth and Home Technologies 800 - page 14
Page 14 ( N ) COMBUSTION BLOWER ( WHITE ) ...
-
Hearth and Home Technologies 800 - page 15
1. FIREPOT A. It takes very little time to clean the firepot. W e recommend that you clean the firepot at least once a week. However , if the fuel you are burning has a high dirt content, it will be necessary to clean the firepot more often. Dirty fuel will cause clinkers to form in the firepot. A clinker is formed when dirt or a nonburnable substa ...
-
Hearth and Home Technologies 800 - page 16
1. POWER SUPPL Y A. Check the wall receptacle for 120 volt, 60 Hz (standard current). Make sure the outlet is grounded and has the correct polarity . 2. FUSE A. The fuse is located on the left side, next to the restart button and the indicator light. However , to access the fuse, you must remove the left side panel. T o inspect the fuse, push the f ...
-
Hearth and Home Technologies 800 - page 17
9. THERMOCOUPLE A. The thermocouple is located on top of the firepot inside the ceramic protection tube. Remove the ceramic tube and inspect the thermocouple for deterioration or breakage. B. Check the terminal block screws to see if they are tight and making a good electrical connection (located on the top of the lower junction box). NOTE: The yel ...
-
Hearth and Home Technologies 800 - page 18
1. PLUG IN STOVE, NO RESPONSE A. Check the power supply for 120 volts AC. B. Check the fuse in the junction box (7 amp, 120 volt fuse AGC-7). C. Check snap disc #3 (unplug stove before checking). Push reset on snap disc #3. D. Control box (consult your dealer). 2. CALL LIGHT ON, NO FIRE, NO FUEL IN FIREPOT A. Check the hopper for fuel, sawdust or b ...
-
Hearth and Home Technologies 800 - page 19
8. THERMOST A T WILL NOT ST ART UNIT A. Check the power to the stove. 1. Unplug for 10 seconds and then plug in. The exhaust blower should come on. If it does, go to B. B. The thermostat or the thermostat wiring maybe faulty . 1. Disconnect the thermostat wires from the terminal block located on the back of the stove. Make a jumper wire in order to ...
-
Hearth and Home Technologies 800 - page 20
Aladdin Hearth Products, warrants their pellet heating appliances to the original purchaser for the lifetime of the appliance, to be free from defects in material and workmanship. This warranty gives you specific legal rights; you may have other rights which may vary from state to state. This limited Lifetime W arranty covers items such as but not ...
Do you have a question concerning Hearth and Home Technologies 800?
Use the form below
If you did not solve your problem by using a manual Hearth and Home Technologies 800, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies 800 it is likely that he will want to share the way to solve it.