Manual Multi-Tech Systems 410

79 pages 3.03 mb
Download

Go to site of 79

Summary
  • Multi-Tech Systems 410 - page 1

    MultiVOIP ® V oice/Fax over IP Gateways Configuration Guide for MultiVOIP Units deployed with Avaya TM Communication Manager Models: MVP-130/210/410/810-AV ...

  • Multi-Tech Systems 410 - page 2

    Configuration Guide S000299G Analog MultiVOIP Units Models MVP- 130/210/410/ 810-AV for u se with Avaya TM Communication Manager This publication may not be reproduced, in whole or in pa rt, without prior expressed wr itten permission from Multi- Tech Systems, Inc. All rights reserved. Copyright © 2008, by Multi-Tech Systems, Inc. Multi-Tech Syste ...

  • Multi-Tech Systems 410 - page 3

    CONTENTS V OICE /F AX OVER IP G ATEW AYS ................................................................................................. 1 C HAPTER 1 - I NTRODUCTION ....................................................................................................... 4 About This Manual .......................................................... ...

  • Multi-Tech Systems 410 - page 4

    Chapter 1 - Introduction 4 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Chapter 1 - Intr oduction About This Man ual MultiVOIP mode ls (MVP130- AV, MVP130- AV-FXS, MVP21 0-AV, MVP41 0-AV, & MVP810- AV) being us ed in systems containin g Avaya PBX units and controlled b y Avaya TM Communication Mana ger software differ only slightl ...

  • Multi-Tech Systems 410 - page 5

    Chapter 1 - Introduction Multi-Tech Systems, Inc. Avaya Communication Manager Guide 5 Figure 1. MultiVOIP in Avaya Communication Manager System The MVP810-AV shown in the diagram on the previous page functions as a gateway registered to one of the Communication Managers in the IP network. The MVP810-A V provides survivable ca lling between the IP P ...

  • Multi-Tech Systems 410 - page 6

    Chapter 2 – Configuration 6 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Chapter 2 - Configuration Configuring MultiV OIP f or A va ya Comm unication Manager Use To configure the MultiVOI P unit within such a sy stem (sim ilar to that in Figure 1), use the Communica tion Manager Parameters screen within the MultiVOIP program. If “ ...

  • Multi-Tech Systems 410 - page 7

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 7 1e. TCP/UDP port requremen ts. To ensure proper functioning of the Mult iVOIP, the TCP/UDP network connection must not be blocked on th e network connection between the MultiVOIP and CM. The UDP ports used by the MultiVOIP are as follows: Channel RTP Port RTCP Po ...

  • Multi-Tech Systems 410 - page 8

    Chapter 2 – Configuration 8 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 2. Configure Interface Parameters. 2a. Determine which voice ch annels will be stations (FXS), tr unks (FXO/DID), or dis abled. Configure them as such in the Configuration | Interface screen of the MultiVOIP GUI. 2b. If you are configuring a DI D-DPO (Direct In ...

  • Multi-Tech Systems 410 - page 9

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 9 using a non- Avaya analog t elephone. This stat ion must be proper ly administered in the Audix Voice Ma il System fo r the message wa iting featu re to work. 2d. Activate the “Cal ler ID” feature if you h ave FXS Interf ace selected and are u sing an analog ...

  • Multi-Tech Systems 410 - page 10

    Chapter 2 – Configuration 10 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 3. Configure Voice/Fax Para meters. 3a. In the MultiVOIP’ s Configuration | Voice/F ax Parameters screen, configure the voice channels for a voice coder that is supported by Communic ation Manager. The voice coder selected must match the voice cod ers listed ...

  • Multi-Tech Systems 410 - page 11

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 11 handset (and without dialing the nu mber) immediately call the far-en d party. To prevent toll fraud on FXO trunk ports, set the “autoc all enable” feature and enter the phone numbe r for a receptionist or auto-attendent . 3c. The MultiVOIP supports off-hook ...

  • Multi-Tech Systems 410 - page 12

    Chapter 2 – Configuration 12 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 4c. Configure Gateway Name (option al). This is the name that gets displayed when viewing C all Progress statistics for this ch annel. If used, the MultiVOIP’s Gateway Name must match the name used in the Communication Manager “Node-Names IP” f orm. 4d. ...

  • Multi-Tech Systems 410 - page 13

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 13 Note that, in page 2 of the Communication Ma nager “Station” form, the “ Direct IP-IP Audio Connection” field must be set to “y” and the “IP Au dio Hairpinni ng” field must be set to “n.” 4e. Configure Sec urity Code. This must match the secu ...

  • Multi-Tech Systems 410 - page 14

    Chapter 2 – Configuration 14 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 5. Configure trunk ( FXO) channels in the Commu nication Manager P arameters screen. Communication Manager MultiVOIP: FXO Channels 5a. Make sure the “Register with Communica ti on Manager Gatekeeper” option is ch ecked. ...

  • Multi-Tech Systems 410 - page 15

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 15 5b. Configure C all Signaling P ort. Unlike station (FXS) ports, which re quire a uniqu e value for each channel, trunk (FXO) ports requi re that the same Call Sign aling Port value be use d on all trunk (FXO) ports that are registered to the same Co mmunication ...

  • Multi-Tech Systems 410 - page 16

    Chapter 2 – Configuration 16 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 5g. To accommodate the MultiVOIP unit, the fol low ing fields in the Communication Manager “Trunk Group – Page 1” form must be set as shown: Dial A ccess? = y Service Type = tie Group Type = ISDN Carrier Medium = IP/H.323 5h. To accommodate the MultiVOIP ...

  • Multi-Tech Systems 410 - page 17

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 17 6. Configure trunk (DID ) channels in the Communicatio n Manager Parameters scr een. Communication Manager Multi VOIP: DID Channels 6a. Make sure the “Register with Communica ti on Manager Gatekeeper” option is ch ecked. ...

  • Multi-Tech Systems 410 - page 18

    Chapter 2 – Configuration 18 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 6b. Configure C all Signaling P ort. Unlike station (FXS) ports, which re quire a uniqu e value for each channel, trunk DID ports require that the same Call Signaling Port value be used on all DID trunk ports that are registered to the same Communicati on Mana ...

  • Multi-Tech Systems 410 - page 19

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 19 6f. To accommodate the MultiVOIP unit, the fo llowing fields in the Communication Manager “Trunk Group – Page 1” form must be set as shown: Dial A ccess? = n Service Type = tie Group Type = ISDN Carrier Medium = IP/H.323 6g. To accommodate the MultiVOIP un ...

  • Multi-Tech Systems 410 - page 20

    Chapter 2 – Configuration 20 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 7. Configure MultiVOIP gatekeeper (excep t for the MVP130 Models) to provide survivability to IP phones and local FXS/FXO/DID ports. If you are us ing Avaya IP ph ones in addition to the MultiVOIP, you mu st configure the MultiVOIP gatekeeper to provide surv i ...

  • Multi-Tech Systems 410 - page 21

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 21 7c. To add an entry for MultiV OIP FXO ports, config ure Endpoint Typ e, Product ID, N ames, Registration IP, and Call Signalling Port fields as indicated below. Configure the Names field with a unique descriptive identifier for the FXO tr unk. This same name wi ...

  • Multi-Tech Systems 410 - page 22

    Chapter 2 – Configuration 22 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 7e. To add an entry for an IP p hone, configure Endpoin t Type, Product ID, Names, Phones, and Security code fields as indicated below. Configure Ph ones and Security C ode to match the values configured for this I P phone in Communication Manager. Le ave the ...

  • Multi-Tech Systems 410 - page 23

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 23 7f. Configure the “Survivable GK Node Name” fiel d w ith the node name previously given to the MultiVOIP in the “ Node-Names IP” for m. Avaya IP phones r unning firmware version 2.0 or h igher require CM 2.0.1 or h igher to work in survivable mode with t ...

  • Multi-Tech Systems 410 - page 24

    Chapter 2 – Configuration 24 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 8. Create Outbound Phone Book entr ies to allow the mapping of digit patterns (area codes, 911 c alls, etc) to FXO trunks during gate keeper survivable mode. When a survivable ca ll comes in from t he IP networ k to the MultiVOIP gatekeeper, the MultiVOIP will ...

  • Multi-Tech Systems 410 - page 25

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 25 8b. Click the Add button to add an Outbound Phone Book entry. The Add/Edit Outbound Phone Book screen will be displayed. 8c. Enter the digit pattern 9763 in the Destination Patt ern field. Enter the digit 9 in the Remove Prefix field Enter a description in the D ...

  • Multi-Tech Systems 410 - page 26

    Chapter 2 – Configuration 26 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 8d. Go to the MultiVOIP’s Phone Book | Phone Book Modify | Outbound Phone Book | List Entries screen and click the Add button to add another Outbound Phone Book entry for the 612 area code. Enter the digit pattern of 9612 in the Destination P attern field. E ...

  • Multi-Tech Systems 410 - page 27

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 27 8f. Add an Outbound Phone Book entry to hand le th e routing of 911 e mergency calls to the FXO trunk. Since 911 must be dialed out the FXO trun k, leave the Remove Pre fix field blank. ...

  • Multi-Tech Systems 410 - page 28

    Chapter 2 – Configuration 28 Multi-Tech Systems, Inc. Avaya Communication Manager Guide 8g. The completed Outbound Phone book now includes the entrie s added in the earlier steps. Note: For gatekeeper survivability mode, the Inbound Phone book is not used. 8h. Click on Save Setup | Save and Reboot to save the Outbound Phone Book entries. 9. Diali ...

  • Multi-Tech Systems 410 - page 29

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 29 9c. Gatekeeper Survivability di aling example #3: Incoming Central Office call to station 6011. In this case, the Autocall feature has been enabled in th e Voice/Fax screen of the MultiVOIP for the FXO trunk channels. The Autocall Phone Nu mber field has been se ...

  • Multi-Tech Systems 410 - page 30

    Chapter 2 – Configuration 30 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Regional Parameters screen The main distinguish ing feature of the Region al Parameters screen for Avaya Communication Manager MultiVOIPs is the addition of the surv ivability dial tone. 1. Set the Survivability Tone in the Configuration | Regional Parameters ...

  • Multi-Tech Systems 410 - page 31

    Chapter 2 - Configuration Multi-Tech Systems, Inc. Avaya Communication Manager Guide 31 “Regional Parameter” Definitions Continued Field Name Values Description Gain 2 gain in dB +3dB to –31dB and “mute” setting Amplification factor of higher frequency of pair. This applies to the dial, ring, busy, and ‘unobtainable’ (fast busy) tones ...

  • Multi-Tech Systems 410 - page 32

    Chapter 2 – Configuration 32 Multi-Tech Systems, Inc. Avaya Communication Manager Guide The Custom Tone-Pair Settings fields are described in the table be low. Custom Tone-Pair Settings Definition s Field Name Values Description Tone Pair dial tone, busy tone, ring tone, ‘unobtainable’ tone, survivability tone, re-order tone Identifies the ty ...

  • Multi-Tech Systems 410 - page 33

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 33 Chapter 3 – Related Mult iV OIP Setup P arameters For your convenien ce, the Communication Manager Settin gs, MultiVOIP Voice/Fax, Interface, and Gatekeeper parameters are detailed in this section. Communication Manager Settings In the C ...

  • Multi-Tech Systems 410 - page 34

    Chapter 3 – Related MultiVOIP Setup Parameters 34 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Communication Manager Parameter Defini tions Continued Field Name Values Description Q.931 Parameters Use Fast Start Y/N Enables the H.323 Fast Start procedure. If “R egister with Communication Manager Ga tekeeper” is enabled, this fie ...

  • Multi-Tech Systems 410 - page 35

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 35 Communication Manager Parameter Defini tions (cont’d) Field Name Values Description RAS Time to Live Numeric (in seconds) The MultiVOIP sends this value to CM in the Registration Request (RRQ). However, the MultiVOIP will send “Keepali ...

  • Multi-Tech Systems 410 - page 36

    Chapter 3 – Related MultiVOIP Setup Parameters 36 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Voice/Fax Parameters In each field, enter the values that fit your particular network. ...

  • Multi-Tech Systems 410 - page 37

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 37 Note that Voice/FAX parameters are applied on a ch annel-by-channel basis. However, once you have established a set of Voice/FAX parameters for a part icular channel, you ca n apply this entire set of Voice/FAX parameters to another ch ann ...

  • Multi-Tech Systems 410 - page 38

    Chapter 3 – Related MultiVOIP Setup Parameters 38 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Voice/Fax Parameter Definitions Continued Field Name Values Description DTMF Para meters DTMF Gain -- The DTMF Gain (Dual Tone Multi-Frequency) controls the volume level of the DTMF tones sent out for Touch- Tone dialing. DTMF Gain, High T ...

  • Multi-Tech Systems 410 - page 39

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 39 Voice/Fax Parameter Definitions Continued Field Name Values Description Coder Parameters (cont’d) Selected Coder G.711 a/u law 64 kbps; G.726 , @ 16/24/32/40 kbps; G.727 , @ nine bps rates; G.723.1 @ 5.3 kbps, 6.3 kbps; G.729 , 8kbps; Ne ...

  • Multi-Tech Systems 410 - page 40

    Chapter 3 – Related MultiVOIP Setup Parameters 40 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Voice/Fax Parameter Definitions Continued Field Name Values Description AutoCall/Offhook Alert Parameters Auto Call / Offhook Alert AutoCall, Offhook Alert The AutoCall option enables the local MultiVOI P to place a call without the user h ...

  • Multi-Tech Systems 410 - page 41

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 41 Voice/Fax Parameter Definitions (cont’d) Field Name Values Description Dynamic Jitter (cont’d) Minimum Jitter Value 60 to 400 ms The minimum dynamic jitter buffer of 60 milliseconds is the minimum delay that would be acceptable over a ...

  • Multi-Tech Systems 410 - page 42

    Chapter 3 – Related MultiVOIP Setup Parameters 42 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Interface Parameters In each field, enter the values that fit your particular network. ...

  • Multi-Tech Systems 410 - page 43

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 43 The kinds of parameters for which values must be ch osen depend on the type of telephony sup ervisory signaling or interface used (FXO, E&M, etc.). We present here the variou s parame ters grou ped and organized by interface type. Note ...

  • Multi-Tech Systems 410 - page 44

    Chapter 3 – Related MultiVOIP Setup Parameters 44 Multi-Tech Systems, Inc. Avaya Communication Manager Guide FXS Loop Start Parameters. The p arameters app licable to FXS Loop Start are shown in the figure below and described in the table that follows. FXS Loop Start Interface: Parameter Definitions Field Name Values Description FXS (Loop Start) ...

  • Multi-Tech Systems 410 - page 45

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 45 FXS Loop Start Interface: Parameter Definitions (cont’d ) Field Name Values Description Flash Hook Options f ields Generation -- not applicable to FXS interface Detection Range for Min . and Max ., 50 - 1500 milliseconds For a received f ...

  • Multi-Tech Systems 410 - page 46

    Chapter 3 – Related MultiVOIP Setup Parameters 46 Multi-Tech Systems, Inc. Avaya Communication Manager Guide FXO Parameters. The parameters applicable to the FX O tele phony interface type are shown in the figure below and described in the table that follows. FXO Interface: Parameter Definition s Field Name Values Description Interface, FXO Y/N E ...

  • Multi-Tech Systems 410 - page 47

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 47 FXO Interface: Parameter Definitions (cont’d) Field Name Values Description FXO Disconnect On (cont’ d) Disconnect Tone Sequence 1 st tone pair + 2 nd tone pair These are DTMF tone pairs. Values for first tone pair are: *, #, 0, 1-9, a ...

  • Multi-Tech Systems 410 - page 48

    Chapter 3 – Related MultiVOIP Setup Parameters 48 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Figure 1: Voip Caller ID Case #1 – Call, through telco central office with s ta ndard CI D, enters voip system Figure 2: Voip Caller ID Case #2 – Call, through telco central office without stan dard CID, enters H.323 voip system Figure ...

  • Multi-Tech Systems 410 - page 49

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 49 Figure 4: Voip Caller ID Case #4 – Remote FXS call on H.323 voip system Figure 5: Voip Caller ID Case #5 – Call through telc o centr al office without standard CID enter s DID channel in H.323 voip system E&M Parameters. E&M is ...

  • Multi-Tech Systems 410 - page 50

    Chapter 3 – Related MultiVOIP Setup Parameters 50 Multi-Tech Systems, Inc. Avaya Communication Manager Guide DID Interface Parameter Definitions Field Name Values Description Interface DID-DPO Enables the customer-premises side of DID functionality DID Options MultiVOIP’s use of DID applies on ly for incoming DID calls. The Start Mode used by t ...

  • Multi-Tech Systems 410 - page 51

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 51 GK General Settings The fields in the main gatekeeper screen, the GK Gener al Settings screen, must be configured as shown below. GK General Settings Definitions Field Name Values Description Registration Policy No Endpoints Y/N When selec ...

  • Multi-Tech Systems 410 - page 52

    Chapter 3 – Related MultiVOIP Setup Parameters 52 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Click on the Memory Setting button to access the Memory screen. The configurable fields m ust be configured as shown below. GK General Settings Definitions (cont’d) Field Name Values Description GK Memory Values Maximum Calls 10, 20, 30 ...

  • Multi-Tech Systems 410 - page 53

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 53 Gatekeeper – Endpoints When an endpoint registers with the gatekeeper, the endpoint is act ivated. That is, it becomes an acknowledged participant on the network (o r on a part icular zone of a network). Registration tells the gatekeeper ...

  • Multi-Tech Systems 410 - page 54

    Chapter 3 – Related MultiVOIP Setup Parameters 54 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Existing Endpoints Parameter Definitions Field Name Values Description Type Gatekeeper, Gateway, MCU, Terminal, or Undefined. The endpoint type . When an endpoi nt attempts to register with the Gatekeeper, the Gatekeeper compares th e endp ...

  • Multi-Tech Systems 410 - page 55

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 55 Gatekeeper - Calls The fields of the Current Calls screen are described in the table below. The Calls window displays a li st of all the calls currently taki ng place and the basic details of the calls: Current Calls Field Definitions Fiel ...

  • Multi-Tech Systems 410 - page 56

    Chapter 3 – Related MultiVOIP Setup Parameters 56 Multi-Tech Systems, Inc. Avaya Communication Manager Guide A Call Details screen fo r a call in progre ss can be la unched either by clicking on the “Call Det ails” button for a selected cal l in the Current Calls screen, or by d o uble-clicking on a selected call listed i n the Current Calls ...

  • Multi-Tech Systems 410 - page 57

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 57 Call Details Field Definitions (Cont’d) Field Name Values Description Call General Info (cont’d) Total BW The total amount of b andwidth used by the call. Conf. Goal The type of conference request: create , invite or join . State The l ...

  • Multi-Tech Systems 410 - page 58

    Chapter 3 – Related MultiVOIP Setup Parameters 58 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Call Details Field Definitions (Cont’d) Field Name Values Description Destination Info fields Names The H.323 alias n ame used t o make the call. Phone Numbers The e164 alias phone number used to make the call. Other Aliases: Email An e- ...

  • Multi-Tech Systems 410 - page 59

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 59 Gatekeeper – Network Parameters The fields of the Network Parameters screen must be configured as shown be low. Network Parameter De finitions Field Name Values Description Status Information Use Update button to refresh the Status Infor ...

  • Multi-Tech Systems 410 - page 60

    Chapter 3 – Related MultiVOIP Setup Parameters 60 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Network Parameter De finitions (cont’d) Field Name Values Description Pre-Granted ARQ PreGrant ALL Y/N Select to cause the Gatekee per to send a pregrantedARQ perm ission in the RCF message for each e ndpoint that wishes to register. The ...

  • Multi-Tech Systems 410 - page 61

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 61 Network Parameter De finitions (cont’d) Field Name Values Description Call Mode Direct Mode Sets the call mode to direc t. In this mode, terminals send ARQ me ssages to the Gatekeeper, but pass the call signaling and media control signal ...

  • Multi-Tech Systems 410 - page 62

    Chapter 3 – Related MultiVOIP Setup Parameters 62 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Network Parameter De finitions (cont’d) Field Name Values Description Configuration Parameters (Cont’d) Call IRQ Interval The interval, in seconds, between IRQ messages sent by the Gatekeeper to query the status of calls. IRQ messages ...

  • Multi-Tech Systems 410 - page 63

    Chapter 3 – Related MultiVOIP Setup Parameters Multi-Tech Systems, Inc. Avaya Communication Manager Guide 63 Gatekeeper - Services The fields of the Services screen are described in the table below. Services Screen Definitions Field Name Values Description GK Defined Services Prefix A prefix that identifies the service. Description A description ...

  • Multi-Tech Systems 410 - page 64

    Chapter 3 – Related MultiVOIP Setup Parameters 64 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Services Screen Definitions (cont’d) Field Name Values Description V2 GW Prefixes H.323 Version 2 enables the gateway to spec ify prefixes that the user should dial before the WAN number in order to make a call using a certain medium. E. ...

  • Multi-Tech Systems 410 - page 65

    Chapter 4 - Miscellaneou s Multi-Tech Systems, Inc. Avaya Communication Manager Guide 65 Chapter 4 - Miscellaneous Gatewa y Sur vivability Mode A customer may wish to have some ports on the Mu ltiVOIP gateway not be managed by CM, but rather have them directly routed over a priv ate IP WAN to a second MultiVOIP gateway at the side of the WAN networ ...

  • Multi-Tech Systems 410 - page 66

    Chapter 4 – Miscellaneous 66 Multi-Tech Systems, Inc. Avaya Communication Manager Guide The Inbound Phonebook will be configured as illustrated in the table below. Inbound Destination Pa ttern: Filter & Remove this Prefix Add Prefix Channel to dire ct call toward 6001 1 6002 2 6003 3 6004 4 6005 5 6006 6 9303 303 7 9303 303 8 9720 720 7 9720 ...

  • Multi-Tech Systems 410 - page 67

    Chapter 4 - Miscellaneou s Multi-Tech Systems, Inc. Avaya Communication Manager Guide 67 Remote Configuration Remote configuration prov ides procedures for view ing or changing the configu ration of a remote Mult iVOIP. Remote configuration req uires the MultiVOIP software to be lo aded on the local PC. The loc al PC then controls the remote MultiV ...

  • Multi-Tech Systems 410 - page 68

    Chapter 4 – Miscellaneous 68 Multi-Tech Systems, Inc. Avaya Communication Manager Guide In the Dial String box, enter the AT command for dialing (atd t) plus the phone number of the remote MultiVOIP. Click OK when you are sat isfied with your selections. 7. Run the MultiVOIP Configuration program. Click Start|Programs| MultiVOIP 9.06.XX Configura ...

  • Multi-Tech Systems 410 - page 69

    Chapter 4 - Miscellaneou s Multi-Tech Systems, Inc. Avaya Communication Manager Guide 69 Inf ormation The System Information screen d isplays version an d addressing information on your MultiVOIP. The System Information screen is a display informatio n screen with such in formation as Firmw are Version level, MAC Address, and Serial Number which ca ...

  • Multi-Tech Systems 410 - page 70

    Chapter 4 – Miscellaneous 70 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Note: It is possible for the hardware revision printe d on the packaging label and PCB (printed circuit board) to be higher than what is d isplayed in the Hardware ID field in the System Information screen. In these cases, the features supported are the same a ...

  • Multi-Tech Systems 410 - page 71

    Chapter 4 - Miscellaneou s Multi-Tech Systems, Inc. Avaya Communication Manager Guide 71 Link Management The Link Management screen allows you to ping a remote system by entering the IP address of the remote unit in the IP Address to Ping field. The Link Stat us window displays the results of the ping. Each ping test sends a user configurable numbe ...

  • Multi-Tech Systems 410 - page 72

    Chapter 4 – Miscellaneous 72 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Feature Issues 1. Calling Party Number is not displayed o n the Caller ID for FXS por ts after receiving a c all via CM. This is due to CM not sendin g the Calling Party Numb er to the MultiVOIP as part of the Q.931 setup message. 2. “Unknown Name” is disp ...

  • Multi-Tech Systems 410 - page 73

    Index Multi-Tech Systems, Inc. Avaya Communication Manager Guide 73 Index Accepts Calls op tion (Gatekeeper General Setting s screen) ..... 51 accessing Call D etails (g atekeeper) s c reen ............................... 56 accessing Current Calls (g atekeeper) scr een ............................. 55 accessing Endpoints (gat ekeeper) sc reen .... ...

  • Multi-Tech Systems 410 - page 74

    Index 74 Multi-Tech Systems, Inc. Avaya Communication Manager Guide G.727 .................................................................................... 39 G.729 .................................................................................... 39 Net Coder ............................................................................. 39 Cod ...

  • Multi-Tech Systems 410 - page 75

    Index Multi-Tech Systems, Inc. Avaya Communication Manager Guide 75 analog ................................................................................... 39 echo, removing analog ................................................................................... 39 Enable Survivability Mode f ield, Comm Mgr Parameters scre en ................. ...

  • Multi-Tech Systems 410 - page 76

    Index 76 Multi-Tech Systems, Inc. Avaya Communication Manager Guide gatekeeper Call Signalling IP field (Call D etails, Destination Info) ...................................................................................... 58 gatekeeper Call Signalling IP field (Call D etails, Source Info) 57 gatekeeper Cid Sum fiel d (Call Details) ............. ...

  • Multi-Tech Systems 410 - page 77

    Index Multi-Tech Systems, Inc. Avaya Communication Manager Guide 77 analog ................................................................................... 38 Input Gain field analog ................................................................................... 37 Inter Digit Regeneration Ti me (FXO) field .............................. 46 ...

  • Multi-Tech Systems 410 - page 78

    Index 78 Multi-Tech Systems, Inc. Avaya Communication Manager Guide Phone Number/ Exte nsion fi e ld ................................................ 34 Phone Number/Extension (Comm Mgr Params field) & Extension (Station) field FXS ...................................................................................... 12 Phone Numbers gatekeeper ...

  • Multi-Tech Systems 410 - page 79

    Index Multi-Tech Systems, Inc. Avaya Communication Manager Guide 79 Unregister button, Com m Mg r Parameters screen .................... 34 Unregister endpoints command Gatekeep er ........................................................................... 54 Update button (g atekeeper Network P ara meters) ..................... 62 URQ Unregister R ...

Manufacturer Multi-Tech Systems Category IP Phone

Documents that we receive from a manufacturer of a Multi-Tech Systems 410 can be divided into several groups. They are, among others:
- Multi-Tech Systems technical drawings
- 410 manuals
- Multi-Tech Systems product data sheets
- information booklets
- or energy labels Multi-Tech Systems 410
All of them are important, but the most important information from the point of view of use of the device are in the user manual Multi-Tech Systems 410.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Multi-Tech Systems 410, service manual, brief instructions and user manuals Multi-Tech Systems 410. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Multi-Tech Systems 410.

A complete manual for the device Multi-Tech Systems 410, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Multi-Tech Systems 410 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Multi-Tech Systems 410.

A complete Multi-Tech Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Multi-Tech Systems 410 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Multi-Tech Systems 410, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Multi-Tech Systems 410, that we can find in the current document
3. Tips how to use the basic functions of the device Multi-Tech Systems 410 - which should help us in our first steps of using Multi-Tech Systems 410
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Multi-Tech Systems 410
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Multi-Tech Systems 410 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Multi-Tech Systems 410?

Use the form below

If you did not solve your problem by using a manual Multi-Tech Systems 410, ask a question using the form below. If a user had a similar problem with Multi-Tech Systems 410 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)