English dropdown-ico

Manual Global Machinery Company LS8B

16 pages 1.7 mb
Download

Go to site of 16

Summary
  • Global Machinery Company LS8B - page 1

    REDEYE ® LS8B 030710 MW ED7 INSTRUCTION MANU AL 250W 200mm Band Sa w with Laser Line Generator • Melbourne • Perth • Auckland • Hong K ong • Shanghai • T aipei • New Y ork • V erona • London • P aris ...

  • Global Machinery Company LS8B - page 2

    Contents W arranty 2 Introduction 3 Description of s ymbols 3 Specifications 3 Safety rules for laser lights 3 Safety instructions 4 Additional safety rules f or band saws 5 Unpacking 6 Accessories 6 Know y our product 7 Assembly 8 Upper blade guide adjustment 8 Low er blade guide adjustment 9 Housing doors 10 Adjusting the rip fence 10 Adjusting t ...

  • Global Machinery Company LS8B - page 3

    Description of s ymbols The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use . Wear hearing protection. Wear eye protection. Wear breathing protection. Conforms to relevant standards f or electromagnetic compatibility. Specifications Nominal voltage: 230–240V ac ~ 50Hz ...

  • Global Machinery Company LS8B - page 4

    • Never aim the beam at any person or an object other than the work piece . • The laser beam shall not be deliberately aimed at personnel and shall be prevented from being directed towards the eye of a person f or longer than 0.25s. • Always ensure the laser beam is aimed at a sturdy work piece without reflective surfaces . I.e . wood or roug ...

  • Global Machinery Company LS8B - page 5

    8. Use safety accessories. Safety glasses and earmuff s should always be worn. A face or dust mask is also required if the operation creates dust. 9. Do not abuse the pow er cord. Never pull the cord to disconnect the charger from the power point. Keep the cord away from heat, oil and sharp edges. 10. Do not o verr each. Keep your f ooting secure a ...

  • Global Machinery Company LS8B - page 6

    • Support the work properly. • Never reach over the blade to remove waste or o ff cuts. • Do not attempt to free a jammed blade bef ore first switching off the machine . • Do not slow or stop a blade with a piece o f wood. Let the blade come to rest naturally. • If you are interrupted when operating the saw , complete the process and swit ...

  • Global Machinery Company LS8B - page 7

    Know y our product 1. Saw blade 2. Upper housing locking screw 3. Lower housing locking screw 4. Upper housing door 5. Lower housing door 6. Laser assembly 7. Laser on/off switch 8. Blade tension knob 9. On/Off switch 10. Work table trunnion 11. Work table 12. T able insert 13. Rip fence 14. Rip fence locking handle 15. Upper blade guide 16. Blade ...

  • Global Machinery Company LS8B - page 8

    8 Mounting 1. It is best to attach the band saw to a firm, stable surf ace at a convenient working height. A workbench is ideal. 2. Drill four holes in the workbench to match the f our holes in the base of the saw . 3. Attach the band saw to the work bench using 8mm bolts (inserted from the top), lock washers and nuts. Assembly The band saw is ship ...

  • Global Machinery Company LS8B - page 9

    9 3. T o adjust the height of the upper blade guide loosen the blade guide locking knob (17) and then adjust the height using the blade guide setting knob (16). 4. Tighten the blade guide locking knob (17) to secure the upper blade guide in place . 5. The upper blade guide consists of a thrust bearing that supports the band saw blade from the rear ...

  • Global Machinery Company LS8B - page 10

    10 4. The work table needs to be tilted 45 ° or removed before the thrust bearing locking screw and guide pins can be adjusted. Thrust bearing adjustment 5. T o adjust the thrust bearing loosen the thrust bearing locking screw using the Allen key supplied. It is easier to access the thrust bearing screw if the work table trunnion is placed on a 45 ...

  • Global Machinery Company LS8B - page 11

    11 Adjusting the be vel angle W ARNING. Always ensure that the saw is switched off and unplugged from the power supply before making any adjustments. The bevel adjustment allows material to be cut at an angle from 0 ° to 45 ° . 1. Loosen the table locking knob (20). 2. Loosen the table setting lever (21). The lever works on a cam allowing you to ...

  • Global Machinery Company LS8B - page 12

    12 2. While rotating the bandsaw wheel by hand, turn the blade tracking adjustment knob (18) in a clockwise direction if the band saw blade runs towards the front of the saw . 3. Turn the blade tracking adjustment knob (18) in an anti-clockwise direction if the band saw blade runs towards the rear of the saw . 4. Tighten the blade tracking locking ...

  • Global Machinery Company LS8B - page 13

    13 1. Remove the rip fence (13) from the table . 2. Remove the U shape from under the work table by removing the two screws and two thumb nuts. 3. Open both housing doors. 4. Swing the lower blade guide out of the way. 5. Loosen the blade tension knob to slacken the blade . 6. Remove the blade by guiding it through the slot in the work table , the ...

  • Global Machinery Company LS8B - page 14

    14 Using the REDEYE laser line generat or W ARNINGS. Do not stare directly at the laser beam. Never aim the beam at any person or an object other than the work piece . Do not deliberately aim the beam at personnel and ensure that it is not directed towards the eye of a person. Always ensure the laser beam is aimed at a sturdy work piece without ref ...

  • Global Machinery Company LS8B - page 15

    Maintenance Note . Always wear eye protection when cleaning the tool. W ARNING. Always ensure that the saw is switched o ff and unplugged from the power supply before carrying out any maintenance or cleaning. 1. Keep the tool ’ s air vents unclogged and clean at all times. 2. Remove dust and dirt regularly. Cleaning is best done with a brush or a ...

  • Global Machinery Company LS8B - page 16

    Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Product Code A GMC Service Engineer wil ...

Manufacturer Global Machinery Company Category Saw

Documents that we receive from a manufacturer of a Global Machinery Company LS8B can be divided into several groups. They are, among others:
- Global Machinery Company technical drawings
- LS8B manuals
- Global Machinery Company product data sheets
- information booklets
- or energy labels Global Machinery Company LS8B
All of them are important, but the most important information from the point of view of use of the device are in the user manual Global Machinery Company LS8B.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Global Machinery Company LS8B, service manual, brief instructions and user manuals Global Machinery Company LS8B. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Global Machinery Company LS8B.

Similar manuals

A complete manual for the device Global Machinery Company LS8B, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Global Machinery Company LS8B by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Global Machinery Company LS8B.

A complete Global Machinery Company manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Global Machinery Company LS8B - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Global Machinery Company LS8B, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Global Machinery Company LS8B, that we can find in the current document
3. Tips how to use the basic functions of the device Global Machinery Company LS8B - which should help us in our first steps of using Global Machinery Company LS8B
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Global Machinery Company LS8B
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Global Machinery Company LS8B in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Global Machinery Company LS8B?

Use the form below

If you did not solve your problem by using a manual Global Machinery Company LS8B, ask a question using the form below. If a user had a similar problem with Global Machinery Company LS8B it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)