English dropdown-ico

Manual Kicker CX300.4

32 pages 1.11 mb
Download

Go to site of 32

Summary
  • Kicker CX300.4 - page 1

    CX MUL TI-CHANNEL AMPS CX300.4 Owner’s Manual | English Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE CX.4 Benutzerhandbuch | Deutsch VERSTÄRKER DER CX.4-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE CX.4 CX Amplifiers 2012 CX 4-Channel Amps Rev F.indd 1 2012 CX 4-Channel Amps Rev F.indd 1 6/22/2012 2:45:18 PM 6 ...

  • Kicker CX300.4 - page 2

    2 CX.4-SERIES AMPLIFIERS OWNER’S MANUAL INST ALLA TION Mounting: Choose a structurally sound location to mount your KICKER amplifi er . Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifi er . If possible, mount the amplifi er in th ...

  • Kicker CX300.4 - page 3

    3 Wiring: Disconnect the vehicle’ s battery to avoid an electrical short. Then, connect the ground wire to the amplifi er . Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid, metal area of the vehicle’ s chassis. Adding an additional ground wire of this same gauge (or larger) between the batt ...

  • Kicker CX300.4 - page 4

    4 GND REM +12V FOUR CHANNEL OPERA TION minimum impedance of 2 ohms per channel POWER WIRING GND REM +12V AMP1 AMP2 L R 12V battery external fuse remote turn-on (see page 6) bare-metal chassis ground bare-metal chassis ground  18” (45cm)  24” (60cm) Model External Fuse (sold separately) Power/Ground W ire KICKER W iring Kit CX300.4 1 x 60 ...

  • Kicker CX300.4 - page 5

    5 GND REM +12V GND REM +12V BRIDGED OPERA TION (MONO) minimum impedance of 4 ohms STEREO-AND-MONO-SIMUL T ANEOUSL Y (SAMS) OPERA TION minimum impedance of 4 ohms bridged (mono) and 2 ohms per channel stereo L R 2012 CX 4-Channel Amps Rev F.indd 5 2012 CX 4-Channel Amps Rev F.indd 5 6/22/2012 2:45:33 PM 6/22/2012 2:45:33 PM ...

  • Kicker CX300.4 - page 6

    6 audio inputs OPERA TION Automatic T ur n-On Selection: The CX series offers two automatic turn-on modes; +12V and DC Offset. • Remote T urn-On: Run 18 gauge wire from the Remote T urn-On Lead on your source unit to the terminal labeled REM between the amplifi er ’ s positive and negative power terminals. This is the preferred automatic turn- ...

  • Kicker CX300.4 - page 7

    7 TROUBLESHOOTING If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There are Power (PWR) & Protection (PRT) LEDs on the side panel of your Kicker CX series amplifi er . Depending on the sta ...

  • Kicker CX300.4 - page 8

    8 KICKER will now provide a thr ee- year warranty with all CX-Series Amplifi er purchases paired with a qualifying KICKER Installation Kit* . This extends the standard warranty by an additional year . Amplifi er and Kit must be purchased from an Authorized KICKER Dealer . KICKER CX amplifi er success is currently at an unheard-of rate, making th ...

  • Kicker CX300.4 - page 9

    9 AMPLIFICADOR DE LA SERIE CX.4 MANUAL DEL PROPIET ARIO INST ALLA TION Montaje: Escoja un lugar estructuralmente sólido para montar el amplifi cador KICKER. Asegúrese de que no haya nada por detrás de dónde van a entrar los tornillos. Escoja un lugar en que queden por lo menos 4 plg. (10 cm) de espacio abierto de ventilación alrededor del amp ...

  • Kicker CX300.4 - page 10

    10 Cableado: Desconecte la batería del vehículo para evitar cortocircuitos. Luego, conecte un cable de conexión a tierra al amplifi cador . El cable de conexión a tierra debe ser corto, de 24 plg. (60 cm) o menos, y debe ir conectado a un punto sólido del chasis del vehículo en que no haya ni pintura ni corrosión. T ambién se recomienda in ...

  • Kicker CX300.4 - page 11

    11 GND REM +12V AMP1 AMP2 L R 12V Modelo Fusible Externo (no incluido) Cable de Alimentación y Conexión a T ierra Kit de cableado KICKER CX300.4 1 x 60 Ampere Calibre 8 PK8, ZCK84  18” (45cm)  24” (60cm) encendido a distancia (página 13) conexión a tierra conexión a tierra fusible externo batería GND REM +12V FUNCIONAMIENTO POR QUA ...

  • Kicker CX300.4 - page 12

    12 GND REM +12V GND REM +12V FUNCIONAMIENTO EN PUENTE (MONOFÓNICO) impedancia mínima de 4 ohmios en puente FUNCIONAMIENTO SIMUL TÁNEO EN ESTEREOFÓNICO Y MONOFÓNICO impedancia mínima de 4 ohmios en monofónico y 2 ohmios por canal en estereofónico simultáneamente L R 2012 CX 4-Channel Amps Rev F.indd 12 2012 CX 4-Channel Amps Rev F.indd 12 6 ...

  • Kicker CX300.4 - page 13

    13 señal de entrada FUNCIONAMIENTO Selección de Encendido Automático: La serie CX ofrece dos modalidades de encendido automático que: +12V , y compensación de CC. • Encendido a Distancia: Instale cable calibre 18 desde el conductor de encendido a distancia de la unidad fuente hasta la terminal etiquetada REM entre las terminales de alimentac ...

  • Kicker CX300.4 - page 14

    14 RESOLUCIÓN DE PROBLEMAS Si su amplifi cador parece no estar funcionando, revise lo obvio primero: fusibles quemados, conexiones malas o incorrectas, posición incorrecta de los selectores de crossover y amplifi cación, etc. Su amplifi cador modelo CX de KICKER cuenta con los LED de protección (PRT) y de encendido (PWR) en el panel de alime ...

  • Kicker CX300.4 - page 15

    15 CX300.4 40 x 4 @ 4 ohmios, 14.4VCC, 1% THD, CEA-2006B (Watts) Relación de Señal a Ruido -75dB CEA-2006B (ref: 1W , ponderado en A) 2012 CX 4-Channel Amps Rev F.indd 15 2012 CX 4-Channel Amps Rev F.indd 15 6/22/2012 2:45:37 PM 6/22/2012 2:45:37 PM ...

  • Kicker CX300.4 - page 16

    16 VERSTÄRKER DER CX.4 SERIE BENUTZERHANDBUCH INST ALLA TION Befestigung: Wählen Sie für die Installation des KICKER-V erstärkers eine strukturell stabile Stelle. Vergewissern Sie sich, dass sich hinter der Einschraubposition der Schrauben nichts befi ndet. Wählen Sie eine Stelle, die mindestens 10 cm Lüftungsfreiraum für den V erstärker b ...

  • Kicker CX300.4 - page 17

    17 Anschluss: T rennen Sie den Anschluss der Fahrzeugbatterie, um einen Kurzschluss zu vermeiden. Schließen Sie dann das Massekabel an den V erstärker an. Verwenden Sie ein kurzes Erdungskabel (maximal 60 cm) und schließen Sie es an eine lack- oder korrosionsfreie Metallstelle an der Fahrzeugkarosserie an. Es wird auch empfohlen, ein weiteres Ma ...

  • Kicker CX300.4 - page 18

    18 GND REM +12V AMP1 AMP2 L R 12V Modell Externe Sicherung (nicht inbegriffen) Massekabel KICKER V erkabelungssatz CX300.4 1 x 60 Ampere 8 GA PK8, ZCK84  18” (45cm)  24” (60cm) Installieren Sie in maximal 45 cm Entfernung von der Batterie eine Sicherung in Reihe mit dem Stromkabel zum V erstärker . Wenn Sie je den V erstärker nach der I ...

  • Kicker CX300.4 - page 19

    19 GND REM +12V GND REM +12V BRÜCKENBETRIEB (MONO) Minimalimpedanz von 4 Ohm GLEICHZEITIGER STEREO- UND MONO-BETRIEB (SAMS) Mindestimpedanz von 4 Ohm (Mono) bzw . 2 Ohm pro Kanal (Stereo) bei gleichzeitigem Betrieb L R 2012 CX 4-Channel Amps Rev F.indd 19 2012 CX 4-Channel Amps Rev F.indd 19 6/22/2012 2:45:38 PM 6/22/2012 2:45:38 PM ...

  • Kicker CX300.4 - page 20

    20 OPERA TION Automatische Einschaltung: Die CX-Serie bietet zwei verschiedene automatische Einschaltmethoden, die an der Endplatte gewählt werden können: +12V und DC Offset. • Remote T urn-On (Ferneinschaltung): Verlegen Sie 18 GA-Kabel von der Ferneinschaltung an Ihrem Autoradio zum REM-T erminal zwischen den positiven und negativen Stromansc ...

  • Kicker CX300.4 - page 21

    21 PROBLEMBEHEBUNG Wenn der V erstärker nicht zu funktionieren scheint, sollten Sie zuerst offensichtliche Faktoren prüfen, wie durchgebrannte Sicherungen, schlechte oder fehlerhafte V erkabelung, inkorrekte Einstellung des Crossover- Schalters und der V erstärkungsregler etc. Am seitlichen Einschaltfeld des Kicker CX-Verstärkers befi nden sic ...

  • Kicker CX300.4 - page 22

    22 CX300.4 40 x 4 @ 4 ohms, 14.4GS, 1% Klirrfaktor , CEA-2006B (Watts) Rauschabstand -75dB CEA-2006B (ref: 1W , A-gewichtet) 2012 CX 4-Channel Amps Rev F.indd 22 2012 CX 4-Channel Amps Rev F.indd 22 6/22/2012 2:45:39 PM 6/22/2012 2:45:39 PM ...

  • Kicker CX300.4 - page 23

    23 AMPLIFICA TEUR SÉRIE CX.4 MANUEL D’UTILISA TION INST ALLA TION Montage: Choisissez un emplacement de structure saine pour monter votre amplifi cateur KICKER. Assurez- vous que l’arrière de l’emplacement où vous allez enfoncer les vis ne comporte aucun élément. Choisissez un endroit assurant au moins 10 cm (4 po) de dégagement de ven ...

  • Kicker CX300.4 - page 24

    24 Câblage: Débranchez la batterie du véhicule pour éviter un court-circuit. Ensuite, raccordez le fi l de masse à l’amplifi cateur . Le fi l de masse doit être le plus court possible, de 60 cm (24 po) maximum. Raccordez-le à une partie métallique solide du châssis du véhicule, ne comportant ni peinture ni rouille. Il est recommandé ...

  • Kicker CX300.4 - page 25

    25 GND REM +12V AMP1 AMP2 L R 12V Modèle Fusible Externe (non inclus) Fil de Masse / Alimentation KICKER Kit de câblage CX300.4 1 x 60 Ampere 8 Gauge PK8, ZCK84  18” (45cm)  24” (60cm) Installez un fusible dans un rayon de 45 cm (18 po) de la batterie directement sur le câble d’alimentation raccordé à votre amplifi cateur . Instal ...

  • Kicker CX300.4 - page 26

    26 GND REM +12V GND REM +12V FONCTIONNEMENT PONTÉ (MONO) impédance minimum de 4 ohms FONCTIONNEMENT SIMUL T ANÉ STÉRÉO ET MONO (SAMS) impédance minimum simultanément de 4 ohms en mono et 2 ohms par canal en stéréo L R 2012 CX 4-Channel Amps Rev F.indd 26 2012 CX 4-Channel Amps Rev F.indd 26 6/22/2012 2:45:40 PM 6/22/2012 2:45:40 PM ...

  • Kicker CX300.4 - page 27

    27 UTILISA TION Sélection de Mise sous T ension Automatique : La série CX est dotée de deux modes différents de mise sous tension automatique: +12V et DC Offset (décalage c.c.). • Mise sous T ension à Distance : Faites passer un fi l de calibre 18 à partir du fi l de mise sous tension à distance sur votre appareil source jusqu’à la b ...

  • Kicker CX300.4 - page 28

    28 EN CAS DE DIFFICUL TÉ Si votre amplifi cateur ne marche pas, vérifi ez d’abord les possibilités évidentes comme les fusibles sautés, les branchements incorrects ou desserrés, le mauvais réglage des commandes de gain et du commutateur du fi ltre, etc. Se présentent également des DEL d’alimentation (PWR) et de protection (PRT) sur ...

  • Kicker CX300.4 - page 29

    29 CX300.4 40 x 4 @ 4 ohms, 14.4V C.C., 1% de Distorsion Harmonique T otale, CEA-2006B (W) Rapport Signal sur Bruit -75dB CEA-2006B (ref: 1W , pondéré A) 2012 CX 4-Channel Amps Rev F.indd 29 2012 CX 4-Channel Amps Rev F.indd 29 6/22/2012 2:45:41 PM 6/22/2012 2:45:41 PM ...

  • Kicker CX300.4 - page 30

    30 P .O. Box 459 • Stillwater , Oklahoma 74076 • USA • (405) 624–8510 ELECTRONICS LIMITED W ARRANTY When purchased from an Authorized KICKER Dealer , KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is ...

  • Kicker CX300.4 - page 31

    31 INTERNA TIONAL W ARRANTY Contact your International KICKER dealer or distributor concerning specifi c procedures for your country’s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! T urning up a system to a level that has audible distortion is more damaging to your ear ...

  • Kicker CX300.4 - page 32

    ©2012 Stillwater Designs 2012 CX 4-Channel Amps Rev F.indd 32 2012 CX 4-Channel Amps Rev F.indd 32 6/22/2012 2:45:42 PM 6/22/2012 2:45:42 PM ...

Manufacturer Kicker Category Car Amplifier

Documents that we receive from a manufacturer of a Kicker CX300.4 can be divided into several groups. They are, among others:
- Kicker technical drawings
- CX300.4 manuals
- Kicker product data sheets
- information booklets
- or energy labels Kicker CX300.4
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kicker CX300.4.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kicker CX300.4, service manual, brief instructions and user manuals Kicker CX300.4. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kicker CX300.4.

Similar manuals

A complete manual for the device Kicker CX300.4, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kicker CX300.4 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kicker CX300.4.

A complete Kicker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kicker CX300.4 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kicker CX300.4, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kicker CX300.4, that we can find in the current document
3. Tips how to use the basic functions of the device Kicker CX300.4 - which should help us in our first steps of using Kicker CX300.4
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kicker CX300.4
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kicker CX300.4 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kicker CX300.4?

Use the form below

If you did not solve your problem by using a manual Kicker CX300.4, ask a question using the form below. If a user had a similar problem with Kicker CX300.4 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)