English dropdown-ico

Manual Kathrein UFS 740sw

88 pages 6.74 mb
Download

Go to site of 88

Summary
  • Kathrein UFS 740sw - page 1

    Operating manual - Englisch - DVB Satellite Receiver UFS 740sw ...

  • Kathrein UFS 740sw - page 2

    2 Electronic equipment is not domestic waste - in accordance with directive 2002/96/EC OF THE EUROPEAN P ARLIAMENT AND THE COUNCIL dated 27 th January 2003 on used electrical and electronic appliances, it must be disposed of properly . At the end of its service life, take this unit for disposal to an appropriate of fi cial collection point. Used b ...

  • Kathrein UFS 740sw - page 3

    3 The channels available on the satellites and transponders are subject to continual change. If changes do occur , the new channels have to be set in the receiver because the factory preset programming corresponds to the status on the date of manufacture. The information for these settings can be found on the Internet or in relevant magazines. Y ou ...

  • Kathrein UFS 740sw - page 4

    4 CONTENTS PREF ACE .............................................................................................................................. ... 2 IMPORT ANT INFORMA TION ...................................................................................................... 3 CONTENTS ........................................................... ...

  • Kathrein UFS 740sw - page 5

    5 CONTENTS EDIT CHANNEL LIST ............................................................................................................... 53 SELECTION OF THE LIST/CHANNELS TO BE EDITED ............................................................ 53 EDITING LISTS/CHANNELS ........................................................................... ...

  • Kathrein UFS 740sw - page 6

    6 SAFETY INSTRUCTIONS - IMPORT ANT NOTES ...

  • Kathrein UFS 740sw - page 7

    7 RECEIVER FEA TURES/SCOPE OF SUPPL Y The receiver UFS 740sw is suitable for the reception of digital satellite TV and radio channels. The integral Common Interface has slots for two CA modules for decrypting Pay-TV programmes. In addition to providing high-quality pictures and sound, UFS 740 units also feature an attractive design and 16-character ...

  • Kathrein UFS 740sw - page 8

    8 CONTROLS, DISPLA YS AND CONNECTIONS This section provides a brief description of all the controls, displays and connections. Front panel controls and displays 1. On/Off switch (with mains disconnect) 2. Display (cover folded down) 3. Common Interface for two CA modules for Pay-TV cards * ) 4. Ejection button for CA modules In addition there are t ...

  • Kathrein UFS 740sw - page 9

    9 CONNECTION AND SET -UP The following section is intended speci fi cally for specialist dealers. Y ou only need to pay attention to this section if you are carrying out the installation yourself. The “Connection Examples” section provides a sample con fi guration. Do not connect the unit to the power supply until all installation work has be ...

  • Kathrein UFS 740sw - page 10

    10 CONNECTION AND SET -UP Connect the satellite receiver (Cinch socket) and the TV set (Scart socket) using the Cinch to Scart cable supplied, or connect both units (Scart sockets) using a Scart cable (see “Connection Example”). If your TV has a stereo feature, you can receive the sound in stereo via the Scart connection. Use a further Scart ca ...

  • Kathrein UFS 740sw - page 11

    11 CONNECTION AND SET -UP Remove the wood screws supplied from their transport attachment on the underside of the respective mounting piece (2 pieces). V ertically insert each mounting piece into the fi fth slot from the edge, as shown in Fig. 1. Then push each mounting piece downwards and outwards (see Fig. 2) until they lie fl at on the receive ...

  • Kathrein UFS 740sw - page 12

    12 REMOTE CONTROL  Sound on/off  ...  Switch on/input digits for channels, timer etc.  Call up the main menu, exit the menu and return to the TV picture (red) Call up favourites selection ! (green) “Current” view in the EPG % V olume  Exit menu step by step  Changing channel in the programme guide (EPG)  T ransparent videot ...

  • Kathrein UFS 740sw - page 13

    13 The RC 660 remote control supports up to four devices (which are supplied with the RC 660 as standard) as well as the receivers of the UFD 5xx (not UFD 552, 554, 558) and UFD 4xx families. First switch all receivers off (at the power switch). T o con fi gure a receiver to an infrared code: Switch on the relevant receiver . On the remote control ...

  • Kathrein UFS 740sw - page 14

    14 FIRST INST ALLA TION Before using your unit for the fi rst time, read the “Safety Instructions” and “Connection and Set-Up” sections. The “Connection Examples” section provides a sample con fi guration. Do not connect the unit to the power supply until all installation work has been properly carried out. The guidance given in the ? ...

  • Kathrein UFS 740sw - page 15

    15 FIRST INST ALLA TION Use the  buttons to select whether to replace the default channel list with one pre-sorted for Germany , Austria, Switzerland or Italy . If you want to use the default channel list, choose “No” under “Restore Channellist”. Press the ! (green) button to move to the next menu. The following display appears: Use t ...

  • Kathrein UFS 740sw - page 16

    16 FIRST INST ALLA TION Screen display Here you select the type of screen display , depending on the setting of your TV format: - TV format “4:3”: Pan & Scan or Letterbox - TV format “16:9”: Always 16:9 or automatic TV Scart signal output Select the type of video signal at the TV Scart socket here. Select the signal that your TV set can ...

  • Kathrein UFS 740sw - page 17

    17 Satellite and position Use the  buttons to select the desired satellite whose signal is to be received by the tuner . When you have selected your desired satellite, use the  buttons to switch to the selection of the “LNB T ype”. System Select the setting here to match your reception system using the  buttons. If your recept ...

  • Kathrein UFS 740sw - page 18

    18 LNB settings Here use the  buttons to select the LNB type used in your system. The choice is between “Universal” and “User-de fi ned”. Universal: No further input required, since all necessary frequency ranges are covered by a universal LNB. User-de fi ned: If you choose not to use a universal LNB, you must here set the frequency ...

  • Kathrein UFS 740sw - page 19

    19 Satellites and position Use the  buttons to set the desired satellite (selection from 17 pre-programmed options). LNB settings Here use the  buttons to select the LNB type used in your system. The choice is between “Universal” and “User-de fi ned”. Universal: No further input required, since all necessary frequency ranges ar ...

  • Kathrein UFS 740sw - page 20

    20 FIRST INST ALLA TION: One cable Use the  buttons here to select “One cable” as the “System”. Press the  button to move to the next menu item. The following display appears: Number of satellites Use the  buttons to select how many satellites (max. 2) you would like to receive with your reception system. Press the  button ...

  • Kathrein UFS 740sw - page 21

    21 Universal: No further input is required, since all necessary frequency ranges are covered by a universal LNB. Wideband: No further input is necessary , since all frequency ranges are set by the Wideband LNB. User-de fi ned: If you are not using a Universal or a Wideband system, you must set the frequencies here. Y ou can fi nd the necessary in ...

  • Kathrein UFS 740sw - page 22

    22 FIRST INST ALLA TION: One cable (automatic) The receiver searches for the transmission channels on your single-cable system and shows in the next display the available transmission channels (transmission channels already in use by other receivers are also displayed). Use the  buttons to select the transmission channel you want and con fi ...

  • Kathrein UFS 740sw - page 23

    23 Connected equipment Use the  buttons to select the type of system to which they are connected or the single-cable system components fi tted (refer to the manuals, instructions and notes for the system and the system components). Available options: - User-de fi ned - KA THREIN UAS 481 (single-cable feed system, max. four receivers) - KA T ...

  • Kathrein UFS 740sw - page 24

    24 FIRST INST ALLA TION: One cable (manual) If no connection to the single-cable system could be established, the following display appears: Check your settings (frequency and transmission channel) and if necessary call for expert help. Con fi rm this display with the  button. Then press the  button. Y ou will be asked whether you wish to sa ...

  • Kathrein UFS 740sw - page 25

    25 Selection “UAS 481” or “EXR 551” T ransmission channel Use the  buttons to select a free available transmission channel. A maximum of four transmission channels are available (1400, 1516, 1632 and 1748 MHz). T est connection When you have set a free transmission channel, press the  buttons to switch to the “T est connection ...

  • Kathrein UFS 740sw - page 26

    26 Selection “EXR 552” T ransmission channel Use the  buttons to select a free available transmission channel. A maximum of two transmission channels are available (1400 and 1516 MHz). T est connection When you have set a free transmission channel, press the  buttons to switch to the “T est connection” selection fi eld and pres ...

  • Kathrein UFS 740sw - page 27

    27 FIRST INST ALLA TION: One cable (manual) Selection “EXU 908” T ransmission channel Use the  buttons to select a free available transmission channel. A maximum of eight transmission channels are available (1284, 1400, 1516, 1632, 1748, 1864, 1980 and 2096 MHz). Secure channel with PIN The EXU 908 single-cable matrix allows the transmiss ...

  • Kathrein UFS 740sw - page 28

    28 FIRST INST ALLA TION: One cable (manual) Selection “EXR 4 Subscribers” T ransmission channel Use the  buttons to select a free available transmission channel. A maximum of four transmission channels are available (1284, 1400, 1516 and 1632 MHz). T est connection When you have set a free transmission channel, press the  buttons to ...

  • Kathrein UFS 740sw - page 29

    29 FIRST INST ALLA TION: One cable (manual) Selection “EXR 8 Subscribers” T ransmission channel Use the  buttons to select a free available transmission channel. A maximum of eight transmission channels are available (1284, 1400, 1516, 1632, 1748, 1864, 1980, 2096). T est connection When you have set a free transmission channel, press the ...

  • Kathrein UFS 740sw - page 30

    30 Perform channel scan Use the  buttons to select (yes or no) whether you wish to start a channel scan. It is not essential to start a channel scan; instead you can use the factory pre-programmed channels. However the channels do change from time to time (e.g. their frequencies change), which the receiver does not automatically detect, and c ...

  • Kathrein UFS 740sw - page 31

    31 Set Local Time Use the  buttons to set the time zone variation from UTC (formerly GMT) (e.g. for Germany +1 hour). Use the  buttons to switch to the “Automatic clock change” fi eld. Use the  buttons to select whether the receiver should automatically change over to and from summer and winter time. If “On” is selected, ...

  • Kathrein UFS 740sw - page 32

    32 OPERA TING INSTRUCTIONS The structure of the menu concept is based on logical operating sequences. The programme showing on the current selected channel always appears in the top right-hand corner of the screen. Y ou will fi nd detailed descriptions of the selected menu items in the relevant sections of the operating manual! Note: The selected ...

  • Kathrein UFS 740sw - page 33

    33 MENU TREE OPERA TING INSTRUCTIONS Mainmenu Call up the menu by pressing the  button ...

  • Kathrein UFS 740sw - page 34

    34 OPERA TING INSTRUCTIONS The language for the on-screen display is set as follows:  →  → Language selection →  →  → German →  Available options: German, English, Italian, French, Dutch, Spanish, Czech and T urkish. After you have performed the settings, press the  or  button to exit the main menu. Y ou will ...

  • Kathrein UFS 740sw - page 35

    35 ON-SCREEN DISPLA YS (OSD) Channel information is shown for a few seconds each time the channel is changed (this can be changed under “Settings”, “Adjust Displays”) or displayed continuously by pressing the  button. The information for the current radio channel has the same layout. Channel names Channel number from the overall list Num ...

  • Kathrein UFS 740sw - page 36

    36 Calling this up displays the channel selection/sorting list from which you selected the last channel. At the top right you will see the selected channel list (TV or radio channels) displayed. Press the # (blue) button to switch between the TV and radio channel lists. T o the right of it you see the current channel list sort order as selected by ...

  • Kathrein UFS 740sw - page 37

    37 The channel list can show channels sorted by various selection and sorting criteria. Selection and sorting options: - Press the (red) button to call up the favourites list selection. The  buttons allow you to scroll through the existing favourites lists - Press the ! (green) button to return to the overall list (all satellites). Use the ? ...

  • Kathrein UFS 740sw - page 38

    38 EPG - ELECTRONIC PROGRAMME GUIDE CALL UP EPG The EPG is called up by pressing the  button. Each time the EPG is called up, you will automatically be shown the “Current” view , irrespective of which view you were shown the last time you exited the EPG. The following display appears (example): Channel number from the overall list, channel n ...

  • Kathrein UFS 740sw - page 39

    39 EPG - ELECTRONIC PROGRAMME GUIDE Selection options: - (red) button Calls up the recording schedule (display of all pre-programmed recordings) -  button Jump the “Current” view forwards by 15 minutes - " (yellow) button Call up a preview of the currently highlighted channel - # (blue) button Call up the category selection (sorting the ...

  • Kathrein UFS 740sw - page 40

    40 “COMING UP” VIEW (PROGRAMME LISTINGS) The “Coming up” view (programme listings) can be called up at any time in EPG by pressing the " (yellow) button. EPG - ELECTRONIC PROGRAMME GUIDE In the “Coming up” view you will see all the programmes that will be shown in the previous “Current” list of selected channels. Provided that ...

  • Kathrein UFS 740sw - page 41

    41 EPG - ELECTRONIC PROGRAMME GUIDE CA TEGORIES VIEW The “Categories” view can be called up at any time in EPG by pressing the # (blue) button. In the “Categories” view you can see all programmes sorted by category and starting time. The following categories are available for selection: Movies, Series, Sport, Children’s programmes, Chat s ...

  • Kathrein UFS 740sw - page 42

    42 SCAN FUNCTION The scan function can be called up at any time in EPG by pressing the  button. The scan function allows you to search for programmes based on their additional information or their name. Use the keypad to input the desired search expression (see also “Operating Instructions” “Alphanumeric Input”). When you have input the ...

  • Kathrein UFS 740sw - page 43

    43 EPG - ELECTRONIC PROGRAMME GUIDE ADDITIONAL INFORMA TION (i-BUTTON) The additional information can always be called up by pressing the  button whenever the “i symbol” appears in front of the program name (see screenshot on the right). First however the channel must be selected. The following display appears (example): The additional infor ...

  • Kathrein UFS 740sw - page 44

    44 The  (red dot) button allows you to set up a programme at any time for recording on an external recorder . The programme to be recorded can be selected in any of the EPG views, provided the  (red dot) button appears at the bottom of the screen display . Programme present in the EPG: Select the desired programme and press the  (red dot) ...

  • Kathrein UFS 740sw - page 45

    45 Use the  buttons to select the desired recording mode. The recording mode options available are: - Once: The recording will be performed once - Daily: The recording will be performed daily at a time speci fi ed by you - Weekly: The recording will be performed once a week on the same day and at the same time - User-de fi ned: The recordin ...

  • Kathrein UFS 740sw - page 46

    46 EPG - ELECTRONIC PROGRAMME GUIDE RECORD DAIL Y Use the  buttons to select the recording mode “daily” (see screenshot below). Use the  buttons to switch to the selection fi eld “Start” and use the  buttons to select the desired recording starting time. Use the  buttons to switch to the selection fi eld “End” ...

  • Kathrein UFS 740sw - page 47

    47 When all settings have been made, press the  button to save the recording settings. Y ou can view the scheduled recording in the recording schedule view of the EPG (see item “Recording schedule”). RECORD USER-DEFINED Use the  buttons to select the recording mode “user-de fi ned” (see screenshot below). Use the  buttons to ...

  • Kathrein UFS 740sw - page 48

    48 When all settings have been made, press the  button to save the recording settings. Y ou can view the scheduled recording in the recording schedule view of the EPG (see item “Recording schedule”). SERIES RECORDING Use the  buttons to select the recording mode “Series recording”. In series recording the start and fi nish of reco ...

  • Kathrein UFS 740sw - page 49

    49 EPG - ELECTRONIC PROGRAMME GUIDE VIEW RECORDING SCHEDULE The recording schedule view can be called up at any time in EPG by pressing the red button. The recording schedule view shows you all the recordings that are scheduled. The  buttons allow the recordings to be sorted into “once-only recording” or “Repeating” recordings. The cu ...

  • Kathrein UFS 740sw - page 50

    50 COMMON INTERF ACE Always follow the operating instructions from your Pay-TV provider and the instructions supplied with the Smartcard and the CA module! Smartcards and CA modules are not included with this product! The cards and modules are issued by the respective Pay TV providers, and contain the subscriber data and details of the channels for ...

  • Kathrein UFS 740sw - page 51

    51 Y ou can fi nd out which Conditional Access modules are in the CI slots on the UFS 740sw and which Smartcard is in which CA module from the “Mainmenu” under “Settings”, and the “Common Interface” menu. Con fi rmation is by pressing the  button. Use the  buttons to select one of the two slots in which the CA module is locat ...

  • Kathrein UFS 740sw - page 52

    52 VIDEOTEXT (TELETEXT) This symbol in the channel noti fi cation shows you whether Videotext/T eletext is available for the selected channel. When you press the  button, the receiver processes the videotext/T eletext service data for your TV set to display , even when the signal is encrypted. During the scan, the page which is being searched f ...

  • Kathrein UFS 740sw - page 53

    53 EDIT CHANNEL LIST Select the “Edit TV -Channellist” menu using the menu button  , the  buttons on the main menu and  . When the menu is called up, the standard setting is for the receiver to show the “All Satellites” channel list with all channels available on the satellites that are being received. SELECTION OF THE LIST/CHAN ...

  • Kathrein UFS 740sw - page 54

    54 EDITING LISTS/CHANNELS When you have selected the channel or channel list to be edited, press the  (red dot) button to call up the edit menu. Y ou have the following edit options: - Move: Channel can be moved within the current list to another channel slot - Delete: Delete the channel from the current list - Skip: Channel will be skipped when ...

  • Kathrein UFS 740sw - page 55

    55 DELETE CHANNELS Use the  buttons to select the channel to be deleted from the current channel list. Press the  button to call up the edit menu and use the  buttons to select the “Delete” function. Con fi rm the command by pressing the  button. EDIT CHANNEL LIST SKIP CHANNELS Use the  buttons to select the channel to ...

  • Kathrein UFS 740sw - page 56

    56 BLOCK CHANNELS Use the  buttons to select the channel to be blocked from the current channel list. Press the  button to call up the edit menu and use the  buttons to select the “Lock” function. Con fi rm the command by pressing the  button. you are now prompted to enter the PIN code (factory default setting: 0000). The cha ...

  • Kathrein UFS 740sw - page 57

    57 EDIT CHANNEL LIST EDIT F A VOURITES LISTS When you have selected the favourite list to be edited (called up using the (red) button and selected using the  buttons), press the  (red dot) button to call up the edit menu. Y ou have the following edit options: - Remove from the Favourites List: The channel will be removed from the Favourite ...

  • Kathrein UFS 740sw - page 58

    58 BLOCK CHANNELS Use the  buttons to select the channel to be blocked in the Favourites List you have selected. Press the  button to call up the edit menu and use the  buttons to select the “Lock” function. Con fi rm the command by pressing the  button. you are now prompted to enter the PIN code (factory default setting: 000 ...

  • Kathrein UFS 740sw - page 59

    59 CHANNEL SEARCH (CHANNEL SCAN) Select the “Search Channels” menu using the menu button  , the  buttons on the main menu and the  button. Y ou have three options for a channel scan: - Automatic scan - all transponders for the satellite you selected will be scanned - Manual scan - only the selected transponder for the satellite you ...

  • Kathrein UFS 740sw - page 60

    60 Satellite Select the satellite to be scanned, using the  buttons. Make sure your reception system is aligned to the selected satellite. Y ou can scan only one satellite at a time. If you have connected a multi-feed reception system (e.g. reception of ASTRA 19.2° East and HOTBIRD 13° East), you must repeat this procedure once for each sat ...

  • Kathrein UFS 740sw - page 61

    61 Newly found channels are identi fi ed with the designation “New” after the channel name. After completion of the scan, you will see the following message (example): Press the  button. Y ou will be asked whether you wish to save the changes or not. Selection is performed using the  buttons and is con fi rmed using the  button. I ...

  • Kathrein UFS 740sw - page 62

    62 CHANNEL SEARCH (CHANNEL SCAN) The  buttons allow you to select different sets of parameters for the scan. Satellite Use the  buttons to select the satellite on which the transponder you wish to scan is located. Make sure your reception system is aligned to the selected satellite. Y ou can scan only one transponder at a time. If you w ...

  • Kathrein UFS 740sw - page 63

    63 Press the  button. Y ou will be asked whether you wish to save the changes or not. Selection is performed using the  buttons and is con fi rmed using the  button. If you select “Y es, save changes”, the newly found channels will be added to the end of the channel list. Then press the  button to exit the menu. The channel list ...

  • Kathrein UFS 740sw - page 64

    64 Press the  button to move to the next selection item. T ransponder frequency Use the  buttons or the keypad to select the transponder frequency on which the channel being sought is transmitted. At the bottom right of the screen display , the receiver shows the current signal strength and signal quality of the selected transponder . Pres ...

  • Kathrein UFS 740sw - page 65

    65 P ARENT AL CONTROL Select the “Parental Control” menu using the menu button  , the  buttons on the main menu and  . Y ou are now prompted to enter the PIN code (factory default setting: 0000). After entering the PIN using the keypad you are shown the following display: Select the parameters to be changed using the  buttons. ...

  • Kathrein UFS 740sw - page 66

    66 SETTINGS The selected menus, sub-menus and positions, as well as the parameters to be set, are each highlighted in colour . The menus are self-explanatory to a great extent. Pay attention to the bar at the bottom of the on-screen display! This provides hints on what to do next. Select the “Settings” menu using the menu button  , the ? ...

  • Kathrein UFS 740sw - page 67

    67 Here you can use the  buttons to select the type of video signal at the TV Scart socket. Select the signal that your TV set can process. When doing this, refer to the operating instructions for your TV set! • Composite baseband signal (colour/picture/blanking/synchronous signal) • RGB – Red/Green/Blue signal or • Y/C – S-V ideo s ...

  • Kathrein UFS 740sw - page 68

    68 Here you can use the  buttons to select the type of video signal at the VCR Scart socket. Select the signal that your external recorder can process. When doing this, refer to the operating instructions for your recorder! • Composite baseband signal (colour/picture/blanking/synchronous signal) • Y/C – S-V ideo signal (luminance/chromi ...

  • Kathrein UFS 740sw - page 69

    69 SETTINGS Use the  buttons to select the time after which you want the on-screen channel message display to be automatically cancelled. The selections available are “Of f”, 1, 2, 3, 4, 5 or 6 seconds. DISPLA Y DURA TION OF CHANNEL MESSAGE Use the  buttons (On/Off) to specify whether the volume bar is displayed when adjusting the v ...

  • Kathrein UFS 740sw - page 70

    70 SETTINGS DA TE AND TIME COMMON INTERF ACE See “Common Interface” section ANTENNA CONFIGURA TION See “First Installation” section, pages 15ff Set Local Time Use the  buttons to set the time zone variation from UTC (formerly GMT) (e.g. for Germany +1 hour). Use the  buttons to switch to the “Automatic clock change” fi eld. ...

  • Kathrein UFS 740sw - page 71

    71 SER VICE MENU Select the “Service” menu using the menu button  , the  buttons on the main menu and  . The following display appears: Current SW V ersion Channel list status Last update run Hardware version Start of the warranty period ² ) Software and hardware version CAP ¹ ) UPDA TING SOFTW ARE The receiver checks in standby m ...

  • Kathrein UFS 740sw - page 72

    72 SER VICE MENU UPDA TE Software Use the  buttons (No/Y es) to select whether you wish to load the new software that is available. If you are unsure whether you wish to load the new software, you can initially set the reply to “No”. If you do agree to the changes, you can then proceed to download the software. Channel list Select the req ...

  • Kathrein UFS 740sw - page 73

    73 F ACTOR Y DEF AUL T Y ou can select the “Service” menu using the  menu button, the  buttons in the main menu and  . Use the  buttons to switch to “Load factory default settings” and to call them up, press the  button. The following display appears: Press the  button to load the factory default settings. The channe ...

  • Kathrein UFS 740sw - page 74

    74 CONNECTING UP THE VIDEO/PVR For details of how to connect your external recorder to the receiver refer to the connection diagram provided at the end of this manual and the instructions for the external recorder . In order to make a PVR recording (Record), the satellite receiver must be switched on or the timers must be pre-programmed (see “EPG ...

  • Kathrein UFS 740sw - page 75

    75 USING THE FRONT P ANEL If you have misplaced your remote control, or if the batteries are empty , you can still operate your receiver from the front panel. BACKUP OPERA TION There are three buttons on the front of the receiver . TV/R button: Pressing the TV/R button switches the receiver from TV mode to radio mode. Pressing the TV/R button a sec ...

  • Kathrein UFS 740sw - page 76

    76 TECHNICAL APPENDIX FEA TURES  Reception of digital TV and radio satellite programmes  4,000 channel memory positions  16-character alphanumeric display with status icons for indication of channel names and transmitter information  Common interface for two CA modules ¹ )  Kathrein Convenience EPG with timer programming ² )  Gu ...

  • Kathrein UFS 740sw - page 77

    77 TECHNICAL APPENDIX T ype UFS 740sw Order no./colour 20210087/black RF properties Input frequency range MHz 950-2150 Input level range dBµV 44-83 Reception threshold (EB/NO) dB < 4.5 TV system, video Modulation, FEC, demultiplexer DVB-S standard Video resolution CCIR 601 (720 x 576 lines) Input data rate MSymb/s 2-45 Video decryption MPEG-1 a ...

  • Kathrein UFS 740sw - page 78

    78 Signal Pin no. TV VCR/AUX Right audio output 1 X X Right audio input 2 X Left audio output 3 X X Audio earth 4 X X Blue earth 5 X X Audio left input 6 X Blue signal 7 X X Switching voltage 8 X X Green earth 9 X X Data signal 10 Green signal 1 1 X X Data signal 12 Red earth 13 X X Data earth 14 Red signal (C) 15 X X Blanking signal 16 X X Video e ...

  • Kathrein UFS 740sw - page 79

    79 Scart Scart Digitalton AC 3 optisch/elektrisch Infrarot-Empfänger (optional) LW L CAP 900 CONNECTION EXAMPLE TECHNICAL APPENDIX Dolby digital system Digital audio AC 3 optical/electrical Infra-red receiver (optional) Hi- fi system ...

  • Kathrein UFS 740sw - page 80

    80 TECHNICAL APPENDIX EXAMPLES single-cable systems EXR 501/551/552 Single-cable switching matrices * ) The receiver must be programmed for single-cable commands ** ) Overvoltage protection KAZ 1 1/KAZ 12 Sat IF 4 x single or 2 x twin receiver ...

  • Kathrein UFS 740sw - page 81

    81 EXU 908 Single-cable matrix * ) The receiver must be programmed for single-cable commands ** ) Overvoltage protection KAZ 1 1/KAZ 12 Sat IF 2 x Quatro LNB UAS 484/584 TECHNICAL APPENDIX ...

  • Kathrein UFS 740sw - page 82

    82 UAS 481 Single-cable feed system TECHNICAL APPENDIX * ) The receiver must be programmed for single-cable commands ** ) Overvoltage protection KAZ 1 1/KAZ 12 ...

  • Kathrein UFS 740sw - page 83

    83 TECHNICAL APPENDIX EXR 1581/2581 Single-cable matrices * ) The receiver must be programmed for single-cable commands ** ) Overvoltage protection KAZ 1 1/KAZ 12 Sat IF ...

  • Kathrein UFS 740sw - page 84

    84 SHORT TECHNICAL GUIDE DISEQC™ DiSEqC™ (Digital Satellite Equipment Control) is a communication system between a satellite receiver (master) and the peripheral satellite components (slaves), such as LNBs, multi-switches, rotating antenna systems. It is a single master/multi-slave system, i.e. there is only ever one master in the satellite sys ...

  • Kathrein UFS 740sw - page 85

    85 PID The PID (Packet IDenti fi cation) number is an identi fi cation number for video signals and audio signals in the digital data stream of DVB-MPEG-2 signals. The receiver uses the PID number to create a unique assignment for the video and audio data transmission. The PCR PID is the identi fi cation number for the synchronisation signal. Th ...

  • Kathrein UFS 740sw - page 86

    86 SHORT TECHNICAL GUIDE AC 3 Output for Dolby Digital signal Audio output Sound output on the receiver A V programme pos. Preferred programme position on TV set for Scart input CA Conditional Access (for decoding of encrypted programmes) CI Internationally standardised interface for CA modules Decoder Decoder for Pay TV DiSEqC™ Control system be ...

  • Kathrein UFS 740sw - page 87

    87 TROUBLESHOOTING In the event of a malfunction, fi rst check all the cable connections and operating states: 1. Receiver and TV set power plugs are connected to wall socket 2. Antenna cables on receiver input 3. Receiver and TV set correctly connected by a Scart or cinch cable 4. Audio connections are made to Hi-Fi or Dolby Digital system as app ...

  • Kathrein UFS 740sw - page 88

    Internet: http://www .kathrein.de KA THREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 P .O. Box 100 444 • 83004 Rosenheim GERMANY 936.3103/B/0209/ZWT - T echnical data subject to change. ...

Manufacturer Kathrein Category Satellite TV System

Documents that we receive from a manufacturer of a Kathrein UFS 740sw can be divided into several groups. They are, among others:
- Kathrein technical drawings
- UFS 740sw manuals
- Kathrein product data sheets
- information booklets
- or energy labels Kathrein UFS 740sw
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kathrein UFS 740sw.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kathrein UFS 740sw, service manual, brief instructions and user manuals Kathrein UFS 740sw. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kathrein UFS 740sw.

Similar manuals

A complete manual for the device Kathrein UFS 740sw, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kathrein UFS 740sw by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kathrein UFS 740sw.

A complete Kathrein manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kathrein UFS 740sw - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kathrein UFS 740sw, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kathrein UFS 740sw, that we can find in the current document
3. Tips how to use the basic functions of the device Kathrein UFS 740sw - which should help us in our first steps of using Kathrein UFS 740sw
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kathrein UFS 740sw
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kathrein UFS 740sw in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kathrein UFS 740sw?

Use the form below

If you did not solve your problem by using a manual Kathrein UFS 740sw, ask a question using the form below. If a user had a similar problem with Kathrein UFS 740sw it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)