English dropdown-ico

Manual Agilent Technologies ES

63 pages 1.34 mb
Download

Go to site of 63

Summary
  • Agilent Technologies ES - page 1

    Installation and Quick Start Guide 8753ET/ES Network Analyzers P art Number: 08753-90471 Printed in USA Print Date: F ebruary 2001 Supersedes: May 2000 ...

  • Agilent Technologies ES - page 2

    ii Notice The information contained in this document is subject to change without notice . Agilent T echnologies makes no w arranty of any kind with regard to this material, including but not limited to , the implied warranties of merc hantability and fitness for a particular purpose. Agilent T ec hnologies shall not be liable for errors contained ...

  • Agilent Technologies ES - page 3

    iii Certification Agilent T echnologies Company certifies that this product met its published specifications at the time of shipment from the factory . Agilent T echnologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and T echnology , to the extent allowed by the Instit ...

  • Agilent Technologies ES - page 4

    iv General Safety Considerations W ARNING F or continued protection against fire hazard replace line fuse only with same type and rating (115V operation: T 5A 125V UL/ 230V operation: T 4A H 250V IEC). The use of other fuses or material is prohibited. W ARNING This is a Safety Class I product (provided with a protective earthing ground incorporate ...

  • Agilent Technologies ES - page 5

    v Documentation Map The Installation and Quick Start Guide provides procedures for installing , configuring , and verifying the operation of the analyzer . It also will help you familiarize yourself with the basic operation of the analyzer . The User’ s Guide shows how to make measurements , explains commonly-used features , and tells you how to ...

  • Agilent Technologies ES - page 6

    Contents Contents-vii 1. Installing Y our Analyzer Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 STEP 1. V erify the Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 STEP 2. F amiliarize Y ...

  • Agilent Technologies ES - page 7

    1-1 1 Installing Y our Analyzer ...

  • Agilent Technologies ES - page 8

    1-2 Chapter 1 Installing Y our Analyzer Introduction Introduction This chapter shows you how to install your analyzer and confirm the correct operation, by following the steps below: 1. V erify the shipment. 2. F amiliarize yourself with the analyzer front and rear panels . 3. Meet electrical and environmental requirements . 4. Configure the anal ...

  • Agilent Technologies ES - page 9

    Chapter 1 1-3 Installing Y our Analyzer STEP 1. V erify the Shipment STEP 1. V erify the Shipment NO TE If your analyzer was damaged during shipment, contact your nearest Agilent T echnologies office or sales representative. A list of Agilent T echnologies sales and service offices is provided in T able 2-1 on page 2-28 . ES models only: the PORT ...

  • Agilent Technologies ES - page 10

    1-4 Chapter 1 Installing Y our Analyzer STEP 1. V erify the Shipment 3. V erify that all the accessories ha ve been included with the analyzer . Item Number Part Number Description 1 08753-90471 Installation and Quick Start Guide 2 08753-90472 User's Guide 3 08753-90473 Reference Guide 4 08753-90475 Programmer’s Guide 5 08753-90469 CD-ROM 6 ...

  • Agilent Technologies ES - page 11

    Chapter 1 1-5 Installing Y our Analyzer STEP 2. Familiarize Y ourself with the Analyzer Front and Rear P anels STEP 2. F amiliarize Y ourself with the Analyzer F ront and Rear P anels Analyzer Front P anel CA UTION Do not mistake the line switch for the disk eject button. See the figure below . If the line switch is mistakenly pushed, the instrume ...

  • Agilent Technologies ES - page 12

    1-6 Chapte r 1 Installing Y our Analy z er STEP 2. F amiliarize Y ou r self with the Ana l yzer F r ont and Rear P anels Analyzer Rear P anel 1 10 MHZ REFERENCE ADJUST 1 2 1 0 MH Z PRECISIO N REFERENCE OUTPUT 1 3 F an 4 Line voltage selector switch 5 P ower cord receptacl e , with fuse 6 KEYBOARD input (mini-DIN) 7 RS-232 interface 8 P ARALLEL inte ...

  • Agilent Technologies ES - page 13

    Chapter 1 1-7 Installing Y our Analyzer STEP 3. Meet Electrical and En vironmental Requirements STEP 3. Meet Electrical and Environmental Requirements 1. Set the line-voltage selector to the position that corresponds to the AC power source. 2. Ensure the available AC power source meets the following requirements: • 90–132 V AC • 47–66 Hz / ...

  • Agilent Technologies ES - page 14

    1-8 Chapter 1 Installing Y our Analyzer STEP 3. Meet Electrical and En vironmental Requirements 5. Ensure there are at least six inches of clearance between the sides and back of either the stand-alone analyzer or the system cabinet. CA UTION The environmental temperature must be 4 ° C less than the maximum operating temperature of the analyzer fo ...

  • Agilent Technologies ES - page 15

    Chapter 1 1-9 Installing Y our Analyzer STEP 4. Configure the Analyzer STEP 4. Configure the Analyzer This step shows you how to set up your particular analyzer configuration. • standard configuration • Option 1D5 configuration − high stability frequency reference • printer or plotter configuration • rack-mount configuration ...

  • Agilent Technologies ES - page 16

    1-10 Chapter 1 Installing Y our Analyzer STEP 4. Configure the Analyzer T o Configure the Standard Analyzer T o Configure an Analyzer with a High Stability Frequency Reference (Option 1D5) Connect test port cables and optional adapters if you are using other connector types. Connect the jumper cable on the analyzer rear panel as shown. ...

  • Agilent Technologies ES - page 17

    Chapter 1 1-11 Installing Y our Analyzer STEP 4. Configure the Analyzer T o Configure the Analyzer with Printers or Plotters 1. Connect your printer or plotter to the corresponding interface. 2. If you are using the parallel interface, press and toggle until your choice of or appears. If you choose: the parallel port is dedicated for normal copy ...

  • Agilent Technologies ES - page 18

    1-12 Chapter 1 Installing Y our Analyzer STEP 4. Configure the Analyzer 3. Press . Then, depending on your printer/plotter device, c hoose either or . Or , if you are plotting your files to disk, press . 4. Press the key that corresponds to your printer or plotter interface: , (parallel port), or (serial port). NO TE The plotter menu is shown as ...

  • Agilent Technologies ES - page 19

    Chapter 1 1-13 Installing Y our Analyzer STEP 4. Configure the Analyzer 5. If you will be using the serial port, adjust the analyzer's baud rate until it is equal to the baud rate set on the peripheral by pressing or and the and front panel keys. NO TE The plotter menu is shown as an example. It will only appear if you select . Y ou can set t ...

  • Agilent Technologies ES - page 20

    1-14 Chapte r 1 Installing Y our Analy z er STEP 4. Configure the Ana l yzer 7. If you will be creating a plot of the data, toggle until your choice of or appear s . • Choose for a pen plotte r . • Choose for a PCL5 compatible printe r . 1 8. If you will be using a printe r , toggle until your printer choice 1 appear s . • Choose your printe ...

  • Agilent Technologies ES - page 21

    Chapter 1 1-15 Installing Y our Analyzer STEP 4. Configure the Analyzer 9. Press to begin setting and activating the time stamp feature so the analyzer places the time and date on your hardcopies and disk directories. 10. Press each of the following softkeys to set the date and time, followed by . 11. Press when the time is exactly as you have set ...

  • Agilent Technologies ES - page 22

    1-16 Chapter 1 Installing Y our Analyzer STEP 4. Configure the Analyzer T o Configure the Analyzer for Bench T op or Rack Mount Use There are three kits available for the analyzer: • instrument front handles kit (standard: part number 5062-9229) • cabinet flange kit without front handles (Option 1CM: part number 5062-9216) • cabinet flang ...

  • Agilent Technologies ES - page 23

    Chapter 1 1-17 Installing Y our Analyzer STEP 4. Configure the Analyzer T o Attach Front Handles to the Analyzer (Standard) 1. Ensure that the front handle kit is complete. 2. Remove the side trim strips. • (2) front handles • (6) screws • (2) trim strips NO TE If any items are damaged or missing from the kit, contact the nearest Agilent T e ...

  • Agilent Technologies ES - page 24

    1-18 Chapter 1 Installing Y our Analyzer STEP 4. Configure the Analyzer T o Attach Cabinet Flanges without Front Handles to the Analyzer (Option 1CM) 1. Ensure that the cabinet flange kit is complete. 2. Remove side trim strips . • (2) cabinet mount flanges • (6) screws 3. Attach the cabinet flanges to the sides of the front panel using thr ...

  • Agilent Technologies ES - page 25

    Chapter 1 1-19 Installing Y our Analyzer STEP 4. Configure the Analyzer T o Attach Cabinet Flanges with Front Handles to the Analyzer (Option 1CP) 1. Ensure that the cabinet flange kit with handles is complete. 2. Remove the side trim strips. • (2) cabinet mount flanges • (2) front handles • (6) screws 3. Attach the cabinet mount flanges ...

  • Agilent Technologies ES - page 26

    1-20 Chapter 1 Installing Y our Analyzer STEP 5. V erify the Analyzer Operation STEP 5. V erify the Analyzer Operation The following procedures show you how to check your analyzer for correct operation: • viewing installed options • initiating self-test • running operator's check • testing transmission mode • testing reflection mode ...

  • Agilent Technologies ES - page 27

    Chapter 1 1-21 Installing Y our Analyzer STEP 5. V erify the Analyzer Operation T o View the Installed Options 1. Cycle the AC power using the LINE switch, or press . 2. Locate the serial number and configuration options. Compare them to the shipment documents. System SERVICE MENU FIRMW ARE REVISION ...

  • Agilent Technologies ES - page 28

    1-22 Chapter 1 Installing Y our Analyzer STEP 5. V erify the Analyzer Operation T o Initiate the Analyzer Self-T est 1. Cycle the AC power using the LINE switch. 2. W atch for the following indications that the analyzer is operating correctly: ...

  • Agilent Technologies ES - page 29

    Chapter 1 1-23 Installing Y our Analyzer STEP 5. V erify the Analyzer Operation T o Run the Operator's Check 1. Connect the equipment as shown. 2. Press . F ollow the prompts shown on the analyzer display and then press . 3. ET models only: Press . F ollow the prompts shown on the analyzer display and then press . 3. ES models only: Press . F ...

  • Agilent Technologies ES - page 30

    1-24 Chapter 1 Installing Y our Analyzer STEP 5. V erify the Analyzer Operation T o T est the Transmission Mode 1. Connect the equipment as shown and press . 2. Check the forw ard transmission mode for channel 2 by pressing or . NO TE The test port return cable should have low-loss characteristics to avoid a degradation in frequency response at hig ...

  • Agilent Technologies ES - page 31

    Chapter 1 1-25 Installing Y our Analyzer STEP 5. V erify the Analyzer Operation T o T est the Reflection Mode 1. Connect the equipment as shown and press . 2. Look at the measurement trace displayed on the analyzer . It should be similar to the trace below . 3. ES models only: Check the reverse reflection mode for channel 1 by pressing . The meas ...

  • Agilent Technologies ES - page 32

    1-26 Chapter 1 Installing Y our Analyzer STEP 6. Back Up the EEPR OM Disk STEP 6. Back Up the EEPROM Disk Description Correction constants are stored in EEPROM on the A9 controller assembly . The advantage of having an EEPROM backup disk is the ability to store all the correction-constant data to a new or repaired A9 assembly without having to reru ...

  • Agilent Technologies ES - page 33

    Chapter 1 1-27 Installing Y our Analyzer STEP 6. Back Up the EEPR OM Disk 5. Press . Use the front panel knob and the softkey to rename the file “FILE00” to “N 12345 ” where 12345 represents the last 5 digits of the instrument's serial number . (The first character in the file name must be a letter .) When finished, press . 6. Labe ...

  • Agilent Technologies ES - page 34

    2-1 2 Quick Start: Learning How to Make Measurements ...

  • Agilent Technologies ES - page 35

    2-2 Chapter 2 Quick Start: Lear ning How to Make Measurements Introduction Introduction The information and procedures in this chapter teach you how to make measurements and what to do if you encounter a problem with your analyzer . The following sections are included: • Front P anel • Measurement Procedure • Learning to Make Transmission Mea ...

  • Agilent Technologies ES - page 36

    Chapter 2 2-3 Quick Start: Lear ning How to Make Measurements Analyzer Front P anel Analyzer F ront P anel CA UTION Do not mistake the line switch for the disk eject button. See the figure below . If the line switch is mistakenly pushed, the instrument will be turned off , losing all settings and data that have not been saved. Figure 2-1 The Analy ...

  • Agilent Technologies ES - page 37

    2-4 Chapter 2 Quick Start: Lear ning How to Make Measurements Analyzer Front P anel 9. ACTIVE CHANNEL keys. The analyzer has four independent display channels . These keys allow you to select the active channel. Then any function you enter applies to this active channel. Notice that the light next to the current active channel’ s key is illuminat ...

  • Agilent Technologies ES - page 38

    Chapter 2 2-5 Quick Start: Lear ning How to Make Measurements Measurement Procedure Measurement Procedure This is a general measurement procedure that is used throughout the guide to illustrate the use of the analyzer . Step 1. Choose measurement parameters with your test device connected • Press the key to return the analyzer to a known state. ? ...

  • Agilent Technologies ES - page 39

    2-6 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make T ransmission Measurements Learning to Make T ransmission Measurements This example procedure shows you how to measure the transmission response of a 175 MHz bandpass filter . The measurement parameters listed are unique to this particular test device. F or further meas ...

  • Agilent Technologies ES - page 40

    Chapter 2 2-7 Quick Start: Lear ning How to Make Measurements Learning to Make T ransmission Measurements Step 2. P erform a measurement calibration 1. Disconnect your test device from the analyzer . 2. Connect a “thru” between the measurement cables , as shown in Figure 2-3 . Include all the adapters that you will use in your device measuremen ...

  • Agilent Technologies ES - page 41

    2-8 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make T ransmission Measurements Step 3. Measure the device Measuring Insertion Loss 1. Reconnect your test device as in Figure 2-2. 2. Reposition the measurement trace for the best view . This can be done by pressing and, if necessary , adjusting the reference level, referenc ...

  • Agilent Technologies ES - page 42

    Chapter 2 2-9 Quick Start: Lear ning How to Make Measurements Learning to Make T ransmission Measurements Step 4. Output measurement results This example procedure shows how to output (store) measurement results to a disk. F or more information on creating a hardcopy of the measurement results , refer to the "Printing , Plotting , and Saving M ...

  • Agilent Technologies ES - page 43

    2-10 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make T ransmission Measurements Measuring Other Transmission Characteristics Using the analyzer marker functions , you can derive several important filter parameters from the measurement trace that is shown on the analyzer display . Measuring 3 dB Bandwidth. The analyzer ca ...

  • Agilent Technologies ES - page 44

    Chapter 2 2-11 Quick Start: Lear ning How to Make Measurements Learning to Make T ransmission Measurements 5. Press and enter . The analyzer now calculates the bandwidth between − 6 dB power levels . 6. Press when you are finished with this measurement. WIDTH V ALUE − 6 x1 Marker MARKER all OFF ...

  • Agilent Technologies ES - page 45

    2-12 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make T ransmission Measurements Measuring Out-of-Band Rejection. 1. Press . The marker appears where you placed it during the bandwidth measurement. 2. Press . The marker automatically searches for the minimum point on the trace . The frequency and amplitude of this point, r ...

  • Agilent Technologies ES - page 46

    Chapter 2 2-13 Quick Start: Lear ning How to Make Measurements Learning to Make T ransmission Measurements Measuring P assband Flatness or Ripple. P assband flatness (or ripple) is the variation in insertion loss over a specified portion of the passband. Continue with the following steps to measure passband flatness or ripple. 1. Press (if neces ...

  • Agilent Technologies ES - page 47

    2-14 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements Learning to Make Reflection Measurements This example procedure shows you how to measure the reflection response of a 175 MHz bandpass filter . The measurement parameter values listed are unique to this particular test device. F or further me ...

  • Agilent Technologies ES - page 48

    Chapter 2 2-15 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements Step 1. Choose measurement parameters with your test device connected 1. Press the key to return the analyzer to a known state. 2. Connect your test device as shown in Figure 2-8 . If using a load, make sure it has the correct characteristic imp ...

  • Agilent Technologies ES - page 49

    2-16 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements Step 2. Make a measurement calibration F ollow these instructions to perform an S 11 or reflection 1-port error correction: 1. Select a calibration kit that is appropriate to your device under test. Press . Choose the calibration kit that is ap ...

  • Agilent Technologies ES - page 50

    Chapter 2 2-17 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements 6. Press to complete the process . Step 3. Measure the device Measuring Return Loss. 1. Connect your device to PORT 1 or the REFLECTION port. 2. Press to reposition the trace. 3. Press to read the return loss from the analyzer display as shown i ...

  • Agilent Technologies ES - page 51

    2-18 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements Step 4. Output measurement results This step in the procedure shows you how to output the measurement results to a printer . F or in-depth information on creating a hardcopy of the measurement results , refer to the “Printing , Plotting , and ...

  • Agilent Technologies ES - page 52

    Chapter 2 2-19 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements Measuring Other Reflection Characteristics Y ou can derive several important filter parameters from the measurement shown on the analyzer display . The following set of procedures is a continuation of the previous reflection measurement proce ...

  • Agilent Technologies ES - page 53

    2-20 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements Measuring Standing W ave Ratio (SWR) Press so the analyzer shows the same data in terms of standing-wa ve-ratio (SWR), as shown in Figure 2-13 . Now the analyzer shows the measurement data in the unitless measure of SWR where SWR = 1 (perfect ma ...

  • Agilent Technologies ES - page 54

    Chapter 2 2-21 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements Measuring S 11 and S 22 or Reflection in a P olar F ormat. 1. Press . 2. Press to reposition the trace, as shown in F igure 2-14 . The analyzer shows the results of an S 11 or reflection measurement with each point on the polar trace correspon ...

  • Agilent Technologies ES - page 55

    2-22 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements Figure 2-14 Example S 11 or Reflection Measurement Trace in P olar F ormat Measuring S 11 and S 22 or Reflection in a Smith Chart F ormat. • Measuring Impedance The amount of power reflected from a device is directly related to the impedanc ...

  • Agilent Technologies ES - page 56

    Chapter 2 2-23 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements • Choose if you want the analyzer to show the linear magnitude and the phase of the reflection coefficient at the marker . • Choose if you w ant the analyzer to show the logarithmic magnitude and the phase of the reflection coefficient a ...

  • Agilent Technologies ES - page 57

    2-24 Chapter 2 Quick Start: Lear ning How to Make Measurements Learning to Make Reflection Measurements Figure 2-16 Example Admittance Measurement Trace ...

  • Agilent Technologies ES - page 58

    Chapter 2 2-25 Quick Start: Lear ning How to Make Measurements If Y ou Encounter a Problem If Y ou Encounter a Problem If you have difficulty when installing or using the analyzer , check the following list of commonly encountered problems and troubleshooting procedures . If the problem that you encounter is not in the following list, refer to add ...

  • Agilent Technologies ES - page 59

    2-26 Chapter 2 Quick Start: Lear ning How to Make Measurements If Y ou Encounter a Problem If the display lights, but the ventilation fan does not start: ❏ Check that the fan is not obstructed. T o check the fan, follow these steps: 1. Switch the LINE power to the off position. 2. Check that the fan blades are not jammed. ❏ Contact the nearest ...

  • Agilent Technologies ES - page 60

    Chapter 2 2-27 Quick Start: Lear ning How to Make Measurements If Y ou Encounter a Problem CA UTION If the error message: CAUTION: OVERLOAD ON INPUT X, POWER REDUCED appears on the analyzer display , too much source power is being applied at the input. In such a case , the input power will need to be reduced before the source power will remain on. ...

  • Agilent Technologies ES - page 61

    2-28 Chapter 2 Quick Start: Lear ning How to Make Measurements If Y ou Encounter a Problem T able 2-1 Agilent T echnologies Sales and Service Offices UNITED ST A TES Instrument Support Center Agilent T echnologies (800) 403-0801 EUROPEAN FIELD OPERA TIONS Headquarters Agilent T echnologies S .A. 150, Route du Nant-d’A vril 1217 Meyrin 2/ Geneva ...

  • Agilent Technologies ES - page 62

    Index Index 1 Numerics 3 dB bandwidth measuring , 2-10 6 dB bandwidth measuring , 2-11 A active channel keys location , 2-3 admittance measuring , 2-23 Agilent T echnologies Sales and Service Offices , 2-28 analyzer configuration , 1-9 – 1-19 attaching cabinet flanges with front handles , 1-19 attaching cabinet flanges without front handles , ...

  • Agilent Technologies ES - page 63

    2 Index Index measuring standing wave ratio (SWR) , 2-20 measuring the device , 2-17 outputting measurement results , 2-18 REFLECTION port location , 2-4 requirements electrical and environmental , 1-7 response function block keys location , 2-3 Return key , location , 2-3 return loss measuring , 2-17 S Sales and Service Offices , 2-28 shipment, v ...

Manufacturer Agilent Technologies Category TV Converter Box

Documents that we receive from a manufacturer of a Agilent Technologies ES can be divided into several groups. They are, among others:
- Agilent Technologies technical drawings
- ES manuals
- Agilent Technologies product data sheets
- information booklets
- or energy labels Agilent Technologies ES
All of them are important, but the most important information from the point of view of use of the device are in the user manual Agilent Technologies ES.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Agilent Technologies ES, service manual, brief instructions and user manuals Agilent Technologies ES. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Agilent Technologies ES.

Similar manuals

A complete manual for the device Agilent Technologies ES, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Agilent Technologies ES by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Agilent Technologies ES.

A complete Agilent Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Agilent Technologies ES - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Agilent Technologies ES, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Agilent Technologies ES, that we can find in the current document
3. Tips how to use the basic functions of the device Agilent Technologies ES - which should help us in our first steps of using Agilent Technologies ES
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Agilent Technologies ES
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Agilent Technologies ES in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Agilent Technologies ES?

Use the form below

If you did not solve your problem by using a manual Agilent Technologies ES, ask a question using the form below. If a user had a similar problem with Agilent Technologies ES it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)