English dropdown-ico

Manual Pelco MC3651H-2X

24 pages 0.22 mb
Download

Go to site of 24

Summary
  • Pelco MC3651H-2X - page 1

    ® INST ALLA TION/OPERA TION MC3651H-2 Series DSP Monochrome Camera English Español C1985M-E-ML (3/05) ...

  • Pelco MC3651H-2X - page 2

    2 C1985M-E-ML (3/05) ENGLISH Important Safeguards and W arnings Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should be done only by qualifi ed service and installation personnel. 2. Installation shall be done in accordance with all local and national electrical and mechanic ...

  • Pelco MC3651H-2X - page 3

    C1985M-E-ML (3/05) 3 ENGLISH Regulatory Notices This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate r ...

  • Pelco MC3651H-2X - page 4

    4 C1985M-E-ML (3/05) ENGLISH Camera Layout Figure 1. Camera Layout Installation LENS MOUNTING The camera can use a fixed iris, manual iris or auto iris lens. The camera is factory set for a CS-mount lens, but is easily adjusted for a C-mount lens. 1. C-Mount Lens Only - Rotate the back focus adjustment fully counterclockwise before installing the ...

  • Pelco MC3651H-2X - page 5

    C1985M-E-ML (3/05) 5 ENGLISH CAMERA MOUNTING Use a standard 1/4-20 screw (provided) with a maximum thread length of 3/8-inch (10 mm) for top or bottom camera mounting. The mount adapter may be fi tted to the top or bottom of the camera. The camera is shipped with the mount adapter located on the top of the camera. To change the mount adapter posit ...

  • Pelco MC3651H-2X - page 6

    6 C1985M-E-ML (3/05) ENGLISH AC operation only - If you are wiring more than one camera to the same transformer , connect one side of the transformer to the same terminal on all cameras, and connect the other side of the transformer to the remaining terminal on all cameras. Failure to connect all of the cameras the same way will cause the cameras t ...

  • Pelco MC3651H-2X - page 7

    C1985M-E-ML (3/05) 7 ENGLISH Lens Setup and Focus Procedures Video Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1V peak-to-peak). Switch the AGC ON. T o ...

  • Pelco MC3651H-2X - page 8

    8 C1985M-E-ML (3/05) ENGLISH Switch Settings Figure 6. DIP Switch Default Settings  BLC - Back Light Compensation OFF (Default setting) - Disables the BLC mode. BLC - Enables the BLC mode. If a bright backlight is present the subjects in the picture may appear dark or as a silhouette. BLC compensates for the bright backlight and enhances objects ...

  • Pelco MC3651H-2X - page 9

    C1985M-E-ML (3/05) 9 ENGLISH  NOR/SHP - Sharpness NOR (Default setting) - Sets the camera to normal sharpness mode. SHP - Enables the Sharpness mode. Enhances picture detail by increasing the aperture gain of the camera, sharpening the edges in the picture.  LC - Long Line Compensation OFF (Default setting) - Disables the Long Line Compensati ...

  • Pelco MC3651H-2X - page 10

    10 C1985M-E-ML (3/05) ENGLISH Camera Synchronization (AC Operation Only) When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera view is switched. T o eliminate vertical roll, adjust the phase control by synchronizing, or line-locking, the cameras to one another . Use the phase potentiometer locate ...

  • Pelco MC3651H-2X - page 11

    C1985M-E-ML (3/05) 11 ENGLISH Specifications GENERAL CCD Sensor 1/3-inch interline transfer Picture Elements MC3651H-2: 768 (H) x 494 (V) MC3651H-2X: 795 (H) x 596 (V) Sensing Area 6 mm diagonally Synchronize System INT/AC line lock Horizontal Resolution 570 TV lines Iris Control Electronic/passive Minimum Illumination 0.07 lux, 1/60-second shutte ...

  • Pelco MC3651H-2X - page 12

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products and the following fixed camera model ...

  • Pelco MC3651H-2X - page 13

    C1985M-E-ML (3/05) 13 ESP AÑOL Instrucciones de Seguridad y Advertencias Importantes Antes de instalar y usar este producto, tenga en cuenta las siguientes ADVERTENCIAS: 1. La instalación y servicio deben ser realizados solo por personal de instalación y servicio calificado. 2. La instalación se debe realizar de acuerdo con todos los códigos ...

  • Pelco MC3651H-2X - page 14

    14 C1985M-E-ML (3/05) ESP AÑOL A visos Reglamentarios Este equipo ha sido probado y se ha determinado que cumple con los límites de un dispositivo digital Clase B, según el apartado 15 de las reglamentaciones de la FCC. Esos límites están diseñados para brindar protección razonable contra interferencia peligrosa en una instalación residenci ...

  • Pelco MC3651H-2X - page 15

    C1985M-E-ML (3/05) 15 ESP AÑOL Composición de la Cámara Figura 1. Composición de la cámara Instalación MONTAJE DE LA LENTE La cámara puede utilizar lentes de iris fijo, manual o automático. La confi guración de fábrica de la cámara es para lentes de montura CS, pero se ajusta con facilidad a lentes de montura C. 1. Sólo para lentes de ...

  • Pelco MC3651H-2X - page 16

    16 C1985M-E-ML (3/05) ESP AÑOL MONTAJE DE LA CÁMARA Use un tornillo 1/4-20 estándar (suministrado) con una longitud de rosca máxima de 3/8 pulgada (10 mm) para montaje en la parte superior o inferior de la cámara. El adaptador de montura se puede colocar en la parte superior o inferior de la cámara. La cámara se envía con el adaptador de mo ...

  • Pelco MC3651H-2X - page 17

    C1985M-E-ML (3/05) 17 ESP AÑOL Sólo para suministro CA - Si desea conectar más de una cámara al mismo transformador , conecte un lado del transformador al mismo terminal en todas las cámaras, y conecte el otro lado del transformador al terminal restante en todas las cámaras. Si no conecta todas las cámaras de la misma manera, las cámaras po ...

  • Pelco MC3651H-2X - page 18

    18 C1985M-E-ML (3/05) ESP AÑOL Lente de iris automático de comando directo (CC) Coloque el interruptor selector de modo de lente en posición AIV . Coloque el interruptor ESC en posición ON. Use un destornillador adecuado para girar el potenciómetro de nivel de lente (consulte la Figura 1) totalmente en sentido horario. Después ajuste lentamen ...

  • Pelco MC3651H-2X - page 19

    C1985M-E-ML (3/05) 19 ESP AÑOL Configuración de Interruptores Figura 6. Configuración predeterminada  BLC - Compensación de contraluz OFF (configuración predeterminada) - Desactiva el modo BLC. BLC - Activa el modo BLC. Si hay contraluz brillante, los objetos en la imagen pueden aparecer oscuros o como una silueta. La función BLC aument ...

  • Pelco MC3651H-2X - page 20

    20 C1985M-E-ML (3/05) ESP AÑOL  NOR/SHP - Nitidez NOR (configuración predeterminada) - Configura la cámara en el modo de nitidez normal. SHP - Activa el modo Nitidez. Mejora el detalle de la imagen aumentando la ganancia de apertura de la cámara, dando más nitidez a los bordes de la imagen.  LC - Compensación de línea larga OFF (con? ...

  • Pelco MC3651H-2X - page 21

    C1985M-E-ML (3/05) 21 ESP AÑOL Sincronización de Cámara (Sólo para Suministro Ca) Al utilizar más de una fuente de suministro de energía de cámara, se puede producir un breve movimiento vertical de la imagen en el monitor cuando se cambia la vista de una cámara a otra. Para eliminar movimientos verticales de la imagen, ajuste el control de ...

  • Pelco MC3651H-2X - page 22

    22 C1985M-E-ML (3/05) ESP AÑOL Especificaciones GENERALES Sensor CCD T ransferencia interlineal de 1/3 pulgada Elementos de imagen MC3651H-2: 768 (H) x 494 (V) MC3651H-2X: 795 (H) x 596 (V) Área de sensor 6 mm diagonalmente Sistema de sincronización Sincronismo de línea INT/AC Resolución horizontal 570 líneas de TV Control de iris Electróni ...

  • Pelco MC3651H-2X - page 23

    INFORMACIÓN SOBRE GARANTÍA Y DEVOLUCIÓN DEL PRODUCTO GARANTÍA Pelco reparará o reemplazará, sin cargo, toda mercadería que se compruebe que tiene defectos de material o mano de obra, durante un período de un año a partir de la fecha de envío de la mercadería. Esta garantía contempla las siguientes excepciones: •Cinco años para los pr ...

  • Pelco MC3651H-2X - page 24

    United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco MC3651H-2X can be divided into several groups. They are, among others:
- Pelco technical drawings
- MC3651H-2X manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco MC3651H-2X
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco MC3651H-2X.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco MC3651H-2X, service manual, brief instructions and user manuals Pelco MC3651H-2X. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco MC3651H-2X.

Similar manuals

A complete manual for the device Pelco MC3651H-2X, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco MC3651H-2X by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco MC3651H-2X.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco MC3651H-2X - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco MC3651H-2X, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco MC3651H-2X, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco MC3651H-2X - which should help us in our first steps of using Pelco MC3651H-2X
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco MC3651H-2X
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco MC3651H-2X in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco MC3651H-2X?

Use the form below

If you did not solve your problem by using a manual Pelco MC3651H-2X, ask a question using the form below. If a user had a similar problem with Pelco MC3651H-2X it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)