English dropdown-ico

Manual Miller Electric CP-252TS

36 pages 1.23 mb
Download

Go to site of 36

Summary
  • Miller Electric CP-252TS - page 1

    Pro cesses Descrip ti on MIG (GMAW) W elding Flux Cored (FCA W ) W elding Arc Welding Power Source OM -259 177 743P June 2003 CP-302 and CP-252TS V isit our website at www.MillerWelds.com ...

  • Miller Electric CP-252TS - page 2

    Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog orindividual catalog sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .MillerW elds ...

  • Miller Electric CP-252TS - page 3

    The following term is used interchangeably throughout this manual: MIG = GMAW W ARNING T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Miller Electric CP-252TS - page 4

    ...

  • Miller Electric CP-252TS - page 5

    OM-259 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _nd_7/02 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown i n the adjoining symbols. Y Marks a special safety message. . Means “Note”; not safety related. This group of symbols means W arning! Watch ...

  • Miller Electric CP-252TS - page 6

    OM-259 Page 2 Arc rays from the w elding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld. ARC RA YS can burn eyes and skin. D Wear a welding helmet fitted with a proper shade of filter to protect your face and eyes when welding or watching (see ANSI Z49.1 and Z8 ...

  • Miller Electric CP-252TS - page 7

    OM-259 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit. F A ...

  • Miller Electric CP-252TS - page 8

    OM-259 Page 4 1-4. Principal Safety Standards Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, from American W elding Society , 550 N.W . LeJeune Rd, Miami FL 33126 (phone: 305-443-9353, website: www .aws.org). Recommended Safe Practices for the Preparation for W elding and Cut- ting of Containers and Piping , American Weldi ...

  • Miller Electric CP-252TS - page 9

    OM-259 Page 5 SECTION 1 − CONSIGNES DE SÉCURITÉ − À LIRE A V ANT UTILISA TION som _nd_fre 7/02 1-1. Signification des symboles Signifie « Mise en garde. Faire preuve de vigilance. » Cette procédure présente des risques identifiés par les symboles adjacents aux directives. Y Identifie un message de sécurité particulier . . Signifie « ...

  • Miller Electric CP-252TS - page 10

    OM-259 Page 6 Le rayonnement de l’arc génère des rayons visibles et invisibles intenses (ultraviolets et infrarouges) suscep- tibles de causer des brûlures oculaires et cutanées. Des étincelles sont projetées pendant le soudage. LES RA YONS DE L ’ARC peuvent cau- ser des brûlures oculaires et cuta- nées. D Porter un masque de soudage mu ...

  • Miller Electric CP-252TS - page 11

    OM-259 Page 7 1-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien de l’appareil. Risque D’INCENDIE OU D’EXPLO- SION D Ne pas placer l’appareil sur une surface inflam- mable, ni au − dessus ou à proximité d’elle. D Ne pas installer l’appareil à proximité de produits inflammables. D Ne pas surcha ...

  • Miller Electric CP-252TS - page 12

    OM-259 Page 8 1-4. Principales normes de sécurité Safety in W elding, Cutting, and Allied Processes, norme ANSI Z49.1, de l’American W elding Society , 550 N.W . LeJeune Rd, Miami FL 33126 (téléphone : (305) 443 − 9353, site Web : www .aws.org). Recommended Safe Practices for the Preparation for W elding and Cut- ting of Containers and Pipi ...

  • Miller Electric CP-252TS - page 13

    OM-259 Page 9 SECTION 2 − INST ALLA TION 2-1. Specifications Rated Open- Circuit Amperes Input at Rated Load Output, 50 or 60 Hz, Three-Phase Model Rated W elding Output Circuit V oltage Range DC 200 V 220 V 230 V 380 V 400 V 440 V 460 V 520 V 575 V KV A KW 250 Amp 250 A @ 35 V olts DC, 100% Duty Cycle 14 − 44 34.5 1.7* −− 30 1.4* −− ? ...

  • Miller Electric CP-252TS - page 14

    OM-259 Page 10 2-3. V olt-Ampere Curves va_curve1 4/95 − SA-180 902 / SA-180 901-B V olt-ampere curves show mini- mum and maximum voltage and amperage output capabilities of unit. Curves of other settings fall be- tween curves shown. A. 250 Ampere Models B. 300 Ampere Models CP302 MAX CP302 MIN ...

  • Miller Electric CP-252TS - page 15

    OM-259 Page 1 1 2-4. Dimensions And Weights Dimensions Di mens i ons A A 30 in (762 mm) Including lift eye B 23 in (584 mm) B C C 31 in (787 mm) Including strain relief D 27-1/2 in (699 mm) F G H E 3/4 in (19 mm) 4 Holes F 21-1/8 in (537 mm) G 1-1/8 in (29 mm) D H 7/16 in (1 1 mm) Dia W eight E 800 453-A / 801 530 Front 320 lb (145 kg) ...

  • Miller Electric CP-252TS - page 16

    OM-259 Page 12 2-5. Selecting A Location 1 Rating Label Use rating label to determine input power needs. Label located under front access door . 2 Line Disconnect Device Locate unit near correct input power supply . Y Special installation may be required where gasoline or volatile liquids are present − see NEC Article 51 1 or CEC Section 20. 2 18 ...

  • Miller Electric CP-252TS - page 17

    OM-259 Page 13 2-7. T ypical MIG Process Connections Using A V oltage-Sensing Wire Feeder Y W eld current can damage electronic parts in vehicles. Disconnect both battery cables before welding on a vehicle. Pl ace wor k cl amp as close t o the weld as possible. V oltage sensing wire feeders are used with constant current (CC) or constant voltage (C ...

  • Miller Electric CP-252TS - page 18

    OM-259 Page 14 2-8. Slope Selection (250 Ampere Model) Ref. ST-801 518-A Y Disconnect and lockout/tag- out input power before re- moving side panel. Lockout/tagging procedures con- sist of padlocking line disconnect switch in open position, removing fuses from fuse box, or shutting o ff and red-tagging circuit breaker or other disconnecting device. ...

  • Miller Electric CP-252TS - page 19

    OM-259 Page 15 2-9. Inductance Selection (300 Ampere Models) Y Disconnect and lockout/tag- out input power before re- moving side panel. Lockout/tagging procedures con- sist of padlocking line disconnect switch in open position, removing fuses from fuse box, or shutting o ff and red-tagging circuit breaker or other disconnecting device. 1 Stabilize ...

  • Miller Electric CP-252TS - page 20

    OM-259 Page 16 2-10. W eld Output T erminals And Selecting Cable Sizes Y ARC WELDING can cause Electromagnetic Interference. T o reduce possible interference, keep weld cables as short as possible, close together , and down low , such as on the floor . Locate welding operation 100 meters from any sensitive electronic equipment. Be sure this welding ...

  • Miller Electric CP-252TS - page 21

    OM-259 Page 17 2-12. Connecting T o 1 15 V olts AC Duplex Receptacle Ref. ST-801 380-B 1 1 15 V 15 A AC Receptacle RC9 Power is sh ared between RC9 an d remote 14 receptacle RC8. 2 Circuit Breaker CB1 3 Circuit Breaker CB2 CB 1 protects 1 15 volts ac portion of RC8 and RC9 from overload. CB2 protects 24 volts ac portion of RC8 from overload. Press ...

  • Miller Electric CP-252TS - page 22

    OM-259 Page 18 2-14. Placing Jumper Links Ref. ST-801 382 Check input voltage available at site. 1 Jumper Link Label Check label − only one is on unit. 2 Jumper Link Move jumper links to match input volt- age, and label on unit. . Tighten jumper link nuts to 25 in lb +/- 5 in lb. 2 1 200 VOL TS 230 VOL TS 460 VOL TS S-072 135-B L1 L2 L3 L1 L2 L3 ...

  • Miller Electric CP-252TS - page 23

    OM-259 Page 19 2-15. Connecting Input Power ST-800 103-B / Ref. ST -801 1 16 Y Disconnect and lockout/tagout input power before connecting input con- ductors from unit. Y Have only qualified persons make this installation. See rating label on unit and check input volt- age available at site. 1 Line Disconnect Device 2 Input Conductors 3 Grounding C ...

  • Miller Electric CP-252TS - page 24

    OM-259 Page 20 SECTION 3 − OPERA TION 3-1. Controls Ref. ST-801 380-B 1 Power Switch 2 Pilot Light Light is on when power is On. 3 Preset Indicator Light When light is on, the voltmeter displays preset welding voltage as selected by the V oltage Adjustment control. When light is of f, the voltmeter displays actual welding voltage while welding. Y ...

  • Miller Electric CP-252TS - page 25

    OM-259 Page 21 4-2. Overload Protection Y Disconnect and lockout/tagout input power before removing side panel. Lockout/tagging procedures consist of padlocking line disconnect switch in open position, removing fuses from fuse box, or shutting of f and red-tagging cir- cuit breaker or other disconnecting de- vice. 1 Fuse Panel Module Fuses F1 and F ...

  • Miller Electric CP-252TS - page 26

    OM-259 Page 22 4-3. T roubleshooting T rouble Remedy Completely inoperative; fan does not run. Place line disconnect switch in the On position (see Section 2-15 ). Check and replace open line fuse(s) (see Section 2-15 ). Check for proper jumper link positions (see Section 2-14 ). Check for proper input connections (see Section 2-15 ). No weld outpu ...

  • Miller Electric CP-252TS - page 27

    OM-259 Page 23 SECTION 5 − ELECTRICAL DIAGRAMS 212 993-A Figure 5-1. Circuit Diagram For 250 Ampere Model ...

  • Miller Electric CP-252TS - page 28

    OM-259 Page 24 212 994-A Figure 5-2. Circuit Diagram For 300 Ampere Models ...

  • Miller Electric CP-252TS - page 29

    OM-259 Page 25 Notes ...

  • Miller Electric CP-252TS - page 30

    OM-259 Page 26 SECTION 6 − P ARTS LIST Figure 6-1. Complete Assembly 801 383-J 1 2 3 4 5 40 6 7 8 9 10 11 12 13 14 15 39 44 43 42 41 Fig 6 − 3 − 17 1 36 37 38 19 20 35 34 33 32 31 28 27 26 25 24 23 22 21 29 Fig 6 − 2 − 30 ...

  • Miller Electric CP-252TS - page 31

    OM-259 Page 27 Quantity Description Part No. Dia. Mkgs. Item No. Figure 6-1. Complete Assembly 1 134 464 LABEL, warning general 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 179 430 P ANEL, side 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Miller Electric CP-252TS - page 32

    OM-259 Page 28 Quantity Description Part No. Dia. Mkgs. Item No. Figure 6-1 . Complete Assembly (continued) 37 036 585 ST ABILIZER, (302 models) 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 180 666 BRACKET , mtg PC board 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Miller Electric CP-252TS - page 33

    OM-259 Page 29 Description Part No. Dia. Mkgs. Item No. Figure 6-2. Panel, Front w/Components (continued) (Figure 6-1 Item 30) 8 CR2 186 162 RELA Y , encl 120V AC DPDT 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 R2 1 14 050 RESISTOR, WW fxd 10W 1K ohm 1 . . . . . . . . . . . . . . . . . ...

  • Miller Electric CP-252TS - page 34

    OM-259 Page 30 Figure 6-3. Rectifier Assembly Ref. 802 497-A 1 3 2 4 9 5 6 8 10 7 Figure 6-3. Rectifier Assembly (Figure 6-1 Item 17) Description Part No. Dia. Mkgs. Item No. 1 210 324 MOUNTING BOARD, rectifier 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 087 461 HEA T SINK 2 . . ...

  • Miller Electric CP-252TS - page 35

    Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 6/02 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor . The expertise o ...

  • Miller Electric CP-252TS - page 36

    PRINTED IN USA © 2003 Miller Electric Mfg. Co. 1/03 Miller Elect ric Mfg. Co. An Illinois T ool W orks Compan y 1635 West Spenc er S treet Applet on, W I 54914 USA International He adquarters − US A USA P hone: 920-735-4505 Aut o-At tended USA & C anada F A X: 920-735-4134 Int ernat ional FAX: 920-735-4125 European Headqua rters − United K ...

Manufacturer Miller Electric Category Welder

Documents that we receive from a manufacturer of a Miller Electric CP-252TS can be divided into several groups. They are, among others:
- Miller Electric technical drawings
- CP-252TS manuals
- Miller Electric product data sheets
- information booklets
- or energy labels Miller Electric CP-252TS
All of them are important, but the most important information from the point of view of use of the device are in the user manual Miller Electric CP-252TS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Miller Electric CP-252TS, service manual, brief instructions and user manuals Miller Electric CP-252TS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Miller Electric CP-252TS.

Similar manuals

A complete manual for the device Miller Electric CP-252TS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Miller Electric CP-252TS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Miller Electric CP-252TS.

A complete Miller Electric manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Miller Electric CP-252TS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Miller Electric CP-252TS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Miller Electric CP-252TS, that we can find in the current document
3. Tips how to use the basic functions of the device Miller Electric CP-252TS - which should help us in our first steps of using Miller Electric CP-252TS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Miller Electric CP-252TS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Miller Electric CP-252TS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Miller Electric CP-252TS?

Use the form below

If you did not solve your problem by using a manual Miller Electric CP-252TS, ask a question using the form below. If a user had a similar problem with Miller Electric CP-252TS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)