English dropdown-ico

Manual Husqvarna 96045001900

48 pages 2.49 mb
Download

Go to site of 48

Summary
  • Husqvarna 96045001900 - page 1

    YTH2348 Owner's Manual ...

  • Husqvarna 96045001900 - page 2

    2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine. • ...

  • Husqvarna 96045001900 - page 3

    3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off. They may fall off and be seriously injured or ...

  • Husqvarna 96045001900 - page 4

    4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ................................................................. 5-6 OPERA TION ...................................................... ...

  • Husqvarna 96045001900 - page 5

    5 UNAS SEMBLED P ARTS (2) Keys Slope Sheet Key (1) Oil Drain Tube AS SEMBL Y When right or left hand is mentioned in this man ual, it means when you are in the operating po si tion (seated be hind the steer ing wheel). TO REMOVE TRACTOR FROM CAR TON UNP ACK CARTON • Remove all accessible loose parts and parts cartons from carton. • Cut along da ...

  • Husqvarna 96045001900 - page 6

    6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled. See “TO LEVEL MOWER HOUSING? ...

  • Husqvarna 96045001900 - page 7

    7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF FUEL CHOKE MOWER HEIGHT REVERS ...

  • Husqvarna 96045001900 - page 8

    8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the applicable safety standards of the American Nati ...

  • Husqvarna 96045001900 - page 9

    9 OPERA TION Fig. 4 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles. F ...

  • Husqvarna 96045001900 - page 10

    10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4". The heights are measured from the ground to the blade tip with the engine not ...

  • Husqvarna 96045001900 - page 11

    11 S Fig. 10 OPERA TION REVERSE OPERA TION SYSTEM (ROS) (See Fig. 11) Y our tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position. WARNING: Backing up with t ...

  • Husqvarna 96045001900 - page 12

    12 CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to sep a ra tion and for ma tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. T o avoid engine problems, the fuel system should be emptied before stor age of 30 days or longer . Drain the ...

  • Husqvarna 96045001900 - page 13

    13 PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- vel oped during ...

  • Husqvarna 96045001900 - page 14

    14 MAINTENANCE T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when ...

  • Husqvarna 96045001900 - page 15

    15 MAINTENANCE Fig. 15 BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour . NO ...

  • Husqvarna 96045001900 - page 16

    16 MAINTENANCE TO CHANGE ENGINE OIL (See Figs. 16 and 17) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container . • Remove oil fill cap/dipstick. Be careful not to allow dir ...

  • Husqvarna 96045001900 - page 17

    17 CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine dam age from overheating. Clean with a wire brush or compressed air to re move dirt and stubborn dried gum fibers. AIR FIL TER Y our engine will not run properly using a dirty air filter . Service air cleaner more often under dusty conditions. See Engine Manual. EN ...

  • Husqvarna 96045001900 - page 18

    18 WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP” and remove key . • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug ...

  • Husqvarna 96045001900 - page 19

    19 SERVICE AND ADJUSTMENTS D C • A TT ACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with washer and retainer spring. • Repeat on opposite side of tractor . Fig. 26 NOTE: Be su re mower side suspension arms (A) are pointing forward before sliding mower under tractor . ? ...

  • Husqvarna 96045001900 - page 20

    20 H F J G E Fig. 27 M • Engage belt tension rod (K) on locking bracket (L). CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly . • Raise attachment lift lever to highest position. • If necessary , adjust gauge wheels before op er at ing mower as shown in the Operation section of this manual. Fig. 28 A C H ...

  • Husqvarna 96045001900 - page 21

    21 TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly . VISUAL SIDE- TO -SIDE ADJUSTMENT (See Fig. 30) • With all tires properly inflated and if your lawn appears unevenly cut, determ ...

  • Husqvarna 96045001900 - page 22

    22 TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 34) MOWER DRIVE BEL T REMOV AL • P ark tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Disengage belt tension rod (K) from lock bracket (L). CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly . • R ...

  • Husqvarna 96045001900 - page 23

    23 SERVICE AND ADJUSTMENTS TO REPL ACE MOTION DRIVE BEL T (See Fig. 35) P ark the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest. BEL T REMOV AL - • Remove mower (See “TO RE MOVE MOWER” in this section of manual). NOTE: Observe entire motion drive bel ...

  • Husqvarna 96045001900 - page 24

    24 SERVICE AND ADJUSTMENTS Fig. 37 WEAK OR DEAD BA TTERY FULL Y CHARGED BA TTERY REPL ACING BA TTERY (See Fig. 38) WARNING: Do not short battery ter mi nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery , remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be ...

  • Husqvarna 96045001900 - page 25

    25 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERL OCKS AND REL A YS Loose or damaged wiring may cause your tractor to run poorly , stop running, or prevent it ...

  • Husqvarna 96045001900 - page 26

    26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from t ...

  • Husqvarna 96045001900 - page 27

    27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. W ait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. W eak or dead battery . 5. Recharge or replace battery . 6. Dirty a ...

  • Husqvarna 96045001900 - page 28

    28 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged. Engine continues to run 1. F aulty operator-safety presence control system. 1. Check wiring, switc ...

  • Husqvarna 96045001900 - page 29

    29 NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOUR METER REGULA TOR CHASSIS HARNESS CONNECT OR (MA TING SIDE) D ASH HARNESS CONNECT OR (MA TING SIDE) LIGHT SWITCH HEADLIGHTS ST A TOR FUEL LINE FUEL S ...

  • Husqvarna 96045001900 - page 30

    30 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 101 40 71 34 With Service Minder Option 46 46 With 12V Outlet Option 59 103 16 42 T11S 102 29 105 ...

  • Husqvarna 96045001900 - page 31

    31 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 ELECTRICAL KEY P ART NO . NO. DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 41 41-26 Battery Box 16 532 17 61-38 Switch Interlock 21 532 18 37-59 Harness Socket Light 22 532 00 41-52 Bulb, Light #1156 24 532 40 02-53 Cable Battery 25 532 4 ...

  • Husqvarna 96045001900 - page 32

    32 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 CHASSIS 182 68 68 176 176 175 178 165 228 228 183 194 236 150 180 68 68 213 52 218 34 130 130 177 chassis-te x_69-gt-husq_r2 233 233 189 189 152 217 235 195 14 214 130 130 176 202 203 204 210 208 18 15 25 207 211 209 212 5 176 176 205 206 181 234 234 37 194 194 181 181 161 36 3 ...

  • Husqvarna 96045001900 - page 33

    33 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 CHASSIS 3 532 40 50-12 Logo 5 532 40 87-00 Dash 14 532 41 10-46 Hood 15 532 19 89-07 Lens LH 18 532 40 86-07 Grille Asm. 25 532 19 89-06 Lens RH 34 532 19 61-25 Plate Engine 36 817 06 05-12 Screw 5/16-18 x 3/4 37 532 41 86-73 F ender 52 873 68 05-00 Nut Lock 5/16-18 68 817 49 0 ...

  • Husqvarna 96045001900 - page 34

    34 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 DRIVE 52 51 170 171 225 125 drive-te x_K46_pedal_28 2 2 73 73 33 205 1 116 33 230 230 183 183 205 116 56 213 221 160 206 26 207 209 92 125 116 64 188 161 167 160 42 29 15 159 159 35 184 221 186 189 49 187 50 51 52 51 190 185 125 226 125 125 80 125 208 210 214 125 215 153 166 21 ...

  • Husqvarna 96045001900 - page 35

    35 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 DRIVE KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 - - - - - - - - - T ransaxle, TUFF TORQ K46 BT (Internal parts not available) 2 532 12 35-83 Key 15 819 13 13-16 W asher 13/32 x 13/16 x 16 Ga. 17 532 41 36-78 Spring, Brake 26 532 19 96-79 Spring Return Crui ...

  • Husqvarna 96045001900 - page 36

    36 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 ENGINE 28 113 110 109 111 1 29 SP ARK ARRESTER KIT 84 45 21 20 62 71 70 79 69 87 2 engine-te x_bs-2cyl_30 81 82 37 28 37 12 11 41 42 85 9 90 18 15 ...

  • Husqvarna 96045001900 - page 37

    37 KEY P ART NO . NO. DESCRIPTION 1 - - - - - - Engine Briggs Model No. 445577 2 532 14 97-23 Muffler 9 532 19 43-20 Keeper Belt Engine 11 532 40 00-08 Clutch Electric 12 532 40 50-97 Pulley Engine 15 532 41 41-51 T ank Fuel 18 532 42 06-35 Cap Asm 20 532 42 35-02 Control Throttle/Choke 21 532 41 63-58 Screw #10 x 0.750 BOS Thread 28 532 40 11-35 F ...

  • Husqvarna 96045001900 - page 38

    38 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 STEERING ASSEMBL Y 6 5 13 13 53 8 9 9 8 8 7 7 62 4 35 16 19 63 63 57 60 59 58 28 13 22 64 70 68 69 67 67 66 15 15 14 14 21 51 26 1 45 61 2 6 steering-tex_4-husq KEY P ART NO . NO. DESCRIPTION 1 532 42 34-69 Wheel, Steering 2 532 19 59-68 Axle Asm., F ront 4 532 40 30-87 Spindle ...

  • Husqvarna 96045001900 - page 39

    39 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 SEA T ASSEMBL Y 2 6 1 40 10 37 37 21 21 3 41 7 8 7 8 seat-tex_6.5SL_3 44 43 8 8 6 1 532 40 66-21 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins. 3/8-16 unc 7 532 12 41-81 Spring, Seat Cprsn 8 532 17 18-77 Bolt 5/16-18 ...

  • Husqvarna 96045001900 - page 40

    40 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 MOWER DECK 241 242 47 7 50 46 32 33 31 30 1 33 52 48 43 54 97 33 49 39 185 46 46 6 21 122 114 98 31 32 25 26 24 27 194 113 17 21 49 187 190 188 190 187 120 117 116 189 21 18 13 14 15 22 20 11 8 29 48_Deck_tex_22_r2 12 16 19 ...

  • Husqvarna 96045001900 - page 41

    41 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 MOWER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 40 35-82 Deck W eldment Mower 6 532 19 72-48 Cover Mandrel LH 7 532 19 91-02 Cover Mandrel RH 8 532 19 30-03 Bolt / W asher Asm. ...

  • Husqvarna 96045001900 - page 42

    42 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 91 lift-te x_3 91 89 87 89 87 2 532 19 52-23 Shaft Asm., Lift 3 532 19 52-31 Lever Asm., Lift 7 532 41 15-55 Grip, Lever 10 532 19 63-14 Spring T orsion 87 532 19 42-09 Pin Cotter 7/16 Bow Tie Lock 88 532 41 07-10 Spring Lift Assist 8 ...

  • Husqvarna 96045001900 - page 43

    43 TRACTOR - MODEL NO . YTH2348 (96045001900), PRODUCT NO. 960 45 00-19 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-vgt WHEELS AND TIRES KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 17 16 16 1 532 05 91-92 Cap, V alve, Tire 2 532 0 ...

  • Husqvarna 96045001900 - page 44

    44 SERVICE NOTES ...

  • Husqvarna 96045001900 - page 45

    45 SERVICE NOTES ...

  • Husqvarna 96045001900 - page 46

    46 SERVICE NOTES ...

  • Husqvarna 96045001900 - page 47

    47 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Husqvarna 96045001900 - page 48

    532 42 59-01 12.16.08 SR Printed in U.S.A. SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below: Lifetime Warranty (Parts a ...

Manufacturer Husqvarna Category Lawn Mower

Documents that we receive from a manufacturer of a Husqvarna 96045001900 can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- 96045001900 manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna 96045001900
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna 96045001900.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna 96045001900, service manual, brief instructions and user manuals Husqvarna 96045001900. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna 96045001900.

Similar manuals

A complete manual for the device Husqvarna 96045001900, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna 96045001900 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna 96045001900.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna 96045001900 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna 96045001900, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna 96045001900, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna 96045001900 - which should help us in our first steps of using Husqvarna 96045001900
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna 96045001900
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna 96045001900 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna 96045001900?

Use the form below

If you did not solve your problem by using a manual Husqvarna 96045001900, ask a question using the form below. If a user had a similar problem with Husqvarna 96045001900 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)