English dropdown-ico

Manual B&B Electronics TPC-1261H

106 pages 11.1 mb
Download

Go to site of 106

Summary
  • B&B Electronics TPC-1261H - page 1

    TPC-1261H GX3 LX800 T ouch Panel Computer with 12.1" SVGA TFT LCD User Manual ...

  • B&B Electronics TPC-1261H - page 2

    TPC-1261H User Manual ii Copyright The documentation and th e software included with this product are copy- righted 2004 by Advantech Co., Lt d. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time wi thout notice. No part of this man- ual may be reproduced, copied ...

  • B&B Electronics TPC-1261H - page 3

    iii Product W arranty (1 year ) Advantech warrants to you, the original purchaser , that each of its prod- ucts will be free from defects in ma terials and workman ship for one year from the date of purchase. This warranty does not apply t o any products which have b een repaired or altered by persons other than repair perso nnel authorized by Adva ...

  • B&B Electronics TPC-1261H - page 4

    TPC-1261H User Manual iv CE This product has passed the CE test for environmental specificati ons when shielded cables are used for external wiring. W e recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering inform ation. FCC Class A This equipment has been tested and f ...

  • B&B Electronics TPC-1261H - page 5

    v Packing List Before setting up the system, check that the items listed below are included and in g ood condition. If any item d oes not accord w ith the table, please contact y our dealer immediately . • 1 x TPC-1261H-A1 • 8 x Panel mounting clampers • 8 x Panel mounting screws • 1 x 3-Pin power connector • 1 x TPC x86 Series support CD ...

  • B&B Electronics TPC-1261H - page 6

    TPC-1261H User Manual vi 13. Never open the equi pment. For safety reasons, the equipment should be opened only by qualifi ed service personnel. 14. If one of the following si tuations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been ...

  • B&B Electronics TPC-1261H - page 7

    vii Table of Contents Contents Chapter 1 General Information ....................................... 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Specifications ............ ......................... .......................... ..... 3 1.2.1 Syst em Kernel .. ............ ........ ............ ...

  • B&B Electronics TPC-1261H - page 8

    TPC-1261H User Manual viii Figure 4.14:Update Dri ver - 1 ... ............. ........... ........... 25 Figure 4.15:Update Dri ver - 2 ... ............. ........... ........... 25 Figure 4.16:Update Dri ver - 3 ... ............. ........... ........... 26 Figure 4.17:Slave Bridge Instal lation Complete ........ .. 26 Figure 4.18:PCI-1602 Device Mana ...

  • B&B Electronics TPC-1261H - page 9

    ix Table of Contents C.2.2 IOCTL _WDT_DISABLE: ....... ........... ........... ......... .... 60 C.2.3 IOCTL_WDT_STROBE: ........... ......... ........... ......... .... 60 C.2.4 IOCTL_WDT_GETTIMEOUT : ........ ........... ........... .... 61 C.2.5 IOCTL_WDT_SETTIMEOU T: ........ ......... ........... ...... 61 C.2.6 IOCTL_WDT_REBOOT: . ........... ...

  • B&B Electronics TPC-1261H - page 10

    TPC-1261H User Manual x Figure F.2:Ins tall Wizard - 1 ...... ........... ........... ......... .. 84 Figure F.3:Ins tall Wizard - 2 ....... ........... ........... ......... .. 85 Figure F.4:Ins tall Wizard - 3 ....... ........... ........... ......... .. 85 F.2 Uninstall the Driver ......... ............................ .................... 86 Fi ...

  • B&B Electronics TPC-1261H - page 11

    2 CHAPTER 1 General Information This chapter gives b ackground infor- mation on TPC-1261H.. Sections include: • Introduction • Specifications • I/O Ports Arrangement • Panel Mounting • Exploded Diagrams • Dimensions & Cutout ...

  • B&B Electronics TPC-1261H - page 12

    TPC-1261H User Manual 2 Chapter 1 General Information 1.1 Introduction The TPC-1261H touch panel computer is a state-o f-the-art HMI (Human Machine Interface). This operator in terface with a 12.1” display is an x86-based platform with these key features: • Fanless By using a low-power processor , the system does not have to rely on fans, which ...

  • B&B Electronics TPC-1261H - page 13

    3 Chapter 1 1.2 Specifications 1.2.1 System Kernel • CPU: GeodeLink Cont rol Processor LX800 500MHz • BIOS: A ward 512KB flash memory • South Bridge: GeodeLink Control Processor CS5535 • VGA: GeodeLink C ontrol Processor LX800 50 0MHz • Ethernet: Realtek R TL8100BL; IEEE 802.3u protocol compatible • Wa t c h d o g T i m e r : W836 27 wa ...

  • B&B Electronics TPC-1261H - page 14

    TPC-1261H User Manual 4 Environment • Operating T emperature: 0 ~ 50° C (32 ~ 122° F) • S torage T emperature: -20 ~ 60° C (-4 ~ 140° F) • Humidity: 40° C @ 10~95% relative humidity (non-cond ensing) • V ibration: 1 grms (5~5 00Hz) 1.3 LCD Specifications • Display T ype: TFT color LCD • Size (diagonal): 12.1” • Maximum Resoluti ...

  • B&B Electronics TPC-1261H - page 15

    5 Chapter 1 1.5 Power • Input V oltage: 18 - 32V DC (th e fuse will become an open circuit if the input level exceeds 33 V DC ) • Ty p i c a l : 24V DC @2.5Amp 1.6 I/O Port s Arrangement The arrangement of the I/O ports is shown in Figure 1.1. Figure 1.1: I/O Port Arrangement 1.7 Panel Mounting 1. There is an adhesive waterproof gasket on the M ...

  • B&B Electronics TPC-1261H - page 16

    TPC-1261H User Manual 6 Figure 1.2: Panel Mounting 1.8 Dimensions and Cutout • W eight: 4.1 kg (without HDD) • Dimensions: 31 1 x 237 x 58 mm (W x H x D) • Cutout: 302 x 228 mm (suggest ed) ...

  • B&B Electronics TPC-1261H - page 17

    7 Chapter 1 Figure 1.3: Dimensions ...

  • B&B Electronics TPC-1261H - page 18

    TPC-1261H User Manual 8 ...

  • B&B Electronics TPC-1261H - page 19

    2 CHAPTER 2 System Setup This chapter provides a brief explana- tion for operating TPC-1261H. ...

  • B&B Electronics TPC-1261H - page 20

    TPC-1261H User Manual 10 Chapter 2 System Setup Y ou can easily get TPC-1261 H started by following the b elow steps. • Step 1: Unpack the TPC-1261H p ackage. Check the packing list at the beginning of th is manual to make sure all items have been included. Figure 2.1: Unpack the Package ...

  • B&B Electronics TPC-1261H - page 21

    11 Chapter 2 • Step 2: Install a CompactFlash card containi ng W indows CE, embed- ded W indow s XP or another operating system . Figure 2.2: Install CompactFlash Memory Card • Step 3: Connect the po wer connector to the 24 V DC power lines. The power lines can either be of some power adapter or in-house power source. Figure 2.3: Power Connecto ...

  • B&B Electronics TPC-1261H - page 22

    TPC-1261H User Manual 12 • Step 4: Plug th e power lines into the system power receptor . • Step 5: Push the power button to power on the system (figure 2.4). • Step 6: Calibrate the touchscreen (click "PM" i n the bottom corner). Figure 2.5: T ouchscreen Ic on Figure 2.6: T ouchscreen Calibration Note: We are using Window s XP as t ...

  • B&B Electronics TPC-1261H - page 23

    2 CHAPTER 3 System Engine ...

  • B&B Electronics TPC-1261H - page 24

    TPC-1261H User Manual 14 Chapter 3 System Engine T able 3.1: Mainboard Connectors & Jumper Settings Label Funct ion Description CN2 LCD POWER LCD INVERTER Connector CN3 CF Compa ctFlash socket CN4 IDE Internal IDE 44pin(2mm) connector CN5 ETHERNET RJ45 LAN PORT CN6 LPT Printer Port CN7 COM1 Seri al port:COM2 RS232 CN8 COM2 Seri al port:COM1 RS2 ...

  • B&B Electronics TPC-1261H - page 25

    15 Chapter 3 Figure 3.1: Main Board Connect ors - 1 Figure 3.2: Main Board Connect ors - 2 ...

  • B&B Electronics TPC-1261H - page 26

    TPC-1261H User Manual 16 ...

  • B&B Electronics TPC-1261H - page 27

    2 CHAPTER 4 Sof tware Configuration Sections include: • VGA Driv er Installat ion • Advantech COM Installation • Entertainment Encryp tion/ Decryption Driver Installation ...

  • B&B Electronics TPC-1261H - page 28

    TPC-1261H User Manual 18 Chapter 4 Sof tware Configuration A support CD-ROM for TPC-1261H is available an d along with the product. There are related utilities and drivers of TPC-1261H for W indows XP . Please insert the support CD-ROM into your CD-ROM driver and install th e VGA graphics driver , Advantech com driver, T ouchscreen driver and WDM d ...

  • B&B Electronics TPC-1261H - page 29

    19 Chapter 4 Figure 4.2: Update D river Step 3: Then follow the update wizard processures. Figure 4.3: Update Wizard-1 ...

  • B&B Electronics TPC-1261H - page 30

    TPC-1261H User Manual 20 Figure 4.4: Update W izard-2 Figure 4.5: Update Wizard-3 ...

  • B&B Electronics TPC-1261H - page 31

    21 Chapter 4 Figure 4.6: Update W izard-4 Figure 4.7: Update Wizard-5 ...

  • B&B Electronics TPC-1261H - page 32

    TPC-1261H User Manual 22 Figure 4.8: Update W izard-6 Step 4: After you successfully upda te the driver , you can see the VGA successfully installed from the device mana ger . Figure 4.9: Driver Installation Complete ...

  • B&B Electronics TPC-1261H - page 33

    23 Chapter 4 4.2 Advantech CO M Driver Inst all T wo com ports named COM3 and COM4 on TPC-1261H are Advantech Special com port. Please follow the steps below to install the d river . Step 1: Insert the CD-ROM into your CD-ROM drive. Go to the direc- tory: …TPC-1261HDriv erCom Port Driver and then excute PCI_ICOM.exe Figure 4.10: PCI_ICOM Setup ...

  • B&B Electronics TPC-1261H - page 34

    TPC-1261H User Manual 24 Figure 4.12: PCI ICOM Installation - 2 Step 3: Then, go to “Device Manager” to update the driver . Click “?PCI Serial Port” and then select “Driver” T ab to update driver as shown in Figure 4.9 Figure 4.13: Device Manager Screen ...

  • B&B Electronics TPC-1261H - page 35

    25 Chapter 4 Figure 4.14: Update Driver - 1 Step 4: Follow the hardw are upd ate wizard as the figures below . Figure 4.15: Update Driver - 2 ...

  • B&B Electronics TPC-1261H - page 36

    TPC-1261H User Manual 26 Figure 4.16: Update Driver - 3 Step 5: Complete the PCI-1602 Se ries Slave Bridge installation. Figure 4.17: Slave Bridge Installation Complete ...

  • B&B Electronics TPC-1261H - page 37

    27 Chapter 4 Step 6: Then, go to “Device Manager”. Y ou can find “Advantech PCI- 1602 Series Slave Br idge” is on the list. Figure 4.18: PCI-1602 Device Manager Step 7: And then c l ick “? PCI Seri al Port” to update the driver . ...

  • B&B Electronics TPC-1261H - page 38

    TPC-1261H User Manual 28 Figure 4.19: PCI Serial port Device Manager Figure 4.20: Update Driver - 1 ...

  • B&B Electronics TPC-1261H - page 39

    29 Chapter 4 Step 8: Follow the hardw are upd ate wizard as the figures below . Figure 4.21: Update Driver - 2 Figure 4.22: Update Driver - 3 ...

  • B&B Electronics TPC-1261H - page 40

    TPC-1261H User Manual 30 Step 9: Complete the Advantech PCI-1602 Series Master Bridge installa- tion. Figure 4.23: PCI-1602 Master Installation Step 10: Then, follow the wizard the install the software for Advantech PCI serial ports as the below . Figure 4.24: PCI Serial Port Installation - 1 ...

  • B&B Electronics TPC-1261H - page 41

    31 Chapter 4 Figure 4.25: PCI Serial Port Installation - 2 Figure 4.26: PCI Serial Port Installation - 3 ...

  • B&B Electronics TPC-1261H - page 42

    TPC-1261H User Manual 32 Figure 4.27: PCI Serial Port Installation - 4 Figure 4.28: PCI Serial Port Installation - 5 ...

  • B&B Electronics TPC-1261H - page 43

    33 Chapter 4 Figure 4.29: PCI Serial Port Installation - 6 Figure 4.30: PCI Serial Port Installation - 7 ...

  • B&B Electronics TPC-1261H - page 44

    TPC-1261H User Manual 34 Step 1 1: After the steps are done, the software for the com3 and com4 is successfully installed. Go to “D evice Manager” and find the list as below . Figure 4.31: Installation Complete 4.3 Entert ainment Encryption/Decryption Driver Step 1: Insert the CD-ROM and go to “Device Manager”. Click “Enter- tainment Encr ...

  • B&B Electronics TPC-1261H - page 45

    35 Chapter 4 Step 2: Following t he install shie ld wizard to finish the setup. Figure 4.33: Inst all W izard - 1 Figure 4.34: Install W izard - 2 ...

  • B&B Electronics TPC-1261H - page 46

    TPC-1261H User Manual 36 Figure 4.35: Install W izard - 3 Step 4: The driver is successfully installed. Y ou can check via “Device Manager” as the below . Figure 4.36: Driver Installation Complete ...

  • B&B Electronics TPC-1261H - page 47

    2 CHAPTER 5 F e a t u r e s i n Windows XP Embedded Sections include: • EWF • HORM • Advantech U tilities ...

  • B&B Electronics TPC-1261H - page 48

    TPC-1261H User Manual 38 Chapter 5 Features in Windows XP Embedded TPC-1261H supports the embedd ed W in dows platform. This section out- lines the importan t featur es (EWF and HORM), that are provided in W in- dows XP embedded. 5.1 EWF EWF stands for Enhanced W rite Filter . It provides an upper filter in the storage device driver stack that redi ...

  • B&B Electronics TPC-1261H - page 49

    39 Chapter 5 5.2 HORM HORM stands for Hibernate Once R esume Many . In HORM environ- ment, a single hi bernation file is used to boot th e system repeatedly . T o set a HORM environment, pleas e follow the steps below . Please make sure EWF is disabled. Y ou can run OSUnLock to disable EWF . Enable hibernation sup port: Run ‘power options’ in c ...

  • B&B Electronics TPC-1261H - page 50

    TPC-1261H User Manual 40 5.3.1 V ersion Informati on Start menu-> All Programs -> Advantech This states the current XPE runtime information in cluding hardware plat- form, version, bui ld number , release date, XPE QFEs installed in compo- nent database and XP Pro Patches you in stalled manually . 5.3.2 OSLock and OSUnLock The two utilities a ...

  • B&B Electronics TPC-1261H - page 51

    41 Chapter 5 ...

  • B&B Electronics TPC-1261H - page 52

    TPC-1261H User Manual 42 ...

  • B&B Electronics TPC-1261H - page 53

    2 APPENDIX A Serial Port Settings ...

  • B&B Electronics TPC-1261H - page 54

    TPC-1261H User Manual 44 Appendix A Serial Port Settings A.1 COM1/ COM2/ COM3 Connector Definition Pin Signal 1N D C D 2N R X 3N T X 4N D T R 5G N D 6N D S R 7N R T S 8N C T S 9N R I Note: COM1 and COM2 only suppor t half-duplex (Maximum baud rate: 1 15.2Kbps) 6 5 9 1 ...

  • B&B Electronics TPC-1261H - page 55

    45 Appendix A A.2 COM4 Setting The serial port COM4 on the TPC-1570H is adjustable. It can be set to RS-232, RS- 422 or RS -485. This po rt is designe d with auto data flow control capability. In other word , the TPC-1570H can automatically detect the data flow direction at this port when the two wired RS-485 communication is activated. COM4 Mode S ...

  • B&B Electronics TPC-1261H - page 56

    TPC-1261H User Manual 46 PIN RS-232 RS-422 RS-485 1 NDCD TX- D- 2N R X T X + D + 3N T X R X + 4 NDTR RX- 5 GND GND GND 6 NDSR 7N R T S 8N C T S 9N R I ...

  • B&B Electronics TPC-1261H - page 57

    2 APPENDIX B W atchdog T imer Programming ...

  • B&B Electronics TPC-1261H - page 58

    TPC-1261H User Manual 48 Appendix B W atchdog T imer Programming B.1 Overview The TPC-1261H watchdog tim er can be used to monitor system software operation and take correc tive action if the software fails to functio n after the programmed period. This section descri bes the operation of the watchdog timer, and how to program it. The watchdog time ...

  • B&B Electronics TPC-1261H - page 59

    49 Chapter B B.2 W atchdog Timer Programming The I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex) is the data port. Y ou must fi rst assign the address of register by writing addr ess value into address port 2E(hex), then write/read data to/from the assigned reg ister through data port 2F (hex). F ...

  • B&B Electronics TPC-1261H - page 60

    TPC-1261H User Manual 50 T able B.1: W atchdog Timer Registers Address of register (2E) Attribute Description Read/Write V alue (2F) and description 87 (hex) ----- Write this address to I/O address port 2E (hex) twice to unlock the W83627HF 07 (hex) write Write 08 (hex) to select register of watchdog timer . 30 (hex) write Write 01 (hex) to enable ...

  • B&B Electronics TPC-1261H - page 61

    51 Chapter B B.3 Example Programs 1. Enable watchdog timer and set 10 sec. as timeout interval ;-------- --------- -------- --------- ---------- --------- ------ Mov dx,2eh ; Unlock W83627HF Mov al,87h Out dx,al Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Mov al,07h ; Select registers of watchdog timer Out dx,al Inc ...

  • B&B Electronics TPC-1261H - page 62

    TPC-1261H User Manual 52 Out dx,al Inc dx Mov al,10 Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; lock W8 3627HF Mov al,0aah Out dx,al 2. Enable watchdog timer and se t 5 minutes as timeout interval ;-------- --------- -------- --------- ---------- --------- ------ Mov dx,2eh ; unlock W83627H Mov al,87h Out d ...

  • B&B Electronics TPC-1261H - page 63

    53 Chapter B Out dx,al Inc dx In al,dx Or al,08h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Set timeout interval as 5 minutes and start co unting Mov al,0f6h Out dx,al Inc dx Mov al,5 Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; lock W8 3627HF Mov al,0aah Out dx,al ...

  • B&B Electronics TPC-1261H - page 64

    TPC-1261H User Manual 54 Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable watchdog timer to be reset by mouse Mov al,0f7h Out dx,al Inc dx In al,dx Or al,80h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; lock W8 3627HF Mov al,0 ...

  • B&B Electronics TPC-1261H - page 65

    55 Chapter B Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f7h Out dx,al Inc dx In al,dx Or al,40h Out dx,al ;-------- --------- -------- --------- ---------- --- ...

  • B&B Electronics TPC-1261H - page 66

    TPC-1261H User Manual 56 ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;Write 1 to bit 5 of F7 register Inc ...

  • B&B Electronics TPC-1261H - page 67

    2 APPENDIX C W atchdog T imer Programming on WinCE ...

  • B&B Electronics TPC-1261H - page 68

    TPC-1261H User Manual 58 Appendix C W atchdog T imer Program- ming on WinCE There is a built-in watchdog timer in Windows CE 4.2 for TPC-1261H. Y ou can access it through the WIN32 API. TPC-1261H provides a WDT driver to allow users to enable/disable the watc hdog timer . The driver name is “WDT1:”. Programmers must open th is driver before usi ...

  • B&B Electronics TPC-1261H - page 69

    59 Appendix C C.1.1 Parameters • hDevice [in] Handle to the device that is to perform the operation. Call the Cre- ateFile function to obt ain a device handle. • dwIoControlC ode [in] Specifies the contro l code for the operation. This value identifies the specific operation to be performed and the type of device on which the operation is to be ...

  • B&B Electronics TPC-1261H - page 70

    TPC-1261H User Manual 60 C.2 How to Use the Control Code There are 6 control codes for the op eration codes in the WDT driver . C.2.1 IOCTL _WDT_ENABLE: Enables the watchdog timer of your appl ication. By default, if the watch- dog timer is enabled, the WDT driver will automat ically trigger itself after the specified period and your application do ...

  • B&B Electronics TPC-1261H - page 71

    61 Appendix C C.2.4 IOCTL_WDT_GETTIMEOUT : Gets the W atchdo g time setting. lpInBuffer: unused. nInBufferSize: unused. lpOutBuffer: The DWORD po ints to your wa tchdog time setting . The W atchdog time setting is just a number . 0 means 2 second s, 1 means 5 seconds, 2 means 10 seconds, 3 means 15 seconds, 4 means 30 seconds, 5 means 45 seconds an ...

  • B&B Electronics TPC-1261H - page 72

    TPC-1261H User Manual 62 C.3 Examples #define WDT_CODE(ID) CTL_CODE(FILE_DEVICE_UNKNOWN,ID , METHOD_BUFFERED, FILE_ANY_ACCESS) #define IOCTL_WDT_ENABLE WDT_CODE (0x900) #define IOCTL_WDT_DI SABLE WDT_CODE(0 x901) #define IOCTL_WDT_ST ROBE WDT_CODE(0x902) #define IOCTL_WDT_GET_ TI MEOUT WDT_CODE(0x903) #define IOCTL_WDT_SET_TI MEOUT WDT_CODE(0x904) ...

  • B&B Electronics TPC-1261H - page 73

    63 Appendix C // Set the W atchdog T i mer as 10 seconds. Num ber 2 means 10 seconds. DeviceIoControl(m_hWDT , IOCTL_WDT_SET_TIMEOUT , &nIndex, sizeof(nIndex), NULL, 0, &dwT emp, NULL); // Enable the W atch dog timer DeviceIoControl(m_hWDT , IOCTL_WDT_ENABLE, NULL, 0, NULL, 0, &dwT emp, NULL); While (1) { // do your job here. Sleep(8000 ...

  • B&B Electronics TPC-1261H - page 74

    TPC-1261H User Manual 64 ...

  • B&B Electronics TPC-1261H - page 75

    2 APPENDIX D Accessory Kit Assembly Procedure This appendix shows how to connect to a CD-ROM via the CompactFlash slot.: ...

  • B&B Electronics TPC-1261H - page 76

    TPC-1261H User Manual 66 Appendix D Accessory Kit Assembly Procedure D.1 Comp actFlash to IDE T ransfer Kit Please follow this assembly procedur e to us e the CompactFlash slot to connect with a CD-ROM drive. 1. Connect the IDE cable to the adapter board. Figure D.1: Adapter Board and IDE Cable Figure D.2: Connecting the Adapter Board ...

  • B&B Electronics TPC-1261H - page 77

    67 Appendix D 2. Insert the adapter board into the Co mpactFlash slot. Figure D.3: CompactFlash Slot Figure D.4: Insert the Adapter Board into the CF slot Figure D.5: Inserted Adapter Board Note P in 1 is mar ked red ...

  • B&B Electronics TPC-1261H - page 78

    TPC-1261H User Manual 68 Connect the CD-ROM to the adapter board via the IDE cable and then connect the exte rnal power line to the CD-ROM. Figure D.6: Connect the CD-ROM via the IDE Cable Figure D.7: Plugging in the CD-ROM Drive ...

  • B&B Electronics TPC-1261H - page 79

    2 APPENDIX E HDD Kit Assembly ...

  • B&B Electronics TPC-1261H - page 80

    TPC-1261H User Manual 70 Appendix E HDD Kit Assembly TPC-1261H provides two way to assem ble the HDD into the system. The ruggized HDD kit is to resist against the high vib ration. E.1 Ruggedized HDD Kit Please follow the assembly procedure to install the HDD into the system. 1. Remove the default H DD cover from the system. The required parts are ...

  • B&B Electronics TPC-1261H - page 81

    71 Appendix E Figure E.2: Required Parts ...

  • B&B Electronics TPC-1261H - page 82

    TPC-1261H User Manual 72 2. Place the base bracket on the r ear case and carefully pull out the FPC cable through the hole of the b racket . Figure E.3: Opening the T op 3. Fasten the base on the rear case of the system by 5 screws. Figure E.4: Fast ening the brack et ...

  • B&B Electronics TPC-1261H - page 83

    73 Appendix E 4. Carefully connect the FPC cable to the HDD and then put the HDD insultor on the HDD. Figure E.5: Connectting the FPC with the HDD Figure E.6: Placing the HDD insulator on the HDD ...

  • B&B Electronics TPC-1261H - page 84

    TPC-1261H User Manual 74 5. Fasten the HDD holder with the HDD and HDD insulator . Please turn over the HDD holder and fasten them with 4 screws. Figure E.7: Reverse si de of the HDD holder Figure E.8: Fastening the HDD holder ...

  • B&B Electronics TPC-1261H - page 85

    75 Appendix E 6. Mount the H DD cushions with the HDD holder . Figure E.9: Mounting the cushions - 1 Figure E.10: Mounting the cushions - 2 ...

  • B&B Electronics TPC-1261H - page 86

    TPC-1261H User Manual 76 7. Place the HDD holder on the rear cover of the system and then fas- ten the holder with the system by four screws. Then, the assembl y of high vibration resistance HDD module is done. Figure E.1 1: Placing the HDD holder - 1 Figure E.12: Placing th e HDD holder - 2 ...

  • B&B Electronics TPC-1261H - page 87

    77 Appendix E Figure E.13: Fasten ing the HDD holder E.2 Internal HDD Kit Assembly Please follow the steps to assemble the internal HDD kit. 1. Remove the default HDD cover from the system. Figure E.14: Removing the HDD cover ...

  • B&B Electronics TPC-1261H - page 88

    TPC-1261H User Manual 78 2. There are four rubber screw casings, and four screws . Places the screws into their casings Figure E.15: Placing a sc rew into its rubber casing 3. Mount the rubber HDD cushions on the HDD cover . Figure E.16: Mounting the rubber casings ...

  • B&B Electronics TPC-1261H - page 89

    79 Appendix E 4. Connect the FPC cable to the HDD Figure E.17: Connecting the FPC cable 5. Put the HDD into the hole of the rear case. Figure E.18: Inserting the H DD ...

  • B&B Electronics TPC-1261H - page 90

    TPC-1261H User Manual 80 6. Lay the HDD i nsulator in right directio n. Figure E.19: Laying in the HDD insulator 7. Place the default HDD cover on the system. Figure E.20: Placing the cover back into position ...

  • B&B Electronics TPC-1261H - page 91

    81 Appendix E 8. Fasten the default HDD cover with the system. Figure E.21: Re-fastening the cover - 1 Figure E.22: Re-fastening the cover - 2 ...

  • B&B Electronics TPC-1261H - page 92

    TPC-1261H User Manual 82 9. Place the bracket of PCI/104 on the slot and fasten it into place. Figure E.23: Fastening the PCI/104 bracket - 1 Figure E.24: Fastening the PCI/104 bracket - 2 ...

  • B&B Electronics TPC-1261H - page 93

    2 APPENDIX F T ouchscreen Inst allation & Configuration This appendix demo nstrates how to install the PenMount touchscreen and set the configuration on TPC-1261H. This section uses Windows XP as an example. ...

  • B&B Electronics TPC-1261H - page 94

    TPC-1261H User Manual 84 Appendix F T ouchscreen Inst allation & Configuration F .1 Driver Inst allation Please insert the x86 TPC series suppor t CD and go to the driver folder: (TPC-1261HDriverUSB touch screen). Click setup.exe Figure F .1: Se tup.exe The screen displays the installat ion wizard for the PenMount USB soft- ware. Click “Nex ...

  • B&B Electronics TPC-1261H - page 95

    85 Appendix F Figure F .3: Install Wizard - 2 Figure F .4: Install Wizard - 3 ...

  • B&B Electronics TPC-1261H - page 96

    TPC-1261H User Manual 86 F .2 Uninst all the Driver Please go to Settings and then select Control Panel. Please click Add/ Remove Progr ams. Figure F .5: Uninstall -1 Select PenMount USB. Click Remo ve button. Then, select “Y es” to remove the PenMountUSB driver and reboot the system .. Figure F .6: Uninstall -2 ...

  • B&B Electronics TPC-1261H - page 97

    87 Appendix F F .3 T ouchscreen Calibration The “PM”, the i con of the PenMount Control Panel, is in the menu b ar after the touchscreen installation. Pl ease click the icon “PM” to call Pen- Mount Control Panel. It contains six fun ctions: Calibrate, Draw , Option, and About. About shows the driver version. Calibr ate T wo ways to calibrat ...

  • B&B Electronics TPC-1261H - page 98

    TPC-1261H User Manual 88 Figure F .8: S tandard Calibration -2 Figure F .9: S tandard Calibration -3 ...

  • B&B Electronics TPC-1261H - page 99

    89 Appendix F Advanced Calibration is for the aged tou chscreens by using 4, 9, 16 or 25 points to calibrate touch panel. Figure F .10: Advanced C alibration -1 Note T ouch the red sq uares in sequence. The cali- bration is completed af ter the fift h touch red point is calibrated. Press “ ESC” to skip. ...

  • B&B Electronics TPC-1261H - page 100

    TPC-1261H User Manual 90 Figure F .1 1: Advanced Calibration -2 Figure F .12: Plot Calib ration Data ...

  • B&B Electronics TPC-1261H - page 101

    91 Appendix F Draw This is to test the touchscreen operation. Its display show s touch loca- tion. Figure F .13: Draw Click “menu” and then click “clear screen” to clear the drawing. Note Plot Calibration Dat a enabled provides the blue lines to show linearity before calibration and black lines to show lin earity af ter calibration when you ...

  • B&B Electronics TPC-1261H - page 102

    TPC-1261H User Manual 92 Figure F .14: Clear Screen Option This option is t o set the operatio n mode and b eep sounds if t he beep sound is enabled. The operation mode, stream mode and point mode, is to enable/ disable the mouse’ s ability to drag on-screen icons. Stream mode let the mouse functions as normal and dragging on-screen. Point mode i ...

  • B&B Electronics TPC-1261H - page 103

    93 Appendix F Figure F .15: Option ...

  • B&B Electronics TPC-1261H - page 104

    TPC-1261H User Manual 94 ...

  • B&B Electronics TPC-1261H - page 105

    2 APPENDIX G Fuse S p ecifications ...

  • B&B Electronics TPC-1261H - page 106

    TPC-1261H User Manual 96 Appendix G Fuse S p ecifications G .1 Fuse Specifications Rating : 250 V AC, 5 A Size: 5 x 20 mm G .2 Fuse Replacement Step 1: Remove the fuse cover Step 2: Replace the damaged fuse with a new one Step 3: Place the fuse co ver back into position. Figure G .1: Fuse Replacement Note For your protection, the fuse is set to bre ...

Manufacturer B&B Electronics Category Computer Monitor

Documents that we receive from a manufacturer of a B&B Electronics TPC-1261H can be divided into several groups. They are, among others:
- B&B Electronics technical drawings
- TPC-1261H manuals
- B&B Electronics product data sheets
- information booklets
- or energy labels B&B Electronics TPC-1261H
All of them are important, but the most important information from the point of view of use of the device are in the user manual B&B Electronics TPC-1261H.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals B&B Electronics TPC-1261H, service manual, brief instructions and user manuals B&B Electronics TPC-1261H. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product B&B Electronics TPC-1261H.

Similar manuals

A complete manual for the device B&B Electronics TPC-1261H, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use B&B Electronics TPC-1261H by users. Manuals are usually written by a technical writer, but in a language understandable to all users of B&B Electronics TPC-1261H.

A complete B&B Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual B&B Electronics TPC-1261H - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the B&B Electronics TPC-1261H, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the B&B Electronics TPC-1261H, that we can find in the current document
3. Tips how to use the basic functions of the device B&B Electronics TPC-1261H - which should help us in our first steps of using B&B Electronics TPC-1261H
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with B&B Electronics TPC-1261H
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of B&B Electronics TPC-1261H in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning B&B Electronics TPC-1261H?

Use the form below

If you did not solve your problem by using a manual B&B Electronics TPC-1261H, ask a question using the form below. If a user had a similar problem with B&B Electronics TPC-1261H it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)