English dropdown-ico

Manual Sun Microsystems CP3220

135 pages 4.5 mb
Download

Go to site of 135

Summary
  • Sun Microsystems CP3220 - page 1

    Sun Microsystems, Inc. www .sun.com Submit comments about this document at: http://www.sun.com/hwdocs/feedback Sun Netra ™ CP3220 Blade Ser v er User’ s Guide P ar t No . 820-1982-12 January 2010, Revision 01 ...

  • Sun Microsystems CP3220 - page 2

    Please Recycle Copyright © 2010 Sun Microsystems, Inc., 4150 Network Cir cle, Santa Clara, California 95054, U.S.A. All rights reserved. This distribution may include materials developed by third parties. Parts of the product may be derived fr om Berkeley BSD systems, licensed from the University of California. UNIX is a r egistered trademark in t ...

  • Sun Microsystems CP3220 - page 3

    iii Contents Preface xv 1. Introduction 1–1 1.1 Overview 1–2 1.2 Features 1–2 1.3 Physical Description 1–3 1.3.1 Front Panel Components 1–3 1.3.2 Blade Server Diagram 1–6 1.4 System Configurations 1–7 1.4.1 AMC Modules 1–7 1.4.2 Advanced Rear T ransition Module 1–8 1.5 Hot-Swap Support 1–12 1.6 System Components 1–12 1.6.1 Req ...

  • Sun Microsystems CP3220 - page 4

    iv Sun Netra CP3220 Blade Server User’s Guide • January 2010 2. Hardware Installation and Service 2–1 2.1 Safety and T ool Requirements 2–2 2.1.1 Equipment and Operator Safety 2–2 2.1.2 Materials and T ools Required 2–3 2.2 Installing the Blade Server 2–3 2.2.1 Preparing for the Installation 2–3 2.2.1.1 Check Power , Thermal, Enviro ...

  • Sun Microsystems CP3220 - page 5

    Contents v 2.3.4 Powering On the System 2–18 2.3.5 Automatic Power-Of f Events 2–18 2.3.6 Servicing DIMMs 2–19 2.3.6.1 DIMM Requirements 2–19 2.3.6.2 Installing a DDR2 DIMM 2–21 2.3.6.3 Removing a DDR2 DIMM 2–22 2.3.7 Installing the Optional Compact Flash Card 2–24 2.3.8 Installing Optional AMC Cards 2–26 2.3.9 Adding or Replacing a ...

  • Sun Microsystems CP3220 - page 6

    vi Sun Netra CP3220 Blade Server User’s Guide • January 2010 4. Conf iguring and Using BIOS Firmware 4–1 4.1 About BIOS Settings 4–2 4.1.1 Navigating BIOS Screens 4–2 4.1.2 BIOS Considerations 4–2 4.1.2.1 BIOS Option ROMs on the Sun Netra CP3220 Blade Server 4–2 4.1.2.2 AMD PowerNow! Feature Enabled by Default 4–3 4.1.3 Description ...

  • Sun Microsystems CP3220 - page 7

    Contents vii 5.4.5 Broadcom 5715C Gigabit Ethernet 5–6 5.4.6 Sun Dual 10-Gbit Ethernet/Quad 1-Gbit RGMII Network Interface Chip (Sun 10 GbE Multithreaded Networking ASIC) 5–7 5.5 I/O Components 5–7 5.5.1 AMC Slots 5–7 5.5.2 EIDE/A T A for Compact Flash 5–8 5.5.3 SAS/SA T A 5–8 A. Physical Characteristics A–1 A.1 Form Factor A–2 A.2 ...

  • Sun Microsystems CP3220 - page 8

    viii Sun Netra CP3220 Blade Server User’s Guide • January 2010 ...

  • Sun Microsystems CP3220 - page 9

    ix Figur es FIGURE 1-1 Sun Netra CP3220 Dual-Core Blade Server (Front View) 1–4 FIGURE 1-2 Sun Netra CP3220 Quad-Core Blade Server (Front View) 1–5 FIGURE 1-3 Sun Netra CP3220 Blade Server (Component Side View) 1–6 FIGURE 1-4 Sun Netra CP3220 Blade Server in Shelf Enclosure 1–7 FIGURE 1-5 Sun Netra CP32x0 SAS Storage Advanced Rear Transitio ...

  • Sun Microsystems CP3220 - page 10

    x Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 4-1 BIOS Main Menu 4–6 FIGURE 4-2 Boot Settings Menu 4–7 FIGURE 4-3 Boot Device Priority Menu 4–8 FIGURE 4-4 Security Settings Menu 4–10 FIGURE 4-5 Change Password Menu 4–10 FIGURE 5-1 Block Diagram 5–2 FIGURE 5-2 AMD Opteron Processors Block Diagram 5–4 FIGURE A-1 ...

  • Sun Microsystems CP3220 - page 11

    Figures xi FIGURE B-18 Boot Device Priority Menu B–11 FIGURE B-19 Boot Hard Disk Drive Priority Menu B–11 FIGURE B-20 Security Settings Menu B–12 FIGURE B-21 Change Password Settings Menu B–12 FIGURE B-22 Chipset Main Menu B–13 FIGURE B-23 NorthBridge Chipset Configuration Menu B–13 FIGURE B-24 NorthBridge Chipset Memory Configuration M ...

  • Sun Microsystems CP3220 - page 12

    xii Sun Netra CP3220 Blade Server User’s Guide • January 2010 ...

  • Sun Microsystems CP3220 - page 13

    xiii T ables TABLE 1-1 I/O Configurations 1–11 TABLE 2-1 Local Area Network Information 2–5 TABLE 2-2 Netinstall Boot Device Table 2–15 TABLE 2-3 Extra MAC Addresses for Virtual LAN Configuration 2–16 TABLE 2-4 Pin Functions on Jumper 1 2–30 TABLE 4-1 BIOS Setup Screens Summary 4–3 TABLE 4-2 POST Options 4–15 TABLE A-1 Airflow Require ...

  • Sun Microsystems CP3220 - page 14

    xiv Sun Netra CP3220 Blade Server User’s Guide • January 2010 ...

  • Sun Microsystems CP3220 - page 15

    xv Pr eface The Sun Netra CP3220 Blade Server User ’ s Guide describes the hardware specif ications, function, and physical properties of the Sun Netra™ CP3220 blade server . It also provides detailed information on the system firmwar e. The Sun Netra CP3220 Blade Server User ’ s Guide is written for system integration engineers, field applic ...

  • Sun Microsystems CP3220 - page 16

    xvi Sun Netra CP3220 Blade Server User’s Guide • January 2010 Using UNIX Commands This document might not contain information about basic UNIX ® commands and procedur es such as shutting down the system, booting the system, and configuring devices. Refer to the following for this information: ■ Software documentation that you received with y ...

  • Sun Microsystems CP3220 - page 17

    Preface xvii T ypographic Conventions Related Documentation The following table lists the documentation for this product. Except for the Important Safety Information for Sun Hardware Systems , all the documents listed are available online at: http://docs.sun.com/app/docs/prod/cp3220.brd#hic T ypeface * * The settings on your browser might differ fr ...

  • Sun Microsystems CP3220 - page 18

    xviii Sun Netra CP3220 Blade Server User’s Guide • January 2010 Documentation, Support, and T raining Thir d-Party W eb Sites Sun is not responsible for the availability of third-party web sites mentioned in this document. Sun does not endorse and is not responsible or liable for any content, advertising, products, or other materials that are a ...

  • Sun Microsystems CP3220 - page 19

    1-1 CHAPTER 1 Intr oduction This chapter provides an overview of the features, conf igurations, and system requir ements of the Sun Netra CP3220 blade server . This chapter contains the following topics: ■ Section 1.1, “Overview” on page 1-2 ■ Section 1.2, “Features” on page 1-2 ■ Section 1.3, “Physical Description” on page 1-3 ? ...

  • Sun Microsystems CP3220 - page 20

    1-2 Sun Netra CP3220 Blade Server User’s Guide • January 2010 1.1 Overview The Sun Netra CP3220 blade server is a high-performance, single-board computer based on an AMD Opteron X64 pr ocessor . The blade server is designed for high availability in a switched network computing environment. This blade server is compliant with Advanced T elecommu ...

  • Sun Microsystems CP3220 - page 21

    Chapter 1 Introduction 1-3 ■ E-IDE master to support one Compact Flash socket supporting up to 16-Gbyte user flash (accessible when blade is r emoved from chassis) ■ Management support using on-board IPM contr oller (Renesas H8) that provides a dual IPMB bus and IPMI redundant channels ■ Rear I/O expansion provided to an optional R TM, compat ...

  • Sun Microsystems CP3220 - page 22

    1-4 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 1-1 Sun Netra CP3220 Dual-Cor e Blade Server (Front V iew) Figure Legend 1 Locking screws 6 Reset button 2 Latches 7 10/100/1000 Ethernet management port 3 Out-of-service (OOS) LED 8 Serial port 4 OK LED 9 USB ports 5 AMC card slots RES ET ...

  • Sun Microsystems CP3220 - page 23

    Chapter 1 Introduction 1-5 FIGURE 1-2 Sun Netra CP3220 Quad-Cor e Blade Server (Front V iew) Figure Legend 1 Locking screws 6 Reset button 2 Latches 7 10/100/1000 Ethernet management port 3 Out-of-service (OOS) LED 8 Serial port 4 OK LED 9 USB ports 5 AMC card slots ...

  • Sun Microsystems CP3220 - page 24

    1-6 Sun Netra CP3220 Blade Server User’s Guide • January 2010 1.3.2 Blade Server Diagram FIGURE 1-3 Sun Netra CP3220 Blade Server (Component Side V iew) Figure Legend 1 Compact Flash card 4 Zone 1 power connector 2 Zone 3 connectors 5 CPU Heatsink 3 Zone 2 connectors 6 DIMMs ...

  • Sun Microsystems CP3220 - page 25

    Chapter 1 Introduction 1-7 1.4 System Conf igurations Sun Netra CP3220 blade servers can be installed into an A TCA shelf (chassis), as shown in FIGURE 1-4 . The blade servers can be deployed in various electrical configurations to suit user r equirements. For example, the blade server can be configur ed to boot from a network as a diskless client ...

  • Sun Microsystems CP3220 - page 26

    1-8 Sun Netra CP3220 Blade Server User’s Guide • January 2010 1.4.2 Advanced Rear T ransition Module Y ou can install an optional Sun Netra CP32x0 Advanced Rear T ransition Module (AR TM) ( FIGURE 1-5 ) into the rear of the A TCA shelf, opposite the Sun Netra CP3220 blade server ( FIGURE 1-6 ). The Sun Netra CP32x0 SAS Storage Advanced Rear T r ...

  • Sun Microsystems CP3220 - page 27

    Chapter 1 Introduction 1-9 Note – Use only serial cables that are less than 10 meters in length. FIGURE 1-6 shows the physical relationship between the Sun Netra CP3220 blade server , the AR TM, and the backplane in a typical A TCA system. Figure Legend 1 Serial port 2 10/100/1000 MBASE-T management port 3 External SAS port (secondary) 4 External ...

  • Sun Microsystems CP3220 - page 28

    1-10 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 1-6 Sun Netra CP3220 Blade Server , Backplane, and Relationship to AR TM Note – When using the Sun Netra CP32x0 AR TM with the Sun Netra CP3220 blade server , use shielded cables of less than 10 meters in length for serial I/O ports. Caution – Y ou must use shielded cable ...

  • Sun Microsystems CP3220 - page 29

    Chapter 1 Introduction 1-11 10/100/1000BASE-T per second Ethernet RJ-45 port from the host to the rear of the system. This port can be used to accomplish, optionally , a network boot as a diskless client. The other configurations requir e IHV hardware. T ABLE 1-1 I/O Conf igurations I/O Hard ware Required Description Ethernet Sun Netra CP32x0 AR TM ...

  • Sun Microsystems CP3220 - page 30

    1-12 Sun Netra CP3220 Blade Server User’s Guide • January 2010 1.5 Hot-Swap Support In general, the hot-swap process includes the orderly connection of the har dware and software. The pr ocess uses hardwar e connection control to connect the hardware in an orderly sequence. The pr ocess includes the use of pins of differ ent lengths to accompli ...

  • Sun Microsystems CP3220 - page 31

    Chapter 1 Introduction 1-13 Caution – Y ou can damage the Sun Netra CP3220 blade server components if you install the blade server in a chassis that does not provide suff icient cooling. For more information, see Section 2.2.1.1, “Check Power , Thermal, Environmental, and Space Requirements” on page 2-4 . Note – Use only shielded serial cab ...

  • Sun Microsystems CP3220 - page 32

    1-14 Sun Netra CP3220 Blade Server User’s Guide • January 2010 1.7 T echnical Support and W arranty Should you have any technical questions or support issues that are not addressed in the Sun Netra CP3220 blade server documentation set or on the technical support web site, contact your local Sun Services repr esentative. This hardwar e carries ...

  • Sun Microsystems CP3220 - page 33

    Chapter 1 Introduction 1-15 FIGURE 1-7 Sun Netra CP3220 Blade Server Bar code Labeling P ar t number label Ser ial number label ...

  • Sun Microsystems CP3220 - page 34

    1-16 Sun Netra CP3220 Blade Server User’s Guide • January 2010 ...

  • Sun Microsystems CP3220 - page 35

    2-1 CHAPTER 2 Har dware Installation and Service This chapter describes the Sun Netra CP3220 blade server hardwar e installation and service procedur es. This chapter contains the following topics: ■ Section 2.1, “Safety and T ool Requirements” on page 2-2 ■ Section 2.2, “Installing the Blade Server” on page 2-3 ■ Section 2.3, “Serv ...

  • Sun Microsystems CP3220 - page 36

    2-2 Sun Netra CP3220 Blade Server User’s Guide • January 2010 2.1 Safety and T ool Requir ements 2.1.1 Equipment and Operator Safety Refer to the Important Safety Information for Sun Hardware Systems (816-7190) for general safety information. Read the following safety statements that are specific to the Sun Netra CP3220 blade server carefully b ...

  • Sun Microsystems CP3220 - page 37

    Chapter 2 Hardware Installation and Ser vice 2-3 The grounded mat or the chassis must be connected to a facility ground to prevent a f loating ground. ■ Keep blade servers in the antistatic bags until they are needed. ■ Remove a blade server from its antistatic bag only when wearing a properly connected ground strap. ■ Place blade servers tha ...

  • Sun Microsystems CP3220 - page 38

    2-4 Sun Netra CP3220 Blade Server User’s Guide • January 2010 4. V erify that local area network (LAN) preparations are completed (see Section 2.2.1.2, “Local Network IP Addresses and Host Names W orksheet” on page 2-5 ). 5. Ensure that the host names and their network IP addresses ar e allocated and register ed at the site. Record this inf ...

  • Sun Microsystems CP3220 - page 39

    Chapter 2 Hardware Installation and Ser vice 2-5 2.2.1.2 Local Network IP Addresses and Host Names W orksheet Collect the information listed in T ABLE 2-1 to connect hosts to the LAN. Ask your network administrator for help, if necessary . This information is not needed for a stand-alone installation. Y ou may need the MAC (Ethernet) addresses of t ...

  • Sun Microsystems CP3220 - page 40

    2-6 Sun Netra CP3220 Blade Server User’s Guide • January 2010 2.2.1.3 Installation Procedur e Summary This section summarizes the high-level procedures that ar e required to install the Sun Netra CP3220 blade server . Ensur e that you are familiar with the information in Section 2.2.2, “Configuring the Hardware” on page 2-6 through the end ...

  • Sun Microsystems CP3220 - page 41

    Chapter 2 Hardware Installation and Ser vice 2-7 2.2.2.1 V erify Chassis Fan T ray Upgrade Caution – The Sun Netra CT 900 server fan tray upgrade kit (594-4953) must be installed in the chassis before the Sun Netra CP3220 blade server is installed. This fan tray upgrade is requir ed to provide adequate cooling and pr event the system from over he ...

  • Sun Microsystems CP3220 - page 42

    2-8 Sun Netra CP3220 Blade Server User’s Guide • January 2010 2.2.2.3 Configuring the Advanced Rear T ransition Module Hardwar e If you are using a Sun Netra CP32x0 Advanced Rear T ransition Module (ARTM), refer to the appr opriate documentation. See Section , “Related Documentation” on page -xvii . Y ou can also see Section A.3, “Connect ...

  • Sun Microsystems CP3220 - page 43

    Chapter 2 Hardware Installation and Ser vice 2-9 FIGURE 2-1 Installing the Sun Netra CP32x0 AR TM ...

  • Sun Microsystems CP3220 - page 44

    2-10 Sun Netra CP3220 Blade Server User’s Guide • January 2010 ▼ T o Install an AR TM 1. V erify that you have taken the necessary antistatic precautions. See Section 2.1.1, “Equipment and Operator Safety” on page 2-2 . 2. From the rear of the system, choose an appropriate slot for the AR TM. The AR TM must be installed, inline, behind a ...

  • Sun Microsystems CP3220 - page 45

    Chapter 2 Hardware Installation and Ser vice 2-11 FIGURE 2-2 Injector/Ejector Latch and Locking Scr ew on the ARTM 6. Carefully align the edges of the AR TM with the card guides in the appropriate slot. Look into the enclosure to verify corr ect alignment of the rails in the guides. 7. Keep the AR TM aligned in the guides, and slide the AR TM in un ...

  • Sun Microsystems CP3220 - page 46

    2-12 Sun Netra CP3220 Blade Server User’s Guide • January 2010 10. Install the Sun Netra CP3220 blade server into the front of the A TCA shelf in the corresponding slot. See Section 2.2.3.2, “Installing the Blade Server Into the Shelf” on page 2-12 for instructions. 2.2.3.2 Installing the Blade Server Into the Shelf Note – Y ou can instal ...

  • Sun Microsystems CP3220 - page 47

    Chapter 2 Hardware Installation and Ser vice 2-13 2.2.4 Connecting External I/O Cables Front panel ports ar e typically used for maintenance and troubleshooting purposes in installed and running systems. External I/O cables are connected to the Sun Netra CP3220 blade server or to the Sun Netra CP32x0 ARTM. T o connect each of these following cables ...

  • Sun Microsystems CP3220 - page 48

    2-14 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 2-3 Serial Port on the Sun Netra CP3220 Blade Server 3. Use one of the following to establish a full-duplex serial terminal connection with the Sun Netra CP3220 blade server: ■ The tip utility ■ The minicom utility Serial por t RES ET ...

  • Sun Microsystems CP3220 - page 49

    Chapter 2 Hardware Installation and Ser vice 2-15 ■ A telnet utility (Connect to the proper port on a Network T erminal Server to which the Sun Netra CP3220 is connected.) ■ Another suitable serial communications program on the system console For example, if you are using a UNIX system as the system console, at the UNIX prompt in a command tool ...

  • Sun Microsystems CP3220 - page 50

    2-16 Sun Netra CP3220 Blade Server User’s Guide • January 2010 The Sun Netra CP3220 blade server supports virtual LAN configuration for the Sun 10 GbE Multithreaded Networking ASIC ports (MAC addresses 4, 5, 6, and 7). When configur ed, the virtual LAN feature enables the assignment of multiple MAC address to one port. T ABLE 2-3 lists the extr ...

  • Sun Microsystems CP3220 - page 51

    Chapter 2 Hardware Installation and Ser vice 2-17 2.3 Service Pr ocedures 2.3.1 Hot-Swapping the Sun Netra CP3220 Blade Server Y ou can remove the Sun Netra CP3220 blade server without powering of f the entire chassis by performing these steps. 1. Power off the blade server . See Section 2.3.2, “Powering Off the Sun Netra CP3220 Blade Server” o ...

  • Sun Microsystems CP3220 - page 52

    2-18 Sun Netra CP3220 Blade Server User’s Guide • January 2010 2.3.3 Removing the Sun Netra CP3220 Blade Server 1. Power off the Sun Netra CP3220 blade server . Use the instructions in Section 2.3.2, “Powering Off the Sun Netra CP3220 Blade Server” on page 2-17 . 2. If installed, remove all cables from the front of the Sun Netra CP3220 blad ...

  • Sun Microsystems CP3220 - page 53

    Chapter 2 Hardware Installation and Ser vice 2-19 2.3.6 Servicing DIMMs 2.3.6.1 DIMM Requirements The Sun Netra CP3220 blade server supports a total of eight DIMMs and the maximum memory capacity of 32 Gbytes (using four 4-Gbyte DIMMs). The Sun Netra CP3220 blade server accommodates the following DIMMs and configurations: ■ Up to eight standard D ...

  • Sun Microsystems CP3220 - page 54

    2-20 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 2-4 Locating DIMM Slots Populate DIMMs in matching pairs, starting with Pair 0, then adding Pair 1, Pair 2, and Pair 3 as needed. P air 0 P air 1 BA BA BA BA P air 2 P air 3 ...

  • Sun Microsystems CP3220 - page 55

    Chapter 2 Hardware Installation and Ser vice 2-21 2.3.6.2 Installing a DDR2 DIMM The following procedur e provides a general guide for installing additional memory . However , for specif ic directions on installing DIMMs on the Sun Netra CP3220 blade server , r efer to the documentation that shipped with the DIMMs. 1. Access the blade server by per ...

  • Sun Microsystems CP3220 - page 56

    2-22 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 2-5 Installing a DIMM 6. Press the top edge of the DIMM toward the blade server until the retainer clips click into place in the notches on the DIMM sides ( FIGURE 2-5 ). The small metal retainer clips on each side of the DIMM slot are spring-loaded, and they should click int ...

  • Sun Microsystems CP3220 - page 57

    Chapter 2 Hardware Installation and Ser vice 2-23 If an ESD mat is not available, you can place the blade server on the antistatic envelope in which it was packaged. Caution – Do not place blade servers on top of an antistatic bag unless the outside of the bag also has antistatic protective properties. 2. T ake antistatic precautions: Attach and ...

  • Sun Microsystems CP3220 - page 58

    2-24 Sun Netra CP3220 Blade Server User’s Guide • January 2010 2.3.7 Installing the Optional Compact Flash Car d An IDE Compact Flash card can be installed on the Sun Netra CP3220 blade server . The Compact Flash card is not hot-swappable, and there is no access to the Compact Flash card once the Sun Netra CP3220 is installed in an A TCA shelf. ...

  • Sun Microsystems CP3220 - page 59

    Chapter 2 Hardware Installation and Ser vice 2-25 FIGURE 2-7 Compact Flash Location Note – Sun Compact Flash cards have a life time of 2,000,000 write/erase cycles. Users are r esponsible for ensuring that the operating system and applications do not exceed this limitation. ...

  • Sun Microsystems CP3220 - page 60

    2-26 Sun Netra CP3220 Blade Server User’s Guide • January 2010 2.3.8 Installing Optional AMC Car ds An Advanced Mezzanine card (AMC) is a card or module that pr ovides additional functionality to the Sun Netra CP3220 blade server . The blade server contains two AMC slots in which you can install an optional AMC device. An AMC device can be inst ...

  • Sun Microsystems CP3220 - page 61

    Chapter 2 Hardware Installation and Ser vice 2-27 FIGURE 2-8 Removing an AMC Filler Panel 4. Retrieve the AMC module from its shipping kit and place it on an antistatic surface. 5. Insert the AMC module through the cutout and into the AMC slot FIGURE 2-9 . ...

  • Sun Microsystems CP3220 - page 62

    2-28 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 2-9 Installing an AMC Car d Caution – Do not use excessive force when installing the AMC module into the slot. Y ou might damage the AMC connector on the Sun Netra CP3220 blade server , causing permanent damage to the AMC module or the blade server . If the AMC module does ...

  • Sun Microsystems CP3220 - page 63

    Chapter 2 Hardware Installation and Ser vice 2-29 7. Press on the front face of the AMC card until the card is fully seated into the AMC connector . 8. Press the black ejector in, toward the AMC card, to activate the card. 9. Refer to the AMC module documentation for software and cabling installation instructions. 2.3.9 Adding or Replacing a T OD C ...

  • Sun Microsystems CP3220 - page 64

    2-30 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 2-10 Jumper 1 in the Run Position T ABLE 2-4 provides information on the pin functions on jumper 1. T ABLE 2-4 Pin Functions on Jumper 1 Pin Number Purpose Pin 1 Battery Feed Pin 2 VCC_R TC (destination for battery power) Pin 3 BA TT_CLR (r esistor to GND, used to drain capac ...

  • Sun Microsystems CP3220 - page 65

    Chapter 2 Hardware Installation and Ser vice 2-31 T o reset the jumper and r eturn the CMOS settings to the default settings, perform the following steps: 1. Remove the jumper housing from the run position (P1/P2) and move it to the reset position (P2/P3). FIGURE 2-11 Jumper 1 in the Reset Position 2. W ait at least one second for the CMOS settings ...

  • Sun Microsystems CP3220 - page 66

    2-32 Sun Netra CP3220 Blade Server User’s Guide • January 2010 2.3.10.2 Changing the OOS LED Color The color of the Out-of-service (OOS) LED can be set to red or amber by moving jumper 2 to the appropriate position. Amber is the default color for the OOS LED. T o change the Jumper 2 position to red: 1. Remove the jumper housing from the default ...

  • Sun Microsystems CP3220 - page 67

    Chapter 2 Hardware Installation and Ser vice 2-33 Users can change the default behavior of the out-of-service (OOS) LED through the IPMC by using an LED1 control bit. This bit is available only on the Sun Netra CP3220 blade server . Y ou can use the set and get IPMC control byte IPMI commands, which are the same commands used to control the Gr een ...

  • Sun Microsystems CP3220 - page 68

    2-34 Sun Netra CP3220 Blade Server User’s Guide • January 2010 ▼ V iewing OOS LED Settings ● At the clia CLI, enter the Get IPMI Control Bits command. Data Bytes Command NetFn Opcode Get IPMI Control Bits 0x2E 0xE9 T ype Byte Data Field Request Data 1 00 20 0 32 A Response Data 1 Completion Code: • [00] OK • [C1] Command not supported ? ...

  • Sun Microsystems CP3220 - page 69

    Chapter 2 Hardware Installation and Ser vice 2-35 ▼ Setting OOS LED Behavior Note – Y ou must always perform a read, modify , and write to change any of the bits in the control byte. ● At the clia CLI, enter the Set IPMI Control Bits command. Data Bytes Command NetFn Opcode Set IPMI Control Bits 0x2E 0xE9 T ype Byte Data Field Request Data 1 ...

  • Sun Microsystems CP3220 - page 70

    2-36 Sun Netra CP3220 Blade Server User’s Guide • January 2010 2.3.12 Resetting the Sun Netra CP3220 Blade Server Caution – Do not operate the A TCA shelf without all fans, component heatsinks, air baff les, and covers installed. Severe damage to components can occur if the A TCA shelf is operated without adequate cooling mechanisms. 1. Use a ...

  • Sun Microsystems CP3220 - page 71

    3-1 CHAPTER 3 Softwar e Configuration This chapter provides pr ocedures and information about configuring the softwar e. This chapter contains the following topics: ■ Section 3.1, “Operating Systems” on page 3-2 ■ Section 3.2, “Software Updates” on page 3-2 ■ Section 3.3, “SunVTS Software” on page 3-3 ■ Section 3.4, “Configuri ...

  • Sun Microsystems CP3220 - page 72

    3-2 Sun Netra CP3220 Blade Server User’s Guide • January 2010 3.1 Operating Systems The Sun Netra CP3220 blade server has been tested for compatibility with the following operating systems: ■ W indRiver Linux version 3.1 ■ Solaris 10 OS, Release S10U4 and subsequent versions that may be tested for compatibility with the Sun Netra CP3220 bla ...

  • Sun Microsystems CP3220 - page 73

    Chapter 3 Software Configuration 3-3 3.3 SunVTS Softwar e Note – The Sun V alidation T est Suite (SunVTS software) runs on the Solaris OS only . There ar e similar test suites available for the Linux operating systems. The SunVTS software is a compr ehensive software suite that tests and validates the Sun Netra CP3220 blade server by verifying th ...

  • Sun Microsystems CP3220 - page 74

    3-4 Sun Netra CP3220 Blade Server User’s Guide • January 2010 3.4 Conf iguring Sun Netra CP3220 For 1GbE or 10GbE Switches The extended fabric on the Sun Netra CP3220 blade server is capable of operating at either 1 Gbps or 10 Gbps. The Sun Netra CP3220 can be used in the Sun Netra CT 900 server with either the Sun Netra CP3240 10-GbE switch or ...

  • Sun Microsystems CP3220 - page 75

    Chapter 3 Software Configuration 3-5 3.5 Conf iguring Alternate OOS LED Behavior Administrators and service technicians can change the default behavior of the out-of-service (OOS) LED through the IPMC by using an LED1 contr ol bit. This bit is available only on the Sun Netra CP3220 blade server . Use the set and get IPMC control byte IPMI commands, ...

  • Sun Microsystems CP3220 - page 76

    3-6 Sun Netra CP3220 Blade Server User’s Guide • January 2010 ▼ Displaying Conf iguration of OOS LED Behavior Use the following command to display the current conf iguration of OOS LED behavior . Data Bytes Command NetFn Opcode Get IPMC Control Bits 0x2E 0xE8 T ype Byte Data Field Request Data 1 00 20 0 32 A Response Data 1 Completion Code: [ ...

  • Sun Microsystems CP3220 - page 77

    Chapter 3 Software Configuration 3-7 ▼ Setting Conf iguration of OOS LED Behavior Use the following command to set the configuration of OOS LED behavior . Data Bytes Note – If an attempt is made to write 0 to any reserved bit (2 to 7), IPMC will reject the command with completion code 0xCC. Command NetFn Opcode Set IPMI Control Bits 0xE9 0xE9 T ...

  • Sun Microsystems CP3220 - page 78

    3-8 Sun Netra CP3220 Blade Server User’s Guide • January 2010 ...

  • Sun Microsystems CP3220 - page 79

    4-1 CHAPTER 4 Conf iguring and Using BIOS Firmwar e This chapter describes how to use the BIOS (Basic Input Output System) to configure the blade server . This chapter contains the following topics: ■ Section 4.1, “About BIOS Settings” on page 4-2 ■ Section 4.2, “Changing the Configuration of a BIOS Menu Item” on page 4-4 ■ Section 4. ...

  • Sun Microsystems CP3220 - page 80

    4-2 Sun Netra CP3220 Blade Server User’s Guide • January 2010 4.1 About BIOS Settings This section describes how to view and modify the BIOS settings. The BIOS has a Setup utility stored in the BIOS f lash memory . The Setup utility reports system information and can be used to configur e the BIOS settings. The configur ed data is provided with ...

  • Sun Microsystems CP3220 - page 81

    Chapter 4 Configur ing and Using BIOS Firmware 4-3 4.1.2.2 AMD PowerNow! Feature Enabled by Default The AMD PowerNow! feature, which is accessed from the BIOS Setup utility Advanced menu, is enabled by default on the Sun Netra CP3220 blade server . Some problems have been observed when using this feature on certain operating systems. If you want to ...

  • Sun Microsystems CP3220 - page 82

    4-4 Sun Netra CP3220 Blade Server User’s Guide • January 2010 4.2 Changing the Conf iguration of a BIOS Menu Item Y ou can change the BIOS configuration by using a terminal (or terminal emulator connected to a computer) through the serial console port on the fr ont of the Sun Netra CP3220 blade server . Note – Using the ANSI terminal emulatio ...

  • Sun Microsystems CP3220 - page 83

    Chapter 4 Configur ing and Using BIOS Firmware 4-5 4.3 Setting the Boot Device Using BIOS Setup Scr eens Before beginning this pr ocedure, ensur e that you have installed the serial cable as described in Section 2.2.4, “Connecting External I/O Cables” on page 2-13 . Note – See Section 4.1.3, “Description of the BIOS Screens” on page 4-3 f ...

  • Sun Microsystems CP3220 - page 84

    4-6 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 4-1 BIOS Main Menu 5. Using the arrow keys, move across the top of the screen to the Boot menu and press the Enter key . The Boot Settings menu is displayed ( FIGURE 4-2 ). ...

  • Sun Microsystems CP3220 - page 85

    Chapter 4 Configur ing and Using BIOS Firmware 4-7 FIGURE 4-2 Boot Settings Menu 6. Move down the list, select the Boot Device Priority option, and press Enter . The Boot Device Priority menu is displayed ( FIGURE 4-3 ). ...

  • Sun Microsystems CP3220 - page 86

    4-8 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 4-3 Boot Device Priority Menu 7. Select the NVIDIA Boot Agent device as the 1st Boot Device. 8. Disable all unneeded boot devices in the menu. 9. Use the arrow keys to move to the Exit menu, and press Enter . The confirmation dialog box is displayed. 10. Press Enter to select ...

  • Sun Microsystems CP3220 - page 87

    Chapter 4 Configur ing and Using BIOS Firmware 4-9 4.4 Changing the BIOS Continuous Boot Setting T raditionally , the BIOS of a PC would go through the list of bootable devices and try to boot up the OS. If all devices failed to boot, BIOS would print a message to inform the user and wait for user intervention. In the A TCA environment, ther e is t ...

  • Sun Microsystems CP3220 - page 88

    4-10 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 4-4 Security Settings Menu FIGURE 4-5 Change Passwor d Menu ...

  • Sun Microsystems CP3220 - page 89

    Chapter 4 Configur ing and Using BIOS Firmware 4-11 3. Move down the list, select the Change Supervisor Password or Change User Password option, and press Enter . The Change Password menu is displayed ( FIGURE 4-5 ). 4. T ype a password, then press Enter . 5. Use the arrow keys to move to the Exit Menu. 6. Select OK to conf irm the changes you made ...

  • Sun Microsystems CP3220 - page 90

    4-12 Sun Netra CP3220 Blade Server User’s Guide • January 2010 4.7 Updating the BIOS When they become necessary , updated BIOS images will be available as patches on the following web site: http://sunsolve.sun.com/ Use the Solaris BIOS Update Utility or the Linux BIOS Update Utility to implement the updates. For more information, see the Sun Ne ...

  • Sun Microsystems CP3220 - page 91

    Chapter 4 Configur ing and Using BIOS Firmware 4-13 For example: 3. T o boot the blade server from the Shelf Manager , type: Note – Once the blade server is booted, reset the blade server to use the primary BIOS image (page 0). 4.10 Perform a Live Firmwar e Upgrade T o upgrade the BIOS firmware while r etaining the current BIOS image, follow thes ...

  • Sun Microsystems CP3220 - page 92

    4-14 Sun Netra CP3220 Blade Server User’s Guide • January 2010 4.1 1 Power -On Self-T est The system provides a rudimentary power -on self-test (POST) that runs each time the blade server boots to check the basic devices requir ed for the system to operate. The progr ess of the self-test is indicated by a series of POST codes. These codes appea ...

  • Sun Microsystems CP3220 - page 93

    Chapter 4 Configur ing and Using BIOS Firmware 4-15 4. On the Boot Settings Conf iguration screen ( FIGURE B-17 ), you can enable or disable the options shown in T ABLE 4-2 T ABLE 4-2 POST Options Option Description Quick Boot This option is disabled by default. If you enable Quick Boot, the BIOS skips certain tests while booting, such as the exten ...

  • Sun Microsystems CP3220 - page 94

    4-16 Sun Netra CP3220 Blade Server User’s Guide • January 2010 ...

  • Sun Microsystems CP3220 - page 95

    5-1 CHAPTER 5 Har dware Ar chitectur e This chapter provides information about the hardwar e architecture. This chapter contains the following topics: ■ Section 5.1, “Block Diagram” on page 5-2 ■ Section 5.2, “The AMD Opteron Pr ocessor” on page 5-3 ■ Section 5.3, “Memory” on page 5-4 ■ Section 5.4, “Networking and I/O” on p ...

  • Sun Microsystems CP3220 - page 96

    5-2 Sun Netra CP3220 Blade Server User’s Guide • January 2010 5.1 Block Diagram FIGURE 5-1 Block Diagram ...

  • Sun Microsystems CP3220 - page 97

    Chapter 5 Hardware Architecture 5-3 5.2 The AMD Opter on Processor AMD Opteron pr ocessors with Direct Connect Architectur e include several new features, including seamless quad-core upgradability and DDR2 memory . AMD Opteron pr ocessors with DDR2 memory feature a common core ar chitecture that is consistent across 1-way , 2-way , and 8-way syste ...

  • Sun Microsystems CP3220 - page 98

    5-4 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE 5-2 AMD Opter on Processors Block Diagram 5.3 Memory The Sun Netra CP3220 blade server supports 1-Gbyte, 2-Gbyte, and 4-Gbyte register ed DDR2-667 memory , for up to 32 Gbytes memory total. When four DIMM slots or less are populated, the DIMM clock rate will be set to the max ...

  • Sun Microsystems CP3220 - page 99

    Chapter 5 Hardware Architecture 5-5 5.4 Networking and I/O Networking and I/O are pr ovided by the following chips and interconnects: ■ nV idia MCP55 (southbridge) ■ PCI Express Bus ■ Dual BIOS ■ T rusted Platform Module ■ Broadcom 5715C Gbit Ethernet chip ■ Sun Sun 10 GbE Multithreaded Networking ASIC Dual 10-Gbit + Dual 1-Gbit Etherne ...

  • Sun Microsystems CP3220 - page 100

    5-6 Sun Netra CP3220 Blade Server User’s Guide • January 2010 5.4.2 PCI Expr ess Bus PCI Express 1.0 (PCIe) is a high-speed, point-to-point dual simplex chip interconnect. It is the latest extension of the PCI bus. PCI e operates at 2.5 GHz and supports land widths of x1, x2, x4, x8, x16, and x32. Additional features include: ■ Serial point-t ...

  • Sun Microsystems CP3220 - page 101

    Chapter 5 Hardware Architecture 5-7 5.4.6 Sun Dual 10-Gbit Ethernet/Quad 1-Gbit RGMII Network Interface Chip (Sun 10 GbE Multithr eaded Networking ASIC) The Sun Netra CP3220 blade server is equipped with one Sun Dual 10-Gbit Ethernet/Quad 1-Gbit RGMII Network Interface chip that is specifically designed to support multicore and multithr eaded proce ...

  • Sun Microsystems CP3220 - page 102

    5-8 Sun Netra CP3220 Blade Server User’s Guide • January 2010 5.5.2 EIDE/A T A for Compact Flash EIDE is an enhanced IDE controller , implemented through the nV idia MCP55 chip. The Sun Netra CP3220 blade server contains one on-board 50-pin T ype II Compact Flash connector , for use with an optional compact flash car d. The location of the comp ...

  • Sun Microsystems CP3220 - page 103

    A-1 APPENDIX A Physical Characteristics Specifications for the Sun Netra CP3220 blade server ar e provided in the following sections: ■ Section A.1, “Form Factor” on page A-2 ■ Section A.2, “Power and Thermal Metrics” on page A-2 ■ Section A.3, “Connectors and Pinouts” on page A-4 ...

  • Sun Microsystems CP3220 - page 104

    A-2 Sun Netra CP3220 Blade Server User’s Guide • January 2010 A.1 Form Factor The Sun Netra CP3220 blade server is a standard 8-rack unit (8U) factor , single-slot wide. It complies with the board mechanical dimensions that are r equired by the PICMG 3.0 R1.0 specification: ■ 322.25 mm x 280 mm (12.7 inches x 1 1.0 inches) ■ 30.48 mm (1.2 i ...

  • Sun Microsystems CP3220 - page 105

    Appendix A Physical Characteristics A-3 A.2.2 PICMG Boar d Cooling Requir ements T ABLE A-1 provides the blade server boar d cooling requir ements. No alarms are triggered at any of the listed temperatures for the given airf low . A.2.3 PICMG AR TM Cooling Requir ements T ABLE A-2 provides the Pressur e Drop vs. Flow Rate for the AR TM. T ABLE A-1 ...

  • Sun Microsystems CP3220 - page 106

    A-4 Sun Netra CP3220 Blade Server User’s Guide • January 2010 A.3 Connectors and Pinouts A.3.1 Fr ont Panel Connectors The front panel has the following connectors, see FIGURE 1- 1 : ■ One 10/100/1000BASE-T Ethernet port (RJ-45) ■ One serial port (RJ-45) ■ T wo USB ports A.3.1.1 Ethernet Port The Ethernet connector is an RJ-45 connector . ...

  • Sun Microsystems CP3220 - page 107

    Appendix A Physical Characteristics A-5 A.3.1.2 USB Ports FIGURE A-2 shows the connector pin assignments for both of the front panel USB ports. FIGURE A-2 Front Panel USB Connector T ABLE A-5 lists the USB port connector pin assignments. 2 DA- 6 DB- 3 DB+ 7 DD+ 4 DC+ 8 DD- T ABLE A-4 USB Port Pin Assignments Pin Signal Name Description 1 VCC +5 VDA ...

  • Sun Microsystems CP3220 - page 108

    A-6 Sun Netra CP3220 Blade Server User’s Guide • January 2010 A.3.1.3 Serial Port FIGURE A-3 shows the connector pin assignments for the front panel serial port. T ABLE A-5 lists the serial port connector pin assignments. FIGURE A-3 Front Panel Serial RJ-45 Connector A.3.2 AMC Connectors T wo 170-pin connectors make up the AMC card connections. ...

  • Sun Microsystems CP3220 - page 109

    Appendix A Physical Characteristics A-7 ■ T wo -48 VDC power feeds (four signals each; eight signals total) ■ T wo IPMB ports (two signals each; four signals total) ■ Geographic address (eight signals) The analog test and ring voltage pins are left unconnected. FIGURE A-4 shows the pin assignments. FIGURE A-4 Power Distribution Connector (Zon ...

  • Sun Microsystems CP3220 - page 110

    A-8 Sun Netra CP3220 Blade Server User’s Guide • January 2010 13 SCL_A IPMB Clock, Port A 14 SDA_A IPMB Data, Port A 15 SCL_B IPMB Clock, Port B 16 SDA_B IPMB Data, Port B 17 MT1_TIP Metallic T est #1 T ip 18 MT1_TIP Metallic T est #2 T ip 19 -RING_A Ringing Generator A Negative Ringing 20 -RING_B Ringing Generator B Negative Ringing 21 MT1_RIN ...

  • Sun Microsystems CP3220 - page 111

    Appendix A Physical Characteristics A-9 A.3.4 Data T ransport Connector (Zone 2) The data transport connector consists of two 120-pin HM-Zd connectors, labeled P20 and P23, with 40 differ ential pairs each. These are called the Zone 2 connectors. The Zone 2 connectors provides the following signals: ■ T wo 10/100/1000BASE-T/TX Ethernet base fabri ...

  • Sun Microsystems CP3220 - page 112

    A-10 Sun Netra CP3220 Blade Server User’s Guide • January 2010 A.3.5 Advanced Rear T ransition Module Connector (Zone 3) The Sun Netra CP3220 blade server provides all the I/O connections for r ear access through the Zone 3 AR TM connector . The connector view and the pinout for the Zone 3 connector are shown in FIGURE A-6 . FIGURE A-6 Zone 3 C ...

  • Sun Microsystems CP3220 - page 113

    Appendix A Physical Characteristics A-11 T ABLE A-8 shows the J31 connector pin assignments, used for AMC I/O signals. T ABLE A-8 J31 Connector Pin Assignments Row Interface A B C D E F 1 AMC1 EO Ports TX1_13+ TX1_13- RX1_12+ RX1_12- TX1_12+ TX1_12- 2 RX1_14+ RX1_14- TX1_14+ TX1_14- RX1_13+ RX1_13- 3 TX1_17+ TX1_17- RX1_15+ RX1_15- TX1_15+ TX1_15- ...

  • Sun Microsystems CP3220 - page 114

    A-12 Sun Netra CP3220 Blade Server User’s Guide • January 2010 T ABLE A-9 shows the J32 connector pin assignments, which are used for infrastructure signals. T ABLE A-10 shows the J33 connector pin assignments, which are used for PCIe signals. T ABLE A-9 J32 Connector Pin Assignments Row Interface A B C D E F 1 AMC2 EO Ports NC NC RX2_20+ RX2_2 ...

  • Sun Microsystems CP3220 - page 115

    B-1 APPENDIX B BIOS Scr eens This appendix provides examples of the first-level and second-level screens from the BIOS menu. T o enter the BIOS menu, press the F2 key during the POST portion of the boot process. FIGURE B-1 shows the BIOS menu tree. FIGURE B-2 through FIGURE B-29 show the screens within the BIOS menu tr ee. ...

  • Sun Microsystems CP3220 - page 116

    B-2 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE B-1 BIOS Menu T ree Advanced Main PCI/PnP Boot Secur ity Chipset CPU Configuration IDE Configuration Super IO Configuration A CPI Configuration Event Log Configuration MPS Configuration PCI Express Smbios Remote Clear NVRAM Plug & Pla y OS PCI Latency Timer Allocate IRQ to ...

  • Sun Microsystems CP3220 - page 117

    Appendix B BIOS Screens B-3 FIGURE B-2 BIOS Main Menu FIGURE B-3 Advanced Configuration Menu ...

  • Sun Microsystems CP3220 - page 118

    B-4 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE B-4 CPU Configuration Menu FIGURE B-5 IDE Configuration Menu ...

  • Sun Microsystems CP3220 - page 119

    Appendix B BIOS Screens B-5 FIGURE B-6 Super IO Configuration Menu FIGURE B-7 ACPI Settings Menu ...

  • Sun Microsystems CP3220 - page 120

    B-6 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE B-8 Event Logging Details Menu FIGURE B-9 MPS Configuration Menu ...

  • Sun Microsystems CP3220 - page 121

    Appendix B BIOS Screens B-7 FIGURE B-10 PCI Express Configuration Menu FIGURE B-11 SMBIOS Configuration Menu ...

  • Sun Microsystems CP3220 - page 122

    B-8 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE B-12 Remote Access Configuration Menu FIGURE B-13 USB Configuration Menu ...

  • Sun Microsystems CP3220 - page 123

    Appendix B BIOS Screens B-9 FIGURE B-14 Advanced PCI/PnP Settings Menu FIGURE B-15 Advanced PCI/PnP Settings Menu Continued ...

  • Sun Microsystems CP3220 - page 124

    B-10 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE B-16 Boot Settings Menu FIGURE B-17 Boot Settings Configuration Menu ...

  • Sun Microsystems CP3220 - page 125

    Appendix B BIOS Screens B-11 FIGURE B-18 Boot Device Priority Menu FIGURE B-19 Boot Hard Disk Drive Priority Menu ...

  • Sun Microsystems CP3220 - page 126

    B-12 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE B-20 Security Settings Menu FIGURE B-21 Change Password Settings Menu ...

  • Sun Microsystems CP3220 - page 127

    Appendix B BIOS Screens B-13 FIGURE B-22 Chipset Main Menu FIGURE B-23 NorthBridge Chipset Configuration Menu ...

  • Sun Microsystems CP3220 - page 128

    B-14 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE B-24 NorthBridge Chipset Memory Configuration Menu FIGURE B-25 NorthBridge Chipset ECC Configuration Menu ...

  • Sun Microsystems CP3220 - page 129

    Appendix B BIOS Screens B-15 FIGURE B-26 NorthBridge Chipset DRAM Configuration Menu FIGURE B-27 SouthBridge Chipset Configuration Menu ...

  • Sun Microsystems CP3220 - page 130

    B-16 Sun Netra CP3220 Blade Server User’s Guide • January 2010 FIGURE B-28 Hyper T ransport Configuration Menu FIGURE B-29 Exit Options Menu ...

  • Sun Microsystems CP3220 - page 131

    Appendix B BIOS Screens B-17 ...

  • Sun Microsystems CP3220 - page 132

    Index-1 Index A Advanced PCI/PnP Settings menu, B-9 Airflow Requirements, A-3 AMC connectors, A-6 AMC devices additional I/O, 1-7 installing, 2-26 AMC.1 T ype 4E2 cards, 1-7 B barcode labels, locating, 1-14 BIOS about settings, 4-2 AMD PowerNow!, 4-3 changing boot device, 4-5 changing configuration, 4-4 changing passwords, 4-9 screen descriptions ...

  • Sun Microsystems CP3220 - page 133

    Index-2 Sun Netra CP3220 Blade Server User’ s Guide • January 2010 contacting support, 1-14 CPU Configuration menu, B-4 D data transport connector, A-9 DDR-2 DIMM. See DIMMs, 2-19 DIMMs described, 2-19 installing, 2-21 removing, 2-22 E electric shock caution, 2-2 Ethernet, RJ-45, A-4 Event Logging Configuration menu, B-6 F front panel, A-6 H ...

  • Sun Microsystems CP3220 - page 134

    Index-3 hardwar e, 1-13 safety, 2-2 software, 1-13 revision number , locating, 1-14 RJ-45 Ethernet, A-4 R TM Pressure Dr op, A-3 S Security Settings menu, B-12 serial number , locating, 1-14 port, A-6 SMBIOS Configuration menu, B-7 software OS support, 3-2 SunVTS, 3-3 software r equirements, 1-13 Southbridge chipset menu, B-14, B-15 Sun Services, ...

  • Sun Microsystems CP3220 - page 135

    Index-4 Sun Netra CP3220 Blade Server User’ s Guide • January 2010 ...

Manufacturer Sun Microsystems Category Server

Documents that we receive from a manufacturer of a Sun Microsystems CP3220 can be divided into several groups. They are, among others:
- Sun Microsystems technical drawings
- CP3220 manuals
- Sun Microsystems product data sheets
- information booklets
- or energy labels Sun Microsystems CP3220
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sun Microsystems CP3220.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sun Microsystems CP3220, service manual, brief instructions and user manuals Sun Microsystems CP3220. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sun Microsystems CP3220.

Similar manuals

A complete manual for the device Sun Microsystems CP3220, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sun Microsystems CP3220 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sun Microsystems CP3220.

A complete Sun Microsystems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sun Microsystems CP3220 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sun Microsystems CP3220, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sun Microsystems CP3220, that we can find in the current document
3. Tips how to use the basic functions of the device Sun Microsystems CP3220 - which should help us in our first steps of using Sun Microsystems CP3220
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sun Microsystems CP3220
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sun Microsystems CP3220 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sun Microsystems CP3220?

Use the form below

If you did not solve your problem by using a manual Sun Microsystems CP3220, ask a question using the form below. If a user had a similar problem with Sun Microsystems CP3220 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)