English dropdown-ico

Manual Husqvarna 326P4, 326P5

28 pages 1.26 mb
Download

Go to site of 28

Summary
  • Husqvarna 326P4, 326P5 - page 1

    326P4 X-SERIES Operator's manual (CARB II, EP A II) Read through the Operator‘s Manual carefully and understand the content before using the machine. 101 91 63-93 ...

  • Husqvarna 326P4, 326P5 - page 2

    2 – English Symbols SYMBOL EXPLANA TION W ARNING! This machine can be dangerous. Careless or incorr ect use can result in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine. • Use anti-slip and stable boots. • Always wear approved protective g ...

  • Husqvarna 326P4, 326P5 - page 3

    English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal protective equipment ............................................. 4 The ...

  • Husqvarna 326P4, 326P5 - page 4

    4 – English The machine ‘ s saf ety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.) P ersonal pr otective equipment SAFETY INS ...

  • Husqvarna 326P4, 326P5 - page 5

    English – 5 SAFETY INSTR UCTIONS 3. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. The machine ’ s vibration damping system reduces the transfer of vibrations between the engine unit/ cutting equipment and the machine ’ s handle u ...

  • Husqvarna 326P4, 326P5 - page 6

    6 – English SAFETY INSTR UCTIONS Inspecting, maintaining and servicing machine saf ety equipment IMPORT ANT INFORMA TION • All service and repairs to the machine require special training. • This applies especially to the machine ‘ s saf ety equipment. If the machine does not meet any of the controls listed belo w you should contact y our se ...

  • Husqvarna 326P4, 326P5 - page 7

    English – 7 SAFETY INSTR UCTIONS W ARNING! Never use a machine with defective safety equipment. The safety equipment should be maintained as described in this section. If your machine does not meet any of these contr ols you should contact your service w orkshop. ! ! W ARNING! Always stop the engine bef ore carrying out any w ork on the cutting e ...

  • Husqvarna 326P4, 326P5 - page 8

    8 – English SAFETY INSTR UCTIONS Saw c hain • Saw chain pitch (inches) S pacing between drive links. • Drive link width (mm/ inches). • N umber of drive links. • Level of kickbak r eduction The level of kickback reduction offer ed by a chain is indicated by its model number . Sharpening y our chain and adjusting raker c learance W ARNING! ...

  • Husqvarna 326P4, 326P5 - page 9

    English – 9 SAFETY INSTR UCTIONS B. Sharpening cutting tooth T o sharpen cutting teeth you will need a R OUND FILE and a FILE GAUGE. 1. Check that the chain is correctly tensioned. A slack chain is difficult to sharpen correctly . 2. Always file cutting teeth from the inside face, reducing the pr essure on the return stroke. F ile all the teeth o ...

  • Husqvarna 326P4, 326P5 - page 10

    10 – English SAFETY INSTR UCTIONS D . Adjusting raker clearance • When correction of the raker clearance is made the teeth must be newly sharpened. W e recommend that you adjust the raker clearance every third time you sharpen the chain. NO TE! This recommendation assumes that the length of the cutting teeth is not reduced ex cessively . • A ...

  • Husqvarna 326P4, 326P5 - page 11

    English – 11 SAFETY INSTR UCTIONS Chec king wear on cutting equipment A. Saw chain Check the saw chain daily for: • Visible cracks in rivets and links. • Whether the chain is stiff. • Whether rivets and links are badly worn. Compare the existing chain with a new chain to decide how badly it is worn. When the length of the cutting teeth has ...

  • Husqvarna 326P4, 326P5 - page 12

    12 – English SAFETY INSTR UCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like. • When storing and tr ...

  • Husqvarna 326P4, 326P5 - page 13

    English – 13 SAFETY INSTR UCTIONS Safety instructions when using the machine ! Protective instructions while working • Always ensure you have a safe and firm working position. • Always use both hands to hold the machine. Hold the machine on the side of the body . • U se your right hand to operate the throttle. • Make sure that y our hands ...

  • Husqvarna 326P4, 326P5 - page 14

    14 – English ! Basic working techniques • The machine should be held as close to the body as possible to get the best balance. • Make sure that the tip does not touch the ground. • Do not rush the work, but work steadily until all the branches have been cut back cleanly . • Always drop to idling speed after each working operation. Longer ...

  • Husqvarna 326P4, 326P5 - page 15

    English – 15 • Use the stop at the base of the bar to provide support during cutting. This will help prevent the cutting equipment from jumping on the branch. • Make an initial cut on the underside of the branch before cutting through the branch from above. This will prevent tearing of the bark, which could lead to slow healing and cause perm ...

  • Husqvarna 326P4, 326P5 - page 16

    16 – English WHA T IS WHA T? What is what on the mac hine? 27 29 28 25 23 23 26 23 24 21 19 22 18 1 7 11 12 13 16 15 14 17 5 10 4 20 6 8 9 2 3 1. Lubricant filler hole 2. Bevel gearbox 3. Chain lubrication adjustment screw (B) 4. Chain lubrication locking screw (A) 5. Shaft 6. F ront handle 7. Throttle control 8. Stop switch 9. Throttle lock 10. ...

  • Husqvarna 326P4, 326P5 - page 17

    English – 17 ASSEMBL Y Fitting the cutting head • Fit the cutting head on the shaft so that the screw (A) is aligned with the hole in the shaft as shown. • Tighten screw A. • Tighten screw B. NOTE! Make sure that the drive shaft inside the shaft engages with the cut-out in the cutting head. Mounting guide bar and chain • Unscrew the bar n ...

  • Husqvarna 326P4, 326P5 - page 18

    18 – English FUEL HANDLING Fuel mixture ! W ARNING! Always pr ovide good ventilation when handling fuel. NO TE! The machine is fitted with a two-stroke engine and must always be run on a mixture of gasoline and two-stroke oil. I t is important to measure the quantity of oil accurately , to ensure the correct mixtur e ratio. S mall discrepancies i ...

  • Husqvarna 326P4, 326P5 - page 19

    English – 19 ST AR T AND ST OP Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Warm engine U se the same star ting procedure as for the col ...

  • Husqvarna 326P4, 326P5 - page 20

    20 – English Fine adjustment • When the machine has been ” run-in ” the carburetor should be finely adjusted. The fine adjustment should be carried out by qualified person. First adjust the L-jet, then the idling screw T and then the H-jet. Conditions • Before any adjustments are made the airfilter should be clean and the airfilter cover ...

  • Husqvarna 326P4, 326P5 - page 21

    English – 21 Correctly adjusted carburetor A correctly adjusted carbur etor means that the machine accelerates without hesitation and the machine 4-cycles a little at max speed. F ur thermore, the cuttingequipment, must not rotate/mo ve at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration. A too l ...

  • Husqvarna 326P4, 326P5 - page 22

    22 – English MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4. Cylinder cover (leads cold air onto the cylinder). Clean the cooling ...

  • Husqvarna 326P4, 326P5 - page 23

    English – 23 MAINTENANCE NO TE: Use only HUSQ V ARNA replacement parts. U se of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Y our warranty does not cov er damage or liability caused by the use of accessories and/or attachments not specifically recommended b y HUSQ V ARNA. Maintenance schedu ...

  • Husqvarna 326P4, 326P5 - page 24

    24 – English TECHNICAL D A T A 326P4 1,50/24,5 1,34/34 1,06/27 12 500 2700 0,9kW/ 9000 rpm Ye s Ye s W albro MB Champion R CJ 6Y 0,02/0,5 Zama C1Q 1,06/0,5 11,9/5,4 94 105 2,2/2,6 6,6/7,5 T echnical data Engine Cylinder capacity , cu. in/cm 3 Cylinder bor e, inch/mm S troke length, inch/mm Recommended max. speed, rpm I dling speed, rpm Max. engin ...

  • Husqvarna 326P4, 326P5 - page 25

    English – 25 1 5 L Type Inch Inch/mm Inch/mm Angle Angle Angle Inch/mm Inch/cm: dl 91VG 3/8" 0,050"/1,3 5/32" /4,0 85 ° 30 ° 0 ° 0,025"/0,65 10"/25:40 12"/30::45 S36 3/8" 0,050"/1,3 5/32" /4,0 85 ° 30 ° 0 ° 0,025"/0,65 10"/25:40 12"/30:45 Bar and chain combinations The following co ...

  • Husqvarna 326P4, 326P5 - page 26

    26 – English ´*30G¶3L¨ Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & G ...

  • Husqvarna 326P4, 326P5 - page 27

    ...

  • Husqvarna 326P4, 326P5 - page 28

    2001W22 ´*30G¶3L¨ ...

Manufacturer Husqvarna Category Chainsaw

Documents that we receive from a manufacturer of a Husqvarna 326P4, 326P5 can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- 326P4, 326P5 manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna 326P4, 326P5
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna 326P4, 326P5.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna 326P4, 326P5, service manual, brief instructions and user manuals Husqvarna 326P4, 326P5. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna 326P4, 326P5.

Similar manuals

A complete manual for the device Husqvarna 326P4, 326P5, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna 326P4, 326P5 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna 326P4, 326P5.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna 326P4, 326P5 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna 326P4, 326P5, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna 326P4, 326P5, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna 326P4, 326P5 - which should help us in our first steps of using Husqvarna 326P4, 326P5
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna 326P4, 326P5
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna 326P4, 326P5 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna 326P4, 326P5?

Use the form below

If you did not solve your problem by using a manual Husqvarna 326P4, 326P5, ask a question using the form below. If a user had a similar problem with Husqvarna 326P4, 326P5 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)