English dropdown-ico

Manual Genie 1024

28 pages 4.73 mb
Download

Go to site of 28

Summary
  • Genie 1024 - page 1

    SA VE THIS MANUAL FOR FUTURE REFERENCE For Answers and Assist ance: 1.800.354.3643 or visit www .geniecompany .com Model 1022/1024 Includes Remote Control (Up to 7 Single Button Programmable Controls Available) Homelink ® and Car2U™ compatible Homelink ® is a registered trademark of Johnson Controls T echnology Company . Car2U ™ is a trademar ...

  • Genie 1024 - page 2

    PN# 3642036212, 8/09/2007 2 Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on the owner or user of this system to read, understand and implement the inform ...

  • Genie 1024 - page 3

    PN# 3642036212, 8/09/2007 3 T ABLE OF CONTENTS OPERA T OR FEA TURES INTELLICODE ® Rolling Code Security System. An electronic rolling code system that enhances the security of the door operator by continuously changing the access code each time the remote control is used. The door operator responds to each new code only once. An access code copied ...

  • Genie 1024 - page 4

    PN# 3642036212, 8/09/2007 6 T o avoid damage to your door and/or operator , make sure you disable and/or remove any door locks, ropes, and/or cables prior to inst alling your operator . ( Refer to Section 1.) 4 PRE-INST ALLA TION CHECK LIST FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM Things to consider if you are planning to "Do-it-your ...

  • Genie 1024 - page 5

    PN# 3642036212, 8/09/2007 5 TYPICAL SECTIONAL DOOR INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM TYPICAL SUPPORT BRACKET EXTENSION SPRING OR TORSION SPRING SAFETY BEAMS BRACES ADDED HEADER BRACKET MOUNTING BOARD POWER CORD (APPROX. 45 IN.) TO 120V GROUNDED OUTLET 4 1 3 6 2 3 5 SECTIONAL DOOR Pg. 18 Pg. 12 Pg. 1 1-12 Pg. 13 Pg. 1 ...

  • Genie 1024 - page 6

    PN# 3642036212, 8/09/2007 6 RECOMMENDED TOOLS FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 3/16" Drill Bit 1/4", 7/16", 3/8" and 1/2" Sockets S tep ladder Drill Ratchet Carpenter ’ s level Pencil T ape measure Wire strippers Phillips screwdrivers Adjustable wrench P AR TS IDENTIFICA TION - Not Shown Full Size . Thre ...

  • Genie 1024 - page 7

    PN# 3642036212, 8/09/2007 F ASTENERS - Shown Full size ( See Parts List below for full description.) Lag screw - 5/16" x 2" Self-drilling Screw 1/4"-20 x 3/4" Hex Flange Nut - 1/4"-20 Cotter pin Clevis pin 5/16" x 3/4" Hex Bolt - 5/16"-18 x 3/4" Hex Flange Nut - 5/16"-18 Rail Clamp Bolt - 5/16" ...

  • Genie 1024 - page 8

    PN# 3642036212, 8/09/2007 8 1-PIECE RAIL HARDW ARE ASSEMBLED VIEW FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 3-PIECE RAIL HARDW ARE ASSEMBLED VIEW Chain tensioner Rail with chain Chain T rolley Slide Release Knob Header Bracket Po wer Head Po wer Cord Clevis Pin, Long & Cotter Pin N O T E Som e d o ors need bra cin g. Con tac t door dis ...

  • Genie 1024 - page 9

    PN# 3642036212, 8/09/2007 9 OPERA T OR ASSEMBL Y FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 1 NOTE: Three (3) piece rail assemblies are for a 7 foot high door . Clear a workspace area to unp ack and organize box and contents for assembly . 1. There are 4 boxes inside the carton. Each box is numbered 1 - 4. Note that some operators will cont ...

  • Genie 1024 - page 10

    10 POWER HEAD & RAIL ASSEMBL Y FIG . 1-5 Chain adjustment . FIG . 1-4 Rail - Power head assembly . NOTE: Handle carefully! Drive chain can slide out of rail. NOTE: For power head and rail assembly locate Bag 1 from Box 1. 1. Attach rail assembly to power head by aligning the sprocket onto the motor shaf t. Use (3) bolts, 5/16"-18 x 1/2&quo ...

  • Genie 1024 - page 11

    PN# 3642036212, 8/09/2007 11 FIG . 2-2 Finding highest point of travel . INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 2 HEADER AND DOOR MOUNTING BRACKETS: 1. Finding header bracket mounting location . • Close garage door . – Use a pencil and level. a) Mark center of garage door (one-half overall width) on the wall with 6&qu ...

  • Genie 1024 - page 12

    12 MOUNTING THE OPERA T OR: 1. Getting started . • Position assembled rail on wall next to header bracket. (Fig. 2-4) . – Place material on floor under power head to protect from scratching. (A box, stool, or similar device may be needed to clear a torsion spring.) NOTE: For header bracket pins locate Bag 2 from Box 1. 2. Mounting the assembly ...

  • Genie 1024 - page 13

    PN# 3642036212, 8/09/2007 13 DOOR BRACKET : NOTE: For door bracket and bolts locate Bag 4 from Box 2. 1. Finding door bracket mounting location . • Door bracket is mounted as high on door as possible along vertical centerline and NO LOWER THAN top set of rollers (Fig. 2-7) . 2. Mounting the door bracket . • Proper bracing should be verified at ...

  • Genie 1024 - page 14

    14 NOTE: For Wall Control, wire and insulated staples locate Bags 6 and 7 from Box 2. 1. Wall Control location. • Wall Control location should be in direct sight of door . • It should be at least five feet (5') above floor to prevent small children from operating door . • It must be away from any moving parts. (Y ou should NOT be able to ...

  • Genie 1024 - page 15

    PN# 3642036212, 8/09/2007 15 3.Securely fasten wires. • Securely fasten wires to ceiling and wall using insulated staples provided. – Use insulated staples. – S taples should be snug only . • If rear cover is attached to power head, remove it. • On power head: – Route wall control wires through wire guide. – S plit and strip ends of w ...

  • Genie 1024 - page 16

    PN# 3642036212, 8/09/2007 16 SAFETY BEAM SYSTEM INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 4 NOTE: The operator will not close the door automatically unless the Safety Beam System is installed. NOTE: For Sensors, screws, wire, and insulated staples locate items and Bag 8 from Box 3. 1. Mounting brackets . • Mark both sides ...

  • Genie 1024 - page 17

    PN# 3642036212, 8/09/2007 17 3b. Wiring (pre-wired) . • Route wire from wall to Safety Beam sensors. (Fig. 4-5b) . • S plice pre-wiring to shortened sensor wire, match wire pairs dash-to-dash and plain-to-plain . - T rim sensor wire to approximately one foot (1 ft) from sensor . - S plit and strip ends of sensor wires and pre-wired wires. (Fig. ...

  • Genie 1024 - page 18

    PN# 3642036212, 8/09/2007 18 CONNECTING TO POWER FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 5 Plug the operator into a properly grounded electrical outlet. (Fig. 5-1) • T o reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third ( grounding ) pin. This plug will only fit a grounded type outlet. I ...

  • Genie 1024 - page 19

    PN# 3642036212, 8/09/2007 19 DOOR LIMITS FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 6 The OPEN (UP) and CLOSE (DOWN) door positions are controlled by making the adjustments on the panel located on the bottom of the power head. The adjustments that can be made are: Close T ravel Limit, Open T ravel Limit, Maximum Closing Force, Maximum Openi ...

  • Genie 1024 - page 20

    PN# 3642036212, 8/09/2007 FIG . 6-5 2 x 4 under center of door opening. CONT ACT REVERSE TEST The force adjustment s and limit switch settings MUST BE COMPLETED before testing. 1. T esting . • Open garage door using wall control. – Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 6-5) . • Close door using ...

  • Genie 1024 - page 21

    PN# 3642036212, 8/09/2007 21 FCC and IC CER TIFIED FIG . 7-1 Learn code button and LED SET SET OPEN FORCE CL OSE C ODE LEARN LIMIT MANU AL Open T ravel Limit Open Set Limit Button Close T ravel Limit Close Set Limit Button Down Forc e Contr ol Adjustment Up Force Contr ol Adjustment Learn Code Button LED Indicator Light To Garage Door This device c ...

  • Genie 1024 - page 22

    PN# 3642036212, 8/09/2007 22 REMOTE CONTROL BA TTERY REPLACEMENT AND VISOR CLIP INST ALLA TION 8 FIG . 8-1 Open battery cover . 1. Battery replacement . • Use coin, ball-point pen or similar device. – Gently push straight in on battery cover lock tab as shown (Fig. 8-1) . • Flip open battery cover . – Remove old battery . • Make sure new ...

  • Genie 1024 - page 23

    PN# 3642036212, 8/09/2007 Use wall control supplied with operator . Any other wall control can cause the operator to operate unexpectedly . CAUTION If you have any questions, please do not hesitate to cont act customer service at: 1.800.354.3643 23 IMPORT ANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or ...

  • Genie 1024 - page 24

    PN# 3642036212, 8/09/2007 24 CIRCUIT WIRING DIAGRAM FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 1 2 3 4 5 6 1 2 3 4 12 3 1 2 POWER CORD CORDON DE SECTEUR CABLE ELÉCTRICO TERMINAL BLOCK BORNE BLOQUE DE TERMINALES WHITE BLANC BLANCO BLACK NOIR NEGRO GREEN VERT VERDE SURGE PROTECTOR (MOV) LIMITEUR DE SURTENSION PROTECTOR DE SOBRETENSIONES TRAN ...

  • Genie 1024 - page 25

    PN# 3642036212, 8/09/2007 TROUBLESHOOTING GUIDE - OPERA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM PROBLEM WHA T TO DO Operator does NOT run from wall control. • Check power source. – Plug a lamp into outlet used for power head. If lamp works, power source is OK . – If not, check fuse or circuit breaker . • If power is OK. – ...

  • Genie 1024 - page 26

    PN# 3642036212, 8/09/2007 26 TROUBLESHOOTING GUIDE - POWER HEAD LED FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM Power head LED Possible Problem Solution Red LED showing Green LED showing OFF OFF Normal operation None required Continuous ON • Programming incomplete • Complete programming 1 BLINK, Pause (Repeat) • T ransmitter has not le ...

  • Genie 1024 - page 27

    PN# 3642036212, 8/09/2007 T ransmitters comply with all United S tates and Canadian legal requirements as of the date of manufacture. No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another country , the importer must determine compliance with any local laws and regulatio ...

  • Genie 1024 - page 28

    PN# 3642036212, 8/09/2007 28 The Genie Comp any Professional Access Systems LIMITED W ARRANTY What is covered: Any defect in material and product workmanship from personal, normal household use in accordance with the Owner ’ s Manual. For how long: Limited 1 year warranty on parts, 5 years on motor . Who gets the warranty: This warranty is limite ...

Manufacturer Genie Category Garage Door Opener

Documents that we receive from a manufacturer of a Genie 1024 can be divided into several groups. They are, among others:
- Genie technical drawings
- 1024 manuals
- Genie product data sheets
- information booklets
- or energy labels Genie 1024
All of them are important, but the most important information from the point of view of use of the device are in the user manual Genie 1024.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Genie 1024, service manual, brief instructions and user manuals Genie 1024. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Genie 1024.

Similar manuals

A complete manual for the device Genie 1024, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Genie 1024 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Genie 1024.

A complete Genie manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Genie 1024 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Genie 1024, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Genie 1024, that we can find in the current document
3. Tips how to use the basic functions of the device Genie 1024 - which should help us in our first steps of using Genie 1024
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Genie 1024
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Genie 1024 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Genie 1024?

Use the form below

If you did not solve your problem by using a manual Genie 1024, ask a question using the form below. If a user had a similar problem with Genie 1024 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)