-
Roland RG-3M - page 1
04567423 08-04-3N * 04567423 - 03 * ...
-
Roland RG-3M - page 2
...
-
Roland RG-3M - page 3
201b Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS” (p. 2), “USING THE UNIT SAFELY” (p. 3–5), and “IMPORTANT NOTES” (p. 6–8). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good gras ...
-
Roland RG-3M - page 4
2 IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION : RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilater ...
-
Roland RG-3M - page 5
3 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. .......................................................................................................... 001-50 • Connect mains plug of this model to a mains socket outlet with a protective earthing connection. ........... ...
-
Roland RG-3M - page 6
4 012a • Immediately turn the power off, remove the power cord from the outlet, and request servicing by your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page when: • The power-supply cord, or the plug has been damaged; or • If smoke or unusual odor occurs • Objects ha ...
-
Roland RG-3M - page 7
5 108d • If you need to move the instrument, take note of the precautions listed below. At least three persons are required to safely lift and move the unit. It should be handled carefully, all the while keeping it level. Make sure to have a firm grip, to protect yourself from injury and the instrument from damage. 1 • Check to make sure the bo ...
-
Roland RG-3M - page 8
6 IMPORTANT NOTES 291b In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 3–5, please read and observe the following: Power Supply 301 • Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled by an inverter (such as a ref ...
-
Roland RG-3M - page 9
7 IMPORTANT NOTES Automatic Keyboard Add • While the automatic keyboard is in operation, avoid doing anything that could hamper the action of the keys, such as using undue force to press a key, or forcing up a depressed key. By doing so, you risk causing malfunction and/or damage to the keyboard. Additional Precautions 551 • Please be aware tha ...
-
Roland RG-3M - page 10
8 IMPORTANT NOTES Using USB Memory 704 (edit) • When connecting USB memory, make sure to press it until it is fully inserted. 705 (edit) • Never touch the terminals of the USB memory. Also, avoid getting the terminals dirty. 708 • USB memory is constructed using precision components; handle the cards carefully, paying particular note to the f ...
-
Roland RG-3M - page 11
9 Introduction Thank you, and congratulations on your choice of the Roland RG-3M Digital Grand Piano. The RG-3M is sure to be highly appreciated, not only for the authentic piano performances it offers, but also for its extensive selection of player piano functions. In order to enjoy reliable performance of your new keyboard for many years to come, ...
-
Roland RG-3M - page 12
10 Introduction • The RG-3M also is programmed with 20 carefully selected performance tones, including two types of grand piano tones, which you can select according to your own taste. What’s more, the settings for the “key touch,” “hammer response,” and other precision tone adjustment settings that performers demand can be stored in th ...
-
Roland RG-3M - page 13
11 Contents IMPORTANT SAFETY INSTRUCTIONS ...................................... 2 USING THE UNIT SAFELY ....................................................... 3 IMPORTANT NOTES .............................................................. 6 Introduction ......................................................................... 9 Main Features ... ...
-
Roland RG-3M - page 14
12 Contents Using the Remote Control ...................................................................................................... 32 Installing Batteries in the Remote Control ..................................................................................... .3 2 How to Use the Remote Control............................................ ...
-
Roland RG-3M - page 15
13 Contents Changing the Tuning .............................................................................................................. 67 Setting the Tonic ................................................................................................................................. 68 Playing Different Tones with the Left and Right Hands ...
-
Roland RG-3M - page 16
14 Contents Playing the Automatic Demos ............................................................................................... 98 Muting or Reducing the Volume of a Specific Part (Minus One/Guide) ..................... 99 Changing the Notation Display Settings .......................................................................... 100 S ...
-
Roland RG-3M - page 17
15 Panel Descriptions Front Panel fig.00-010 1 [Power] switch Turns the power on/off (p. 20). 2 [Volume] knob Adjusts the overall volume level (p. 20). 3 [Brilliance] knob Adjusts the tone brightness (p. 20). 4 Tone buttons They are used to choose the kinds of tones (tone groups) played by the keyboard (p. 55). [Piano 1] button [Piano 2] button [Ha ...
-
Roland RG-3M - page 18
16 Panel Descriptions Jack Panel (Left Side of Bottom Panel) fig.00-020 1 Phones jacks Headphones can be connected here (p. 21). 2 Mic Volume knob Adjusts the volume level for the microphone (p. 21). 3 Mic jack Used for connecting a microphone (p. 21). 4 Aux Input jack You can connect other sound generating devices or audio equipment here and have ...
-
Roland RG-3M - page 19
17 Panel Descriptions fig.00-030 CD Drive (Right Side of Bottom Panel) 1 Access Indicator This indicator will light when the inserted CD is being read. 2 Disc Tray Place the CD to be loaded on this tray (p. 28). 3 Emergency Eject Hole This hole allows the disc tray to be opened in case of an emergency (p. 29). 4 Eject Button Press this button to ej ...
-
Roland RG-3M - page 20
18 Before You Start Playing Opening and Closing the Top Raising the Music Rest add Always be sure to raise the music rest in the upright position before opening and raising the piano top. Be sure to fold down the music rest in the upright position after closing the piano top. 1. Gently raise the music rest, then secure it in place. fig.00-0310 2. T ...
-
Roland RG-3M - page 21
19 Before You Start Playing Opening and Closing the Lid fig.00-0350 1. To open the lid, hold handles with both hands and lift it straight up. Then, slide it to the rear. 2. To close the lid, hold handles with both hands and slowly pull it forward until it stops. Then, gently lower it into place. add • When opening and closing the lid, be careful ...
-
Roland RG-3M - page 22
20 Before You Start Playing Turning the Power On and Off 941 NOTE Turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. ■ Turning On the Power 1. Turn the [Volume] knob all the way down. 2. Press the [Power] switch. When you ...
-
Roland RG-3M - page 23
21 Before You Start Playing Connecting Headphones The RG-3M has two jacks for plugging in headphones. This allows two people to listen through headphones simultaneously, making it very useful for lessons and performing piano pieces for four hands. Additionally, this allows you to play without bothering others around you, even at night. fig.00-0420 ...
-
Roland RG-3M - page 24
22 Before You Start Playing Connecting USB Memory You can connect USB memory (sold separately) to the RG- 3M’s Ext Memory port. Connecting external USB memory enables you to do the following: • Play back songs stored on the USB memory. • Save songs recorded on the RG-3M to the USB memory. • Copy songs in the USB memory to the RG-3M’s User ...
-
Roland RG-3M - page 25
23 Before You Start Playing About the Screens Immediately after the power is turned on, the Song Select screen like the one below is displayed. ■ Main Screens Song Select Screen When you press the [Song] button, the following screen is displayed. Each time you press the [Song] button in this screen, the song genre is switched. fig.00-0480d Functi ...
-
Roland RG-3M - page 26
24 Chapter 1. Playing Back Songs Look at What You Can Do with the RG-3M! ● Listen to the Internal Songs The various internal songs programmed in the RG-3M are categorized into “Jazz” and “Classical” genres. You can play back the songs in these genres in a variety of ways, playing all the songs in sequence or randomly, or just playing song ...
-
Roland RG-3M - page 27
25 Chapter 1. Playing Back Songs Listening to Songs The RG-3M features a variety of internal songs. The internal songs are categorized into “Jazz” and “Classical” genres. Try giving these songs a listen. You can also use the RG-3M’s CD drive to play back the included CD, CD- ROMs with songs saved in SMF format, commercially available audi ...
-
Roland RG-3M - page 28
26 Chapter 1. Playing Back Songs ■ Listening to the Tone Demos The factory settings have tone demos registered in the “Favorites” (p. 25). 1. Press the [Song] button one or more times to select “Favorites” as the genre. fig.01-011d 2. Press the [ ] button to start playback of the tone demos. You can select the tone demo to play back by pr ...
-
Roland RG-3M - page 29
27 Chapter 1. Playing Back Songs Playing Back One Song To play a single selected song, use the following procedure. 1. Press the [Function] (Exit) button, getting its indicator to light. 2. Press the [Song] (Select -) button or [ ] (Select +) button to display the PLAY screen. fig.01-030d 3. Press the [Song] (Select -) button or [ ] (Select +) butt ...
-
Roland RG-3M - page 30
28 Chapter 1. Playing Back Songs ■ Listening to Songs on CDs You can play back audio CDs, CD included with the RG-3M, player piano CDs and CD-ROMs containing saved SMF music files. * You can also play songs on VIMA CD-ROMs (VIMA TUNES) sold by Roland. add Precautions Concerning Use of the CD • You cannot play back CD-R/RW disks to which audio t ...
-
Roland RG-3M - page 31
29 Chapter 1. Playing Back Songs Playing Back Songs on CDs You can play back the CD included with the RG-3M, CDs with player piano CDs, audio CDs, and CD-ROMs to which SMF music files are saved. 1. Place the CD you want to play in the CD drive. 2. Press the [Song] button one or more times to select “CD” as the genre. If using the remote control ...
-
Roland RG-3M - page 32
30 Chapter 1. Playing Back Songs 4. Press the [ ] button once more to stop playback of the songs. If you want to playback at each song, refer to “Playing Back One Song” (p. 27). NOTE • If a single folder contains 500 or more files and folders, some files or folders may not be displayed. • Files that have names starting with “.” (dot) ar ...
-
Roland RG-3M - page 33
31 Chapter 1. Playing Back Songs ■ Listening to Songs on USB Memory Not only can you listen to the songs on CDs, but you can also listen to songs saved on USB memory devices connected to the Ext Memory port. 1. Connect the USB memory containing the songs you want to play to the Ext Memory port. 2. Press the [Song] button one or more times to sele ...
-
Roland RG-3M - page 34
32 Chapter 1. Playing Back Songs Using the Remote Control You can use the included remote control to easily start and stop performances and switch songs. You can also use the remote control to select what is to be displayed on an external screen or television set connected to the RG-3M and assign functions to the buttons used in operating the remot ...
-
Roland RG-3M - page 35
33 Chapter 1. Playing Back Songs ■ How to Use the Remote Control When using the remote control, aim the remote control at the infrared receiver, keeping in mind the range of operation (below). fig.01-110 add Precautions Concerning Use of the Remote Control • The remote control is able to transmit only one operation at a time. • The remote con ...
-
Roland RG-3M - page 36
34 Chapter 1. Playing Back Songs ■ About the Remote Control fig.01-120 Button Explanation 1 TRANSFORM This changes the vocals from the microphone. You can also use this to change vocals on the CD included with the instrument (p. 41). The transform setting switches each time you press the button. “Male” → “Female” → “Kids” → “O ...
-
Roland RG-3M - page 37
35 Chapter 1. Playing Back Songs 3 INTERNAL Selects the internal song genre. The internal song genre selection changes when the [INTERNAL] button is pressed. “Jazz” → “Classical” → “Jazz” .... FAVORITES Selects the “Favorites” genre. * This group cannot be selected if no songs have been saved to the “Favorites.” EXTERNAL Sel ...
-
Roland RG-3M - page 38
36 Chapter 1. Playing Back Songs Changing the Song Tempo This changes the song tempo. Changing the tempo has no effect on the pitch of the notes. And you can change the tempo even when the song is in progress. 1. Press the remote control’s TEMPO [-] or TEMPO [+] button to adjust the tempo of the song. The tempo is indicated in the external displa ...
-
Roland RG-3M - page 39
37 Chapter 1. Playing Back Songs ■ Changing the Key of the Song Being Played (Playback Transpose) You can play back SMF music files and your own recorded performances with the notes transposed. You can also transpose the playback of songs on audio CDs and audio files. This function lets you change song keys to suit the singer‘s own vocal range. ...
-
Roland RG-3M - page 40
38 Chapter 1. Playing Back Songs 8. Press the [Function] (Exit) button so the indicator goes out. 9. Press the [ ] button to start playing the song. The song is played in the changed key. * Playback Transpose is cancelled (switched off) when you switch to a different song. Transposing the Song and Keyboard Separately You can transpose the song and ...
-
Roland RG-3M - page 41
39 Chapter 1. Playing Back Songs ■ Adding Echo to the Mic Vocals (Mic Echo) This adjusts the microphone echo when a microphone is connected to the RG-3M. 1. Press the [Function] (Exit) button so the indicator is lit. 2. Press the [Song] (Select -) button or [ ] (Select +) button to display the MIC ECHO screen. fig.01-160d 3. Press the [Song] (Sel ...
-
Roland RG-3M - page 42
40 Chapter 1. Playing Back Songs ■ Adding Harmonies to the Mic Vocals (Harmony) You can sing with a harmony accompaniment, even when you’re playing solo. This is called the “Harmony” function. 1. Press the [Function] (Exit) button so the indicator is lit. 2. Press the [Song] (Select -) button or [ ] (Select +) button to display the VOCAL sc ...
-
Roland RG-3M - page 43
41 Chapter 1. Playing Back Songs ■ Altering Vocals (Transformer) You can modify the way your voice sounds through the microphone. This is called the “Voice Transformer” function. 1. Press the [Function] (Exit) button so the indicator is lit. 2. Press the [Song] (Select -) button or [ ] (Select +) button to display the VOCAL screen. fig. 3. Pr ...
-
Roland RG-3M - page 44
42 Chapter 1. Playing Back Songs Copying Songs You can copy performances recorded with the RG-3M, songs saved on CD- ROMs, songs on USB memory connected to the RG-3M’s Ext Memory port, and other songs to the RG-3M’s “Favorites.” Copying songs to the “Favorites” enables you to access these songs easily by pressing the [Song] button to se ...
-
Roland RG-3M - page 45
43 Chapter 1. Playing Back Songs 7. Press the [ ] (Value -) button or [ ] (Value +) button to change the “From” setting. 8. Press the [Song] (Select -) button or [ ] (Select +) button so that the “COPY From” song number is flashing. fig.01-260d 9. Press the [ ] (Value -) button or [ ] (Value +) button to select the number of the song you wa ...
-
Roland RG-3M - page 46
44 Chapter 1. Playing Back Songs 13. Press the [Song] (Select -) button or [ ] (Select +) button so that the “COPY To” song number is flashing. fig.01-280d 14. Press the [ ] (Value -) button or [ ] (Value +) button to select the copy-destination number. 15. Press the [Moving Key] (Enter) button. A confirmation message appears in the screen. fig ...
-
Roland RG-3M - page 47
45 Chapter 1. Playing Back Songs Deleting Songs Saved to the “Favorites” and USB Memory This deletes songs saved to USB memory (sold separately) and the “Favorites.” If deleting songs saved to USB memory, connect the USB memory device to the Ext Memory port. 1. Press the [Function] (Exit) button so the indicator is lit. 2. Press the [Song] ...
-
Roland RG-3M - page 48
46 Chapter 1. Playing Back Songs 6. Press the [ ] (Value -) button or [ ] (Value +) button to change the delete setting. 7. Press the [Song] (Select -) button or [ ] (Select +) button to get the song number to flash. fig.01-360d 8. Press the [ ] (Value -) button or [ ] (Value +) button to select the song to be deleted. 9. Press the [Moving Key] (En ...
-
Roland RG-3M - page 49
47 Chapter 2. Using the RG-3M with an External Display or Television You can connect a computer monitor or other external display or a television to the RG-3M, enabling you to display the Song Select screen, your favorite images, song lyrics, and notations on a larger screen. add For more information about external display settings, refer to “Sel ...
-
Roland RG-3M - page 50
48 Chapter 2. Using the RG-3M with an External Display or Television Turning the Power Off After use, turn off the power using the following procedure. 1. Turn the volume all the way down on the RG-3M. 2. Turn off the RG-3M. 3. Turn off the connected display. ■ Changing the Display Settings 1. Press the [Function] (Exit) button so the indicator i ...
-
Roland RG-3M - page 51
49 Chapter 2. Using the RG-3M with an External Display or Television Connecting a Television fig.02-040 ■ Making the Connections * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 1. Turn off the power to the RG-3M and the televisio ...
-
Roland RG-3M - page 52
50 Chapter 2. Using the RG-3M with an External Display or Television Selecting What is To Be Displayed on the External Display or Television Here’s how you can specify what it is that you want to have displayed on the external display or television connected to the RG-3M. 1. Press the remote control’s [DISPLAY] button to switch the content disp ...
-
Roland RG-3M - page 53
51 Chapter 2. Using the RG-3M with an External Display or Television Displaying Favorite Images on an External Display or Television ( Slide Show) With the RG-3M, you can display desired image data (slide shows) saved to USB memory on a connected external display or television screen. You can also use VIMA CD-ROMs (VIMA TUNES) sold by Roland. This ...
-
Roland RG-3M - page 54
52 Chapter 2. Using the RG-3M with an External Display or Television 4. Press the [ ] (Value -) button or [ ] (Value +) button to set the time a single image is to be displayed. Value: 2–60 5. Press the [Function] (Exit) button so the indicator goes out. Running Slide Shows Through a Connected External Display or Television 1. Make sure the power ...
-
Roland RG-3M - page 55
53 Chapter 2. Using the RG-3M with an External Display or Television ■ When Using a VIMA CD-ROM (VIMA TUNES) 1. Place the VIMA CD-ROM (VIMA TUNES) in the CD drive. “CD” is select for the song genre automatically. 2. Press the [ ] (Select +) button or [ ] (Value +) button to select the song you want to play back. 3. Pressing the remote control ...
-
Roland RG-3M - page 56
54 Chapter 2. Using the RG-3M with an External Display or Television Changing the Background for the Lyrics Screen You can have the background you prefer shown when displaying lyrics on an external display or television screen. Preparing the Images to be Displayed Prepare the desired image data on your computer and save the data to the USB memory. ...
-
Roland RG-3M - page 57
55 Chapter 3. Performance Performing with a Variety of Sounds The RG-3M contains 20 different internal tones. The tones are organized into five tone groups, which are assigned to the Tone buttons. fig.03-010 Selecting a Tone Group 1. Press any Tone button. The indicator of the button you pressed will light. When you play the keyboard, you will hear ...
-
Roland RG-3M - page 58
56 Chapter 3. Performance ■ Changing the Volume Balance of the Layered Tones (Layer Balance) Some tones enable you to perform with two tones layered together. These are called “Layer tones.” When you select a Layer tone, you can also change the balance in the volume of the two Layer tones. 1. Press the [Function] (Exit) button so the indicato ...
-
Roland RG-3M - page 59
57 Chapter 3. Performance Making Fine Adjustments to the Piano Sound (Piano Customize) You can make fine adjustments to the sound of the piano as desired. ■ Adjusting the Keyboard Touch (Key Touch) You can adjust the touch (playing feel) of the keyboard. 1. Press the [Function] (Exit) button so the indicator is lit. 2. Press the [Song] (Select -) ...
-
Roland RG-3M - page 60
58 Chapter 3. Performance ■ Changing the Timing of Sounds According to the Force Used to Press the Keys (Hammer Response) This adjusts how your playing strength will affect the timing at which the note sounds. This is called the “Hammer Response” function. On an acoustic piano, pressing a key moves a hammer, which strikes a string to produce ...
-
Roland RG-3M - page 61
59 Chapter 3. Performance ■ Playing Sounds When the Keys Are Released (Key Off Resonance) You can play the “key off” sound (the subtle sound produced when the keys are released) obtained when playing an acoustic piano. 1. Press the [Function] (Exit) button, getting its indicator to light. 2. Press the [Song] (Select -) button or [ ] (Select + ...
-
Roland RG-3M - page 62
60 Chapter 3. Performance ■ Producing the Resonance of the Strings When the Keys Are Played (String Resonance) When you play the keys on an acoustic piano, the strings that are already playing resonate as well. The function that reproduces this effect is called “String Resonance.” 1. Press the [Function] (Exit) button, getting its indicator t ...
-
Roland RG-3M - page 63
61 Chapter 3. Performance ■ Producing the Resonance of the Strings When the Keys Are Played (Damper Resonance) You can change the volume of the damper pedal resonance. On an acoustic piano, depressing the damper pedal makes the notes you play resonate with other strings, adding rich reverberations and fatness to the sound. The damper pedal on the ...
-
Roland RG-3M - page 64
62 Chapter 3. Performance ■ Adjusting the Sound to Achieve the Preferred Tone Quality (Equalizer) The RG-3M features a built-in, three-band digital equalizer. An equalizer boosts or cuts specific sound pitches (frequency ranges) to adjust the sound balance for the overall performance. For example, you can boost the highs to get a crisper sound, o ...
-
Roland RG-3M - page 65
63 Chapter 3. Performance Changing the Pitch of the Keyboard Sound (Transpose) By using the “Transpose function,” you can transpose your performance without changing the notes you play. For example, even if the song is in a difficult key with numerous sharps ( ) or flats ( ), you can transpose it to a key that is easier for you to play. When ac ...
-
Roland RG-3M - page 66
64 Chapter 3. Performance Separately Transposing the Keyboard Sounds and the Song Being Played Back You can transpose the keyboard sounds separately from the song being played back by setting Link to “Off.” To accomplish this, carry out Steps 3–6 in the procedure described on p. 63. 3. Press the [Song] (Select -) button or [ ] (Select +) butt ...
-
Roland RG-3M - page 67
65 Chapter 3. Performance Tuning to Other Instruments’ Pitches (Master Tuning) In situations such as when playing ensemble with other instruments, you can tune the RG-3M’s standard pitch to the pitch of another instrument. The standard pitch generally refers to the pitch of the note that’s played when you finger the middle A key. This tuning ...
-
Roland RG-3M - page 68
66 Chapter 3. Performance Setting the Tuning Curve (Stretched Tuning) Pianos are generally tuned so that the low range is flatter and the high range is sharper than equal tempered pitches. This method of tuning is unique to the piano, and is known as “stretched tuning.” A graph that shows the changes in pitch of actual tuning compared with the ...
-
Roland RG-3M - page 69
67 Chapter 3. Performance Changing the Tuning You can play classical styles such as Baroque using historic temperaments (tuning methods). Most modern songs are composed for and played in equal temperament, the most common tuning in use today. But at one time, there were a wide variety of other tuning systems in existence. By playing in the temperam ...
-
Roland RG-3M - page 70
68 Chapter 3. Performance When playing with tuning other than equal temperament, you need to specify the tonic note for tuning the song to be performed (that is, the note that corresponds to C for a major key or to A for a minor key). 5. Press the [Function] (Exit) button so the indicator goes out. ■ Setting the Tonic When playing with tuning oth ...
-
Roland RG-3M - page 71
69 Chapter 3. Performance Playing Different Tones with the Left and Right Hands (Split Performance) Dividing the keyboard into right-hand and left-hand areas, then playing different sounds in each is called “Split performance.” The boundary key is called the “split point.” The split point key is included in the left-hand keyboard area. Each ...
-
Roland RG-3M - page 72
70 Chapter 3. Performance ■ Changing the Keyboard’s Split Point You can change the location where the keyboard is divided (the split point). 1. Press the [Function] (Exit) button, getting its indicator to light. 2. Press the [Song] (Select -) button or [ ] (Select +) button to display the SPLIT screen. fig.03-301d 3. Press the [Song] (Select -) ...
-
Roland RG-3M - page 73
71 Chapter 3. Performance Adding Reverberation to the Sound ( Reverb) Apply a reverb effect to the notes you play with the RG-3M. Reverb makes it sound as if you are playing in a concert hall. 1. Press the [Function] (Exit) button so the indicator is lit. 2. Press the [Song] (Select -) button or [ ] (Select +) button to display the EFFECT screen. f ...
-
Roland RG-3M - page 74
72 Chapter 3. Performance Assigning Functions to Pedals You can assign a variety of functions to the left and center pedals. You can call up the assigned functions just by pressing the corresponding pedal. 1. Press the [Function] (Exit) button so the indicator is lit. 2. Press the [Song] (Select -) button or [ ] (Select +) button to display the PED ...
-
Roland RG-3M - page 75
73 Chapter 3. Performance 5. Press the [Function] (Exit) button so the indicator goes out. Octave When you play a key while pressing on the pedal, the note for the key being pressed and the note one octave above it are lay- ered and played together. You can adjust the volume of the sound one octave above the layer tone by changing the pressure used ...
-
Roland RG-3M - page 76
74 Chapter 3. Performance Changing the Volume Balance of the Accompaniment and the Keyboard You can also change the balance in the volume of songs or accompaniment and the volume of the keyboard as you play. 1. Press the [Function] (Exit) button so the indicator is lit. 2. Press the [Song] (Select -) button or [ ] (Select +) button to display the B ...
-
Roland RG-3M - page 77
75 Chapter 3. Performance Remembering the Settings Even When the Power is Turned Off ( Memory Backup) Normally, the various settings revert to their default values when the power is turned off. However, you can specify that the settings will be remembered even when the power is turned off. This function is called “Memory Backup.” 1. Press the [ ...
-
Roland RG-3M - page 78
76 Chapter 3. Performance Restoring the Factory Settings ( Factory Reset) You can return the content stored with “Memory Backup” (refer to the previous page) to their original factory settings. This operation is referred to as “Factory Reset.” 1. Press the [Function] (Exit) button so the indicator is lit. 2. Press the [Song] (Select -) butt ...
-
Roland RG-3M - page 79
77 Chapter 4. Recording the Performance ■ Notes Regarding Recording You can store your recorded performances to the “Favorites” (p. 25). If not first saved to the “Favorites,” recorded performances are erased when the RG-3M’s power is turned off. If you want to retain such performances, be sure to save them to the “Favorites.” In ad ...
-
Roland RG-3M - page 80
78 Chapter 4. Recording the Performance Stopping Recording 6. Press the [Moving Key] (Enter) button. Recording stops. The following screen appears. fig.04-040d ■ Play Back the Recorded Performance 1. Press the [ ] button. You will hear the recorded performance. Once again press the [ ] button, and playback will stop. You can save recordings or yo ...
-
Roland RG-3M - page 81
79 Chapter 4. Recording the Performance Saving Recorded Performances If not first saved to the “Favorites” in the RG-3M’s memory or to USB memory, recorded performances are erased when the RG-3M’s power is turned off. If you want to retain such performances, be sure to save them to the “Favorites” or to USB memory. 1. Press the [Functio ...
-
Roland RG-3M - page 82
80 Chapter 4. Recording the Performance 7. Press the [Song] (Select -) button or [ ] (Select +) button to get “save-destination number” to flash. fig.04-090d 8. Press the [ ] (Value -) button or [ ] (Value +) button to select the “save-destination number.” When a performance has already been saved to a number, the name of the performance is ...
-
Roland RG-3M - page 83
81 Chapter 5. User Program Registration You can register the currently selected tone buttons, transposition and volume balance, and a variety of other settings as “favorite performance settings” (User Program). This allows you to call up the registered favorite performance settings whenever you need them. Registering the settings you often use ...
-
Roland RG-3M - page 84
82 Chapter 5. User Program Registration Saving Performance Settings ( User Program) You can register up to 36 User Programs to the RG-3M. 1. Set the Tone, and other data until the settings are the way you want them. 2. Press the [Function] (Exit) button, getting its indicator to light. 3. Press the [Song] (Select -) button or [ ] (Select +) button ...
-
Roland RG-3M - page 85
83 Chapter 5. User Program Registration Calling Up Saved User Programs You can easily call up User Programs. 1. Hold down the [Function] (Exit) button and press the [ ] (Value -) button or [ ] (Value +) button to select the User Program you want to call up. fig.05-070d The display changes to indicate the registered buttons and other performance set ...
-
Roland RG-3M - page 86
84 Chapter 5. User Program Registration Saving the User Program Sets The 36 separate configurations of User Programs registered in the RG-3M can be saved as sets in User Memory (p. 25) or to USB memory. * When saving the settings to USB memory, connect the USB memory to the Ext Memory port (p. 22). 1. Press the [Function] (Exit) button, getting its ...
-
Roland RG-3M - page 87
85 Chapter 5. User Program Registration 7. Press the [Song] (Select -) button or [ ] (Select +) button so that the save-destination number is flashing. fig.05-140d 8. Press the [ ] (Value -) button or [ ] (Value +) button to select the save-destination number. Value: 1–99 To return to the original screen without saving the User Program Set, press ...
-
Roland RG-3M - page 88
86 Chapter 5. User Program Registration Loading Saved User Program Sets You can load sets of User Programs saved in User Memory (p. 25) or to USB memory individually to the RG-3M. * When loading User Programs from USB memory, connect the USB memory to the Ext Memory port (p. 22). 1. Press the [Function] (Exit) button, getting its indicator to light ...
-
Roland RG-3M - page 89
87 Chapter 5. User Program Registration 7. Press the [Moving Key] (Enter) button. 8. Press the [Song] (Select -) button or [ ] (Select +) button so that the User Program Set number is flashing. fig.05-210d 9. Press the [ ] (Value -) button or [ ] (Value +) button to select the number of the User Program Set to be loaded. 10. Press the [Moving Key] ...
-
Roland RG-3M - page 90
88 Chapter 5. User Program Registration Deleting Saved User Program Sets You can delete individual User Program Sets saved to USB memory or in User Memory (p. 25). * When deleting User Programs from USB memory, connect the USB memory to the Ext Memory port (p. 22). 1. Press the [Function] (Exit) button, getting its indicator to light. 2. Press the ...
-
Roland RG-3M - page 91
89 Chapter 5. User Program Registration 7. Press the [Song] (Select -) button or [ ] (Select +) button so that the User Program Set number is flashing. fig.05-270d 8. Press the [ ] (Value -) button or [ ] (Value +) button to select the number of the User Program Set to be deleted. 9. Press the [Moving Key] (Enter) button. A confirmation message app ...
-
Roland RG-3M - page 92
90 Chapter 5. User Program Registration Using the Pedal to Switch User Programs You can use the Pedal as a dedicated switch for selecting User Programs in order. The User Programs are switched each time the pedal is pressed. Each press of the pedal takes you to the next higher numbered User Program until you reach number 36, whereby pressing the pe ...
-
Roland RG-3M - page 93
91 Chapter 6. Changing Various Settings Preventing Changes to the Current Settings (Panel Lock) When “Panel Lock” is activated, all buttons will no longer function. Thus, even if you press a button by mistake, the settings remain unchanged. Making the Setting 1. Set the desired tones and other settings. 2. Hold down the [Function] (Exit) button ...
-
Roland RG-3M - page 94
92 Chapter 6. Changing Various Settings Making other settings You can set the master tuning, temperament, and other settings that make the RG-3M easier to play. The screen in which the settings are changed is called the “Function screen.” You can make the following settings. For all items in the Function screen, refer to (p. 114). Changing the ...
-
Roland RG-3M - page 95
93 Chapter 6. Changing Various Settings Changing the Remote Control Settings ■ Disabling Use of the Remote Control You can prevent the included remote control from controlling the RG-3M by turning the Remote Control function off. This prevents settings from being altered inadvertently if any buttons on the remote control are pressed by mistake. ? ...
-
Roland RG-3M - page 96
94 Chapter 6. Changing Various Settings Functions Assigned to the TRANSPOSE [-] and [+] Buttons 5. Press the [Function] (Exit) button so the indicator goes out. Changing the CD Settings ■ Adjusting CD and Audio File Levels Use this procedure to adjust the volume level of the CD or audio file when playing back a CD or audio file. → You can use t ...
-
Roland RG-3M - page 97
95 Chapter 6. Changing Various Settings ■ Synchronizing the Timing of the Piano and Accompaniment With certain CDs designed to be used with the player function, the timing of the piano and accompaniment sounds may not be synchronized. However, you can synchronize the piano and accompaniment. 1. Press the [Function] (Exit) button, getting its indi ...
-
Roland RG-3M - page 98
96 Chapter 6. Changing Various Settings ■ Enjoying Karaoke with Commercial CDs (Center Cancel) You can minimize the vocal portions of commercial audio CDs or audio files and sing these parts yourself. This is a handy way to enjoy karaoke and practice your singing with your favorite audio CDs or audio files. NOTE You may find that using Center Can ...
-
Roland RG-3M - page 99
97 Chapter 6. Changing Various Settings Initializing the User Memory and USB Memory You can delete all of the data in the User memory, in USB memory, and restore (initialize) the data to the original default factory settings. The RG-3M contains an internal memory area to which you can save recorded performances and other data. This area is called t ...
-
Roland RG-3M - page 100
98 Chapter 6. Changing Various Settings Using the V-LINK Function Connecting the RG-3M to a V-LINK compatible image device allows you to control the images with the RG-3M. What is V-LINK? V-LINK ( ) is a function that allows music and images to be performed together. By using MIDI to connect two or more V-LINK compatible devices, you can easily enj ...
-
Roland RG-3M - page 101
99 Chapter 6. Changing Various Settings Muting or Reducing the Volume of a Specific Part (Minus One/Guide) You can temporarily mute any specific part. This temporary muting of a specified part is called “Minus One.” You can also set a specific part to play at a lower volume. This allows you to use the sound of that part as a “guide” for you ...
-
Roland RG-3M - page 102
100 Chapter 6. Changing Various Settings Changing the Notation Display Settings When displaying notations on a connected external display or television, you can change the parts that appear in the notation and the way the score is displayed. 1. Press the [Function] (Exit) button, getting its indicator to light. 2. Press the [Song] (Select -) button ...
-
Roland RG-3M - page 103
101 Chapter 6. Changing Various Settings Setting the Part to Which Harmonies Are Added (Harmony Part) When “Data” is selected as the Harmony type and you sing along with the playback of the music data, harmonies consistent with the scale of the specified part are added (p. 40). Use the following procedure to set the part to which harmonies are ...
-
Roland RG-3M - page 104
102 Chapter 6. Changing Various Settings Changing the Infrared Transmission Function Settings Some digital devices equipped with an IrDA (infrared) port are able to transfer song data in SMF format to the RG-3M. For more detailed information, refer to the owner’s manual for the digital device. NOTE Users are responsible for learning how to use in ...
-
Roland RG-3M - page 105
103 Chapter 7. Connecting External Devices Connecting to Audio Equipment You can connect audio devices to play the sound of the RG- 3M through the speakers of your audio system, or to record your performance on a recording device. ■ Connectors fig.07-010 Output Jacks You can connect audio equipment using audio cables (sold separately) and play th ...
-
Roland RG-3M - page 106
104 Chapter 7. Connecting External Devices fig.07-030 1. Turn the volume all the way down on the RG-3M and on the device you’re about to connect. 2. Turn off the power to the RG-3M and other connected equipment. 3. Use audio cables (sold separately) to make the connection. 4. Turn on the connected equipment. 5. Turn on the RG-3M. 6. Adjust the vo ...
-
Roland RG-3M - page 107
105 Chapter 7. Connecting External Devices ■ Setup Examples With AUX OUTPUT Set to “Surround” The piano sound is played through the RG-3M’s speakers, and the surround sound is played through the external speakers. Spacious Location Location Limited in Space Connecting MIDI Devices By connecting an external MIDI device and exchanging perform ...
-
Roland RG-3M - page 108
106 Chapter 7. Connecting External Devices 2. Switch off the power to the RG-3M and the device you’re about to connect. 3. Use a MIDI cable (sold separately) to connect the MIDI connectors to each other. Please refer to the connection examples below. 4. Switch on the power to the RG-3M and the connected device. 5. Adjust the volume level on the R ...
-
Roland RG-3M - page 109
107 Chapter 7. Connecting External Devices ■ Disconnecting the Internal Sound Generator and Keyboard (Local Control) When connecting a MIDI sequencer, set Local Control to “OFF.” The setting is at “Local Control ON” when the RG- 3M is powered up. As illustrated, information describing what has been played on the keyboard is passed to the ...
-
Roland RG-3M - page 110
108 Chapter 7. Connecting External Devices ■ Sending Tone Change Messages (Program Change/Bank Select MSB/Bank Select LSB) A Program Change is a message that means “change to the Tone of the specified number.” The device that receives this changes to the Tone of the corresponding number. When you choose a Program Change message (Program Numbe ...
-
Roland RG-3M - page 111
109 Chapter 7. Connecting External Devices 5. Press the [Function] (Exit) button so the indicator goes out. If you wish to save the performance recorded on the RG-3M, use the following procedure. In this situation, your external sequencer is set its MIDI Thru feature to be OFF. For details, refer to the owner’s manual of your MIDI sequencer. 1. C ...
-
Roland RG-3M - page 112
110 Chapter 7. Connecting External Devices If connection to your computer is unsuccessful... Normally, you don’t need to install a driver in order to connect the RG-3M to your computer. However, if some problem occurs, or if the performance is poor, using the Roland original driver may solve the problem. For details on downloading and installing ...
-
Roland RG-3M - page 113
111 Appendices Troubleshooting Case Cause/Remedy The power doesn’t come on Is the power cord connected and plugged in correctly? (p. 19) Depressing a pedal has no effect, or the pedal effect doesn’t stop Is the pedal connected correctly? Make sure the pedal cord is securely connected to the pedal connector (p. 19). Has a different function been ...
-
Roland RG-3M - page 114
112 Troubleshooting In the upper range, the sound changes abruptly beyond a certain key On an acoustic piano, notes in the upper one and a half octaves of the keyboard continue to sound until they decay naturally, regardless of the damper pedal. There is a difference in the timbre as well. Roland pianos faithfully simulate such characteris- tics of ...
-
Roland RG-3M - page 115
113 Error Messages Indication Meaning Error 01: You can only read the music file. It can not be saved. Error 02: An error occurred during writing. The storage media’s protect tab may be in the “Protect” (writing prohib- ited) position, or the storage media may not yet be initialized. Error 10: No storage media is inserted. Insert the storage ...
-
Roland RG-3M - page 116
114 Function Screens No. Function Screen Page 1 Key Touch, Hammer Response p. 57 2 Response p. 58 3 Equalizer p. 62 4 Master Tuning, Temperament p. 65 5 Reverb p. 71 6 Volume Balance p. 74 7 Split Performance p. 69 8 Transpose p. 63 9 Functions to Pedals p. 72 10 Play Mode p. 99 11 Recording p. 77 12 CD / Audio Settings p. 94 13 CD Settings p. 95 1 ...
-
Roland RG-3M - page 117
115 Tone List fig.08-010 Piano 1 1 Superior Grand 2 Superior Grand + Str 3 Superior Grand + Pad 4 Piano + FM E.Piano Piano 2 1 Natural Grand 2 Natural Grand + Str 3 Natural Grand + Pad 4 Piano + Bell Harpsichord 1 Harpsichord 2 Coupled Harpsichord 3 Harpsichord + Choir 4 Harpsichord + Str Vibraphone 1 Vibraphone 2 Bell 3 Harp 4 Electric Piano + Pad ...
-
Roland RG-3M - page 118
116 Internal Song List 981a * All rights reserved. Unauthorized use of this material for purposes other than private, personal enjoyment is a violation of applicable laws. * No data for the music that is played will be output from MIDI Out connector. Jazz Trio Grande Scrambled Egg Blue Sky Rag One Down And Easy Bop On The Rock Fly Free Late Night C ...
-
Roland RG-3M - page 119
117 Parameters Stored to Internal Memory ■ Parameters Stored in Memory Backup ■ Parameters Stored in the User Program Screen Display Description Page KEY TOUCH Touch Key Touch p. 57 Hammer Hummer Response p. 58 RESONANCE KeyOff Key Off Resonance p. 59 String String Resonance p. 60 Damper Damper Resonance p. 61 EQUALIZER Master Master Level p. 6 ...
-
Roland RG-3M - page 120
118 Music Files That the RG-3M Can Use What Are Music Files? Music files contains musical information such as how long the key for a corresponding pitch is played, the force applied to the key played, and other such information. Performance data is transmitted to the RG-3M from music files saved in USB memory and played back without change as songs ...
-
Roland RG-3M - page 121
119 MIDI Implementation Chart Function... Basic Channel Mode Note Number : Velocity After Touch Pitch Bend Control Change Prog Change System Exclusive System Common System Real Time Aux Message Notes Transmitted Recognized Remarks Default Changed Default Messages Altered True Voice Note ON Note OFF Key’s Ch’s 0, 32 1 5 6, 38 7 10 11 64 65 66 67 ...
-
Roland RG-3M - page 122
120 Main Specifications RG-3M <Keyboard> Keyboard 88 keys (PHA II ivory feel Keyboard with Escapement) Touch Sensitivity Touch: 100 levels Hammer Response: Light, Medium, Heavy, Off Keyboard Mode Whole, Layer (as layer tones, volume balance adjustable), Split (split point adjustable) Moving Key Yes <Sound Generator> GM2 system, GS forma ...
-
Roland RG-3M - page 123
121 Main Specifications 962a * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. Display 20 characters, 2 lines LCD External Display VGA, NTSC, PAL Song Select, Slide Show, Lyrics, DigiScore Controls Volume, Brilliance, LCD Contrast, Mic Volume Pedals Damper (half-p ...
-
Roland RG-3M - page 124
122 Index A AC Inlet ..................................................................... 16, 19 Access Indicator ............................................................. 17 All Song .......................................................................... 27 Arabic ............................................................................ ...
-
Roland RG-3M - page 125
123 Index G General MIDI ............................................................... 118 General MIDI 2 ............................................................ 118 Generic .......................................................................... 110 GS Format ..................................................................... 118 Guide ...
-
Roland RG-3M - page 126
124 Index O Octave ............................................................................. 73 One Song ........................................................................ 27 Original ......................................................................... 110 Output Jacks ................................................................. ...
-
Roland RG-3M - page 127
125 Index USER PROGRAM Screen ............... 82, 84, 86, 88, 90 VOCAL Screen ................................................... 40–41 Slide Interval .................................................................. 51 Slide Show .......................................................... 50–51, 98 SMF Music Files ............................. ...
-
Roland RG-3M - page 128
126 MEMO RG-3M_e3.book 126 ページ ２００８年３月２５日 火曜日 午前１０時１分 ...
-
Roland RG-3M - page 129
As of Oct. 1, 2007 (ROLAND) Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. EGYPT Al Fanny Trading Office 9, EBN Hagar Al Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: (022)-418-5531 REUNION Maison FO - YAM Marcel 25 Rue Jules Herm ...
-
Roland RG-3M - page 130
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For EU Countries For Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouill ...
-
Roland RG-3M - page 131
...
-
Roland RG-3M - page 132
04567423 08-04-3N * 04567423 - 03 * ...
Do you have a question concerning Roland RG-3M?
Use the form below
If you did not solve your problem by using a manual Roland RG-3M, ask a question using the form below. If a user had a similar problem with Roland RG-3M it is likely that he will want to share the way to solve it.