English dropdown-ico

Manual Sharp PN-V601A

42 pages Not applicable
Download

Go to site of 42

Summary
  • Sharp PN-V601A - page 1

    PN-V601A LCD MONIT OR OPERA TION MANUAL ...

  • Sharp PN-V601A - page 2

    2 E This guide contains instructions regarding operation, settings, and similar details. For instructions regarding connection and installation, refer to the included Operation Manual. Manual Scope - Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation. - HDMI, the HDMI Logo and High-Denition Multimedia Int ...

  • Sharp PN-V601A - page 3

    3 E n Front view 1 23 45 6 7 8 9 The rear buttons if seen from the front 1. LCD panel 2. INPUT button 3. MENU button 4. VOL -/Cursor control ( ) button 5. VOL +/Cursor control ( ) button 6. BRIGHT -/Cursor control ( ) button 7. BRIGHT +/Cursor control ( ) button 8. Power button 9. Power LED Part Names n Rear view When the PN-ZB02 (optional) is atta ...

  • Sharp PN-V601A - page 4

    E 4 Part Names n Remote control unit (Supplied with the PN-ZR01 (optional)) 1 2 3 4 5 6 7 12 9 10 11 8 1. Signal transmitter 2. POWER button 3. MUTE button 4. VOL +/Cursor control ( ) button 5. BRIGHT -/Cursor control ( ) button 6. DISPLA Y button 7. MODE button 8. INPUT button 9. MENU button 10. BRIGHT +/Cursor control ( ) button 1 1. VOL -/Cur ...

  • Sharp PN-V601A - page 5

    5 E Basic Operation When performing operation of multiple monitors with the remote control unit, rst set the remote control unit to the appropriate remote control mode (see page 7). 1 2 3 4 5 6 7 8 TIPS • Y ou can perform operation of the monitor with the rear buttons. Utilize the buttons belonging to the monitor that you would like to operate ...

  • Sharp PN-V601A - page 6

    E 6 Basic Operation n Switching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE PC input Displays image so it lls the entire screen. A V input An image with a 4:3 aspect ratio is stretched to ll the entire screen. ZOOM 1 PC input An image with a 4:3 aspect ratio is enla ...

  • Sharp PN-V601A - page 7

    7 E Remote Control Mode With the remote control unit it’s possible to perform operation of... • The primary monitor • Monitors with a specied ID No. • All primary/secondary monitors It’s necessary to specify which type of operation will be performed in advance. 1. If using the remote control unit, press MODE for approx 5 seconds. If us ...

  • Sharp PN-V601A - page 8

    8 E Menu Items Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 9 to 12 for details of each menu items. Caution • Do not turn the main power switch off while the menu items are being displayed. Doing so may initialize the settings. n Ex ...

  • Sharp PN-V601A - page 9

    E 9 Menu item details The menu will differ depending on the input mode. n SCREEN AUTO (PC D-SUB/PC RGB) The CLOCK, PHASE, H-POS, and V -POS are automatically adjusted. Pressing performs adjustment. Use this automatic adjustment when you use the PC D-sub input terminal or PC RGB input terminals to display a PC screen for the rst time or when you ...

  • Sharp PN-V601A - page 10

    E 10 n AUDIO TREBLE Adjusts the volume of treble-level sound. BASS Adjusts the volume of bass-level sound. BALANCE Adjusts the balance of the audio sound between right and left. RESET Resets the values of the AUDIO menu items to the factory preset values. Select “ON” and then press MENU . n SETUP OSD H-POSITION Adjusts the horizontal display po ...

  • Sharp PN-V601A - page 11

    E 11 Menu Items POWER MANAGEMENT POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal standby mode. COLOR SYSTEM (A V S-VIDEO/A V VIDEO) Select the color system of the A V equipment which is connected to A V S-video and A V video input terminal. (AUTO / P AL / P AL-60 / SECAM / NTSC3.58 / NTSC4.43) When AUTO ...

  • Sharp PN-V601A - page 12

    E 12 Menu Items n MUL TI ENLARGE (See page 13.) Sets whether or not to use the enlarge function. ADV ANCED (ENLARGE) ENLARGE H / ENLARGE V ......... Sets the number of screen splits (number of monitors) in the horizontal/vertical direction used for the enlargement. ENLARGE-POS ......... Specify the split screen to be displayed when the enlargement ...

  • Sharp PN-V601A - page 13

    E 13 Menu Items n Enlarge • Y ou can align several monitors and integrate them into a single large screen to display . • Up to ve monitors can be aligned in both the horizontal and vertical directions. • Each monitor displays enlarg ed views of separated images. (Example) Horizontal direction: 2 monitors Ve rtical direction: 2 monitors Hor ...

  • Sharp PN-V601A - page 14

    E 14 n SCHEDULE Y ou can set the time to switch the monitor on and off. Set th is funct ion with “SCHEDU LE” in t he OPTIO N menu. (See page 1 1.) SCHEDULE No. POWER DA Y OF THE WEEK TIME INPU T XXXX/XX/XX XXX XX:XX:XX (2) OK … [MENU] 1366x768 V: 60 Hz H: 47.7 kHz (1) (3) (4) (5) PC D-SUB 1. Press or to select the SCHEDULE number , and press ...

  • Sharp PN-V601A - page 15

    E 15 n ADV ANCED items (A V input) (See page 9 for additional Menu item details.) FLESH TONE Adjust the hue control. 3D-NR Reduce the noise of playback images on video. Setting a higher level reduces more noise. However , it may cause blurring on an image. MPEG-NR Reduce block noise caused by digital compression. 3D-Y/C (A V VIDEO) Specify whether ...

  • Sharp PN-V601A - page 16

    16 E Y ou can return the settings to their factory-preset values and restrict operations. 1. If using the remote control unit, press SIZE until “F” is displayed in the upper left area of the screen, then while “F” is being displayed, press , , , and in that order . If using the monitor buttons, press and at the same time until “F” is di ...

  • Sharp PN-V601A - page 17

    17 E Controlling the Monitor with a PC (RS-232C) Y ou can control this monitor from a PC via RS-232C (COM port) on the PC. Y ou can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 18), you can make input mode selection/adjustment or can check the status of a specic monitor . Preca ...

  • Sharp PN-V601A - page 18

    E 18 Controlling the Monitor with a PC (RS-232C) n Response code format When a command has been executed correctly O K Return code (0D H , 0A H ) A response is returned after a command is executed. * If an ID number has been assigned O K SPC 0 0 1 ID number of respondin g monitor Space (20 H ) Return code (0D H , 0A H ) When a command has not been ...

  • Sharp PN-V601A - page 19

    E 19 Controlling the Monitor with a PC (RS-232C) n Commands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST ......... A monitor receiving this command sets its own ID number in the parameter eld. Example: IDST0001 OK 001 ← The ...

  • Sharp PN-V601A - page 20

    E 20 Controlling the Monitor with a PC (RS-232C) n Repeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. Y ou can use Repeater control function without assigning ID numbers. [E xamp l e ] Set 1 Set 2 Set 3S et 4 * If monitors are ...

  • Sharp PN-V601A - page 21

    E 21 RS-232C command table How to read the command table Command: Command eld (See page 17.) Direction: W When the “Parameter” is set in the parameter eld (see page 17), the command functions as described under “Control/Response Contents”. R The returned value indicated under “Reply” can be obtained by setting “????”, “ ?” ...

  • Sharp PN-V601A - page 22

    E 22 PICTURE menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) AUTO AGIN W 1 When the input mode is PC D-SUB, PC RGB. - ○ ○ CONTRAST CONT WR 0-60 0-60 0-127 on PC D-SUB, PC RGB. ○ BLACK LEVEL BL VL WR 0-60 0-60 0-127 on PC D-SUB, PC RGB. TINT TINT WR 0-60 0-60 COLORS COLR WR 0-60 0-60 SHARPNESS SHRP WR 0- ...

  • Sharp PN-V601A - page 23

    E 23 SETUP menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) OSD H-POSITION OSDH WR 0-100 0-100 ○ ○ ○ OSD V -POSITION OSDV WR 0-100 0-100 SCREEN MOTION SCSV WR 0-4 0-4 0: OFF , 1-4: P A TTERN1-4 ○ MOTION TIME 1 MTIM WR 0-20 0-20 ○ MOTION TIME 2 P A TTERN1 MINT WR 10-990 10-990 Per 10 seconds ○ P A T ...

  • Sharp PN-V601A - page 24

    E 24 OPTION menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) DA TE/TIME SETTING DA TE WR AABBCCDDEE AABBCCDDEE AA: Y ear, BB: Month, CC: Day , DD: T ime, EE: Minute ○ ○ ○ SCHEDULE SC01- SC08 WR ABCDEFFGGH ABCDEFFGGH Schedule of a specied number A: Schedule 0= Not effective, 1 = Effective B: Power 0 = ...

  • Sharp PN-V601A - page 25

    E 25 Controlling the Monitor with a PC (RS-232C) MUL TI menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) ENLARGE ENLG WR 0-1 0-1 0: OFF , 1: ON - ○ ○ ENLARGE MODE EMAG WR 0-4 0-4 0: OFF , 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5 EMHV WR 1 1-55 1 1-55 1 x 1 (OFF) to 5 x 5 (“m x n” is expressed as “mn” ...

  • Sharp PN-V601A - page 26

    E 26 PIP/PbyP menu Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) PIP MODES MWIN WR 0-3 0-3 0: OFF , 1: PIP , 2: PbyP , 3: PbyP2 ○ ○ ○ PIP SIZE MPSZ WR 1-12 1-12 ○ PIP POS THE LONGEST DIRECTION MHPS W 0-100 ○ R 0-100 ○ THE SHORTEST DIRECTION MVPS W 0-100 ○ R 0-100 ○ PIP POS LD+SD BA TCH MPOS W 0-1 ...

  • Sharp PN-V601A - page 27

    E 27 Others Function Command Direction Parameter Reply Control/Response contents *1 *2 (A) (B) SCREEN SIZE (PC) WIDE WR 1-5 1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2 ○ ○ ○ SCREEN SIZE (A V) WIDE WR 1-5 1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot ○ VOLUME VOLM WR 0-31 0-31 ○ MUTE MUTE WR 0-1 0-1 0: OFF , 1: ON ...

  • Sharp PN-V601A - page 28

    28 E When the PN-ZB02 (optional) is attached, your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. Y ou can also congure the monitor to send e-mail notication when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through). Hub LAN terminal LAN cabl ...

  • Sharp PN-V601A - page 29

    29 E 29 ■T osetfromaPC When the monitor is connected to a PC, LAN settings can be congured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC’s IP address (3) Congure the monitor ’s LAN settings (1) Connecting your monitor to a PC Connect a commercially available crossover LAN cable (UPT cable, Cat ...

  • Sharp PN-V601A - page 30

    30 E 30 5. Click on “LAN SETUP” under NETWORK. 6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically , change this setting to “ON”. T o set the address manually , set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set to “OFF”, specify an IP ...

  • Sharp PN-V601A - page 31

    31 E 31 ■INFORMA TION Information about this monitor appears. ■CONTROL Y ou can control the operations corresponding to the buttons ( POWER INPUT SIZE ) on the remote control unit. (See page 5.) TIPS • In standby mode, Power ON is the operation available. ■ ADJUSTMENT Y ou can adjust these settings which are also available on the m ...

  • Sharp PN-V601A - page 32

    32 E 32 ■NETWORK(LANSETUP) This screen allows you to set the settings necessary when the monitor is connected to a LAN. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically , change this setting to “ON”. T o set the address manually , set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set to ...

  • Sharp PN-V601A - page 33

    33 E 33 ■NETWORK(GENERAL) This screen allows you to specify the general LAN settings. MONITOR NAME Specify a name for this monitor as it should appear on the Internet Explorer screen. AUTO LOGOUT TIME Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network. Specify in minutes from 1 to 65535. ...

  • Sharp PN-V601A - page 34

    34 E 34 ■MAIL(RECIPIENT) This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error . RECIPIENT E-MAIL ADDRESSES Specify the e-mail addresses to send error notication e-mail to. CONDITION Specify the conditions to send mails. When you check PERIODICAL, specify the date and time to ...

  • Sharp PN-V601A - page 35

    35 E 35 Controlling the Monitor with a PC (LAN) ■SNMP Y ou can congure settings related to SNMP . SNMP SETTING Set whether to enable or disable SNMP . VERSION Set the version of the SNMP to be supported. COMMUNITY NAME 1 to 3 Set the name of the community required for the access. USER 1 to 3 Set the user name, password, authentication metho ...

  • Sharp PN-V601A - page 36

    36 E T roubleshooting If you are experiencing any problem with your display , before calling for service, please review the following troubleshooting tips. There is no picture or sound. • Is the power cord disconnected? • Is the main power switch off? • Is the monitor in standby mode (the power LED illuminating in orange)? • Make sure corre ...

  • Sharp PN-V601A - page 37

    37 E Specications n PN-V601A Product Specications Model PN-V601A LCD component 60" Class [60 inch (152.4cm) diagonal] TFT LCD Max. resolution (pixels) 1366 x 768 Max. colors Approx. 16.77 M colors Pixel pitch 0.973 mm (H) × 0.973 mm (V) Viewing angle 176° right/left/up/down (contrast ratio ≥ 10) Screen active area inch (mm) 52-5/8 x ...

  • Sharp PN-V601A - page 38

    38 E Specications n Dimensional Drawings Note that the values shown are approximate values. Unit: inch [mm] 52-5/8 [1335.9] Opening width (52-5/16 [1329.4]) Opening height (29-7/16 [747.7]) 29-1 1/16 [754.2] 7-7/8 [200] 5-7/8 [149.3] 52-5/8 [1335.9] 3-5/8 [92.3] 7-7/8 [200] 7-7/8 [200] VESA holes * 3-15/16 [100] 3-15/16 [100] When mounting the m ...

  • Sharp PN-V601A - page 39

    39 E n Compatible signal timing (PC) VESA Wide US TEXT Sun Screen resolution Hsync Vsyn c D ot frequency Digital 640 × 480 800 × 600 848 × 480 1024 × 768 1 152 × 864 *1 1280 × 768 1280 × 800 *1 1280 × 960 *1 1280 × 1024 *1 1360 × 768 1400 × 1050 *1 1600 × 1200 *1 1680 × 1050 *1 1280 × 720 1366 × 768 1920 × 1080 *1 720 × 400 1024 × ...

  • Sharp PN-V601A - page 40

    40 E n Compatible signal timing (A V) Screen resolution Frequency DVI-D* 2 HDMI Component* 2 1920 × 1080p * 1 24Hz - Ye s - 50Hz Ye s Ye s Ye s 59.94Hz Ye s Ye s Ye s 60Hz Ye s Ye s Ye s 1920 × 1080i * 1 50Hz Ye s Ye s Ye s 59.94Hz Ye s Ye s Ye s 60Hz Ye s Ye s Ye s 1280 × 720p 50Hz Ye s Ye s Ye s 59.94Hz Ye s Ye s Ye s 60Hz Ye s Ye s Ye s 720 ? ...

  • Sharp PN-V601A - page 41

    41 E Specications n PC/A V DVI-D input terminal pins (DVI-D 24 pin) No. Function No. Function 1 TMDS data 2- 13 N.C. 2 TMDS data 2+ 14 +5V 3 TMDS data 2/4 shield 15 GND 4 N.C. 16 Hot-plug detection 5 N.C. 17 TMDS data 0- 6 DDC clock 18 TMDS data 0+ 7 DDC data 19 TMDS data 0/5 shield 8 N.C. 20 N.C. 9 TMDS data 1- 21 N.C. 10 TMDS data 1+ 22 TMDS c ...

  • Sharp PN-V601A - page 42

    PN-V601A G EN13J(1) ...

Manufacturer Sharp Category Monitor

Documents that we receive from a manufacturer of a Sharp PN-V601A can be divided into several groups. They are, among others:
- Sharp technical drawings
- PN-V601A manuals
- Sharp product data sheets
- information booklets
- or energy labels Sharp PN-V601A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sharp PN-V601A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sharp PN-V601A, service manual, brief instructions and user manuals Sharp PN-V601A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sharp PN-V601A.

Similar manuals

A complete manual for the device Sharp PN-V601A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sharp PN-V601A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sharp PN-V601A.

A complete Sharp manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sharp PN-V601A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sharp PN-V601A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sharp PN-V601A, that we can find in the current document
3. Tips how to use the basic functions of the device Sharp PN-V601A - which should help us in our first steps of using Sharp PN-V601A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sharp PN-V601A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sharp PN-V601A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sharp PN-V601A?

Use the form below

If you did not solve your problem by using a manual Sharp PN-V601A, ask a question using the form below. If a user had a similar problem with Sharp PN-V601A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)