-
Zanussi ZGF 692 - page 1
GAS HOBS ZGF 682 ZGF 692 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB ...
-
Zanussi ZGF 692 - page 2
2 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions S tep by step instructions for an operation Hints and T ip s Environmental Information Import ant Safety Information Y ou MUST read hese warnings carefully before inst alling or using the hob. If you need ass ...
-
Zanussi ZGF 692 - page 3
3 1. Hob T op 2. Auxiliary Burner 3. Semi-rapid Burners 4. Ultra-rapid Triple-crown Burner 5. Control knobs Description of the Hob This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low V ol t ageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 (Gas Appliances) , ...
-
Zanussi ZGF 692 - page 4
4 Hob burners T o light a burner: z turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" and “crown” (see Fig. 1 - letter A and B) are in the ...
-
Zanussi ZGF 692 - page 5
5 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing ...
-
Zanussi ZGF 692 - page 6
6 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or inst allation, a charge will be made even if the appliance is under guarantee. SYM ...
-
Zanussi ZGF 692 - page 7
7 Zanussi Guarantee conditions W e, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour , materials or carriage on conditio ...
-
Zanussi ZGF 692 - page 8
8 Rear Left Burner (semi-rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Lef t Burner (auxiliary) Heat Input 1.0 kW (3412 BTU/HR) Rear Right Burner (semi-rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Right Burner: ( Ultra-rapid T rip le- crown) Heat Input 4.0 kW (13652 BTU/HR) Instructions for the Inst aller Engineers technical dat a Overall dimensions ...
-
Zanussi ZGF 692 - page 9
9 Import ant safety requirement s I CLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE FO 0813 FO 0812 700 mm This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Ed ...
-
Zanussi ZGF 692 - page 10
10 Rectangular cut-out size for hob A) End of shaft with nut B) W asher C) Elbow FO 0814 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper . The connection should be suit able for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a ...
-
Zanussi ZGF 692 - page 11
11 FO 0763 FO 2564 FO 2044 1 2 3 FO 0199 a Fitting the Hob into the worktop ) Carry out the building in of the hob as follows: • place the seals supplied with the hob on the side edges of the cut out and at 8 mm from the front and rear edges, as shown in the diagram, taking care that the seals meet without overlapping; • place the hob in the cu ...
-
Zanussi ZGF 692 - page 12
12 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240 ...
-
Zanussi ZGF 692 - page 13
13 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and a ...
-
Zanussi ZGF 692 - page 14
14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer Light burner manually Check gas supply at burner Check continuity from 'N ...
-
Zanussi ZGF 692 - page 15
15 Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to sui ...
-
Zanussi ZGF 692 - page 16
Grafiche MDM - Forlì 35670-9506 01/05 CUSTOMER CARE Zanussi 55-77 High S treet Slough Berkshire, SL1 1DZ T el: 08705 727727 © Electrolux plc 2003 From the Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux ...
Do you have a question concerning Zanussi ZGF 692?
Use the form below
If you did not solve your problem by using a manual Zanussi ZGF 692, ask a question using the form below. If a user had a similar problem with Zanussi ZGF 692 it is likely that he will want to share the way to solve it.