English dropdown-ico

Manual Smart Technologies 2000i

15 pages 0.86 mb
Download

Go to site of 15

Summary
  • Smart Technologies 2000i - page 1

    99-00496-00 Rev A0 Interactive Whiteboard Projector Replacement Guide for Projector Replacement Kits NEC MT1060R (03-00043) and NEC MT860R (03-00041) 2000i ...

  • Smart Technologies 2000i - page 2

    FCC Warning This equipment has been tested and found to comp ly wi th the limits for a Class A digita l device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial env ir onment. This equipment generates, uses and can radiate rad ...

  • Smart Technologies 2000i - page 3

    99-00496-00 Rev A0 Contents Replacing the Project or in a 2000i ................................................... 1 Aligning the Proj ected Image ........................................................... 6 Customer Support ........................................................................... 11 Contacting SMART Te chnical S upport ....... ...

  • Smart Technologies 2000i - page 4

    ...

  • Smart Technologies 2000i - page 5

    99-00496-00 REV A0 Projector Replacement Guide for the 2000i 1 Replacing the Projector in a 2000i Use these instructions to install a replacem ent NEC MT860 or NEC MT1060 projector in your Rear Projection SMART Board 2000i interactive whiteboard. To remove the original projector 1. Shut down the computer , and then press and hold the Projector Stan ...

  • Smart Technologies 2000i - page 6

    2 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 5. With another person supporting the projector, reach through the view port and remove the three nuts (including the steel and nylon washers) that secure the projector in place and then remove the projector. Use the provided 7/16" nut driver to loosen t he nuts. Keep the nuts and ...

  • Smart Technologies 2000i - page 7

    99-00496-00 REV A0 Projector Replacement Guide for the 2000i 3 6. Set the projector down on a flat surface and remove the projector plate from the projector: Using the provided hex key, loosen and remove the four sets of screws, spacers and washers at the corners of the plate. 7. Transfer the plate to the new projector and attach it using the same ...

  • Smart Technologies 2000i - page 8

    4 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 8. Slide the projector plate back into plac e by maneuvering the screws through the cabinet slots. With a partner supporting the bottom of the projector, use the provided 7/16" nut driver to secure the projector plate in pl ace using the nuts and washers that you removed in step 5. ...

  • Smart Technologies 2000i - page 9

    99-00496-00 REV A0 Projector Replacement Guide for the 2000i 5 9. Connect the video, power and serial cables to the projector, along with any other cables (VCR, external monitor, etc. ) that you removed in step 2. 10. Replace the strap that secures t he projector to the projector plate. 11. Plug the power cord back into the power outlet. 12. Toggle ...

  • Smart Technologies 2000i - page 10

    6 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 Aligning the Projected Image If the projected image is blurry or does not fit the screen, complete the four adjustment procedures that follow. For the first three, (roll, side-to-side and image size adjustment), you must watch the image on the back of the screen while making the adjustm ...

  • Smart Technologies 2000i - page 11

    99-00496-00 REV A0 Projector Replacement Guide for the 2000i 7 To adjust the image laterally 1. Crouch behind the projector and look at the projected image through the view port. 2. Using the supplied 7/16" nut driver, loosen the two nuts on the left side of the projector plate. 3. Slide the projector plate to the right or le ft to adjust the ...

  • Smart Technologies 2000i - page 12

    8 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 To change the image size 1. Crouch behind the projector and look at the projected image through the view port. 2. Loosen the four hex screws that secure the proj ector to the projector plate using the provided 3 mm hex key. NOTE : These screws are located on top of the projecto r plate, ...

  • Smart Technologies 2000i - page 13

    99-00496-00 REV A0 Projector Replacement Guide for the 2000i 9 Screen R emoved for Clarity As you maneuver the hex key through the acce ss holes, watch it from the side to see when it engages with the hex screw. Look here t o see when the he x key engage s with t he scr ew 4. Slide the projector backward or forward to alter the image size. 5. When ...

  • Smart Technologies 2000i - page 14

    10 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 To move the image up or down 1. Crouch down in front of the screen. 2. Look underneath the pen tray and locate the El ectronics Tray. Locate a plastic cap on the right side of the Electronics Tray. Electr oni cs T ray 3. Remove the plastic cap to reveal an access hole. 4. Use the suppl ...

  • Smart Technologies 2000i - page 15

    99-00496-00 REV A0 Projector Replacement Guide for the 2000i 11 Customer Support SMART’s Technical Support team welcomes your call. However, you may want to contact your local reseller first if you experience problems with any SMART product. SMART’s resellers can readily provide you with quick advice so you can enjoy the benefits of your replac ...

Manufacturer Smart Technologies Category Projector Accessories

Documents that we receive from a manufacturer of a Smart Technologies 2000i can be divided into several groups. They are, among others:
- Smart Technologies technical drawings
- 2000i manuals
- Smart Technologies product data sheets
- information booklets
- or energy labels Smart Technologies 2000i
All of them are important, but the most important information from the point of view of use of the device are in the user manual Smart Technologies 2000i.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Smart Technologies 2000i, service manual, brief instructions and user manuals Smart Technologies 2000i. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Smart Technologies 2000i.

Similar manuals

A complete manual for the device Smart Technologies 2000i, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Smart Technologies 2000i by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Smart Technologies 2000i.

A complete Smart Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Smart Technologies 2000i - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Smart Technologies 2000i, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Smart Technologies 2000i, that we can find in the current document
3. Tips how to use the basic functions of the device Smart Technologies 2000i - which should help us in our first steps of using Smart Technologies 2000i
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Smart Technologies 2000i
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Smart Technologies 2000i in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Smart Technologies 2000i?

Use the form below

If you did not solve your problem by using a manual Smart Technologies 2000i, ask a question using the form below. If a user had a similar problem with Smart Technologies 2000i it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)