English dropdown-ico

Manual Kenmore Water System

20 pages 0.84 mb
Download

Go to site of 20

Summary
  • Kenmore Water System - page 1

    INSTALLATION MANUAL For softeners with DELUXE valve designed for plumbing up to 1 inch Caution: Read and Follow All Safety Rules and Operating Instructions Before First Use of This Product. If you have questions when installing, operating or main- taining your softener, and when setting the timer, call this toll-free number... 1-800-426-9345 (M - F ...

  • Kenmore Water System - page 2

    O I 1,1 ,1,I.1,1.I ,1,I.1. This manual gives you the steps needed to install your new Kenmore Water Softener. To better understand how the water softener is installed, and to know what you will need, please read this entire manual before beginning. After you have installed the water softener, the included owner's manual tells you how to start, ...

  • Kenmore Water System - page 3

    _,_i_,_,_,_,_,_,_,_,_i TABLE OFCONTENTS 0 F N i,J J., J,_ ,J J._ J,_f,J J._. i,., j,,J ,., j,,J j,J ,., j,,J. i,_,J.I J,_ h.' J.I. A. Safety Guides B. BEFORE INSTALLING CHECKS & TESTS Unpacking The Water Softener C. Water System Tests PLAN YOUR INSTALLATION A. Where To Install The Water Softener B. Tools, Pipe and Fittings, Other Materials ...

  • Kenmore Water System - page 4

    SECTION 1 BEFORE INSTALLING CHECKS & TESTS S C N i,JJ,aJ.J ,JJ,aJ.J ,JJ,a. t,aJ.J ,aJ.=J,J ,a J.=. i,JJ,a ,JJ,a. t,aJ.= ,aJ.=. i.=.a._._,a i.=.a._._,a i.=.a._. A. SAFETY GUIDES • Read all steps, guides and rules carefully before installing and using your new water softener. Follow all steps exactly to correctly install. Failure to follow them ...

  • Kenmore Water System - page 5

    SECTION 1 BEFORE INSTALLING CHECKS & TESTS B. UNPACKING THE WATER SOFTENER Directions for unpacking the softener are on the top of the shipping carton. This manual, and the own- er's manual, were in the small parts bag. You will need the small parts to install the softener. Keep them in the bag until you are ready to use them so you don&ap ...

  • Kenmore Water System - page 6

    SECTION 1 BEFORE INSTALLING CHECKS & TESTS C. WATER SYSTEM TESTS Has your water supply had a chemical analysis? Please see page A on the inside of the front cover. CHECK YOUR WATER PRESSURE -- For your softener to work right, a water pressure of no lower than 20 pounds per square inch (psi) is needed in the house water pipes. The highest pressu ...

  • Kenmore Water System - page 7

    SECTION 2 PLAN YOUR INSTALLATION S C N i.a.a._,a,_ .a.a._,a,_ .a.a._. ha ,a.l.I J.a ,a .I,a. I..= ..=.a._. ha ,a.l,a. i..,.a.=.i., i..,.a.=.i., i..,.a.=. A. WHERE TO INSTALL THE WATER SOFTENER Think of the following points as [], Do not install in a place where the softener could you choose a place to put your freeze. Damage caused by freezing void ...

  • Kenmore Water System - page 8

    SECTION 2 ,,, I PLAN YOUR INSTALLATION B. TOOLS, PIPE AND FITTINGS, OTHER MATERIALS NEEDED You must first decide how to run in and out pipes to the softener. Look at your house main water pipe at the point you will connect the softener. Is the pipe soldered copper, glued plastic, or threaded galva- nized or brass? What is the pipe size? What kind o ...

  • Kenmore Water System - page 9

    SECTION 2 PLAN YOUR INSTALLATION B. PIPE AND FI'I-rlNGS, PLAN DRAWING _DUR HOUSE MAIN WATER RPE * LEFT RIGHT 120V - 60Hz Electrical F_ Outlet VALVE OUTLET SIDE Draw the plans for your In and OUT piping here. Be sure to follow the guides on page 2-2. Include all pipe, fittings and accesso- ries you will use. Make a list of all materials you wil ...

  • Kenmore Water System - page 10

    SECTION 2 PLAN YOUR INSTALLATION C. TYPICAL SOLDERED COPPER (OR CPVC) IN AND OUT PIPES TO SOFTENER DELUXE VALVE MODELS * 1" NPT X 3/4" Sweat Reducer (2) Outlet SOFTENER Inlet VALVE *NOTE: For 1 in. plumbing _onne_tion, buy 2 sweat adaptors (1 in. female thread x 1 in. sweat) and plumb directly to the inlet- outlet adaptors or by- pass val ...

  • Kenmore Water System - page 11

    SECTION 2 PLAN YOUR INSTALLATION D. TYPICAL THREADED IN AND OUT PIPES TO SOFTENER If you are planning a threaded plumbing installation, with a 3-valve bypass, use the drawing in Fig. 4 as a guide. Use union fittings, as needed, to connect the plumbing. DELUXE VALVE MODELS OUT Outside (Raw Water In) FITTINGS REQUIRED NOT IDENTIFIED 90 ° Elbow (2) U ...

  • Kenmore Water System - page 12

    SECTION 3 STEP BY STEP GUIDES TO INSTALL A. ASSEMBLE INLET-OUTLET ADAPTORS, OR PLASTIC BYPASS VALVE S C N i,JJ,aJ.J ,JJ,aJ.J ,JJ,a. i,a ,aJ.=J,J ,a J.=. i,J J ,JJ,a. i.t .t,_,_. i,aJ ,aJ.=. i.=.a._._,a i.=.a._._,a i.=.a._. [ Close the shut-off valve on the house main water pipe, near the water meter or pres- sure tank, to turn off the wa- ter. []Sh ...

  • Kenmore Water System - page 13

    SECTION 3 STEP BY STEP GUIDES TO INSTALL A. ASSEMBLE INLET-OUTLET ADAPTORS, OR PLASTIC BYPASS VALVE DELUXE VALVE MODELS INSTALLING BYPASS VALVE, and/or INLET and OUTLET COPPER TUBES Before ins'telling the bypass valve, or copper tube, be sure the turbine and support are firmly in place in the valve outlet port. turbine sensor support port ...

  • Kenmore Water System - page 14

    SECTION 3 STEP BY STEP GUIDES TO INSTALL B. INSTALL 3-VALVE BYPASS _l INSTALLING 3 VALVE BYPASS AND PIPES (FIG. 9) O Cut the house main water pipe where you will connect the softener. Loosely put together pipe, fittings, and the 3 valves. Place valve(s) within easy reach. 3 - VALVE BYPASS IMPORTANT: When looking at the front of the softener, the in ...

  • Kenmore Water System - page 15

    SECTION 3 STEP BY STEP GUIDES TO INSTALL C. LOCATE WATER SOFTENER, AND CONNECT PIPES []MOVE THE SOFTENER INTO PLACE Move the softener into place, onto a level and smooth surface. If needed, put a piece of 3/4" plywood, at least 17" x 20", under the tank. Then put spacers under the plywood to level the soft- ener. Do not put shims or ...

  • Kenmore Water System - page 16

    SECTION 3 STEP BY STEP GUIDES TO INSTALL D. CONNECT VALVE AND SALT TANK DRAINS ffi CONNECT THE VALVE DRAIN HOSE • Keep the hose lower than the drain fitting. (In Take a length of 3 / 8" inside diameter drain tub- ing and attach one end to the drain fitting (FIG. 12). Use a tube clamp to hold it in place. Put the other end of the tubing over ...

  • Kenmore Water System - page 17

    SECTION 3 STEP BY STEP GUIDES TO INSTALL D. CONNECT VALVE AND SALT TANK DRAINS []CONNECT SALT TANK OVERFLOW TU- Important: 0 @ O 0 BING Take the rubber grommet, tube adaptor and tube clamp (FIG. 12) that are in the parts bag. Push the grommet into the hole in the salt tank wall so half is inside and half is outside. Push the bigger end of the tube ...

  • Kenmore Water System - page 18

    SECTION 3 STEP BY STEP GUIDES TO INSTALL E. PRESSURE TEST / CHECK FOR LEAKS [] CAUTION: To avoid water or air pressure damage to soft- ener inner parts, and to flush pipe chips or other residue from the water pipes, be sure to do the following steps exactly as instructed. Look at the picture in FIG. 15 showing your kind of bypass valve(s). []Fully ...

  • Kenmore Water System - page 19

    SECTION 3 STEP BY STEP GUIDES TO INSTALL F. GROUNDING / CONNECT TO ELECTRICAL POWER []INSTALL GROUNDING WIRE BETWEEN To restore the ground, take the ground clamp kit THE SOFTENER IN AND OUT PIPES The house cold water pipe (iron or copper) is often used to ground all electrical outlets in the home. Outlets are grounded to protect you from shock when ...

  • Kenmore Water System - page 20

    SECTION 3 STEP BY STEP GUIDES TO INSTALL F. GROUNDING / CONNECT TO ELECTRICAL POWER []PLUG IN THE TRANSFORMER CONNECTING TRANSFORMER Plug the transformer into the electrical outlet. Transformer 120V-6OHz Electrical OuUet Power Cable from Face Plate-_mer After installing your water softener, replace the cov- ers. For the UltraSoft 100, first positio ...

Manufacturer Kenmore Category Water System

Documents that we receive from a manufacturer of a Kenmore Water System can be divided into several groups. They are, among others:
- Kenmore technical drawings
- Water System manuals
- Kenmore product data sheets
- information booklets
- or energy labels Kenmore Water System
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenmore Water System.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenmore Water System, service manual, brief instructions and user manuals Kenmore Water System. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenmore Water System.

Similar manuals

A complete manual for the device Kenmore Water System, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenmore Water System by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenmore Water System.

A complete Kenmore manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenmore Water System - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenmore Water System, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenmore Water System, that we can find in the current document
3. Tips how to use the basic functions of the device Kenmore Water System - which should help us in our first steps of using Kenmore Water System
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenmore Water System
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenmore Water System in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenmore Water System?

Use the form below

If you did not solve your problem by using a manual Kenmore Water System, ask a question using the form below. If a user had a similar problem with Kenmore Water System it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)