-
TP-Link TD-VG3631 - page 1
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router 1910010643 Rev: 1.0.1 ...
-
TP-Link TD-VG3631 - page 2
COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other brands and product names are trademarks or registered trademarks of t heir respective holders. No part of the specific ations may be reproduced in any form or by any means or used to m ake any derivativ ...
-
TP-Link TD-VG3631 - page 3
FCC STATEMENT This equipment has been tested and found to comply wi th the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen erates, uses and can radiate radio frequency energy and, if no ...
-
TP-Link TD-VG3631 - page 4
National Restrictions This device is intended for home and office use in all EU countries (and ot her countries following the EU directive 1999/5/EC) wit hout any limitation except for the countries m entioned below: Country Restriction Reason/remark Bulgaria None General authorization require d for outdoor use and public service France Outdoor use ...
-
TP-Link TD-VG3631 - page 5
Industry Canada Statement: This device complies with RSS-210 of the Industr y Canada Rules. Operati on is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference re ceived, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure ...
-
TP-Link TD-VG3631 - page 6
TP-LINK TECHNOLOGIES CO., L TD TP-LINK TECHNOLOGIES CO., L TD Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China DECLARA TION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N VoIP ADSL2+ Modem Router Model No.: TD-VG3631 T rademark: TP-LINK ...
-
TP-Link TD-VG3631 - page 7
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Product Overview ................................................................................... 2 1.1 Overview of the Modem Router .......................................................................... ...
-
TP-Link TD-VG3631 - page 8
4.6 Wireless ........................................................................................................................ 43 4.6.1 Basic Settings .................................................................................................................... 43 4.6.2 WPS Settings ..................................................... ...
-
TP-Link TD-VG3631 - page 9
4.12.3 WAN Host ......................................................................................................................... 86 4.12.4 Schedule ........................................................................................................................... 88 4.13 Traffic Control ............................................. ...
-
TP-Link TD-VG3631 - page 10
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1 Package Content s The following contents should be found in your package: ¾ One TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router ¾ One Power Adapter for TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router ¾ Quick Installation Guide ¾ One RJ45 cable ¾ Three RJ11 cables ¾ ...
-
TP-Link TD-VG3631 - page 11
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 2 Chapter 1. Product Overview Thank you for choosing the TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router . 1.1 Overview of the Modem Router The TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP. Powered by 2x2 MI ...
-
TP-Link TD-VG3631 - page 12
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 3 1.2 Main Features ¾ Four 10/100M bps Auto-Negotiation RJ45 LAN po rts (Auto MDI/MDIX), four RJ11 ports, two USB 2.0 ports ¾ Provides external splitter. ¾ Adopts Advanced DMT modulati on and demodulation technology. ¾ Supports bridge mode and Router function. ¾ Multi-user sharin ...
-
TP-Link TD-VG3631 - page 13
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The Router’s LEDs are located on the front panel (V iew from left to right). They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Status Indication On The modem router is ...
-
TP-Link TD-VG3631 - page 14
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 5 On A valid PSTN connection. Flash Incoming calls and outgoing calls are transmitted trough PSTN line. （ Line ） Off PSTN connection fails. On The phone is off hook. Flash The phone is ringing. （ Phone1-2 ） Off The phone is on hook. On A wireless device has been success fully ...
-
TP-Link TD-VG3631 - page 15
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 6 1.3.2 The Back Panel The Router's ports, where the c ables are connected, and RESET bu tton are located on the front. Figure 1-2 ¾ POWER: The Power plug is where yo u will connect the power adapter. ¾ USB1/USB2: The USB port connects to a USB storage device or a USB printer. ...
-
TP-Link TD-VG3631 - page 16
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 7 Figure 1-3 ¾ WPS : The switch for the WPS functi on. For details, please refer to 4.6.2 WPS Settings . ¾ WiFi : The switch for the WiFi function. ¾ ON/OFF : The switch for the power. ...
-
TP-Link TD-VG3631 - page 17
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 8 Chapter 2. Connecting the Modem Router 2.1 System Requirement s ¾ Broadband Internet Access Service (DSL/Cable/Ethernet). ¾ PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. ¾ TCP/IP protocol on each PC. ¾ Web browser, such as Micr osoft Internet Ex ...
-
TP-Link TD-VG3631 - page 18
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 9 Step 5: Power on the computers and LAN devices. Step 6: Attach the power adapter. Connect the power ad apter to the power connector on the rear of the device and plug in the adapter to an el ectrical outlet or pow er extension. The electrical outlet shall be installed near the devic ...
-
TP-Link TD-VG3631 - page 19
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 10 Chapter 3. Quick Inst allation Guide 3.1 Configuring the PC After you directly connect your PC to the Modem Router or connect your adapter to a Hub/Switch which has connected to t he Modem Router, you need to confi gur e your PC’s IP address. Follow the steps below to configure i ...
-
TP-Link TD-VG3631 - page 20
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 11 Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP) , and then click the Properties button. Figure 3-3 ...
-
TP-Link TD-VG3631 - page 21
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 12 Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK . Figure 3-4 ) Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server addre ss automatically” in the screen above. Now, ...
-
TP-Link TD-VG3631 - page 22
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 13 If the result displayed is similar to the screen shown belo w, it means t hat your PC has not connected to the Modem Router. Figure 3-6 You can check it follo wing the steps below: 1) Is the connection between your PC and the Modem Router correct? The LEDs of LAN port which you lin ...
-
TP-Link TD-VG3631 - page 23
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 14 Figure 3-8 ) Note: 1) Do not mix up the user name and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-br owser has been set to a proxy. Go to Tools menu → Network → LAN S ...
-
TP-Link TD-VG3631 - page 24
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 15 Figure 3-9 3. Change the VPI or VCI values which are used to define a unique path for your connection. If you have been given specific settings for this to configuration, type in the correct values assigned by your ISP. Click Next . ...
-
TP-Link TD-VG3631 - page 25
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 16 Figure 3-10 4. Here we select PPPoE WAN Link Type for example, enter the Username , Passw ord and Confirm Password given by your ISP, and then click Next . Figure 3-11 5. On the Wireless screen, we use the default SSID, select Region and Mode . Set a Password or select Disable Secu ...
-
TP-Link TD-VG3631 - page 26
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 17 6. Basic parameters of Voice can be set on the Voice screen. Please enter a profile name to identify this account and other parameters provided by yo ur ISP. If you don’t want to configure VoIP function now, leave "Pro file Name" blank and click Next to skip. Figure 3-1 ...
-
TP-Link TD-VG3631 - page 27
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 18 Figure 3-15 ...
-
TP-Link TD-VG3631 - page 28
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 19 Chapter 4. Configuring the Modem Router This chapter will show each Web page's key function and the c onfiguration way. 4.1 Login After your successful login, you will see the fift een main menus on the left of the Web-based utility. On the right, there are the corres ponding ...
-
TP-Link TD-VG3631 - page 29
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 20 Figure 4-1 4.3 Quick Setup Please refer to Section 3.2 Quick Installation Guide . 4.4 Network Choose “ Netw ork ”, there are many submenus under the main menu. Click any one of them, and you will be able to configur e the corresponding function. ...
-
TP-Link TD-VG3631 - page 30
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 21 4.4.1 WAN Settings Choose “ Netw ork ” Æ “ WAN Settings ”, and you will see the WAN Port Information Table in the screen similar to Figure 4-2 , which describes the WAN port setti ngs and the relevant manipulation to each interface. There are five different configurations ...
-
TP-Link TD-VG3631 - page 31
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 22 Figure 4-3 4.4.1.1 Static IP Select this option if your ISP prov ides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below. ...
-
TP-Link TD-VG3631 - page 32
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 23 Figure 4-4 ATM Configuration: ¾ VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. ¾ VCI (1~65535): Identifies the virtual channel endpoints in an ATM network. The valid rang ...
-
TP-Link TD-VG3631 - page 33
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 24 ¾ DNS Server/ Secondary DNS Server: Here you can set DNS Server (at least one) manually. The Route will use this DNS Server for priority. ¾ Default Gatewa y: select a WAN Interface from the drop-down list as the IPv4 default gateway. ¾ MTU (bytes): Maximum Transmission Unit Size ...
-
TP-Link TD-VG3631 - page 34
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 25 Figure 4-5 Click Advanced , advanced selections for WAN Service Setup can be shown. ¾ MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not re commended that you change the default value unless ...
-
TP-Link TD-VG3631 - page 35
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 26 ¾ Primary DNS Server/ Secondary DNS Server: Choose “Set DNS Server manually”, you can set DNS Server (at least one) manually here. T he Route will use this DNS Server for priority. Click the Save button to save the settings. 4.4.1.3 PPPoE If your ISP provides a PPPoE connectio ...
-
TP-Link TD-VG3631 - page 36
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 27 ¾ Authentication Method: Select the Authentication Method from the drop-down list, the default method is AUTO_AUTH , and you can leave it as a default setting. ¾ Choose the right connection type according to your needs: For PPPoE connection, you can select Connect on demand or Co ...
-
TP-Link TD-VG3631 - page 37
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 28 Figure 4-7 4.4.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the WAN service t ype on the screen. ...
-
TP-Link TD-VG3631 - page 38
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 29 Figure 4-8 ¾ IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. If you forget, you can ask your ISP. ¾ DNS Server/Secondary DNS Server: Type in your preferred DNS server. ¾ Default Gatewa y: select a WAN Interface from the drop-down list as the IPv4 de ...
-
TP-Link TD-VG3631 - page 39
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 30 Figure 4-9 ) Note: After you finish the Internet configuration, please click Save to m ake the settings take e ffe ct. 4.4.2 EWAN Choose “ Netw ork ” Æ “ EWAN ”, and you will see the Ethernet WAN Interface screen similar to Figure 4-10 . There are three different configura ...
-
TP-Link TD-VG3631 - page 40
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 31 Figure 4-10 4.4.2.1 Dy n ami c IP Select this option, the Modem Router will be abl e to obtain IP network information dynamically from a DHCP server provided by your ISP (as shown Figure 4-10 ). The next configuration is similar to Dynamic IP over ATM interface (see section 4.4.1.2 ...
-
TP-Link TD-VG3631 - page 41
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 32 Figure 4-11 4.4.2.3 PPPoE If your ISP provides a PPPoE connection and you need to use an Ethernet Interface, select PPPoE option for the WAN service type on the screen. The following configuration is similar to PPPoE over ATM interface (see section 4.4.1.3 PPPoE ). ...
-
TP-Link TD-VG3631 - page 42
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 33 Figure 4-12 4.4.3 Interface Grouping Choose “ Network ” Æ “ Interface Grouping ”, you can view all the current groups on this page (shown in Figure 4-13 ). Figure 4-13 ...
-
TP-Link TD-VG3631 - page 43
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 34 ¾ VLAN: Enable or disable this function. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same LAN, when in fact they are located on a number of different LAN segments. Because VLANs are b ...
-
TP-Link TD-VG3631 - page 44
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 35 Figure 4-15 ¾ IP Address: You can configure the Modem Router’s IP Address and Subnet Mask for LAN Interface. • IP Address: Enter the Modem Router’s local IP A ddress, then you can access to the Web-based Utility via the IP Addre ss, the default val ue is 192.168.1.1. • Sub ...
-
TP-Link TD-VG3631 - page 45
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 36 • Leased Time: The Leased Time is the amount of ti me in which a network user will be allowed connection to the Modem Router with thei r current dynamic IP address. Enter the amount of time, in hours, then the user will be “leased” this dynamic IP address. After the dynamic I ...
-
TP-Link TD-VG3631 - page 46
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 37 Figure 4-17 ¾ Virtual Private Network (VPN) - VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pa ss through the Modem Router. • PPTP Passthrough - Point-to-Point Tunneling Pr otocol (PPTP) allows the Point-to-Point Protocol (PPP) to be t u ...
-
TP-Link TD-VG3631 - page 47
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 38 Figure 4-18 ¾ DSL Modulation Type: Select the DSL operation Modulation Type which your DSL connection uses. ¾ Annex Type: Select the DSL operation Annex Type which your DSL connection uses. Click the Save button to save your settings. 4.5 DHCP Server Choose “ DHCP Server ”, y ...
-
TP-Link TD-VG3631 - page 48
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 39 Figure 4-19 ¾ Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Modem Router is 192.168.1.1, the default Start IP Address is 192.168.1.100 , and the Start IP Address must be 192.168.1.100 or greater, ...
-
TP-Link TD-VG3631 - page 49
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 40 ) Note: 1) To use the DHCP server func tion of the Modem Router, you mu st configure all computers on the LAN as "Obtain an IP Address automatically". 2) Y ou have to disable NA T of the W AN connections, or the DHCP Relay may not take ef fect. 3) If you select Disabled , ...
-
TP-Link TD-VG3631 - page 50
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 41 Figure 4-21 ¾ MAC Address: The MAC address of the PC for which you want to reserve an IP address. ¾ IP Address: The IP address reserved for the PC by the Modem Router. ¾ Status: The status of this entry either Enabled or Disabled . To Reserve an IP address: 1. Click the Add Ne w ...
-
TP-Link TD-VG3631 - page 51
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 42 Figure 4-23 To add a vendor class: 1. Click the Add Ne w button. Then Figure 4-24 will pop up. 2. Enter parameters for the vendor class. Click the Save button. Figure 4-24 To modify or delete an existing entry: 4. Click the Edit in the entry you want to modify. If you want to delet ...
-
TP-Link TD-VG3631 - page 52
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 43 4.6 Wireless Choose “ Wireless ”, there are six submenus to configure Wireless LAN settings. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.6.1 Basic Settings Choose “ Wireless ...
-
TP-Link TD-VG3631 - page 53
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 44 11bg mixed: Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed: Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can be connec ted to ...
-
TP-Link TD-VG3631 - page 54
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 45 ¾ WEP Index: This option should be chos en if the key type is WEP(ASCII) or WEP(HEX). It indicates the index of the WEP key. ¾ Auth Type: This option should be chos en if the key type is WEP(ASCII) or WEP(HEX). It indicates the authorizati on type of the Root AP. ¾ Password : If ...
-
TP-Link TD-VG3631 - page 55
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 46 You can also keep the default WPS Status as Enabled and click the Add device button in Figure 4-26 , then Choose “ Press the button of the new device in two minutes ” and click Connect . (Shown in the following figure) Figure 4-27 Step 2: Press and hold the WPS button of the cl ...
-
TP-Link TD-VG3631 - page 56
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 47 Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then click Connect button. Step 3: “ Connect successfully ” will appear on the screen of Figure 4-28 , which means the client device has successfully connected to the Modem Router. III. En ...
-
TP-Link TD-VG3631 - page 57
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 48 Figure 4-29 ¾ Disable Wireless Security: If you do not want to use wire less security, check this radio button. But it’s strongly recommended to choose one of the following m odes to enable security. ¾ WEP: It is based on the IEEE 802. 11 standard. If you check this radio butto ...
-
TP-Link TD-VG3631 - page 58
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 49 • WEP Key - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identic al on all wireless stations in your network. • Key Type - You can select the WEP key length (64-bi t, or 128-bit, or 152-bit.) for encryptio ...
-
TP-Link TD-VG3631 - page 59
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 50 ¾ Description: A simple description of the wireless station. To Add a Wireless MAC Addre ss filtering entry, click the Add New button. The following page will appear, shown in Figure 4-32 : Figure 4-32 To add or modify a MAC Address Filtering entry, follo w these instructions: 1. ...
-
TP-Link TD-VG3631 - page 60
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 51 5) Click the Back button. The filtering rules that configured s hould be similar to the following list: 4.6.5 Wireless Advanced Choose menu “ Wireless ” Æ ” Wireless Advanced ”, you can configure t he advanced settings of your wireless network. Figure 4-33 ¾ Transmit Powe ...
-
TP-Link TD-VG3631 - page 61
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 52 You can specify the va lue between 1 -255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. ¾ Enable Short GI: This function is recommended for it will increase the data capacity by reducing the guard interval time . ¾ Ena ...
-
TP-Link TD-VG3631 - page 62
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 53 4.7.1 SIP Account Choose “ Voice ” Æ “ SIP Account ”, you will see the screen similar to Figure 4-35 . SIP accounts are necessary for making VoIP calls. This se ction intro duces how to setup the SIP(Session Initiation Protocol ) account for your Modem Router. Figure 4-35 ...
-
TP-Link TD-VG3631 - page 63
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 54 Figure 4-36 SIP Account Basic ¾ Profile Name: Assign a name to identify the profile. Pl ease note that special characters are not allowed. ¾ Phone Number: Enter the phone number of the account you applied. ¾ Display Name: Assign a name for your account. This name is the Caller-I ...
-
TP-Link TD-VG3631 - page 64
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 55 ¾ Preferred Receive Ptime: Ptime, short for packet time, refers to the time interval for a voice packet to be sent by the remote caller. The unit is ms (millisecond). Usually the default value 20ms is OK. ¾ Priority: Select a priority for this account. This pr iority is useful wh ...
-
TP-Link TD-VG3631 - page 65
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 56 Figure 4-37 ¾ Prefix: Displays the prefix of your plan. This prefix refers to the initial digit(s) of the num bers you dial. ¾ Op: Displays the operation of this plan. ¾ Destination: Displays the account or network used for this plan. ¾ Enable: Displays the interface( s) enable ...
-
TP-Link TD-VG3631 - page 66
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 57 If “TimeOut” is selected, the dia ling will be sent out when timeou t starts. The timeout activates when no more digits are dial ed in a specific duration; If “#” is selected, the dialing w ill not be sent until “#” is dialed; If “#/TimeOut” is selected, the dialing ...
-
TP-Link TD-VG3631 - page 67
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 58 Figure 4-40 ¾ Prefix: Set number(s) as the prefix. Up to 16 characters can be entered. ¾ Interface Barring: You can check any box to disable in terface(s). Numbers matching prefix in Forbidden Call list are not allowed to be dialed out through the selected interface(s). For examp ...
-
TP-Link TD-VG3631 - page 68
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 59 Figure 4-42 ¾ Phone Enable: Check the box behind to enable the function. Dial Settings ¾ Dial Plan Priority: The parameters configured here deter mine which network or SIP account to use when making outgoing calls. In the 1 st field, there are options of networks. Please note if ...
-
TP-Link TD-VG3631 - page 69
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 60 • PSTN Preferred & Account X (a certain account ) – The Router will select the network to make calls according to your dial plans set on Dial Plan page. If VoIP network is selected, the account used will be Account X. But if no dial plan is ma tched with your outgoing call, ...
-
TP-Link TD-VG3631 - page 70
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 61 through selected account when "No answer" time is out. Please note that network or account available here varies with that in Dial Plan Priority field. Telephony Settings ¾ VAD Support: VAD(Voice Activation Detection) prev ents transmitting the silence packets to consume ...
-
TP-Link TD-VG3631 - page 71
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 62 ¾ DSCP for SIP/RTP: DSCP(Differentiated Services Code Poin t) is the first 6 bits in the ToS byte. DSCP marking allows users to assign s pecific application traffic to be executed in priority by the next Router based on the DSCP value. Select DSCP for the SIP( Session Initiation P ...
-
TP-Link TD-VG3631 - page 72
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 63 4.7.5 Speed Dial Choose “ Voice ” Æ “ Speed Dial ”, you will see the screen as shown in Figure 4-44 . This section introduces how to configure S peed Dial for your account. Speed Dial function can help to st ore frequently used telephone numbers a nd make your dial more co ...
-
TP-Link TD-VG3631 - page 73
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 64 Figure 4-47 ¾ Call Log: Check the Enable if you want to make this function take effect; otherwise check the Disable. ¾ Start: Beginning time of the call. ¾ Source: Caller ID, either phone number or IP address. ¾ Dest: Callee ID, either phone number or IP address. ¾ Typ e: Call ...
-
TP-Link TD-VG3631 - page 74
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 65 Call Firewall can be used to control incoming calls. This section introduces how to configure the Call Firewall. Choose “ Voice ” Æ “ Call Firewall “ Æ “ Mode Setting “, you will see the screen as shown in Figure 4-49 . Figure 4-49 ¾ Call Firewall Enable: Check the b ...
-
TP-Link TD-VG3631 - page 75
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 66 Figure 4-51 Enter a number with the length in t he range of [3, 16]in the field of Black List Number and Click the Save button to make the configuration take effe ct, then you will go back to the previous page and see the following list as shown in Figure 4-50 . If you want to dele ...
-
TP-Link TD-VG3631 - page 76
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 67 in Black List and 2224 in White List, with Bl ack List mode enabled, incoming call number 2224510 will be allowed. 4.7.8 USB Voice Mail Choose “ Voice ” Æ “ USB Voice Mail “, you will see the screen as shown in Figure 4-54 . USB Voice mail is used to record voice messages ...
-
TP-Link TD-VG3631 - page 77
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 68 Figure 4-55 ¾ Enable Local Play Operation Notify: Check this box so there will be sound indication for operation when you listen to the voice messages. This is enabled by default. If you are very familiar with the operation s, you can disable it. ¾ Enable Global Wav Format: Check ...
-
TP-Link TD-VG3631 - page 78
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 69 3) Input the PIN code according to the notification. 4) You can listen to all the new mess ages after the PIN code is validated. Click Save to save your configurations. Click Back to go back to the previous page, i.e. Figure 4-54 . 4.8 USB Settings There are six submenus under the ...
-
TP-Link TD-VG3631 - page 79
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 70 ¾ Capacity: The storage capacity of the USB driver. ¾ Status: Indicates the shared or non-shared status of the volume. Active means volume can be shared, while Inactive means volume can not be shared. If Deactivate in Action field is enabled, Inactive will be displayed in the Sta ...
-
TP-Link TD-VG3631 - page 80
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 71 4. Re-enter the password in the Confirm Password field. 5. Click the Set button, and then a new entry will be added in the table. 6. Click the Apply button to apply your settings. Click the Refresh button to refresh this page immediately. 4.8.3 Storage Sharing Choose menu “ USB S ...
-
TP-Link TD-VG3631 - page 81
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 72 Figure 4-59 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder Click the Enab ...
-
TP-Link TD-VG3631 - page 82
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 73 Figure 4-60 ¾ Server Status: Indicates the FTP Server's current status. ¾ Internet Access: Enable or disable this function. ¾ Internet Address: If Internet Access is enabled, WAN IP will be displayed here. ¾ Service Port: Enter the FTP Port number to use. The default is 21 ...
-
TP-Link TD-VG3631 - page 83
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 74 Figure 4-61 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder. Click the Ena ...
-
TP-Link TD-VG3631 - page 84
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 75 ¾ Server Enable: Select this box to enable this function. ¾ Server Name: The name of this Media Server. To add a new share folder for your media server, please follow the instructions below: a) Click Add Ne w Folder button, and you will see the screen as shown in Figure 4-77 . b) ...
-
TP-Link TD-VG3631 - page 85
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 76 4.9 Route Settings Choose “ Route Settings ”, it includes three menus : Default Gatew ay , Static Route and RIP Settings . The detailed descriptions are provided below. 4.9.1 Default Gateway Choose “ Route Settings ” Æ “ Default Gatewa y ”, you can see the Default Gate ...
-
TP-Link TD-VG3631 - page 86
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 77 Figure 4-67 2. Enter the following data: ¾ Destination IP Address: The Destination IP Addr ess is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask: The Subnet Mask determines which portion of an IP Address is the network portion, and whi ...
-
TP-Link TD-VG3631 - page 87
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 78 ) Note: RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE). 4.10 Forwarding There are four submenus under the Forwarding menu: Virtual Servers , Port Triggering , DMZ and UPnP . Click any of them, and you will be able to configure the corre sponding ...
-
TP-Link TD-VG3631 - page 88
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 79 2. Select the service y ou want to use from the Common Service Port list. If the Common Service Port menu does not list the serv ice that you want to use, enter the number of the service port or service port range in the Service Port field. 3. Select the service you want to use fro ...
-
TP-Link TD-VG3631 - page 89
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 80 Figure 4-71 To add a new rule, follow the steps below. 1. Click the Add Ne w button, the next screen will pop-up as shown in Figure 4-72 . 2. Select a co mmon application from the Common Service Port drop-down list, then the Trigger Port field and the Open Ports field will be autom ...
-
TP-Link TD-VG3631 - page 90
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 81 ¾ Open Protocol: The protocol used for Incoming Port , either TCP , UDP , or ALL (all protocols supported by the Modem Router). ¾ Status: The status of this entry, Enabled means the Port Triggering entry is enabled. ¾ Modify: To modify or delete an existing entry. ¾ Common Serv ...
-
TP-Link TD-VG3631 - page 91
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 82 Figure 4-73 To assign a computer or server to be a DMZ server: 1. Click the Enable button. 2. Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field. 3. Click the Save button. 4.10.4 UPnP Choose menu “ Forwarding → UPnP ”, and then you ...
-
TP-Link TD-VG3631 - page 92
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 83 Click the Disable button to disable UPnP. Click the Refresh button to update the Curr ent UPnP Settings List. 4.11 Parent al Control Choose menu “ Parental Control ”, and you can configure the paren tal control in the screen as shown in Figure 4-75 . The Parental Control functi ...
-
TP-Link TD-VG3631 - page 93
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 84 ¾ MAC Address of Current PC: This field displays the MA C address of the PC that is managing this Modem Router. If the MAC Address of your adapter is registered, you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above. ¾ Add URL: ...
-
TP-Link TD-VG3631 - page 94
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 85 ¾ Edit: Here you can edit or delete an existing rule. ¾ Add New: Click the Add New button to add a new rule entry. ¾ Enable Selected: Click the Enable Selected button to enable the selected rules in the list. ¾ Disable Selected: Click the Disable Selected button to disable the ...
-
TP-Link TD-VG3631 - page 95
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 86 Figure 4-78 ¾ Description: Here displays the description of the host and this description is unique. ¾ Address Info: Here displays the information about the host. It can be IP or MAC. ¾ Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Clic ...
-
TP-Link TD-VG3631 - page 96
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 87 Figure 4-80 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In IP Address field, enter the IP address. If you select MAC Address , the screen shown is Figure 4-81 . Figure 4-81 1) In Description field, create a unique description for the host (e. ...
-
TP-Link TD-VG3631 - page 97
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 88 4.12.4 Schedule Choose menu “ Firewall ” → “ Schedule ”, and then you can view and set a Schedule list in the next screen as shown in Figure 4-83 . Figure 4-83 ¾ Description: Here displays the description of the schedule and this description is unique. ¾ Edit: Here you ...
-
TP-Link TD-VG3631 - page 98
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 89 Click the Delete Selected button to delete the select ed entries in the table. 4.13 T raffic Control There are two submenus under the Traffic Control menu: Control Settings and Rules L ist . Click any of them, and you will be able to confi gure the corresponding function. The detai ...
-
TP-Link TD-VG3631 - page 99
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 90 Figure 4-86 ¾ Description: This is the information about the rules such as address range. ¾ Upstream Bandwidth: This field displays the max and mix u pload bandwidth through the WAN port, the default is 0. ¾ Downstream Bandw idth: This field displays the max and mix download ban ...
-
TP-Link TD-VG3631 - page 100
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 91 There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List . Click any of them, and you will be able to scan or configure the corre s ponding function. The detailed explanations for eac h submenu are provided below. 4.14.1 Binding Settings This page di ...
-
TP-Link TD-VG3631 - page 101
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 92 To modify or delete an existing entry, follow the steps below. 1. Find the desired entry in the table. 2. Click Edit as desired on the Edit colu mn. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete se ...
-
TP-Link TD-VG3631 - page 102
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 93 Figure 4-91 ¾ Service Provider: This field displays the service provider of DDNS. ¾ Domain Name: Enter the Domain name you received from dynamic DNS service provider. ¾ Username & Password: Type the “User Name” and “Password” for your D DNS account. ¾ Enable DDNS: A ...
-
TP-Link TD-VG3631 - page 103
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 94 4.17 System T ools Choose menu “ System Tools ”, and you can see the s ubmenus under the main menu: System Log , Time Settings , Manage Control , CWMP Settings , SNMP Settings , Backup & Res tore , Factory Defaults , Firm ware Upgrade , Reboot and Statistics. Click any of t ...
-
TP-Link TD-VG3631 - page 104
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 95 Figure 4-94 ¾ Save Locally: If Save Locally is selected , events will be recorded in the local memory. ¾ Minimum Level: Select the Minimum level in the drop-down list, for the Minimum Level, all logged events above or equal to the selected level will be displayed. ¾ Save Remotel ...
-
TP-Link TD-VG3631 - page 105
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 96 3. Enter the Time in Hour/Minute/Second format. 4. Click Save . To set time automatically: 1. Select your local time zone. 2. Enter the address or domain of the NTP Server 1 or NTP Server 2 . 3. Click the Get GMT butto n to get system time from In ternet if you have connected to th ...
-
TP-Link TD-VG3631 - page 106
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 97 Figure 4-97 ¾ CWMP: Select enable the CWMP function. ¾ Inform: Enable or disable the function. If enabl ed, the information will be informed to ACS server periodically. ¾ Inform Interval: Enter the interval time here. ¾ ACS URL: Enter the website of ACS whic h is provided by yo ...
-
TP-Link TD-VG3631 - page 107
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 98 Figure 4-98 An SNMP Agent is an application running on the Modem Router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs. So a rout er contains SNMP "agent" software ...
-
TP-Link TD-VG3631 - page 108
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 99 Figure 4-100 Click the Restore button to reset all configuration settings to their default values. • The default User Name : admin • The default Password : admin • The default Subnet Mask : 255.255.255.0 ) Note: All changed settings will be lost when defaults are restored. 4. ...
-
TP-Link TD-VG3631 - page 109
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 100 1) New firmware vers ions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firm ware unle ss the new firmware has a new featur e you want to use. However, when experiencing probl ems caused by the Modem Router rather than the con ...
-
TP-Link TD-VG3631 - page 110
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 101 Figure 4-103 ¾ Statistics Status: Enable or Disable. The default value is disabled. To enable it, click the Enable . If it is disabled, the func tion of DoS protection in Securi ty settings will be disabled. ¾ Statistics Interval (5-60): The default value is 10. Select a value b ...
-
TP-Link TD-VG3631 - page 111
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 102 Appendix A: S pecifications General Standards and Protocols ANSI T1.413.I2, ITU G.992.1, ITU G. 992.2, ITU G.992.3, ITU G.992.5, IEEE802.1p, IEEE 802.11b,IEEE 802.11e, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IE EE 802.3u, TCP/IP, PPPoA, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT Safety &a ...
-
TP-Link TD-VG3631 - page 112
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 103 Appendix B: T roubleshooting T1. How do I restore my Modem Router’ s configuration to its factor y default settings? With the Modem Router powered on, press and hold the RESET button on the front pan el for 8 to 10 seconds before releasing it. ) Note : Once the Modem Router is r ...
-
TP-Link TD-VG3631 - page 113
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 104 Click Change adapter settings Click Properties Right-click Local Area Connection ...
-
TP-Link TD-VG3631 - page 114
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 105 Double-click Internet Protocol Version 4 (TCP/IPv4) Click OK Select Obtain DNS server address automatically Select Obtain an IP address automatically ...
-
TP-Link TD-VG3631 - page 115
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 106 For Windows Vista OS Go to Start > Settings > Control Panel , and then you will see the following page. Click View network status and tasks Click View status Click Properties ...
-
TP-Link TD-VG3631 - page 116
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 107 Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK ...
-
TP-Link TD-VG3631 - page 117
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 108 For Windows XP OS Go to Start > Control Panel , you will then see the following page. Click Network Connections Right-click Local Area Connection Click Network and Internet Connections Click Properties ...
-
TP-Link TD-VG3631 - page 118
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 109 Double-click Internet Protocol (TCP/IP) Select Obtain DNS server address automatically Select Obtain an IP address automatically Click OK ...
-
TP-Link TD-VG3631 - page 119
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 110 Click OK 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options ...
-
TP-Link TD-VG3631 - page 120
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 111 Click OK Select Never dial a connection Now, try to log on to the Web- based configuration page again afte r the above settings have been configured. If you still cannot acce ss the configuration page, please restore your Modem Router’s factory default settings and re configure ...
-
TP-Link TD-VG3631 - page 121
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 112 2) Insert the provided Resource CD into CD-ROM drive of your computer. 3) Please select your product model and click Start Setup . 4) Then the configur ation wizard will pop up and show you how to connect your devices. After that, the Easy Setup Assistant will start. Click NEXT , ...
-
TP-Link TD-VG3631 - page 122
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 113 5) When it comes to Configure USB Voice Mail page, check boxes before Configure USB Voice Mail and Send Files to USB Disk . Then click NEXT to continue. 6) Follow the step-by-step instructions unt il you comes to the finish screen. Click FINISH to close this wizard. ...
-
TP-Link TD-VG3631 - page 123
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 114 7) The configure files can be found in your USB device which means you have successfully configured the USB device for USB Voice Mail function. ...
-
TP-Link TD-VG3631 - page 124
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 115 Appendix C: T elephony Features This section introduces what the following features are used for. Call Holding This feature allows you to put a call on hold, in which case the call is not ended but no verbal communication is available. To put a call on hold, press the FLASH button ...
-
TP-Link TD-VG3631 - page 125
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 116 Anonymous Call Blocking With this feature enabled, all anonymous calls will be blocked. Speed Dial This feature allows you to create short number s for your freq uently used telephone numbers to make your dialing more convenient. You just need to press one or two digits and the ke ...
-
TP-Link TD-VG3631 - page 126
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 117 Appendix D: T elephone Operation The table below guides you to c onfigure some frequently used call f eatures using keypads on your telephone. For the featur es mentioned in this table, please refer to Telephony Features in Appendix C . Code Description Usage *20 Listen to voice m ...
-
TP-Link TD-VG3631 - page 127
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 118 effect. *72 Enable Call Forwarding on Busy. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to ma ke the configuration take effect. *73 Enable Call Forwarding Unconditionally. Pick up the phone to dial this code. After hearing the confirmation ton ...
-
TP-Link TD-VG3631 - page 128
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 119 Disturb). confirmation tone, hang up to make the configuration take effect. *87 Disable DND (Do Not Disturb). Pick up the phone to dial this code. After hearing the confirmation tone, hang up to ma ke the configuration take effect. ...
-
TP-Link TD-VG3631 - page 129
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 120 Appendix E: T echnical Support Technical Support For more troubleshooting he lp, go to: http://www.tp-link.com/e n/support/faq T o download the latest Firmware, Driver , Utility a nd User Guide, go to: http://www .tp-link .com/en/support/do wnload For all other technic ...
Do you have a question concerning TP-Link TD-VG3631?
Use the form below
If you did not solve your problem by using a manual TP-Link TD-VG3631, ask a question using the form below. If a user had a similar problem with TP-Link TD-VG3631 it is likely that he will want to share the way to solve it.