-
Pelco WLV2500 - page 1
® P elco • 3500 Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981 FAX (800) 289-9150 or (1-559) 292-3827 WL V2500 Series Wir eless Control Link and V ideo T ransmission Systems Installation/Operation Manual C914M (7/96) ...
-
Pelco WLV2500 - page 2
ii Pelco Manual C914M (7/96) ®Pelco and the Pelco logo are registered trademarks of Pelco. ©Copyright 1996, Pelco. All rights reserved. T ABLE OF CONTENTS Section Page 1.0 W ARNINGS .................................................................................................................... .................... 1 2.0 SCOPE ................ ...
-
Pelco WLV2500 - page 3
LIST OF ILLUSTRA TIONS Figur e Page 1T ypical WL V500 Control Link and WL V2000 Video Link Configuration ............................................ 2 2T ransmitter-Receiver Placement at Same Site ................................................................................ 3 3 Multiple System Interference ...................................... ...
-
Pelco WLV2500 - page 4
(This page intentionally left blank.) iv Pelco Manual C914M (7/96) ...
-
Pelco WLV2500 - page 5
Pelco Manual C914M (7/96) 1 This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 4 .O nly use replacement parts recom ...
-
Pelco WLV2500 - page 6
2 Pelco Manual C914M (7/96) 2.0 SCOPE This manual covers the installation of the WL V2500 Series of outdoor wireless systems. 3.0 DESCRIPTION To make a WL V2500 system, a WL V500 control sys- tem is combined with a WL V200 video transmission system (refer to Figure 1). The wireless control systems of the WL V500 Series provide wireless remote contr ...
-
Pelco WLV2500 - page 7
Pelco Manual C914M (7/96) 3 Figure 2. T ransmitter-Receiver Placement at Same Site 4.0 ANTENNA LOCA TION To provide the best reception, proper placement of the transmit and receive antennas is important. Reception will be best when: • The antennas are a minimum of 8-10 feet above the floor (indoors) or ground (outdoors). • The transmit and rece ...
-
Pelco WLV2500 - page 8
4 Pelco Manual C914M (7/96) 5.0 INST ALLA TION NOTE: Proper placement of the transmit and receive antennas is important for best reception. Read Section 4.0, “Antenna Lo- cation,” before installing the equipment. Install the WL V500 receiver and WL V2000 transmit- ter at the remote site where your camera will be. Install the WL V500 transmitter ...
-
Pelco WLV2500 - page 9
Pelco Manual C914M (7/96) 5 5.2 WIRING NOTE: In the following steps w hen you as- semble coaxial cable, install a BNC connector on only one end. Run the bare end of the cable through the cable entry gland on the enclosure so that the end with the BNC connector is inside the enclosure. Then add a BNC connector to the other end of the cable. Refer to ...
-
Pelco WLV2500 - page 10
6 Pelco Manual C914M (7/96) 5.4 ANTENNA ALIGNMENT NOTE: This section applies only to the WL V2000 wireless receiver . 1. Connect a high impedance voltmeter to the RSSI (Received Signal Strength Indication) test points on the bottom of the enclosure: a. Set the voltmeter on a low-volt DC scale (3 or 10 volts). b. Connect the negative lead from the v ...
-
Pelco WLV2500 - page 11
Pelco Manual C914M (7/96) 7 4. Check the power supply voltages for the wireless transmitter and receiver . If the voltage at the trans- mitter or receiver is less than 1 1 VDC, replace the unit’ s power supply . 5.5.2 Poor Picture 1. Refer to Section 4.0, “Antenna Location,” and verify that the transmit and receive antennas are positioned pro ...
-
Pelco WLV2500 - page 12
8 Pelco Manual C914M (7/96) 6.0 EXPLODED ASSEMBL Y DIAGRAM (OUTDOOR MODELS ONL Y) Figure 6. Outdoor Enclosure Exploded Assembly Diagram ...
-
Pelco WLV2500 - page 13
Pelco Manual C914M (7/96) 9 6.1 MECHANICAL P ARTS LIST Item Quantity Description Part Number 11 9-Pin Connector CON03-06-1091 22 Gland EH400010003 32 Gland Nut EH400010004 41 Gland CX950010000 51 Gland Nut CX950010001 62 Fuse Holder FUS342012L 71 Power Supply Assembly PCB9000281ASSY 81 3-Position T erminal Block TRB3-140Y 91 Tr ansformer T RF21162. ...
-
Pelco WLV2500 - page 14
10 Pelco Manual C914M (7/96) 7.0 INTERCEPT ® DOME MODIFICA TION To use the WL V500 wireless control system with In- tercept ® dome drives DD08CXX, DD08EXX, DD14CXX, or DD14EXX (domes with 360 degree ro- tation), the following steps must be performed: NOTE : Refer to Figure 7, which gives a gen- eral layout of the dome drive and indicates the item ...
-
Pelco WLV2500 - page 15
Pelco Manual C914M (7/96) 11 Figure 8. V ideo Board Component Locations Figure 9. Block Diagram ...
-
Pelco WLV2500 - page 16
12 Pelco Manual C914M (7/96) Figure 10. Coaxitron ® Receiver Backplane PCB - Wire Lead Additions and Wiring Diagram ...
-
Pelco WLV2500 - page 17
Pelco Manual C914M (7/96) 13 8.0 WIRING DIAGRAM NOTE: Output voltage is 15 VDC, not 10.5 Figure 1 1. Outdoor Enclosure Wiring Diagram 9.0 MAINTENANCE In cold, wet areas periodically visit the transmitter and receiver sites to prevent the buildup of snow and ice on the enclosures. A buildup of ice and snow will severely attenuate the microwave signa ...
-
Pelco WLV2500 - page 18
14 Pelco Manual C914M (7/96) Impedance: 75 ohms Connectors: BNC RF (WL V500) T ransmitter Radiated Power: FCC Part 15 (15.249) T ransmit Antenna: Attached, circular -polarized, patch antenna Receive Antenna: Removable, 1 1 dBi, circular- polarized, patch antenna Receiver Connector: TNC Receiver Input Impedance: 50 ohms Frequency Range: 2400 to 2483 ...
-
Pelco WLV2500 - page 19
Pelco Manual C914M (7/96) 15 11.0 W ARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1996, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective ...
-
Pelco WLV2500 - page 20
Pelco 3500 Pelco Way, Clovis, CA 93612-5699 (559) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (559) 292-3827 International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.) C914M ...
Do you have a question concerning Pelco WLV2500?
Use the form below
If you did not solve your problem by using a manual Pelco WLV2500, ask a question using the form below. If a user had a similar problem with Pelco WLV2500 it is likely that he will want to share the way to solve it.