-
Fluke pmn - page 1
405 ESSEX ROAD, NEPTUNE, NJ 07753 TEL: (732) 922-9300 FAX: (732) 922-9334 INSTRUCT ION MANUAL FOR 83-493-001 Revision G MODEL SERIAL NUMBER ...
-
Fluke pmn - page 2
Table of Contents 4 - 1 4.1 Remote Control 4 - 1 4 OPERA T ION 3 - 4 3.6.4 For Units with O/P Voltage > 6KV: 3 - 4 3.6.3 For Units with O/P Voltage £6KV 3 - 4 3.6.2 Output Gr ound Connection 3 - 3 3.6.1 Grounding of Input Line 3 - 3 3.6 Grounding the Product 3 - 3 3.5 Connecting High Voltage Output 3 - 2 3.4 Power Cord Spe cification: 3 - 1 3.3 ...
-
Fluke pmn - page 3
6 - 1 6.3 Calibration 6 - 1 6.2 Main tenance 6 - 1 6.1 Safety Precautions 6 - 1 6 MA INTEN A NCE A ND CA LIBRA TION 5 - 5 5.7 Long Charge T ime W ith Power Factor Corrected (PFC) Units 5 - 4 5.6 Continuous HV DC Operation (Constant Voltage) 5 - 4 5.5 Determining AC Line Current 5 - 3 5.4 Measuring High Voltages 5 - 2 5.3 Paralleling Units 5 - 1 5.2 ...
-
Fluke pmn - page 4
...
-
Fluke pmn - page 5
...
-
Fluke pmn - page 6
" " " " Input Voltage selective by Terminal Block position *Note: In p ut cur rent ratin gs given are m axi mu m wh en out put Repeti tion Ra te is =>10Hz. ...
-
Fluke pmn - page 7
90%, non-condensing ! ! ! ! ? ...
-
Fluke pmn - page 8
2.23.4 SUFFIX -EN "Low Enable" - A +10 to 15 volt (high) si gnal will disable power supply operation. A 0 to +1.5 volt (low) signal will enable t he supply. 2.23.5 SUFFIX -5V 0 to +5 volt voltage (0 to full-scale output) programming 2.23.6 SUFFIX -LP Latching overload pr otection. 2.23.7 SUFFIX -110 100 to 120 VAC input option f or non-po ...
-
Fluke pmn - page 9
Figure 2-1 Mechanical Dimensions for 500A, 102A, 152A Outputs up to 6KV (for grounding instruct ions see SECTION 3.6) 83-493-001 Revision G 2 - 5 Specifications ...
-
Fluke pmn - page 10
Figure 2-2 Mechanical Dimensions for 500A, 102A, 152A Outputs from 7KV t o 40K V (for grounding instruct ions see SECTION 3.6) 83-493-001 Revision G 2 - 6 Specifications ...
-
Fluke pmn - page 11
Figure 2-3 Mechanical Dimensions for 202A Outputs up to 6KV (for grounding instruct ions see SECTION 3.6) 83-493-001 Revision G 2 - 7 Specifications ...
-
Fluke pmn - page 12
Figure 2-4 Mechanical Dimensions for 202A Outputs from 7KV t o 40K V (for grounding instruct ions see SECTION 3.6) 83-493-001 Revision G 2 - 8 Specifications ...
-
Fluke pmn - page 13
? ...
-
Fluke pmn - page 14
The PFC version connection i s shown in Figure 3-2. Connect t he input voltage line wires to L2 and COM terminals. WA RNING: 152A a nd 202A PFC M odels are only av ailable w ith 220 VA C Nominal. For 152A Models Suffix 110 at 110-120 VA C must be operated w ith the i nternal fuses F1 and F2 (on the I nverter Board) replaced by copper bus provided w ...
-
Fluke pmn - page 15
? ...
-
Fluke pmn - page 16
3.6.1 GROUNDING OF I NPUT LINE The supply is grounded through the ground terminal of the input conne ctor. A protective ground connection by the way of the grounding conductor in the input te rminal is essential for safe operat ion. 3.6.2 OUTPU T GROUND CONNECT ION It is important that there be a ground connect ing the supply to the load as shown i ...
-
Fluke pmn - page 17
? ...
-
Fluke pmn - page 18
Figure 4-1 Eample Of Interface Connection 83-493-001 Revisi on G 4 - 2 Operations ...
-
Fluke pmn - page 19
& & & & ...
-
Fluke pmn - page 20
For clarif ication and fur ther technic al assist ance speci fic to your applicat ion, please cont act Lambda EMI . ? ...
-
Fluke pmn - page 21
Figure 5.2 Output Current Measurement A series terminating resis tor (or series i nductor or cla mp diode) m us t be added as shown if the average value of the peak current exceeds 110% of the normal output curr ent. When choosing Rs, ensure it can wit hstand the full out put voltage across it as well as the power dissipati on caused by discharging ...
-
Fluke pmn - page 22
WA RNING: ...
-
Fluke pmn - page 23
Figure 5.3 HV Bias Measurements ? ...
-
Fluke pmn - page 24
! ! ! ! ? ...
-
Fluke pmn - page 25
? ...
Do you have a question concerning Fluke pmn?
Use the form below
If you did not solve your problem by using a manual Fluke pmn, ask a question using the form below. If a user had a similar problem with Fluke pmn it is likely that he will want to share the way to solve it.