English dropdown-ico

Manual MaxTech 56K BPS

21 pages 0.06 mb
Download

Go to site of 21

Summary
  • MaxTech 56K BPS - page 1

    Part #MAN117 Rev. 1.0 K56Plus/HIS-FM High Performance K56Plus/V.34+/V.42bis 56K BPS Plug & Play Internal FAX/Data Modem User's Manual Contents Section One - Introduction .......................... 1 Section Two - Installation ............................ 1 Section Three - AT Command Set .............. 7 Section Four - S Registers ......... ...

  • MaxTech 56K BPS - page 2

    The information contained in this manual has been validated at the time of this manual's production. The manufacturer reserves the right to make any changes and improvements in the product de- scribed in this manual at any time and without notice. Consequently the manufacturer assumes no liability for damages incurred directly or indi- rectly ...

  • MaxTech 56K BPS - page 3

    1 Section One - Introduction This 56 Kbps* Plug and Play FAX/Data Modem connects your computer to all popular high speed modems available today. The modem incorporates “K56Plus” (56Kbps) technology to provide increased download speeds using regular telephone lines. The modem incorporates Plug and Play for ease of instal- lation. This manual des ...

  • MaxTech 56K BPS - page 4

    2 Proceed to Section 2.3 now if you have every- thing required. If you have neither 2A or 2B above, you have two options to provide Plug and Play functionality to your PC. 1. Install Windows 95 or, 2. If running DOS or Windows 3.x, configure the modem using the included modem driver. Instructions for installing this driver are included in the text ...

  • MaxTech 56K BPS - page 5

    3 4. Carefully slide the internal modem into the slot you have chosen, applying even pressure until the modem is completely seated in the slot. 5. Fasten the retaining bracket with the screw from the slot cover. Make sure the modem is properly aligned. Store the slot cover for future use. 6. Replace the computer cover and plug in your computer. 7. ...

  • MaxTech 56K BPS - page 6

    4 • Section 2.4.1.1 when Windows 95 starts for the first time after card installation, it detects the modem and it displays the New Hardware Found dialog box • Section 2.4.1.2 when Windows 95 starts for the first time after card installation, it detects the modem and it displays the Update Device Driver Wizard . 2.4.1.1 Windows 95 Release 4.00. ...

  • MaxTech 56K BPS - page 7

    5 2.4.2 Configuring in a Plug and Play System with- out Windows 95 When this modem is installed in a Plug and Play system without Windows 95, the computer's BIOS will assign a COM port and IRQ line to the modem. Proceed to Section 2.5, Software Installation/ Configuration. 2.4.3 Configuring in a Non-Plug and Play System Computers without nativ ...

  • MaxTech 56K BPS - page 8

    6 Note that your software must be configured to communicate with the modem on the same COM port and IRQ line used by the modem. 2.6 Testing Your Modem After Installation In order to test your modem you should be familiar with your communication software. Load and set up your communication software and enter into “terminal mode.” Make sure that ...

  • MaxTech 56K BPS - page 9

    7 contain reference material, and can be skipped. If you have difficulties getting your modem to work, read Section 6 - Troubleshooting to find answers to com- monly asked questions and problems. Section Three - AT Command Set 3.1 Executing Commands Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Comma ...

  • MaxTech 56K BPS - page 10

    8 D _ 0 - 9, A-D, # and * L last number redial P pulse dialing T touch-tone dialing W wait for second dial tone , pause @ wait for five seconds of silence ! flash ; return to Command Mode after dialing DS=n Dial one of the four telephone numbers (n=0-3) stored in the modem’s non- volatile memory. E_ E0 Commands are not echoed E1 Commands are echo ...

  • MaxTech 56K BPS - page 11

    9 Sr=n Set register r to value n (n = 0-255). T Set Tone Dial as default V_ V0 Numeric responses V1 Word responses W_ W0 Report DTE speed only W 1 Report line speed, error correction protocol, and DTE speed. W2 Report DCE speed only X _ X0 Hayes Smartmodem 300 compatible responses/blind dialing. X 1 Same as X0 plus all CONNECT responses/blind diali ...

  • MaxTech 56K BPS - page 12

    10 &K5 Enable transparent XON/XOFF flow control &K6 Enable both RTS/CTS and XON/XOFF flow control &L_ &L0 Modem is set up for dial-up operation &M_ &M0 Asynchronous operation &P_ &P0 US setting for off-hook-to-on-hook ratio &P1 UK and Hong Kong off-hook-to-on-hook ratio &P2 Same as &P0 setting but at 20 p ...

  • MaxTech 56K BPS - page 13

    11 %E_ %E 0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,d.e,f Select modulation where: a =0, 1, 2, 3, 9, 10, 11, 56, 64, 69; b =0-1; c =300- 56000; d =300-56000; e =0-1; and f =0- 1. A, b, c, d, e, f default= 56, 1, 300, 5600 ...

  • MaxTech 56K BPS - page 14

    12 &Q_ &Q0 Direct data link only (same as N1) &Q5 V.42 data link with fallback options &Q6 Normal data link only (same as N0) A_ A0 64-character maximum MNP block size A1 128-character maximum MNP block size A2 192-character maximum MNP block size A3 256-character maximum MNP block size Bn Send a 1/10 second line break to th ...

  • MaxTech 56K BPS - page 15

    13 Table 4-1 S - Registers Register Function Range/units Default S0 Auto-answer Ring 0-255 /rings 0 S1 Ring counter 0-255 /rings 0 S2 Escape code character 0-127 /ASCII 43 S3 Carriage return character 0-127 /ASCII 13 S4 Line feed character 0-127 /ASCII 10 S5 Backspace character 0-32, 127 /ASCII 8 S6 Dial tone wait time 2-255 /seconds 2 S7 Remote ca ...

  • MaxTech 56K BPS - page 16

    14 S49-81 Reserved S82 Break options 3, 7, or 128 1 28 S83-85 Reserved S86 Connection failure code 0, 4, 5, 9, 12, 13, 14 S87-S90 Reserved S91 Transmit attenuation 0-15/dBm 10 S92 Fax attenuation 0-15/dBm 10 S95 Extended result code options Bit-mapped register 0 Section Five - Result Codes OK 0 CONNECT 1 RING 2 NO CARRIER 3 ERROR 4 CONNECT 1200 5 N ...

  • MaxTech 56K BPS - page 17

    15 Section Six - Troubleshooting This section describes some of the common problems you may encounter while using your modem. If you can not resolve your difficulty after reading this chapter, contact your dealer or vendor for assistance. Modem does not respond to commands. 1. Make sure the communication software is configured to “talk” to the ...

  • MaxTech 56K BPS - page 18

    16 used. 2. Make sure the correct terminal emulation mode is being used (see communication software manual). High pitch tone is heard whenever you answer the phone. 1. Make sure Auto-Answer is turned off. Your modem is factory configured to NOT auto-answer. Issue AT&F to factory reset your modem. Modem experiences errors while communicating wit ...

  • MaxTech 56K BPS - page 19

    17 Appendix A - Specifications Communication Std. K56FLEX (56Kbps), V.34, V.32bis, V.32, V.29, V.27ter, V.22bis, V.23, V.22, V.21, V.17, Bell212/103 Data Compression: V.42bis/MNP5 Error Correction: V.42/MNP2-4 Host Interface: 16 bit PC bus COM ports: 1, 2, 3, 4 IRQ lines: 3, 4, 5, 7, 9, 10, 11, 12, 15 FAX Group: Group III Send/Receive Standard FAX ...

  • MaxTech 56K BPS - page 20

    18 The FCC prohibits this equipment to be connected to party lines or coin-telephone service. In the event that this equipment should fail to operate properly, disconnect the equipment from the phone line to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or ven- dor. The FCC als ...

  • MaxTech 56K BPS - page 21

    19 permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an ...

Manufacturer MaxTech Category Network Card

Documents that we receive from a manufacturer of a MaxTech 56K BPS can be divided into several groups. They are, among others:
- MaxTech technical drawings
- 56K BPS manuals
- MaxTech product data sheets
- information booklets
- or energy labels MaxTech 56K BPS
All of them are important, but the most important information from the point of view of use of the device are in the user manual MaxTech 56K BPS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals MaxTech 56K BPS, service manual, brief instructions and user manuals MaxTech 56K BPS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product MaxTech 56K BPS.

Similar manuals

A complete manual for the device MaxTech 56K BPS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use MaxTech 56K BPS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of MaxTech 56K BPS.

A complete MaxTech manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual MaxTech 56K BPS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the MaxTech 56K BPS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the MaxTech 56K BPS, that we can find in the current document
3. Tips how to use the basic functions of the device MaxTech 56K BPS - which should help us in our first steps of using MaxTech 56K BPS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with MaxTech 56K BPS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of MaxTech 56K BPS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning MaxTech 56K BPS?

Use the form below

If you did not solve your problem by using a manual MaxTech 56K BPS, ask a question using the form below. If a user had a similar problem with MaxTech 56K BPS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)