English dropdown-ico

Manual Planet Technology WAP-4000

57 pages 2.85 mb
Download

Go to site of 57

Summary
  • Planet Technology WAP-4000 - page 1

    802.11g W irele s s Access Poin t / Bridge W A P-4000 User ’ s Manual ...

  • Planet Technology WAP-4000 - page 2

    Co p y right Copyright  2003 by PLANE T T echnology Corp . A ll righ t s r eserved . No par t of t his publication ma y be reproduced, t r ansmit t ed, t r anscribed, s t ored in a ret r ieval system, or translated into any language or compu t er language , in any form or by any means , electronic, mechanical , magne t ic, optical , chemical, ma ...

  • Planet Technology WAP-4000 - page 3

    Federal Communication Commission (FCC) Radiation Exposu r e Statement This equipment complies w ith FCC radia t ion e x posure set f orth for an uncontrolled envi r onment. In orde r to avoid the possibility of e x ceeding the FCC r adio f r equency e x posure limi t s , human p r o x imity to the an t enna shall not be less than 20 cm(8 inches) du ...

  • Planet Technology WAP-4000 - page 4

    T A BLE OF CONTENTS C H A P T ER 1 IN T RODUC T I O N ................................................................................................. .1 1.1 P ACKAGE C ON T ENTS ........................................................................................................ .1 1.2 S YSTEM R EQUIREME N TS .................................. ...

  • Planet Technology WAP-4000 - page 5

    5.4 M U L TIPLE B RID G E MODE ................................................................................................. . 51 C H A P T ER 6 T ROUBLES H OO T IN G ...................................................................................... . 52 ...

  • Planet Technology WAP-4000 - page 6

    - 1 - Chapter 1 I ntroduction Thank you for pu r chasing WAP-4000. W A P-4000 is an I EEE 802. 1 1g W ireless A ccess Poin t . IEE E 802. 1 1g uses 2.4GHz frequency band , the same as IEEE 802. 1 1b; but it p r ovides more throughput rate than 802. 1 1b . The ma x imum t hroughput rate of 802. 1 1g can up to 54 M bps. W A P-4000 is also back w ard ...

  • Planet Technology WAP-4000 - page 7

    - 2 - 1.4 Speci f ica t ion S t andard IEEE 802. 1 1b, IEEE 802. 1 1g Signal T ype DSSS (Direct Sequence S pread S pect r um) M odulation BPSK / QPSK / CCK / OFDM Port 10/100Base-T X (RJ-45) * 1 Antenna De t achable Dipole A ntenna * 1 Antenna Connec t or Reversed Polarity S M A M ale Output Po w er 17dBm 802. 1 1b 11 M bps (CCK): -82d B m 5.5 M bp ...

  • Planet Technology WAP-4000 - page 8

    - 3 - Input P o w er DC 5V, 2.5A Certification FCC, CE 1.5 W ireles s P e rf o rmance The follo w ing info r ma t ion w ill help you utilizing t he w ireless performance, and opera t ing co v erage of W A P-4000. 1. Site se l ection T o avoid interfe r ences , please locate W A P-4000 and w ireless clien t s a w ay from trans f orme r s, mic r o w ...

  • Planet Technology WAP-4000 - page 9

    - 4 - Chapter 2 H ard w a re Installation Before you p r oceed w ith the ins t allation, it is necessary that you have enough info r ma t ion about the W A P-4000 . 1. Locate an optimum location for the W A P-4000. T h e be s t place f or your WAP-4000 is usually at the center of your w ireless net w ork, w ith line of sight to all of your mobile s ...

  • Planet Technology WAP-4000 - page 10

    - 5 - Chapter 3 C onf i guring the Wire l ess A c ce s s Po i nt W A P-4000 can be con f igu r ed via w eb bro w ser or bundled utilit y . It is st r ongly recommended to configure and manage W A P-4000 using a w ired LAN compute r . 3.1 Configur e t h rough Web Br o w s er W eb configura t ion provides a user-f r iendly graphical user in t erface ...

  • Planet Technology WAP-4000 - page 11

    - 6 - 3.1. 1 Wizard Setup w izard provides a simple w ay to con f igu r e you r W A P - 4000 . Clicking “ W iza rd ” button on top panel of W A P-4000 ’ s w eb page, Se t up W izard w ill pop up as belo w .. To quick configure W A P - 4000, please follo w the steps belo w to complete t he configura t ion. Click “ Ne x t> ” to continue ...

  • Planet Technology WAP-4000 - page 12

    - 7 - Enter the SSID of your W LAN and select t he f r equency channel. Click “ Ne x t> ” . Step 3. Set Encr y ption Y ou can enable W E P encryp t ion and set W E P key in this sc r een. Click “ Ne x t> ” to continue . Step 4. Restart Please click the “ Res t art ” but t on to save the set t ings and r es t art W A P - 4000. In t ...

  • Planet Technology WAP-4000 - page 13

    - 8 - 3.1. 2 St atus: Y ou can check your W A P - 4000 se t tings and s t a t us in this screen . Y ou can click the “ V ie w Log ” button , and t hen the screen belo w w ill appea r . Y ou can vie w the logged message he r e. Y ou can also clear or r efresh the log record . ...

  • Planet Technology WAP-4000 - page 14

    - 9 - 3.1. 3 Ba s ic Settings: Y ou can set t he A P Name, SS I D, Channel and W E P func t ion to this A ccess Point. A f ter con f iguration , please click Apply t o save you r set t ings. AP Name : The host name o f the W A P-4000. This can be any name for you to easily identify this access point. SSID : The SSID is the name shared among all poi ...

  • Planet Technology WAP-4000 - page 15

    - 10 - I P address : This address is a unique numbe r s that identi f ies a computer or device on the WAN o r LAN. These numbe r s a r e usually sho w n in grou p s sepa r ated by periods, for e x ample: 123.123.23 . 2. Subnet Mask : Subne t s allo w net w ork tra ff ic bet w een hos t s t o be se p arated based on t he net w ork's con f igura ...

  • Planet Technology WAP-4000 - page 16

    - 11 - 3.1.5 A d v an c ed Settings: Y ou can set t he W A P-4000 operation mode and relative settings. A f ter configuration, please click Apply to save your set t ings. AP Mode: WAP-4000 has f ou r opera t ion modes. By default, it is set to A P mode . A ccess Point: This mode is set to W A P - 4000 by de f ault . This connec t s your w ireless P ...

  • Planet Technology WAP-4000 - page 17

    - 12 - RTS Threshold: Use this field to specify a value fo r the R TS Threshold . Ente r a value bet w een 256 and 2346. This value should r emain at i t s default set t ing o f 2346. S hould you encounter inconsistent da t a f lo w , only minor modifica t ions are recommended. Fragmen t ation Threshold: This field is used to specify the fragmen t ...

  • Planet Technology WAP-4000 - page 18

    - 13 - Password : Enter the ne w pass w ord in the " AP Pass w ord Ne w " field and again in the ne x t field to con f irm . Click on " A pply" to execu t e t he pass w ord change . The Pass w ord is case - sensi t ive, and can be made up o f any keyboa r d characte r s. The ne w pass w ord mus t be bet w een 0 and 15 characte r ...

  • Planet Technology WAP-4000 - page 19

    - 14 - Enable/D i sable: Enable or disable 802 . 1 X authentication of W A P-4000. Encr y ption K e y: Select one of the Encryp t ion key leng t h options. I t should be set t he same leng t h as W EP ke y . Select one of the Encryption key life t ime options. Once the life t ime e x pires, RADIU S server w ill rene w the Encryp t ion ke y . RADIUS ...

  • Planet Technology WAP-4000 - page 20

    - 15 - 3.1. 8 T ools: Y ou can backup or restore W A P-4000 set t ings, reset W AP-4000 t o factory default and upg r ade firm w are in this option. Backup Sett i ngs : Y ou can backup current set t ings to a file. Press “ Backup ” but t on, it will p r omp t you a loca t ion t o save the backup f ile (config.bin ). Restore S ettings : W hen yo ...

  • Planet Technology WAP-4000 - page 21

    - 16 - 3. Y ou can click “ Bro w se ” to specify the Destination Folder that you w ant to ins t all t he utilit y . Or you can keep the de f aul t setting and click ” Ne xt ” to continue. 4. Please click “ Finish ” t o complete the so f t w are ins t allation . ...

  • Planet Technology WAP-4000 - page 22

    - 17 - 3.2.2 54M A P Utili t y c onfiguration A f ter ins t alling u t ilit y , you can f ound t he icon on your desk t op, please double click this icon to run t he configura t ion u t ilit y and select each option to se t up you r Access Point as you need . A ft er settings in each option, please press “ Apply ” to save . It w ill sho w you t ...

  • Planet Technology WAP-4000 - page 23

    - 18 - 3.2. 2 .2 A P Settings Basic Sett i ngs : ESSID : ESSID is used by all w ireless devices w ithin the w ireless net w ork . The ESSID value mus t be the same on all s t ations and A ccess poin t s in this W LAN. Channel : Select the appropriate channel f r om the list provided to cor r espond w ith your ne tw or k settings, bet w een 1 and 13 ...

  • Planet Technology WAP-4000 - page 24

    - 19 - A d vance se t ting: w hen you press the “ Advance Set t ing button ” , t he dialog bo x belo w w ill appea r . Y ou can set more de t ails parame t ers in this sc r een . SSID Broadcast: This allo w s the A P t o broadcast i t s SSID. Other w ireless client w ith si t e survey function can easily kno w this SSID and use this SS I D to c ...

  • Planet Technology WAP-4000 - page 25

    - 20 - 3.2. 2 .3 I P Settings Fix I P A ddress : Y ou may give a fi x ed I P add r ess to W A P - 4000 manually by choosing t his radio button. I P A ddress: Set an I P add r ess for t he A P . Subnet mask: Set the Subne t M ask for the A P . Gate wa y: The I P address o f a gate w ay device necessa r y for communica t ion w ith devices ou t side t ...

  • Planet Technology WAP-4000 - page 26

    - 21 - 3.2. 2 .4 WEP Settings Da t a Encr y ption : Select this option w hen you w ant to enable W EP f unction. A uth. Mode : Open A uthentication: W i t h t his set t ing , any s t ation in the W LAN can receives and transmi t s da t a f r om the A ccess Point (null authentication). Shared A uthenticat i on : W i t h this set t ing, only s t atio ...

  • Planet Technology WAP-4000 - page 27

    - 22 - 3.2. 2 .5 8 02 . 1x Settings 802.1X Funct i on: Enable or disable 802.1 X authentica t ion o f WAP-4000. Encr y ption K e y: Select one of the Encryp t ion key leng t h options. I t should be set t he same leng t h as W EP ke y . Select one of the Encryption key life t ime options. Once the life t ime e x pires, RADIU S server w ill rene w t ...

  • Planet Technology WAP-4000 - page 28

    - 23 - Chapter 4 8 0 2. 1 X A uthenticat i on Setup 4.1 8 02. 1 X Infra s tructure An 802.1 X Infrastructu r e is composed o f three majo r componen t s: Authenticato r , Au t hen t ication serve r , and Supplicant. A uthentication server: An entity t hat provides an authentication service to an authenticator . This service de t ermines, from the c ...

  • Planet Technology WAP-4000 - page 29

    - 24 - 6. The client validates the digi t al cer t ificate, and replies i t s o w n digi t al cer t ifica t e to t he R A DIUS serve r . 7. The RADIUS server valida t es client ’ s digi t al cer t ificate. 8. The client and RADIUS se r ver derive encryption keys. 9. The RADIUS server sends WAP-4000 a RADIUS ACCEP T message, including the client ? ...

  • Planet Technology WAP-4000 - page 30

    - 25 - 6. Enter the info r ma t ion tha t you w ant for your Ce r tifica t e Service, and click “ Next ” to continue . 7. Go to S t art > Program > A dministra t ive Tools > Certif i cate A uthori t y . 8. Right-click on the “ Poli c y S etting ” , select “ new ” . 9. Select “ Certi f ica t e to Issue ” . 10. Selec t “ A ...

  • Planet Technology WAP-4000 - page 31

    - 26 - 11. Go to Start > Program > A dministrative Tools > A ctive Director y Users and Computers . 12. Right-click on domain, and select ” Properties ” to con t inue. 13. Selec t “ Group Pol i cy ” tab and click “ Properties ” to con t inue . ...

  • Planet Technology WAP-4000 - page 32

    - 27 - 14. Go to “ Compu t er Configuration ” > “ Securi t y Settings ” > “ Public K e y Policies ” 15. Right-click “ A utomatic Certificate Request S etting ” , and select “ New ” 16. Click “ A utomatic Certif i cate Request ... ” ...

  • Planet Technology WAP-4000 - page 33

    - 28 - 17. The Au t oma t ic C erti f icate Request Setup W iza r d w ill guide you th r ough the Automa t ic Certi f icate Request setup , simply click “ Next ” th r ough to t he last step. 18. Click “ Fin i sh ” to complete the Au t omatic Certi f icate Request Setup 19. Go to Start > Run , and type “ command ” and click “ Enter ...

  • Planet Technology WAP-4000 - page 34

    - 29 - Setting In t ernet Authenticat i on Service 24. Go to Start > Program > A dministrative Tools > Inte r net A uthentication Service . 25. Right-click “ Cl i ent ” , and select “ N e w C l ient ” . 26. En t er the IP address of W AP-4000 in the Client address te x t field, a memorable name for W A P-4000 in t he Cl i ent-Vendo ...

  • Planet Technology WAP-4000 - page 35

    - 30 - 27. Click “ F i nish ” . 28. In the Inte r net Authentication Service, right - click “ R emo t e A ccess Pol i cies ” 29. Selec t “ New Remote A ccess Pol i cy ” . 30. Selec t “ D a y - A nd-Time-Restriction ” , and click “ A dd ” to continue . ...

  • Planet Technology WAP-4000 - page 36

    - 31 - 31. Unless you w ant to specif y the active dura t ion for 802.1 X authentication, click “ OK ” to accept for having 802.1 x authentication enabled a t all times. 32. Selec t “ Grant remo t e access pe r miss i on ” , and click “ Next ” to continue. ...

  • Planet Technology WAP-4000 - page 37

    - 32 - 33. C lic k “ Edit Profile ” . For TLS Authenticat i on Setup (Steps 34 ~ 35 ) 34. Selec t “ A uthentication ” Tab. 35. Enable “ Extensible A uthentication Protocol ” , and select “ Smart C ard or other Cert i ficate ” f or TLS au t hen t ication. Click “ OK ” . Then go t o step 38. ...

  • Planet Technology WAP-4000 - page 38

    - 33 - For M D5 Authentication S e t up (Steps 36 ~ 37 ) 36. Selec t “ A uthentication ” Tab. 37. Enable “ Extensible A uthentication Protocol ” . Select “ MD5-Challenge ” and enable “ E ncr y pted A uthentication (CH A P) ” for MD5 authentication. Click “ OK ” . ...

  • Planet Technology WAP-4000 - page 39

    - 34 - 38. Selec t “ Internet A uthentication Service (Local) ” , click on “ Action ” f r om t op panel. Then click “ Register Service i n A ctive Directory ” . 39. Go to Start > Program > A dministrative Tools > A ctive Director y Users and Computers. 40. Right click on the domain, and select “ Properties ” . 41. Selec t ? ...

  • Planet Technology WAP-4000 - page 40

    - 35 - 42. Go to “ Computer Conf i guration ” > “ Windows S ettings ” > “ Securi t y Settings ” > “ A ccount Policies ” > “ Password Pol i c i es ” . D ouble click on “ S t ore password us i ng reversib l e enc r y ption for all users in the domain ” . ...

  • Planet Technology WAP-4000 - page 41

    - 36 - 43. Click “ Define this poli c y s etting ” , select “ E nab l ed ” , and click “ OK ” to continue . 44. Go to Start > Program > A dministrative Tools > A ctive Director y Users and Computers . 45. Go to Users . R ight - click on the use r tha t you are granting access, and selec t “ Propert i es ” . 46. Go to “ A ...

  • Planet Technology WAP-4000 - page 42

    - 37 - 48. Go to the “ Dial-in ” tab , and check “ A llo w access ” op t ion for Remote Access Pe r mission and “ No Call-back ” for Callback Options. Then click “ OK ” . ...

  • Planet Technology WAP-4000 - page 43

    - 38 - 4.3 A uthenticator Setup 1. For E A P-MD5 Au t hen t ication, W E P key must be set previously. Go t o Bas i c Sett i ngs. Enable W E P key, and en t er a desired key s t ring. Y ou can skip this step if using E A P-TLS Authen t ication . 2. Click on 802.1X for detailed con f iguration. ...

  • Planet Technology WAP-4000 - page 44

    - 39 - 3. Enable 802 . 1 X Authentica t ion by selecting “ Enable ” . 4. If E A P-MD5 is used, you can leave t he set t ings in Encr y p tion K e y Length and Lifet i me as default. I f you are using E A P-TLS authentication, set t he Encr y ption K e y Length ranging from 64 t o 256 B its and the Li f etime from 5 M inutes to 1 Day. As soon as ...

  • Planet Technology WAP-4000 - page 45

    - 40 - 4.4.1 E A P-MD5 A uth e ntication 1. Go to S t art > Control P anel, double - click on “ Ne t work Connections ” . 2. Right-click on the W ireless Net w ork Connection w hich using W L - 3555. 3. Click “ Properties ” to open up the P r oper t ies setting w indo w . 4. Click on the “ Wireless Ne t work ” t ab. 5. Click “ Prop ...

  • Planet Technology WAP-4000 - page 46

    - 41 - 6. Select “ Da t a encr y ption (WEP enabled ) ” option, but leave othe r op t ions unselected . 7. Enter the net w ork key in “ N e t w ork k ey ” t e x t bo x . The string must be t he same as the fi r st set o f W E P key w hich you set t o W A P-4000. 8. Click “ OK ” . ...

  • Planet Technology WAP-4000 - page 47

    - 42 - 9. Select “ A uthentication ” tab. 10. Selec t “ Enab l e ne t work access contro l using IEEE 802.1X ” to enable 802 . 1 x authentica t ion. 11. Selec t “ MD-5 Challenge ” f rom the drop-do w n list bo x for EAP type. 12. Click “ OK ” . 13. W hen w ireless client has associated w ith W A P - 4000, a user authentication notic ...

  • Planet Technology WAP-4000 - page 48

    - 43 - 4.4.2 E A P-TLS A u thentication Get Digital Certif i cate from S erver The follo w ing procedu r es are based on ob t aining a certi f ica t e from W indo w s 2000 Server w hich acts as a CA server. Fu r the r more , you mus t have a valid account/pass w ord to access the server . 1. Ac t ive w eb bro w ser, en t er “ http:/ / 192 . 168 . ...

  • Planet Technology WAP-4000 - page 49

    - 44 - 4. Select “ User Certificate request ” , and click “ Next ” t o continue. 5. Click “ Submit > ” to con t inue. ...

  • Planet Technology WAP-4000 - page 50

    - 45 - 6. The Certi f icate Service is no w processing the cer t ificate request. 7. The cer t ifica t e is issued by t he server, click “ Install t his certificate ” t o do w nload and sto r e the certi f icate t o your local compu t er. ...

  • Planet Technology WAP-4000 - page 51

    - 46 - 8. Click “ Y es ” to s t ore the certifica t e to your local computer . 9. Certi f icate is no w installed. Wireless Adapter S etup 1. Go to S t art > Control P anel, double - click on “ Ne t work Connections ” . 2. Right-click on the W ireless Net w ork Connection w hich using W L - 3555. 3. Click “ Properties ” to open up th ...

  • Planet Technology WAP-4000 - page 52

    - 47 - 5. Click “ Properties ” of one a v ailable w ireless net w ork, w hich you w ant to associate w ith . 6. Select “ The k e y is provided for me automatica l ly ” option. ...

  • Planet Technology WAP-4000 - page 53

    - 48 - 7. Click “ OK ” . 8. Click “ A uthentication ” tab 9. Select “ Enable ne t work access control using IEEE 802 . 1X ” op t ion t o enable 802.1 x authen t ica t ion. 10. Selec t “ Smart Card or other Certificate ” from the drop-do w n list bo x for EAP type. 11. Click “ OK ” . 12. W hen w ireless client has associated w it ...

  • Planet Technology WAP-4000 - page 54

    - 49 - certi f icate f or w ireless net w ork connec t ion. If you only have one certi f ica t e in local compute r , system w ill automatically use it f or authen t ica t e. If you have mul t iple certifica t es in local compute r , click on the net w ork connection icon in t he system tray to continue . 13. Selec t the cer t ifica t e that w as i ...

  • Planet Technology WAP-4000 - page 55

    - 50 - Chapter 5 A ppl i cation This chapter describe the four opera t ing mode of your W A P-4000 . The four w orking modes of W A P-4000 are Access P oint , Access Point Client M ode, W ireless Bridge mode and M ultiple B r idge mode. 5.1 A ccess Point mode W i t h t his mode, you r W ireless net w ork connection could act as follo w ing. Any of ...

  • Planet Technology WAP-4000 - page 56

    - 51 - 5.3 W ireles s Bridge mode The W i r eless Bridge mode help to make the t w o Ethernet ne tw orks connected w ithout any w ire. W i t h t w o W A P-4000s in this mode, the tw o LANs in dis t ance can communica t e to each o t he r . This could be deployed if the net w orks are hard to make t he w ire in bet w een. Please be noted, key in the ...

  • Planet Technology WAP-4000 - page 57

    Chapter 6 Troubleshooting This chapter provides solutions to problems usually encoun t ered during the ins t alla t ion and ope r ation of the W A P-4000. The W A P-4000 canno t power up. Use an electrical test meter to dete r mine the ou t put vol t age of the po w er suppl y . Check if it matched the speci f ication of W AP-4000. Cannot commun i ...

Manufacturer Planet Technology Category Network Router

Documents that we receive from a manufacturer of a Planet Technology WAP-4000 can be divided into several groups. They are, among others:
- Planet Technology technical drawings
- WAP-4000 manuals
- Planet Technology product data sheets
- information booklets
- or energy labels Planet Technology WAP-4000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Planet Technology WAP-4000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Planet Technology WAP-4000, service manual, brief instructions and user manuals Planet Technology WAP-4000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Planet Technology WAP-4000.

Similar manuals

A complete manual for the device Planet Technology WAP-4000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Planet Technology WAP-4000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Planet Technology WAP-4000.

A complete Planet Technology manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Planet Technology WAP-4000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Planet Technology WAP-4000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Planet Technology WAP-4000, that we can find in the current document
3. Tips how to use the basic functions of the device Planet Technology WAP-4000 - which should help us in our first steps of using Planet Technology WAP-4000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Planet Technology WAP-4000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Planet Technology WAP-4000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Planet Technology WAP-4000?

Use the form below

If you did not solve your problem by using a manual Planet Technology WAP-4000, ask a question using the form below. If a user had a similar problem with Planet Technology WAP-4000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)