English dropdown-ico

Manual Cabletron Systems Expansion module 9E106-06

40 pages 0.8 mb
Download

Go to site of 40

Summary
  • Cabletron Systems Expansion module 9E106-06 - page 1

    SmartSwitch 9000 9E106-06 Ethernet Switch Module User’s Guide ...

  • Cabletron Systems Expansion module 9E106-06 - page 2

    ...

  • Cabletron Systems Expansion module 9E106-06 - page 3

    i Notice Notice Cabletron Systems r eserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made. The hardwar e, firmware, or softwar e described in this manual is subject to ...

  • Cabletron Systems Expansion module 9E106-06 - page 4

    ii Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation. NOTE: This equipment has been tested and found to c ...

  • Cabletron Systems Expansion module 9E106-06 - page 5

    iii Notice DOC Notice This digital apparatus does not exceed the Class A limits for radio noise emissions fr om digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de br uits radioélectriques dépassant les limites applicables aux appareils num? ...

  • Cabletron Systems Expansion module 9E106-06 - page 6

    iv Notice ...

  • Cabletron Systems Expansion module 9E106-06 - page 7

    v Contents Chapter 1 Intr oduction Features........................................................................................................................... 1-2 Related Manuals ............................................................................................................ 1-5 Getting Help ..................................... ...

  • Cabletron Systems Expansion module 9E106-06 - page 8

    Contents vi Appendix A EPIMs EPIM-T ........................................................................................................................... A-1 EPIM-F1 and EPIM-F2 ................................................................................................. A-2 EPIM-F3 ........................................................ ...

  • Cabletron Systems Expansion module 9E106-06 - page 9

    1-1 Chapter 1 Intr oduction The 9E106-06 is a multi-port Ethernet Switch Module for the SmartSwitch 9000 that provides high speed IEEE 802.1D compliant bridging and Secur eFast™ Switching (SFS). Each 9E106-06 is equipped with two advanced Intel i960 ® RISC micropr ocessors. One processor pr ovides the module’s SNMP pr otocol stack for both IET ...

  • Cabletron Systems Expansion module 9E106-06 - page 10

    Introduction 1-2 Features Processor s The 9E106-06 is equipped with dual advanced Intel i960 ® RISC micropr ocessors. One processor pr ovides a platform for all management applications, such as Spanning T ree, RMON, IETF and Enterprise MIB support. This network management information is available through a variety of methods. All SNMP based inform ...

  • Cabletron Systems Expansion module 9E106-06 - page 11

    1-3 Introduction The FNB backplane connection is a fixed connection to FNB-1 or FNB-2. This connection allows the 9E106-06 to communicate with other SmartSwitch 9000 modules supporting various LAN technologies including: T oken Ring, FDDI, Ethernet, W AN and A TM. Bridging/SecureFast™ Switc hing 9E106-06 operates in two modes, as a traditional b ...

  • Cabletron Systems Expansion module 9E106-06 - page 12

    Introduction 1-4 Figure 1-1. The 9E106-06 SMB CPU 9E106-06 ETHERNET FNB ...

  • Cabletron Systems Expansion module 9E106-06 - page 13

    1-5 Introduction Related Manuals The manuals listed below should be used to supplement the procedur es and technical data contained in this manual. SmartSwitch 9000 Installation Guide SmartSwitch 9000 Operations Guide SmartSwitch 9000 9C300-1 Environmental Module User ’s Guide SmartSwitch 9000 9C214-1 AC Power Supply User ’s Guide SmartSwitch 9 ...

  • Cabletron Systems Expansion module 9E106-06 - page 14

    Introduction 1-6 ...

  • Cabletron Systems Expansion module 9E106-06 - page 15

    2-1 Chapter 2 Installing the 9E106-06 Module The 9E106-06 Module may be installed in any of the 14 slots available in the SmartSwitch 9000 chassis. T o install the 9E106-06 Module, follow the steps below: 1. Remove the blank panel covering the slot that the module is being mounted in. All other slots must be covered, if modules are not being instal ...

  • Cabletron Systems Expansion module 9E106-06 - page 16

    Installing the 9E106-06 Module 2-2 Figure 2-1. Installing the 9E106-06 Module Metal Back-Panel Module Guides Module Jack for ESD Wrist Strap Plastic Tab Ensure that the module is between the module guides. Lock down the top and bottom plastic tabs at the same time, applying even pr essur e. W ARNING ...

  • Cabletron Systems Expansion module 9E106-06 - page 17

    2-3 Installing the 9E106-06 Module Installing EPIMs This section contains procedur es on how to add/replace an Ethernet Port Interface Module (EPIM). After installing the EPIM, refer to Appendix A to verify proper EPIM operation. EPIM Revisions Revision numbers are located on the EPIM’s Printed Cir cuit Board directly following the Part Number as ...

  • Cabletron Systems Expansion module 9E106-06 - page 18

    Installing the 9E106-06 Module 2-4 Installing the EPIM T o install an EPIM: 1. Remove the coverplate or the EPIM (whichever applies). 2. Slide your new EPIM into place, making sure the connectors on the r ear of the module and inside the HUB attach properly . Refer to Figure 2-3. 3. Install the mounting screw . T able 2-1. EPIM Board Revisions EPIM ...

  • Cabletron Systems Expansion module 9E106-06 - page 19

    2-5 Installing the 9E106-06 Module Figure 2-3. Installing an EPIM The Reset Switch The Reset Switch is located on the front panel, under the top plastic tab, as shown in Figure 2-4. It serves two functions: • Pressing the Reset Switch twice within thr ee seconds resets the module. • Pressing and holding the switch on for thr ee or more seconds ...

  • Cabletron Systems Expansion module 9E106-06 - page 20

    Installing the 9E106-06 Module 2-6 Figure 2-4. The Reset Switch User -Accessible Components Figure 2-5 shows the various components that ar e accessible to the user . These consist of an eight-switch DIP switch (explained in the next section), r eplaceable PROMs and sockets for RAM. These will be used for future upgrades. Instructions for installin ...

  • Cabletron Systems Expansion module 9E106-06 - page 21

    2-7 Installing the 9E106-06 Module Figure 2-5. User-Accessib le Components Setting the Module Car d DIP Switch An eight-switch DIP switch is located on the module car d, as shown in Figure 2-5 and Figure 2-5. The functions of the switches ar e listed in T able 2-2. Flash SIMM Socket Packet DRAM Socket Local DRAM Socket Boot PROM Dip Switch SMB-1 PR ...

  • Cabletron Systems Expansion module 9E106-06 - page 22

    Installing the 9E106-06 Module 2-8 Figure 2-6. Location of Module DIP Switch 1 2 3 4 5 6 7 8 i 960 Boot PROM SMB-1 PROM ...

  • Cabletron Systems Expansion module 9E106-06 - page 23

    2-9 Installing the 9E106-06 Module See the Cautions at the end of this table. T able 2-2. Function of DIP Switch Switch Function Description 8 Clear Password -1 This module stores user enter ed passwords in NVRAM (Nonvolatile Random Access Memory). T o clear these passwords, toggle this switch and then r eset the module’s processor . Once the mod ...

  • Cabletron Systems Expansion module 9E106-06 - page 24

    Installing the 9E106-06 Module 2-10 ...

  • Cabletron Systems Expansion module 9E106-06 - page 25

    3-1 Chapter 3 Operation The 9E106-06 module is a seven port device, six front panel ports, each repr esenting a separate Ethernet collision domain, and one backplane connection to FNB-1 or FNB-2. As shown in Figure 3-1, packets r eceived through one of the six front panel Ethernet ports and destined for another SmartSwitch 9000 module are translate ...

  • Cabletron Systems Expansion module 9E106-06 - page 26

    Operation 3-2 System Management Buses There ar e two management channels within the SmartSwitch 9000 system: the SMB-1 and the SMB-10. These buses provide out-of-band management and inter - module management communication. SMB-1 Bus The SMB-1 is a 1Mbs management bus located within the SmartSwitch 9000. This bus is utilized by all diagnostic contro ...

  • Cabletron Systems Expansion module 9E106-06 - page 27

    3-3 Operation DC/DC Con ver ter The DC/DC converter converts the 48 VDC on the system power bus to the necessary operating voltages for its host network services module. The diagnostic controller monitors and contr ols the operation of the DC/DC converter . FNB Interface SmartSwitch 9000 modules are designed with one of two attachment policies. One ...

  • Cabletron Systems Expansion module 9E106-06 - page 28

    Operation 3-4 ...

  • Cabletron Systems Expansion module 9E106-06 - page 29

    4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. The 9E106-06 LANVIEW LEDs ar e shown in Figure 4-1. Figure 4-1. The LANVIEW LEDs SMB CPU 9E106-06 ETHERNET FNB FNB T ransmit Ether net Receiv e Ether net T ransmit FNB Receive System Status Diagnostic Controller St ...

  • Cabletron Systems Expansion module 9E106-06 - page 30

    LANVIEW LEDs 4-2 The functions of the System Management Bus (SMB) and CPU LEDs are listed in T able 4-1. The functions of the FNB Receive LED are listed in T able 4-1. The functions of the FNB T ransmit LED are listed in T able 4-3. T able 4-1. SMB and CPU LEDs LED Color State Description Green Functional Fully operational. Y ellow T esting Normal, ...

  • Cabletron Systems Expansion module 9E106-06 - page 31

    4-3 LANVIEW LEDs The functions of the Ethernet Receive LEDs are listed in T able 4-1. The functions of the Ethernet T ransmit LEDs are listed in T able 4-5. T able 4-4. Ethernet Receive LEDs LED Color State Green Link, No activity Y ellow (Flashing) Link, Activity (Flashing rate indicates rate of activity .) Red Port disabled no link Red (Flashing) ...

  • Cabletron Systems Expansion module 9E106-06 - page 32

    LANVIEW LEDs 4-4 ...

  • Cabletron Systems Expansion module 9E106-06 - page 33

    5-1 Chapter 5 Specifications T ec hnical Specifications CPU: Dual Intel i960 RISC based micropr ocessors Memory: 8 Meg. Local DRAM (expandable to 12 Meg.) 2 Meg. Flash Memory (expandable to 14 Meg.) 4 Meg. Shared DRAM (expandable to 12 Meg.) Netw ork Interfaces: Cabletron EPIMs Safety It is the responsibility of the person who sells the system to ...

  • Cabletron Systems Expansion module 9E106-06 - page 34

    Specifications 5-2 This equipment meets: The safety requir ements of: • UL 1950 • CSA C22.2 No. 950 • EN 60950 • IEC 950 The EMI Requirements of: • FCC Part 15 Class A • EN 55022 Class A • VCCI Class I The immunity requir ements of: • EN 50082-1 • IEC 801-2 ESD • IEC 801-3 Radiated susceptibility • IEC 801-4 EFT Service MTBF ...

  • Cabletron Systems Expansion module 9E106-06 - page 35

    A-1 Appendix A EPIMs The 9E106-06 Ethernet Switching Module provides one port per channel for Cabletron Systems EPIMs. EPIMs allow connecting to the 9E106-06 using differ ent media types. Cabletron Systems offers a variety of EPIMs whose specifications are explained in the following sections. EPIM-T The EPIM-T is an RJ-45 connector supporting UTP ...

  • Cabletron Systems Expansion module 9E106-06 - page 36

    EPIMs A-2 EPIM-F1 and EPIM-F2 The EPIM-F1 and EPIM-F2 support Multimode Fiber Optic cabling. Each EPIM has an internal Cabletron Systems FOT-F™ Fiber Optic Transceiver . The EPIM-F1 is equipped with SMA Connectors and the EPIM-F2 is equipped with ST Connectors. Figure A-2 shows both EPIMs. Specifications for the EPIMs are listed in T able A-1. T ...

  • Cabletron Systems Expansion module 9E106-06 - page 37

    A-3 EPIM-F3 EPIM-F3 The EPIM-F3 supports Single Mode Fiber Optic cabling. It has an internal Cabletron Systems FOT-F™ Fiber Optic Transceiver and is equipped with ST Connectors. Figure A-3 shows the EPIM-F3. Specifications for the EPIM-F3 are listed in T able A-3. The link distance is up to 40 kilometers (max) and 25 kilometers (typical) on sing ...

  • Cabletron Systems Expansion module 9E106-06 - page 38

    EPIMs A-4 EPIM-C The EPIM-C supports thin-net coaxial cabling and is equipped with an internal Cabletron Systems TMS-3™ Transceiver . Y ou can use the TERM switch on the front of the EPIM-C to set the internal 50-ohm terminator . This eliminates the need to connect the port to a tee-connector and terminator . Figure A-4 shows the setting for the ...

  • Cabletron Systems Expansion module 9E106-06 - page 39

    A-5 EPIM-A and EPIM-X (A UI P or t) The link distance is up to 185 meters on the thin-net coaxial cables. Figure A-4. EPIM-C Connector T ype This connector type is a BNC receptacle, with gold center contact, for use with BNC type tee-connectors and RG-58 thin-net cable. Gr ounding For safety reasons, only one end of a thin-net segment should be con ...

  • Cabletron Systems Expansion module 9E106-06 - page 40

    EPIMs A-6 Figure A-5. The EPIM-A and EPIM-X T able A-4 lists the DB-15 pinouts. T able A-4. DB-15 Pinouts Pin Number Represents Pin Number Represents 1 Logic Ref. 10 T ransmit - 2 Collision + 1 1 Logic Ref. 3 T ransmit 12 Receive - 4 Logic Ref. 13 Power (+12Vdc) 5 Receive 14 Logic Ref. 6 Power Return 15 No Connection 7 No Connection Connector Shell ...

Manufacturer Cabletron Systems Category Network Card

Documents that we receive from a manufacturer of a Cabletron Systems Expansion module 9E106-06 can be divided into several groups. They are, among others:
- Cabletron Systems technical drawings
- Expansion module 9E106-06 manuals
- Cabletron Systems product data sheets
- information booklets
- or energy labels Cabletron Systems Expansion module 9E106-06
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cabletron Systems Expansion module 9E106-06.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cabletron Systems Expansion module 9E106-06, service manual, brief instructions and user manuals Cabletron Systems Expansion module 9E106-06. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cabletron Systems Expansion module 9E106-06.

Similar manuals

A complete manual for the device Cabletron Systems Expansion module 9E106-06, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cabletron Systems Expansion module 9E106-06 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cabletron Systems Expansion module 9E106-06.

A complete Cabletron Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cabletron Systems Expansion module 9E106-06 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cabletron Systems Expansion module 9E106-06, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cabletron Systems Expansion module 9E106-06, that we can find in the current document
3. Tips how to use the basic functions of the device Cabletron Systems Expansion module 9E106-06 - which should help us in our first steps of using Cabletron Systems Expansion module 9E106-06
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cabletron Systems Expansion module 9E106-06
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cabletron Systems Expansion module 9E106-06 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cabletron Systems Expansion module 9E106-06?

Use the form below

If you did not solve your problem by using a manual Cabletron Systems Expansion module 9E106-06, ask a question using the form below. If a user had a similar problem with Cabletron Systems Expansion module 9E106-06 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)