English dropdown-ico

Manual Icom IC-R3

64 pages 1.5 mb
Download

Go to site of 64

Summary
  • Icom IC-R3 - page 1

    INSTRUCTION MANUAL This device complies with Part 15 of the FCC rules. Operation is sub- ject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. iR3 COMMUNICA TIONS RECEIVER ...

  • Icom IC-R3 - page 2

    i FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the receiver . SA VE THIS INSTRUCTION MANUAL — This in- struction manual contains important operating instructions for the IC-R3. EXPLICIT DEFINITIONS The explicit definitions below apply to this instruction manual. CAUTIONS R W ARNING! NEVER operate the receiver with a head- ...

  • Icom IC-R3 - page 3

    ii SUPPLIED ACCESSORIES Accessories included with the receiver: Qty . q Antenna (F A-B03RE) ...................................................... 1 w Belt clip ........................................................................... 1 e Battery spacer ................................................................ 1 r Battery pack* (BP-206) .. ...

  • Icom IC-R3 - page 4

    1 ACCESSOR Y A TT ACHMENT ............ 1 2 P ANEL DESCRIPTION .................. 2 – 6 ■ Panel description ............................. 2 ■ Function display ............................... 4 ■ Dual LCD ......................................... 6 3 FREQUENCY AND CHANNEL SETTING ....................................... 7 – 9 ■ VFO and mem ...

  • Icom IC-R3 - page 5

    1 1 ACCESSOR Y A TT ACHMENT ◊ Antenna Insert the supplied antenna into the an- tenna connector and screw down the an- tenna as shown at right. Keep the jack cover attached when jack is not in use to avoid bad contacts from dust and moisture. Commercially available antennas (BNC) may increase receiver performance. ◊ Battery installation q Remove ...

  • Icom IC-R3 - page 6

    ■ Panel description q ANTENNA CONNECTOR (p. 1) Connects the supplied antenna. w FUNCTION SWITCH [FUNC] While pushing this switch, other switches and tuning dial perform secondary functions. •“ Push [FUNC] + a switch ” means “ while pushing the [FUNC] switch, push the switch ” as indicated by the mark e.g. [ ↕ ] etc. e MUL TI FUNCTION ...

  • Icom IC-R3 - page 7

    3 2 P ANEL DESCRIPTION t VFO/MEMOR Y SWITCH [V/M (SKIP)] ➥ Push [V/M] to toggle between VFO and memory modes. (p. 7) ➥ Push [V/M] for 1 sec. to enter memory write mode. ➥ Push [V/M] for 2 sec. to write the operating frequency into the selected memory channel in VFO mode. Keep pushing for 2 sec. or more to automatically select the next memory ...

  • Icom IC-R3 - page 8

    4 2 P ANEL DESCRIPTION ■ Function display q RECEIVE MODE INDICA TORS (p. 12) Show the receive mode. • AM, FM and WFM are available. w DUPLEX INDICA TORS (p. 31) Appear when semi-duplex operation (repeater operation) is in use. •“ – DUP ” appears when minus duplex is selected; “ DUP ” only , ap- pears when plus duplex is selected. e ...

  • Icom IC-R3 - page 9

    5 2 P ANEL DESCRIPTION i SKIP SCAN INDICA T OR (pgs. 22, 24) ➥ “  ” appears when the selected memory channel is set as a skip channel in memory mode. ➥ “ P  ” shows that the skip frequency function is turned ON or OFF in VFO mode. ➥ “ P  ” appears when the selected memory channel is set to be skipped during VFO scan (full ...

  • Icom IC-R3 - page 10

    6 2 P ANEL DESCRIPTION ■ Dual LCD The receiver has dual LCDs for versatile display selection. The color LCD has 5 screens and 1 optional screen as fol - lows: simple, multi-function, band scope, direction fi nding, TV (fre- quency selection) and amateur TV* screen. * Amateur TV screen can be selected for the A TV -type and 1200/2400 MHz bands on ...

  • Icom IC-R3 - page 11

    7 3 FREQUENCY AND CHANNEL SETTING ■ VFO and memory channels This receiver has 2 normal operating modes: VFO mode and memory mode. VFO mode is used for setting a de- sired frequency within the fre- quency coverage. ➥ Push [V/M] to select VFO mode. Memory mode is used for opera- tion of memory channels which have programmed frequencies. ➥ Push ...

  • Icom IC-R3 - page 12

    8 3 FREQUENCY AND CHANNEL SETTING ■ Setting a frequency q Select the desired band with [ ↔ ]. w Rotate [DIAL] to change the frequency . • The frequency changes according to the preset tuning steps. See the right section for selecting the tuning step. • Some TV channels may be set as skip channels by default and can be selected by rotating [ ...

  • Icom IC-R3 - page 13

    9 3 FREQUENCY AND CHANNEL SETTING ■ Selecting a memory channel q Push [V/M] to select memory mode. •“ X ” or “ M: ” appears when a mem- ory channel is selected. w Rotate [DIAL] to change the indi- cated memory channel. • Only programmed memory chan- nels can be selected. • Rotate [DIAL] while pushing [FUNC] to change the memory bank ...

  • Icom IC-R3 - page 14

    10 4 BASIC OPERA TION ■ Receiving Make sure a charged battery pack or alkaline batteries are in - stalled. (pgs. 1, 46) q Push [POWER] for 2 sec. to turn power ON. w Push [ ↕ ] to set the desired audio level. • One of the LCDs shows the volume level while setting. See the next page for details. e Push [ ↔ ] to select an operating band. (p. ...

  • Icom IC-R3 - page 15

    11 4 BASIC OPERA TION ■ Setting volume level The audio level can be adjusted through 32 levels. ➥ Push [ ↕ ] to set the desired audio level. • Beep tone sounds while setting. This indicates the approximate sound level. (default behaviour; p. 40) • Pushing and holding these keys changes the audio level contin- uously . • One of the LCDs ...

  • Icom IC-R3 - page 16

    12 4 BASIC OPERA TION ■ Monitor function This function is used to listen to weak signals or to open the tone squelch manually . ➥ Push and hold [SQL] to monitor the operating frequency . •“ RX ” fl ashes while monitoring. The [SQL] switch can be set to ‘ sticky ’ operation in set mode. (p. 41) Y ou can monitor duplex communication by ...

  • Icom IC-R3 - page 17

    13 4 BASIC OPERA TION TV screens cannot be selected by pushing [MODE]. See p. 34 for TV operation details. ■ Display backlighting The receiver has display backlighting with a 5 sec. timer for nighttime operation. The display backlighting can be turned ON continuously or turned OFF , if desired. ➥ Push any switch except [FUNC]; or , rotate [DIAL ...

  • Icom IC-R3 - page 18

    ■ General The receiver has 400 memory channels in 8 banks (A – H) for storage of often-used frequencies. ◊ Memory channel contents The following information can be programmed into memory channels: • Operating frequency (p. 8) • Receive mode (p. 12) • T uning step (p. 8) • Memory name (p. 17) • Duplex direction (DUP or – DUP) with ...

  • Icom IC-R3 - page 19

    ■ Programming after selection q Select memory mode with [V/M]. w Set the memory channel to be programmed with [DIAL]. • Rotate [DIAL] while pushing [FUNC] to select a memory bank (A – H) or programmed scan edge channel. • Non-programmed channels cannot be selected. e Push [V/M] to select VFO mode. r Set the desired frequency: ➥ Select the ...

  • Icom IC-R3 - page 20

    ■ Memory bank selection The receiver has 400 memory channels in 8 banks (A – H) for storage of often-used frequencies. q Select memory mode with [V/M]. w Rotate [DIAL] while pushing [FUNC] to select the desired memory banks. e Rotate [DIAL] to select the desired memory channel. ■ Memory clear Unwanted memory channels can be cleared (erased). ...

  • Icom IC-R3 - page 21

    17 5 MEMORY CHANNELS ■ Memory names Each memory channel and scan edge channels can be pro- grammed with an alphanumeric name such as a repeater name, club name, etc., for easy recognition. Names can be a maximum of 6 characters — see the table at right for avail- able characters. The color LCD and memory names can be used when the op- erating f ...

  • Icom IC-R3 - page 22

    18 6 SCAN OPERA TION ■ Scan types Up to 25 programmed scan ranges (00A/00b to 24A/24b), full scan, band scan and memory bank scan provide scanning versatility . Each scan can have skip channels programmed. FULL SCAN (p. 19) Repeatedly scans all fre- quencies over the entire re- ceiver range. U.S.A. version cannot re- ceive some frequencies. PROGR ...

  • Icom IC-R3 - page 23

    19 6 SCAN OPERA TION ■ Full/band/programmed scan Scanning searches for signals automatically and makes it easier to locate new stations for listening purposes, etc. q Select VFO mode with [V/M]. w Make sure the squelch is set to the threshold point. • Select automatic squelch (AUT O) or a level (1 – 9) where the noise is just muted. (p. 10) e ...

  • Icom IC-R3 - page 24

    20 6 SCAN OPERA TION ■ Memory (bank) scan q Select memory mode with [V/M]. w For memory bank scan, rotate [DIAL] while pushing [FUNC] to select the desired memory bank. e Make sure the squelch is set to the threshold point. • Select automatic squelch (AUT O) or a level (1 – 9) where the noise is just muted. (p. 1 1) r Push and hold [ ↔ ], t ...

  • Icom IC-R3 - page 25

    21 6 SCAN OPERA TION ■ Selecting scan edges The scanning range can be set to all frequencies (full scan), a selected band (band scan) or between two user-programmed frequencies (programmed scan). The programmed scan edges can be programmed in the same manner as programming regular memory channels. Program the desired scan edge frequencies in a pa ...

  • Icom IC-R3 - page 26

    22 6 SCAN OPERA TION ■ Skip channel setting Memory channels can be set to be skipped for memory skip scan. In addition, memory channels can be set to be skipped for both memory skip scan and frequency skip scan. These are useful to speedup the scan interval. q Select memory mode with [V/M]. w Rotate [DIAL] to select a memory channel to be pro- gr ...

  • Icom IC-R3 - page 27

    23 6 SCAN OPERA TION e Push [ ↔ ] or rotate the tuning dial while pushing [FUNC] to select the desired scan pause time. •“ 2SEC ”–“ 20SEC ” : scan pauses for 2 – 20 sec. on a received sig- nal. •“ HOLD ” : scan pauses on a received signal until it dis- appears. r Push [(MODE) SET] to exit set mode. ◊ Setting the scan resume ...

  • Icom IC-R3 - page 28

    24 6 SCAN OPERA TION ■ Frequency skip function ◊ Programming a skip frequency Unwanted frequencies can be skipped and programmed as skip channels when full scan, band scan or programmed scan is pausing. q Start full scan, band scan or programmed scan. (p. 19) w While receiving an unwanted signal and scan pauses, push [FUNC] + [(V/M) SKIP] for 2 ...

  • Icom IC-R3 - page 29

    25 7 PRIORITY W A TCH ■ Priority watch types Priority watch checks for signals on a frequency every 5 sec. while operating on a VFO frequency or scanning. The re- ceiver has 3 priority watch types to suit your needs. In addition, you can be alerted with beeps and a fl ashing “ ë . ” The watch resumes according to the selected scan resume co ...

  • Icom IC-R3 - page 30

    26 7 PRIORITY W A TCH ■ Priority watch operation ◊ Memory channel watch and memory scan watch q Select VFO mode; then, set an operating frequency . w Set the watching channel(s). For memory channel watch: Select the desired memory channel. For memory scan watch: Select memory mode; then, push [ ↔ ] for 2 sec. to start memory scan. e Push [FUN ...

  • Icom IC-R3 - page 31

    ◊ VFO scan watch q Select the desired memory channel to be watched. w Push [V/M] to select VFO mode. e Push [ ↔ ] for 2 sec. to start full scan, band scan or pro- grammed scan. (p. 19) r Push [FUNC] + [(MODE) SET] momentarily to enter set mode. • Select a non-band scope screen in advance for color LCD. t Rotate [DIAL] to select “ Priority ? ...

  • Icom IC-R3 - page 32

    28 8 SUBAUDIBLE T ONE OPERA TION ■ T one squelch operation ◊ Operation The tone squelch opens only when receiving a signal con- taining a matching subaudible tone. Y ou can silently wait for calls from group members using the same tone in an ama- teur band. q Set the operating frequency in FM mode. w Set the desired subaudible tone in set mode. ...

  • Icom IC-R3 - page 33

    • Each operating band and each memory channel have indepen- dent settings. w Push [FUNC] + [(MODE) SET] momentarily to enter set mode. • Select a non-band scope screen in advance for color LCD. e Rotate [DIAL] until “ T one Freq. ” or “ tonE ” appears. •“ tonE ” disappears after 1 sec. and “ Ct ” appears. r Push [ ↔ ] or rot ...

  • Icom IC-R3 - page 34

    30 8 SUBAUDIBLE TONE OPERA TION t Rotate [DIAL] until “ T one Squelch ” or “ tSqL ” appears. •“ tSqL ” disappears after 1 sec. and “ to ” appears when color LCD is OFF . y Push [ ↔ ] or rotate the tuning dial while pushing [FUNC] to select “ P BEEP ” (pocket beep). u Push [(MODE) SET] to exit set mode and start the pocket be ...

  • Icom IC-R3 - page 35

    31 9 DUPLEX OPERA TION Duplex communication uses 2 different frequencies for trans- mitting and receiving. Generally , duplex is used in communi- cation through a repeater , some utility communications, etc. During duplex operation, the transmit station frequency is shifted from the receive station frequency by the of fset fre- quency . Repeater in ...

  • Icom IC-R3 - page 36

    32 9 DUPLEX OPERA TION ◊ Offset frequency During duplex operation, the transmit station frequency is shifted from the receive station frequency by an amount de- termined by the offset frequency . q Select VFO mode or desired memory channel to be pro- grammed. w Push [FUNC] + [(MODE) SET] momentarily to enter set mode. • Select a non-band scope ...

  • Icom IC-R3 - page 37

    33 10 BAND SCOPE The band scope function allows you to visually check a spec- i fi ed frequency range. Sweep range can be selected from ± 5 kHz through ± 500 kHz. Receive audio is muted while monitoring the band scope. Push [SQL] to cancel sweeping and receive the audio. q Push [FUNC] + [ ↕ ] for 2 sec. to turn the color LCD ON. w Push [FUNC] ...

  • Icom IC-R3 - page 38

    34 11 TV OPERA TION ■ TV operation The receiver can receive TV (NTSC or P AL depending on ver- sion). TV channels are preset depending on versions. The received video and audio can be output from [A/V OUT] if desired. ◊ TV channel receiving q Push [FUNC] + [ ↕ ] for 2 sec. to turn the color LCD ON, if desired. • Only the audio part of the T ...

  • Icom IC-R3 - page 39

    35 11 TV OPERA TION ◊ TV frequency (AM TV) receiving Y ou can set the TV frequency instead of channel selection, if desired. q Push [FUNC] + [ ↕ ] for 2 sec. to turn the color LCD ON, if desired. • The audio part of the TV contents can be received when the color LCD is turned OFF . w Push [ ↔ ] one or more times to select the band above 30 ...

  • Icom IC-R3 - page 40

    36 11 TV OPERA TION ■ A TV operation The IC-R3 A TV -type can receive an amateur TV (FM TV) within 900 – 1300 and 2250 – 2450.095 MHz. The received video and audio can be output from [A/V OUT] if desired. (p. 5) q Push [FUNC] + [ ↕ ] for 2 sec. to turn the color LCD ON, if desired. • Only the audio part of the TV contents can be received. ...

  • Icom IC-R3 - page 41

    37 12 DIRECTION FINDING The direction fi nding function allows you to check a variation of the signal level continuously . Using a commercially available directional antenna, you can determine the direction of the signal source. Using 2 receivers with the directional antennas, you can pinpoint the signal source. q Push [FUNC] + [ ↕ ] for 2 sec. ...

  • Icom IC-R3 - page 42

    38 13 OTHER FUNCTIONS ■ Set mode Set mode is used for programming infrequently changed val- ues or conditions of functions. ◊ Set mode items L : Appears when the color LCD is ON. T : Appears when receiving TV . B : Does not appear within the broadcast band (0.495 – 1.620 MHz) except for U.S.A. and Canada versions Tone squelch (p. 28) Tone squ ...

  • Icom IC-R3 - page 43

    39 13 OTHER FUNCTIONS ■ Dial select step This receiver has a 1 MHz tuning step for quick frequency setting. This dial select step can be set to 100 kHz, 1 MHz or 10 MHz steps, as desired. The selected dial select step is always displayed in the sim- ple, multi-function and direction finding screen in the color LCD. This function is not available ...

  • Icom IC-R3 - page 44

    40 13 OTHER FUNCTIONS ■ Beep tones The volume level for con fi rmation beep tones, which sound each time a switch is pushed, can be adjusted, as desired. When “ VOLUME ” is selected, the beep tone volume level is linked with the receive volume level. q Push [FUNC] + [(MODE) SET] momentarily to enter set mode. • Select a non-band scope scre ...

  • Icom IC-R3 - page 45

    41 13 OTHER FUNCTIONS ■ Power saver The power saver function reduces the current drain to con- serve battery power . q Push [FUNC] + [(MODE) SET] momentarily to enter set mode. • Select a non-band scope screen in advance for color LCD. w Rotate [DIAL] until “ Power Save ” or “ PS A V E ” appears. •“ PS A V E ” disappears after 1 s ...

  • Icom IC-R3 - page 46

    42 13 OTHER FUNCTIONS ■ Dial speed acceleration The dial speed acceleration automatically speeds up the tun- ing dial speed when rotating the [DIAL] rapidly . q Push [FUNC] + [(MODE) SET] momentarily to enter set mode. • Select a non-band scope screen in advance for color LCD. w Rotate [DIAL] until “ Dial Speedup ” or “ SPEEd ” appears. ...

  • Icom IC-R3 - page 47

    43 13 OTHER FUNCTIONS ■ Display mode selection The color LCD can be automatically turned ON when using with the external DC power (CP-18A/E or commercially available DC power supply; 5.5 – 6.3 V DC with more than 4 A capacity) . q Push [FUNC] + [(MODE) SET] momentarily to enter set mode. • Select a non-band scope screen in advance for color L ...

  • Icom IC-R3 - page 48

    44 13 OTHER FUNCTIONS ■ Display brightness This item adjusts the brightness of the color LCD from 0 % to 100 % in 32 steps. q Push [FUNC] + [ ↕ ] for 2 sec. to turn the color LCD ON. w Push [FUNC] + [(MODE) SET] momentarily to enter set mode. • Select a non-band scope screen in advance. e Rotate [DIAL] until “ Bright ” appears. •“ bRI ...

  • Icom IC-R3 - page 49

    45 13 OTHER FUNCTIONS ■ Cloning function The IC-R3 has receiver-to-receiver data cloning capability . This function is useful when you want to copy all of the pro- grammed contents from one IC-R3 to another . An optional OPC-474 CLONING CABLE is required. The optional CS-R3 CLONING SOFTW ARE and the optional OPC-478 CLONING CABLE are available to ...

  • Icom IC-R3 - page 50

    ■ Battery cautions NEVER incinerate used battery packs. Internal battery gas may cause an explosion. NEVER immerse the battery pack in water . If the battery pack becomes wet, be sure to wipe it dry BEFORE attaching it to the receiver . NEVER short terminals of the battery pack. Also, current may fl ow into nearby metal objects so be careful whe ...

  • Icom IC-R3 - page 51

    47 14 BA TTER Y CHARGING ◊ Regular charging q Attach the battery pack to the receiver . w Be sure to turn the receiver power OFF . e Connect the AC adapter (BC-136A/D*) or optional cable (CP-18A/E) as shown below . * Not supplied with some versions. r Remove any cables from the [DC 6V] jack. • Charging periods: 15 hours (w/BP-206) ◊ CP-18A/E ...

  • Icom IC-R3 - page 52

    48 15 OPERA TION FLOW CHART MODE SET V/M SKIP V/M SKIP FM P MODE SET MODE SET momentarily momentarily MODE SET FUNC + VFO mode Memory mode Program scan starting menu (p. 19) Bank scan starting menu (p. 20) Tuning step set mode (p. 8) ( ) for 2 sec. for 2 sec. for 2 sec. ( ) for 2 sec. 0.495–1.620 MHz 1.625–29.995 MHz 30.0–75.995 MHz 76.0–10 ...

  • Icom IC-R3 - page 53

    49 15 OPERA TION FLOW CHAR T Tone squelch (p. 28) Tone squelch tone frequency (p. 28) B Duplex direction (p. 31) B Offset frequency (p. 32) Scan resume time (p. 23) Scan pause time (p. 22) Priority watch (p. 26) Confirmation beep (p. 40) Backlighting (p. 13) Auto power OFF (p. 40) Power save (p. 41) Monitor switch action (p. 41) Dial speed (p. 42) ...

  • Icom IC-R3 - page 54

    The following tables show the channels versus video and audio frequencies depending on each version. ■ U.S.A. channels ■ CCIR channels 50 16 TV FREQUENCY T ABLE CH Video Audio 2 55.25 59.75 3 61.25 65.75 4 67.25 71.75 5 77.25 81.75 6 83.25 87.75 7 175.25 179.75 8 181.25 185.75 9 187.25 191.75 10 193.25 197.75 1 1 199.25 203.75 12 205.25 209.75 ...

  • Icom IC-R3 - page 55

    ■ Australian channels CH Video Audio 39 604.25 609.75 40 61 1.25 616.75 41 618.25 623.75 42 625.25 630.75 43 632.25 637.75 44 639.25 644.75 45 646.25 651.75 46 653.25 658.75 47 660.25 665.75 48 667.25 672.75 49 674.25 679.75 50 681.25 686.75 51 688.25 693.75 52 695.25 700.75 53 702.25 707.75 54 709.25 714.75 55 716.25 721.75 56 723.25 728.75 57 7 ...

  • Icom IC-R3 - page 56

    52 16 TV FREQUENCY T ABLE ■ China channels CH Video Audio 1 49.75 56.25 2 57.75 64.25 3 65.75 72.25 4 77.25 83.75 5 85.25 91.75 6 168.25 174.75 7 176.25 182.75 8 184.25 190.75 9 192.25 198.75 10 200.25 206.75 1 1 208.25 214.75 12 216.25 222.75 13 471.25 477.75 14 479.25 485.75 15 487.25 493.75 16 495.25 501.75 17 503.25 509.75 18 51 1.25 517.75 1 ...

  • Icom IC-R3 - page 57

    53 16 TV FREQUENCY T ABLE ■ FOT channels CH Video Audio 4 175.25 181.75 5 183.25 189.75 6 191.25 197.75 7 199.25 205.75 8 207.25 213.75 9 215.25 221.75 CH Video Audio 64 815.25 820.75 65 823.25 828.75 66 831.25 836.75 67 839.25 844.75 68 847.25 852.75 69 855.25 860.75 ■ Italian channels CH Video Audio A* 53.75 59.25 B* 62.25 67.75 C* 82.25 87.7 ...

  • Icom IC-R3 - page 58

    54 17 SPECIFICA TIONS AND OPTIONS ◊ General • Frequency coverage : (unit: MHz) U.S.A. version 0.495 – 815.995, 902 – 2450.095 Non-U.S.A. versions 0.495 – 2450.095 • Mode : FM, AM, WFM, AM-TV ,* 1 FM-TV ,* 2 * 1 One of either NTSC M, P AL B or P AL G systems. * 2 For 900 – 1300 MHz and 2250 – 2450 MHz ranges only; not available in so ...

  • Icom IC-R3 - page 59

    55 17 SPECIFICA TIONS AND OPTIONS AM (at 10 dB S/N) 0.495 – 4.995 MHz 1.4 µV 5.0 – 29.995 MHz 1.0 µV 11 8 – 136.000 MHz 0.79 µV 222 – 329.995 MHz 1.0 µ V • Selectivity : FM, AM More than 12 kHz/ – 6 dB Less than 30 kHz/ – 50 dB WFM More than 150 kHz/ – 6 dB • Audio output power : 100 mW typical at 10% (at 4.5 V DC) distortion ...

  • Icom IC-R3 - page 60

    56 18 TROUBLESHOOTING PROBLEM POSSIBLE CA USE SOLUTION REF . No power comes ON. • The batteries are exhausted. • The battery polar ity is rev ersed. • Replace the batteries or charge the batter y pack. • Check the battery polarity . pgs. 1, 46 p. 1 No sound comes from the speaker . • V olume lev el is too low . • The squelch lev el is s ...

  • Icom IC-R3 - page 61

    OPERA TING GUIDE iR3 ■ B ASIC OPERA TION q Push [POWER] f or 2 sec. w Push [ ↕ ] to set the desired audio lev el. e Select VFO mode with [V/M]. r Select the desired band with [ ↔ ]. t Rotate [DIAL] to change the fre- quency . • The frequency changes according to the preset tuning steps. y Set the squelch lev el. • While pushing [SQL], rot ...

  • Icom IC-R3 - page 62

    58 19 QUICK REFERENCE ■ SCAN ◊ Full/band/programmed scan q Select VFO mode with [V/M]. w Make sure the squelch is set to the threshold point. e P ush [ ↔ ] for 2 sec. to start the scan. • Rotate [DIAL] while pushing [ ↔ ] to select scan edge, if desired. • T o change the scanning direction, ro- tate [DIAL]. r Push [ ↔ ] again to stop ...

  • Icom IC-R3 - page 63

    DECLARATION OF CONFORMITY We Icom Inc. Japan 6-9-16, Kamihigashi, Hirano-ku Osaka 547-0002, Japan Type-designation: iC-r3 Version (where applicable): Kind of equipment: COMMUNICATIONS RECEIVER This compliances is based on conformity with the following harmonised standards, specifications or documents: i) EN 60950 ii) prEN 301 489-1 iii) prEN 301 48 ...

  • Icom IC-R3 - page 64

    Count on us! 6-9-16 Kamihigashi, Hirano-ku, Osaka 547-0002 Japan A-5653H-1EX- w Printed in Japan © 2000 Icom Inc. ...

Manufacturer Icom Category Car Satellite TV System

Documents that we receive from a manufacturer of a Icom IC-R3 can be divided into several groups. They are, among others:
- Icom technical drawings
- IC-R3 manuals
- Icom product data sheets
- information booklets
- or energy labels Icom IC-R3
All of them are important, but the most important information from the point of view of use of the device are in the user manual Icom IC-R3.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Icom IC-R3, service manual, brief instructions and user manuals Icom IC-R3. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Icom IC-R3.

Similar manuals

A complete manual for the device Icom IC-R3, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Icom IC-R3 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Icom IC-R3.

A complete Icom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Icom IC-R3 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Icom IC-R3, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Icom IC-R3, that we can find in the current document
3. Tips how to use the basic functions of the device Icom IC-R3 - which should help us in our first steps of using Icom IC-R3
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Icom IC-R3
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Icom IC-R3 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Icom IC-R3?

Use the form below

If you did not solve your problem by using a manual Icom IC-R3, ask a question using the form below. If a user had a similar problem with Icom IC-R3 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)