English dropdown-ico

Manual Pelco c2462m-e

24 pages 1.09 mb
Download

Go to site of 24

Summary
  • Pelco c2462m-e - page 1

    INST ALLA TION C2462M-E (3/09) 090 Series Camclosure ® Indoor Integrated Camera System Surface Mount/In-Ceiling ...

  • Pelco c2462m-e - page 2

    2 C2462M-E (3/09) Contents Important Safety Instructi ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Descripti ...

  • Pelco c2462m-e - page 3

    C2462M-E (3/09) 3 List of Illustrations 1 Removing the Dome Bubble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Ceiling/W all In stallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 Concrete Ceilin ...

  • Pelco c2462m-e - page 4

    4 C2462M-E (3/09) Important Safety Instructions 1. Installation and servicing should be d one only by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and must not be installed where exposed to rain and moist ...

  • Pelco c2462m-e - page 5

    C2462M-E (3/0 9) 5 Description The ICS090 Series Camclosure ® integrated camera system integrates a camera and lens package in a small, discreet dome. The system is easy to install and can be mounted or recessed to the surface of a ceiling or wall. Prior to the installation of your n ew system, thoroughly familiarize yourself with the information ...

  • Pelco c2462m-e - page 6

    6 C2462M-E (3/09) Remove the Dome Bubble T urn the dome bubble counterclockwise and lift (refer to Figure 1 ). Place the bubble on a non abrasive surface. Figure 1. Removing the Dome Bubb le If the unit is supplied with a dome liner , remove the li n er before installing the unit. T o remove the liner , gently lift it from the unit. Place t he line ...

  • Pelco c2462m-e - page 7

    C2462M-E (3/0 9) 7 Installation The installation methods for the ICS090 Series include the following options: • Mount to the surface of a ceiling or wall • Install in a suspended ceiling • Install in a fixed ceiling or wall • Mount to the surface of a 4S standard electrical bo x • Install in a 4S deep electrica l box SURFACE INSTALLATION: ...

  • Pelco c2462m-e - page 8

    8 C2462M-E (3/09) 4. Use 6-32 toggle bolts (not supplied) to attach the surface mount ring and back box to the mounting surface (refer to Figure 2 ). Figure 3. Concrete Ceiling/W all Installation Figure 2. Ceiling/Wall Installati on NOTE: For a concrete ceiling or wall installation, use 8-32 mounting hardware (not supplied), ref er to Figure 3. ...

  • Pelco c2462m-e - page 9

    C2462M-E (3/0 9) 9 IN-CEILING INSTALLATION: SUSPENDED CEILING 1. Remove the ceiling tile from the ceiling (refer to Figure 4 ). 2. Cut a 4-inch diameter h ole in the ceiling tile. 3. Remove the surface mount ring from the back box (refer to Figure 5 on page 10 ): a. Place your fingers on the circular marks loca ted on the s ides of the surface moun ...

  • Pelco c2462m-e - page 10

    Figure 5. How to Remove Surfac e Mount Ring from Back Box 10 C2462M-E (3/09) AC operation only: If you are wiring more than one Camclosure to the same transformer , connect one side of the transformer to the red wire on all uni ts; connect the other side of the transformer to the black wire on all units. NOTE: Failure to connect all of the units in ...

  • Pelco c2462m-e - page 11

    C2462M-E (3/0 9) 11 IN-CEILING INSTALLATION: FIXED CEILING OR WALL 1. Cut a 4-inch diameter h ole in the ceiling/wall (refer to Figure 6 on p age 11 ). 2. Remove the surface mount ring from the back box (refer to Figure 5 on page 10 ). a. Place your fingers on the circular marks loca ted on the s ides of the surface mount ring. b. Pinch the sides. ...

  • Pelco c2462m-e - page 12

    12 C2462M-E (3/09) SURFACE INSTALLATION: 4S STANDARD ELECTRICAL BOX 1. Attach the adapter ring to the 4S box with tw o 8-32 x 1.00-inch screws (supplied; refer to Figure 7 ). 2. Connect the video cable and wires. BNC: Connect the BNC connector from the Camclosure to a mating BNC connector . T wisted pair: Connect the blue wire to Video +; c onnect ...

  • Pelco c2462m-e - page 13

    C2462M-E (3/0 9) 13 IN-CEILING INSTALLATION: 4S DEEP ELECTRICAL BOX 1. Remove the surface mount ring from the back box (refer to Figure 8 ): a. Place your fingers on the circular marks loca ted on the s ides of the surface mount ring. b. Pinch the sides. c. Lift and remove the surface mount ring from the back box. 2. Attach the adapter ring to the ...

  • Pelco c2462m-e - page 14

    14 C2462M-E (3/09) Camera Positioning Figure 9. Positioning the Camera Manually rotate and tilt the came ra module to position th e camera. Do not over-rot ate the module. WAR NI NG : E xcessively turning the module in one direct ion could result in damage to the wiring.    ì T ilt 140° (20° to 160°) î Pan 360° ï Rotation 360° ...

  • Pelco c2462m-e - page 15

    C2462M-E (3/0 9) 15 Camera Adjustments SWITCH SETTINGS FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to the switch drawing. The switch is located n ext to the lens. Automatic backlight compensation (factory setting) is used under va ry ing lighting conditions (suc h as ou tdoors) or fixed lighting con ditions where there are no bright spots that ...

  • Pelco c2462m-e - page 16

    16 C2462M-E (3/09) FOCUS ADJUSTMENT NOTE: Y o u will need a miniature Phillips or flat-tip screw driver to loosen and tighten the locking screw. T o adjust the fo cus: 1. Loosen the focus locking screw . 2. Position the inverted dome appro ximately 0.125 inch (3.175 mm) from the front of the lens. Make sure that the len s and the dome are centered ...

  • Pelco c2462m-e - page 17

    C2462M-E (3/0 9) 17 V ERTICAL PHASE ADJUSTMENT (24 V ac Operation Only) When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera view is switched. T o elim inate vertica l roll, reverse the 24 V AC connections on one camera. If both cameras are connected to the same transformer , this should solve t ...

  • Pelco c2462m-e - page 18

    18 C2462M-E (3/09) Install Liner and Bubble DOME LINER INSTALLATION If the unit is supplied with a dome liner , reinstall th e liner be fore installing the dome bubble (refer to Figure 13 ): 1. Align the studs located on the camera module with the clips on the liner . 2. Lightly pinch the sides of the liner , opposite fro m the clips, and place the ...

  • Pelco c2462m-e - page 19

    C2462M-E (3/0 9) 19 DOME BUBBLE INSTALLATION T o install the d ome bubble (refer to Figure 14 ): 1. Select the bubble (clear or smoked). 2. Align the standoffs of the bubble with the slots of the back box. Figure 14. Installing the Dome Bubble 3. T urn the bubble clockwise until it locks in place. ...

  • Pelco c2462m-e - page 20

    20 C2462M-E (3/09) Service Connector An optional 4-foot service/monitor cable, part numb er ICS090-SC, is available for on- site setup and adjustments. T o use the cable, simply plug one end of the cable directly into the service connector of the ICS090, and then connect the other end to any st andard BNC (VIDEO IN) connector on a monitor . T o ass ...

  • Pelco c2462m-e - page 21

    C2462M-E (3/09) 21 Specifications ELECTRICAL Input V oltage* 12 VDC or 24 V AC (±10%), autosensing Power Consumption 3 W or less Video Connector BNC *24 V AC power is recommended when installing any Camclosure integrated camera system under fluorescent lighting conditions. GENERAL Pan/T ilt Adjustment Pan 360° T ilt 140° (20° to 160° range) Ro ...

  • Pelco c2462m-e - page 22

    22 C2462M-E (3/09) REVISION HISTORY Manual # Date Comments C2462M 11/02 Original version. C2462M-A 1/03 Added Regulatory Noti ces for FCC Class B. C2462M-B 10/05 Revised switch-set ting descript ions for vari focal lens. Adde d WEEE statement. C2462M-C 1/06 Updated factory sw itch setting s for varifo cal lens per ECO 13164. Updated w iring informa ...

  • Pelco c2462m-e - page 23

    The materials us ed in the manufactu re of this documen t and its component s are compliant to th e requirement s of Directive 20 02/95/EC. This equipment co ntains electr ical or electron ic components t hat must be rec ycled properly to comply with Dir ective 2002/96/EC of the European Union re garding the disp osal of waste electrical and elec t ...

  • Pelco c2462m-e - page 24

    Pelco, Inc. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .pelco.com ...

Manufacturer Pelco Category Camera Accessories

Documents that we receive from a manufacturer of a Pelco c2462m-e can be divided into several groups. They are, among others:
- Pelco technical drawings
- c2462m-e manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco c2462m-e
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco c2462m-e.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco c2462m-e, service manual, brief instructions and user manuals Pelco c2462m-e. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco c2462m-e.

Similar manuals

A complete manual for the device Pelco c2462m-e, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco c2462m-e by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco c2462m-e.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco c2462m-e - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco c2462m-e, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco c2462m-e, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco c2462m-e - which should help us in our first steps of using Pelco c2462m-e
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco c2462m-e
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco c2462m-e in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco c2462m-e?

Use the form below

If you did not solve your problem by using a manual Pelco c2462m-e, ask a question using the form below. If a user had a similar problem with Pelco c2462m-e it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)