English dropdown-ico

Manual Fujitsu ScanPartner 620C

26 pages Not applicable
Download

Go to site of 26

Summary
  • Fujitsu ScanPartner 620C - page 1

    ScanPartner 620C Image Scanner User's Manual (Doc. No. 250-0062-0 Ver. 1.0) ...

  • Fujitsu ScanPartner 620C - page 2

    ii FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate ra ...

  • Fujitsu ScanPartner 620C - page 3

    iii Table of Contents 1. INTRODUCTION ........................................................................................... 1-1 2. INSTALLATION ............................................................................................ 2-1 2.1 SHIPPING BRACKET .................................................................................. ...

  • Fujitsu ScanPartner 620C - page 4

    1-1 1. INTRODUCTION Congratulations on your purchase of Fujitsu ScanPartner 620C Scanner. Before you install and operate the new Scanner, please take a few minutes to read through this manual. It provides you with the proper instructions on how to unpack, install, operate and maintain the Scanner. Figure 1-1 shows how the Scanner is packed. You can ...

  • Fujitsu ScanPartner 620C - page 5

    2-1 2. INSTALLATION Please unpack the Scanner carefully, and check the contents against the c hecklist. If any items are missing or damaged, please contact your authorized local dealer immediately. Precautions • Keep the Scanner out of direct sunlight. Direct exposure to the sun or excessive heat may cause damage to the unit. • Do not install t ...

  • Fujitsu ScanPartner 620C - page 6

    2-2 Figure 2-1 Removing the Shipping Bracket Figure 2-2 Securing the Shipping Bracket “Use Position” “Shipping Position” ...

  • Fujitsu ScanPartner 620C - page 7

    2-3 2. 1 .2 REFITTING THE SHIPPING BRACKET Whenever you need to move the Scanner to a new location it is advisable to refit the shipping bracket to avoid causing damage to the Scanners’ internal mechanism. Please follow the instructions below to refit the shipping bracket. i). Turn off the Scanner power at the power on/off switch. ii). Open the d ...

  • Fujitsu ScanPartner 620C - page 8

    2-4 Figure 2-3 Adjusting the SCSI ID setting. SCSI ID Selector SCSI Termination Switch On Off ...

  • Fujitsu ScanPartner 620C - page 9

    2-5 2. 3 ADF PAPER CHUTE i). Raise the right side of the paper chute to about 45 degrees. ii). Pull down the wire leg from under the paper chute . iii). Insert the wire leg into the grips on the document cover . iv). Pull out the paper chute extension to the length you want. Figure 2-4 Setting the ADF Paper Chute ADF Paper Chute Document Cover Pape ...

  • Fujitsu ScanPartner 620C - page 10

    2-6 2. 4 ADF OUTPUT TRAY i). Hold the output paper tray some 30 degrees aslant as shown in Figure 2-5. ii). Insert the three protrusions on the output paper tray to the three slots on the ADF. iii). Release the paper tray gently. Make sure the tray is firmly attached to the ADF. iv). Pull out the output paper tray extension wire to the desired leng ...

  • Fujitsu ScanPartner 620C - page 11

    2-7 2. 5 DOCUMENT LOADING For flatbed scanning Documents that can not be scanned using the ADF can be placed on the flatbed for scanning. (See Figure 2-6) i). Place the document to be scanned onto the document glass face down. ii). Position the document so that the upper-right corner is aligned with the reference mark . Figure 2-6 Place Document on ...

  • Fujitsu ScanPartner 620C - page 12

    2-8 2. 6 ADF SCANNING Standard paper size can be scanned automatically using the ADF. Refer to Figure 2-7. i). To prevent occasional paper jam when automatically feeding multiple documents, fan the paper before loading. ii). Lift the balance wire and place the documents to be scanned onto the ADF paper chute face down, with the leading edge in the ...

  • Fujitsu ScanPartner 620C - page 13

    2-9 2. 7 CONNECTING THE CABLE i). Turning the Power Off Depress the side marked “O” to turn the power off. Connect the power cable and SCSI signal cable as shown in Figure 2-8 and Figure 2-9. ii). Turning the Power On Depress the side marked “I” to turn the power on. The POWER LED will light. If not, please check the power source. iii). SCS ...

  • Fujitsu ScanPartner 620C - page 14

    2-10 Figure 2-8 ScanPartner 620C Power Cable Connection Figure 2-9 ScanPartner 620C SCSI Cable Connection SCSI Cable Connector Power Cable To PC SCSI Port Power Switch SCSI Port ...

  • Fujitsu ScanPartner 620C - page 15

    3-1 3. MAINTENANCE 3. 1 CLEANING THE ADF Your Scanner is designed to be maintenance free. However, it still needs to be cleaned occasionally to ensure optimum image quality and performance. From time to time the pad assembly and feeding rollers may become contaminated with ink, toner particles or paper dust. In this case the scanner may not feed do ...

  • Fujitsu ScanPartner 620C - page 16

    3-2 Figure 3-1 Opening the ADF unit and Document Cover Feeding Roller ADF Pad Module ¬ ¬ - - ...

  • Fujitsu ScanPartner 620C - page 17

    3-3 3. 2 CLEANING THE GLASS The procedures: i). Soak a cotton swab with some isoprophy alcohol (95%). ii). Open the ADF unit and document cover as shown in Figure 6-2. Wipe the glass of flatbed area and ADF area by moving the swab from side to side. iii). Close the ADF unit and document cover. Your Scanner is now ready for use. Figure 3-2 The Clean ...

  • Fujitsu ScanPartner 620C - page 18

    3-4 3. 3 REPLACING THE ADF SNAP-IN PAD MODULE After scanning approximately 150,000 pages through the ADF, the pad spring may be worn out and you may experience problems with document feeding. In this case, it is highly recommended to replace the pad module with a new one. For ordering the pad module, please consult your nearest dealer and follow th ...

  • Fujitsu ScanPartner 620C - page 19

    3-5 Assembling Procedure 1. Take out the ADF pad module from the box. 2. Hold the upper part of the pad clamp and place it gently to the pad holder as shown in Figure 3-4. Figure 3-4 Installing the pad module ADF Pad Module Upper Part of the Pad Clamp ...

  • Fujitsu ScanPartner 620C - page 20

    4-1 4. TROUBLESHOOTING The Scanner will automatically perform a simple self-test each time it is turned on. This will help spot major system errors in the Scanner itself. When the test is initiated, the READY LED is flashing. When the test is completed, if no error occur, the READY LED is steadily on. If you have problems with the operation of your ...

  • Fujitsu ScanPartner 620C - page 21

    4-2 Question: Paper becomes skewed in the Scanner. Answer: a) Check the feeding roller condition; do the cleaning if necessary. (See Section 3.1) b) Use the paper guide when feeding the p aper. Question: When I power on the Scanner, it makes noises and will not stand ready. Answer: There are two possibilities: a) You forgot to remove the shipping r ...

  • Fujitsu ScanPartner 620C - page 22

    4-3 Question: While scanning, the Scanner often makes noises, or it scans back and forth. Answer: Please choose lower speed from the TWAIN user interface for low speed PC. Question: The scanned image always comes out to be too dark. Answer: a) Use your application to modify the Gamma setting to 2.2 and 1.8 for your printer and monitor respectively. ...

  • Fujitsu ScanPartner 620C - page 23

    4-4 Figure 4-2 ADF Paper Jam - Removing the Paper ADF Paper Chute Document ADF Unit ...

  • Fujitsu ScanPartner 620C - page 24

    5-1 5. SPECIFICATIONS All specifications are subject to change without notice. The following can not be properly fed by ADF: • Paper with clip or staple attached; • Paper with ink not totally dry; • Paper with inconsistent thickness, such as envelopes; • Paper with wrinkles, curls, folds or tears; • Tracing paper; • Coated paper; • Ca ...

  • Fujitsu ScanPartner 620C - page 25

    5-2 5. 1 SCANPARTNER 620C SPECIFICATIONS Scanner Type v 1-pass colour v Flatbed with ADF built-in Scanning Mode v 36-bit colour v 12-bit Grey Scale v Line Art/Halftone v Error Diffusion (single bit) Optical Resolution v 600 x 1200 dpi in a dpi increments Light Source v Cold Cathode fluorescent lamp ADF Capacity v 50 pages ADF Scanning Speed v 20 PP ...

  • Fujitsu ScanPartner 620C - page 26

    a Index A ADF cover · 4-3 ADF Scanning · 2-8 B balance wire · 2-8 C Cleaning the ADF · 3-1 Cleaning the Glass · 3-3 Connecting the Cable · 2-9 D document cover · 2-5 Document Loading · 2-7 O output paper tray · 2-6 output paper tray extension · 2-6 P paper chute · 2-5 paper chute extension · 2-5 paper jam · 2-8, 4-3 POWER LED · 2-9 pr ...

Manufacturer Fujitsu Category Scanner

Documents that we receive from a manufacturer of a Fujitsu ScanPartner 620C can be divided into several groups. They are, among others:
- Fujitsu technical drawings
- ScanPartner 620C manuals
- Fujitsu product data sheets
- information booklets
- or energy labels Fujitsu ScanPartner 620C
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fujitsu ScanPartner 620C.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fujitsu ScanPartner 620C, service manual, brief instructions and user manuals Fujitsu ScanPartner 620C. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fujitsu ScanPartner 620C.

Similar manuals

A complete manual for the device Fujitsu ScanPartner 620C, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fujitsu ScanPartner 620C by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fujitsu ScanPartner 620C.

A complete Fujitsu manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fujitsu ScanPartner 620C - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fujitsu ScanPartner 620C, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fujitsu ScanPartner 620C, that we can find in the current document
3. Tips how to use the basic functions of the device Fujitsu ScanPartner 620C - which should help us in our first steps of using Fujitsu ScanPartner 620C
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fujitsu ScanPartner 620C
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fujitsu ScanPartner 620C in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fujitsu ScanPartner 620C?

Use the form below

If you did not solve your problem by using a manual Fujitsu ScanPartner 620C, ask a question using the form below. If a user had a similar problem with Fujitsu ScanPartner 620C it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)