English dropdown-ico

Manual Spirit Monitor2

19 pages 3.61 mb
Download

Go to site of 19

Summary
  • Spirit Monitor2 - page 1

    Featuring ...

  • Spirit Monitor2 - page 2

    P age 2 SAFETY PRECAUTIONS The SPIRIT MONITOR 2 mixer must only be connected through the P ower Supply supplied. The wires in the mains lead are coloured in accordance with the following code: Earth: Green and Y ellow (Green/Y ellow - US) Neutral: Blue (White - US) Live: Brown (Black - US) As the colours of the wires in the mains lead may not corre ...

  • Spirit Monitor2 - page 3

    P age 3 INPUTS 24 Connecting Up ...

  • Spirit Monitor2 - page 4

    USING MONITOR 2 Mono Input Channel XLR Input The UltraMic Plus padless input preamp is designed to accept BALANCED or UNBALANCED signals at a wide range of input levels up to +28dBu. When using microphones, professional dynamic, condenser or ribbon mics are best because these will be L OW IMPEDANCE. Y ou can use low -cost HIGH IMPEDANCE mics, but t ...

  • Spirit Monitor2 - page 5

    P age 5 MONITOR SENDS These controls route the input channel signal to any one or more Monitor busses and the associated Monitor Outputs, allowing a number of unique monitor mixes to be created. The sends are arranged as a group of mono sends (1-8) and two stereo pairs (9/10 & 11/12). Each group of sends is normally POST -F ADE, POST -EQ but ma ...

  • Spirit Monitor2 - page 6

    P age 6 9 10 8 7 6 1 2 3 4 5 11 OUTPUT SECTION MONITOR OUTPUTS These outputs provide summing of the corresponding input channel monitor sends, and drive XLR -type output sockets from impedance balanced outputs. A break-point is included before each output socket for the connection of an external graphic equaliser . Outputs 1-8 are configured as mon ...

  • Spirit Monitor2 - page 7

    P age 7 MASTER SECTION WEDGE SOURCE The Engineer s W edge outputs are normally fed from a mix of the MNTR feeds from outputs 1-12. The pre-fade wedge signal feeds the headphones and meters and the post-fade signal feeds the XLR outputs. Pressing the WEDGE SOURCE switch selects monitor outputs 11-12 as the source for the wedge outputs, and would ...

  • Spirit Monitor2 - page 8

    P age 8 Setting Up & T roubleshooting Initial Set Up Once you have connected up your system (see the sections on connection and wiring earlier in this manual for guidance) you are ready to set initial positions for the controls on your mixer . The front panel drawing on page 17 shows typical initial control positions which may serve as a useful ...

  • Spirit Monitor2 - page 9

    P age 9 BAND INSTRUMENTS/VOCALS Live Monitor with Effects APPLICA TIONS ...

  • Spirit Monitor2 - page 10

    BAND INSTRUMENTS/VOCALS P age 10 Live Monitor with In-Ear Monitoring ...

  • Spirit Monitor2 - page 11

    P age 11 Theatre ...

  • Spirit Monitor2 - page 12

    P age 12 FOH Console ...

  • Spirit Monitor2 - page 13

    P age 13 FOH Console with Subgrouping ...

  • Spirit Monitor2 - page 14

    P age 14 3 3 3 3 3 1 1 1 1 1 2 2 2 2 2 +48V +48V +48V +48V MIC INPUT SPLIT SPLIT OUTPUT (Internal Link) Link - Grounded No Link - Ground Lift TIP: SEND RING: RETURN HOUSE MICS FX RET 1 LEFT HOUSE FX RET 1 FX RET 2 HOUSE SENS FX RET 2 LEFT FX RET 1 RIGHT FX RET 2 RIGHT LEFT RIGHT T/B MIC T/B SENS PHASE INPUT SENS MONITOR 1 2 3 4 5 6 7 8 9 9-10 PA N ...

  • Spirit Monitor2 - page 15

    Balanced Unbalanced Insert Leads ’Y’ Leads (Unbalanced) Lamp Connections ’Y’ Leads (Balanced) Headphone Splitter P age 15 Connecting Leads ...

  • Spirit Monitor2 - page 16

    Control Position Sheet Y ou may freely copy this page to mark control positions to assist in resetting the desk between performances. ...

  • Spirit Monitor2 - page 17

    P age 17 INPUTS MONITOR 2 CONSOLE T ypical Starting Out Control Positions ...

  • Spirit Monitor2 - page 18

    P age 18 Specifications Noise Measured RMS, 22Hz to 22kHz Bandwidth. Inputs at unity gain and terminated 150 W Output Noise 24 inputs routed, sends down, master @ unity < -80dBu EIN Mic EIN @ max. gain (150 W terminated) -129dBu THD+N Mic sens. -10dBu, Faders @ unity , send at max., +20dBu at all outputs @ 1kHz <0.005% Crosstalk (@1kHz) T ypi ...

  • Spirit Monitor2 - page 19

    A Harman International Company P art No: ZM0192 ...

Manufacturer Spirit Category Music Mixer

Documents that we receive from a manufacturer of a Spirit Monitor2 can be divided into several groups. They are, among others:
- Spirit technical drawings
- Monitor2 manuals
- Spirit product data sheets
- information booklets
- or energy labels Spirit Monitor2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Spirit Monitor2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Spirit Monitor2, service manual, brief instructions and user manuals Spirit Monitor2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Spirit Monitor2.

Similar manuals

A complete manual for the device Spirit Monitor2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Spirit Monitor2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Spirit Monitor2.

A complete Spirit manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Spirit Monitor2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Spirit Monitor2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Spirit Monitor2, that we can find in the current document
3. Tips how to use the basic functions of the device Spirit Monitor2 - which should help us in our first steps of using Spirit Monitor2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Spirit Monitor2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Spirit Monitor2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Spirit Monitor2?

Use the form below

If you did not solve your problem by using a manual Spirit Monitor2, ask a question using the form below. If a user had a similar problem with Spirit Monitor2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)