English dropdown-ico

Manual Russound SP522.1

12 pages 0.24 mb
Download

Go to site of 12

Summary
  • Russound SP522.1 - page 1

    A/V DISTRIBUTION & CONTROL SYSTEMS SP503.1 SP523.1 SP522.1 Instruction Manual ...

  • Russound SP522.1 - page 2

    2 INTRODUCTIONS Congratulations on selecting Russound Ceiling-Mounted Speaker s. Like all RUSSOUND speakers, they combine acoustic technology with dur abil- ity and will provide year s of musical enjoyment. An added feature of model SP503.1 and model SP522.1 is the dual-voice coil design. This is unique in that both left and right signals can funct ...

  • Russound SP522.1 - page 3

    3 OTHER ACOUSTIC CONSIDERA TIONS For best fidelity , there are sever al other factors to keep in mind befor e you start actual installation. Concerns and r eflections: When a ceiling speaker is placed close to the comer of a room, bass fr e- quencies are emphasized. This can be okay if both speaker s are mount- ed near corner (while maintaining ste ...

  • Russound SP522.1 - page 4

    SPEAKER WIRE PATHS In general, you should pay particular attention to the following ar eas: • Avoid running speaker wires close to house electrical wiring for any distance. If you have to run them parallel, make sur e to space the speaker wires at least two feet fr om the AC line. It is, however , okay for speaker wires to cr oss paths with AC li ...

  • Russound SP522.1 - page 5

    7. Tempor arily place a Russound speaker into the cut-out to insure that it fits properly . It’s okay if the hole is slightly off/lar ger by 1/8”, since it will be covered by the speaker’ s outside frame. Actual installation will happen later , after you’ve routed the speaker wires. 8. Repeat steps 1 through 7 for the other speaker . 9. Now ...

  • Russound SP522.1 - page 6

    AT THE SPEAKER END 1. Cut off excess wire, leaving about 2 feet extending thr ough the speaker cut-out hole. 2. Pull the conductors apart so they’r e separated for the fir st two inches from their ends. 3. Using a wire stripper , diagonal pliers or a knife, r emove 1/2 inch of insulation from each conductor . 4. Twist the tiny str ands in each co ...

  • Russound SP522.1 - page 7

    FINAL ASSEMBL Y 1. If you haven’t done so already during painting, r emove the perforat- ed grilles from both Russound Speaker s. Use the clamp (dog-ear) to push the grille out from the back side. 2. Center the speaker in the cut-out hole and tighten the screws until the clamps are dr awn up snugly from behind, clamping the speaker in place. Try ...

  • Russound SP522.1 - page 8

    TAKING CARE OF Y OUR NEW CEILING SPEAKERS RUSSOUND Ceiling Speakers ar e designed to last the life of your home if you follow a few simple rules. The main “killers” of any louds peaker sy stem are: • too little power at high volumes • too much power at high volumes • transients (immediate loud passages, thumps, etc.) Too little power: It? ...

  • Russound SP522.1 - page 9

    INSTALLING DURING NEW CONSTRUCTION Needless to say , installing In-Wall speakers when a house is being built is far easier than doing it later . Russound offers a Speaker Rough-In Brackets for r ound speakers (Model SB-1.5). The br acket is designed to provide the drywall installer s the cut-out for the In-Walls. Each kit comes with two brackets, ( ...

  • Russound SP522.1 - page 10

    TECHNICAL SPECIFICATIONS SP503.1 Frequency Response: 68Hz - 18kHz Construction: Dual Voice Coil, Dual Drive 5.25" P olymica cone with coni- cal high frequency driver . Moisture r esistant Sensitivity: 88dB Min / Max P ower: 1 0 to 60 W/Channel Impedance: 4 Ohm, 8 Ohm, 16 Ohm (depending on wiring) Frame: ABS plastic, paintable Grille: Fine mesh ...

  • Russound SP522.1 - page 11

    NOTES 11 ...

  • Russound SP522.1 - page 12

    A/V DISTRIBUTION & CONTROL SYSTEMS 5 Forbes Rd. Newmarket, NH 03857, USA ☎ 603.659.5 170 • F ax 603.659.5388 e-mail: tech@russound.com Fax-On-Demand: 603.659.5590 Come visit u s at: ...

Manufacturer Russound Category Speaker

Documents that we receive from a manufacturer of a Russound SP522.1 can be divided into several groups. They are, among others:
- Russound technical drawings
- SP522.1 manuals
- Russound product data sheets
- information booklets
- or energy labels Russound SP522.1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Russound SP522.1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Russound SP522.1, service manual, brief instructions and user manuals Russound SP522.1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Russound SP522.1.

Similar manuals

A complete manual for the device Russound SP522.1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Russound SP522.1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Russound SP522.1.

A complete Russound manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Russound SP522.1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Russound SP522.1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Russound SP522.1, that we can find in the current document
3. Tips how to use the basic functions of the device Russound SP522.1 - which should help us in our first steps of using Russound SP522.1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Russound SP522.1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Russound SP522.1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Russound SP522.1?

Use the form below

If you did not solve your problem by using a manual Russound SP522.1, ask a question using the form below. If a user had a similar problem with Russound SP522.1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)