-
Invacare Pronto M51 Base - page 1
Owner’s Operator and Maintenance Manual DEALER: This manual MUST be given to the user of the product. USER: B E F OR E u s i n g t h i s product, read this manual and save for future reference. For more information regarding Invacare products, parts, and services, please visit www.invacare.com Pronto ® M51 ™ Base with SureStep ® Formula ™ C ...
-
Invacare Pronto M51 Base - page 2
REFERENCE DOCUMENTS Pronto ® M51 ™ Base with SureS tep ® 2 Part No. 114807 6 WARNING A QUALIFIED TECHNICIAN MUST PERFORM THE INITIAL SET UP OF THIS WHEELCHAIR. ALSO, A QUALIFIED TECHNICIAN MUST PERFORM ALL PROCEDURES IN THE SERVICE MANUAL. WHEELCHAIR USERS: DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING (1) ...
-
Invacare Pronto M51 Base - page 3
TABLE OF CONTENTS Part No. 1148076 3 Pronto ® M51 ™ Base with SureStep ® TABLE OF CONTENTS REFERENCE DOCUMENTS ................................................................. 2 REGISTER YOUR PR ODUCT ............................................................... 4 SPECIAL NOTES ................................................................ ...
-
Invacare Pronto M51 Base - page 4
TABLE OF CONTENTS Pronto ® M51 ™ Base with SureS tep ® 4 Part No. 114807 6 TABLE OF CONTENTS SECTION 8—TOP SHROUD AND WHEELS ......................................... 47 Replacing the Flat Free Tires on the Wheel Rim ....................... ............................................. ..........47 Removing/Installing the Batt ery Shroud .... ...
-
Invacare Pronto M51 Base - page 5
SPECIAL NOTES Part No. 1148076 5 Pronto ® M51 ™ Base with SureStep ® SPECIAL NOTES Signal words are use d in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage. Refer to the table ...
-
Invacare Pronto M51 Base - page 6
SPECIAL NOTES Pronto ® M51 ™ Base with SureS tep ® 6 Part No. 114807 6 TRRO AND TRBKTS WARNINGS Only use the transport brackets included with TRRO and TRBK TS for the purposes described in this manual. WARNING ALWAYS wear your seat po sitioning strap. The seat positioning strap is a positioning belt only. It is not designed for use as a ...
-
Invacare Pronto M51 Base - page 7
TYPICAL PRODUCT PARAMETERS Part No. 1148076 7 Pronto ® M51 ™ Base with SureStep ® TYPICAL PRODUCT PARAMETERS *NOTE: Includes seating systems and accessories. **NOTE: Va l u e s for range are calculated for maximum chair weight rating us ing lar gest batteries applicable ...
-
Invacare Pronto M51 Base - page 8
LABEL LOCATION Pronto ® M51 ™ Base with SureS tep ® 8 Part No. 114807 6 LABEL LOCATION ...
-
Invacare Pronto M51 Base - page 9
LABEL LOCATION Part No. 1148076 9 Pronto ® M51 ™ Base with SureStep ® Wheelchairs With TRRO Wheelchairs Without TRRO NOTE: Also on opposite side. NOTE: Also on opposite side. NOTE: Also on opposite side. NOTE: Auto style seat positioning strap shown. This label ...
-
Invacare Pronto M51 Base - page 10
SECTION 1—GENERAL GUIDELINES Pronto ® M51 ™ Base with SureS tep ® 10 Part No. 114807 6 SECTION 1—GENERAL GUIDELINES WARNING SECTION 1 - GENERAL GUIDELIN ES contai ns important inform ation for the safe operation and use of this product. DO NOT use this prod uct or any available optional equipment without first comple tely reading and un ...
-
Invacare Pronto M51 Base - page 11
SECTION 1—GENERAL GUIDELINES Part No. 1148076 11 Pronto ® M51 ™ Base with SureStep ® DO NOT climb, go up or down ramps or trav erse slopes greater than 9°. DO NOT attempt to move up or down an incline with a wa t e r, ice or oil ? ...
-
Invacare Pronto M51 Base - page 12
SECTION 1—GENERAL GUIDELINES Pronto ® M51 ™ Base with SureS tep ® 12 Part No. 114807 6 Batteries The warranty and performance specifications contained in this manual are based on the use of deep cycle gel cell or sealed lead acid batteries. Inv aca ...
-
Invacare Pronto M51 Base - page 13
SECTION 1—GENERAL GUIDELINES Part No. 1148076 13 Pronto ® M51 ™ Base with SureStep ® Grounding Instructions DO NOT , under any circumstances, cut or remov e the round grounding prong from any plug used with or for Inv acare products. Some de vices are ...
-
Invacare Pronto M51 Base - page 14
SECTION 2—EMI INFORMATION Pronto ® M51 ™ Base with SureS tep ® 14 Part No. 114807 6 SECTION 2—EMI INFORMATION WARNING CAUTION: IT IS VERY IMPORTANT THAT YOU READ THIS INF ORMATION REGARDING THE POSSIBLE E FFECTS OF ELECTROMAGNETIC INTERFERENCE ON YOUR POWERED WHEELCHAIR. Electromagnetic Interference (E MI) From Radio Wave Sources Powere ...
-
Invacare Pronto M51 Base - page 15
SECTION 2—EMI INFORMATION Part No. 1148076 15 Pronto ® M51 ™ Base with SureStep ® WARNING Powered Wheelchair Electrom agnetic Interference (EMI) Because EM energy rapidly becomes more intense as one moves closer to the transmitting antenna (source), the EM fi elds from hand-hel d radio wave sources (transceivers) are of special concern. I ...
-
Invacare Pronto M51 Base - page 16
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS Pronto ® M51 ™ Base with SureS tep ® 16 Part No. 114807 6 SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS “Safety and Handling” of the wheelchair requires the close atte ntion of the wheelchair user as wel l as the assistant. Th ...
-
Invacare Pronto M51 Base - page 17
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1148076 17 Pronto ® M51 ™ Base with SureStep ® Coping With Everyday Obstacles WARNING DO NOT attempt to reach object s if you have to move fo rward in the seat or pick them up from the floor by reac hing down between your knees. Proper positioning is essent ial for your safety. When re ach ...
-
Invacare Pronto M51 Base - page 18
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS Pronto ® M51 ™ Base with SureS tep ® 18 Part No. 114807 6 A Note to Wheelchair Assistants When assistance to the wheelchair user is required, remember to use good body mechanics. Keep you r back straight and be nd you r ...
-
Invacare Pronto M51 Base - page 19
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1148076 19 Pronto ® M51 ™ Base with SureStep ® NOTE: When using a stairway to move the wheelchair , seat and any accessories, move all wheelchair components away fr om the stairway prior to r eassembly ...
-
Invacare Pronto M51 Base - page 20
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS Pronto ® M51 ™ Base with SureS tep ® 20 Part No. 114807 6 Transferring To and From Other Seats WARNING ALWAYS turn the wheelchair power Off and engage the Motor Release Levers to prevent the wheels from moving before attempting to tr ansfer in or out of the wheelchair. Also, make sure every precau ...
-
Invacare Pronto M51 Base - page 21
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1148076 21 Pronto ® M51 ™ Base with SureStep ® Reaching, Leanin g and Bending - Forward NOTE: For this proced ure, ref er to FIGURE 3.4. Po s i t i o n the front and re ar casters so that they are extended as far f ...
-
Invacare Pronto M51 Base - page 22
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING Pronto ® M51 ™ Base with SureS tep ® 22 Part No. 114807 6 SECTION 4—SAFETY INSPECTION/ TROUBLESHOOTING NOTE: Every six months or as necessary take your wheelchai r to a qualified dealer for a thor ough inspection and servi ...
-
Invacare Pronto M51 Base - page 23
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1148076 23 Pronto ® M51 ™ Base with SureStep ® Inspect/Adjust Weekly ❑ Seat is secured to wheelchair frame. ❑ Inspect tires for flat spots and w ear . ❑ Ensure casters are free of debris. Inspect/Adjust Monthly ❑ Ensure ...
-
Invacare Pronto M51 Base - page 24
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING Pronto ® M51 ™ Base with SureS tep ® 24 Part No. 114807 6 All Wheelchairs General Troubleshooting SYMPTOM PROBABLE CAUSE SOLUTIONS Limited driving distance. Batteries not charged long enough. Batteries we ak; wont hold charge. Charge batteries overnight or ensure 8 hours of charge time between use. ...
-
Invacare Pronto M51 Base - page 25
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1148076 25 Pronto ® M51 ™ Base with SureStep ® SPJ™+ w/PSS or SPJ+ w/ACC Joysticks The joystick information gauge and the service indicator give indicat ions of the type of fault or error detected by the contr ...
-
Invacare Pronto M51 Base - page 26
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING Pronto ® M51 ™ Base with SureS tep ® 26 Part No. 114807 6 Service Indicator Light Diagnostics MPJ™+, PSR+, PSF+ Joysticks or Displays NUMBER OF FLASHES ERROR CODE DESCRIPTION POSSIBLE SOLUTION 1 User Fault Release joystick to n eutral and try again. 2 Battery Fault Charge the batterie s. Refer to ...
-
Invacare Pronto M51 Base - page 27
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1148076 27 Pronto ® M51 ™ Base with SureStep ® NEUTRAL TESTING displays. The joystick neutral test has failed (Error code E18). Release the joystick and try to get the joystick back into the center-most position. BAD JOYSTICK CAL VALUES displays and the wheelchair does not drive. The jo ...
-
Invacare Pronto M51 Base - page 28
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING Pronto ® M51 ™ Base with SureS tep ® 28 Part No. 114807 6 Checking Battery Charge Level The following “Do’ s” and “Don’ts” are provided for your convenience an d safety . DON’T DO Don’t perform any instal lation or maintenance without first ...
-
Invacare Pronto M51 Base - page 29
SECTION 5—WHEELCHAIR OPERATION Part No. 1148076 29 Pronto ® M51 ™ Base with SureStep ® SECTION 5—WHEELCHAIR OPERATION WARNING After ANY adjustments, repa ir or service and before use, make sure that all attaching hardware is tightene d securely - otherwise inju ry or damage may result. Set-up of the Electron ic Control Unit is to be per ...
-
Invacare Pronto M51 Base - page 30
SECTION 5—WHEELCHAIR OPERATION Pronto ® M51 ™ Base with SureS tep ® 30 Part No. 114807 6 Using the Joystick to Drive the Wheelchair NOTE: For this proced ure, ref er to FIGURE 5.2. The joystick is located on the joystick housing and provides smooth control of speed ? ...
-
Invacare Pronto M51 Base - page 31
SECTION 5—WHEELCHAIR OPERATION Part No. 1148076 31 Pronto ® M51 ™ Base with SureStep ® MK6i™ SPJ+ w/PSS and MK6i SPJ+ w/ACC Joystick Switches and Indicators NOTE: For this proced ure, ref er to FIGURE 5.3. FIGURE 5.3 MK6i™ SPJ+ w/PSS and MK6i SPJ+ w/AC C Joystick Switches and Indicators On/Off Button This butto ...
-
Invacare Pronto M51 Base - page 32
SECTION 5—WHEELCHAIR OPERATION Pronto ® M51 ™ Base with SureS tep ® 32 Part No. 114807 6 Speed Control Buttons The speed control buttons (tortoise button () and hare button () ) are used to set and adjust the maximum speed. 1. T o adjust the speed, per ...
-
Invacare Pronto M51 Base - page 33
SECTION 5—WHEELCHAIR OPERATION Part No. 1148076 33 Pronto ® M51 ™ Base with SureStep ® Information Gauge Display The information gauge display is located on the front of the joystick housing and provides the following information to the user on the sta ...
-
Invacare Pronto M51 Base - page 34
SECTION 5—WHEELCHAIR OPERATION Pronto ® M51 ™ Base with SureS tep ® 34 Part No. 114807 6 FIGURE 5.4 MPJ+ Joystick Switches and Indicators Speed Control The speed control knob is located on the side of the joystick housing. 1. Rotate the knob clockwise (forw ard) to in ...
-
Invacare Pronto M51 Base - page 35
SECTION 5—WHEELCHAIR OPERATION Part No. 1148076 35 Pronto ® M51 ™ Base with SureStep ® Splash Screen NOTE: For this proced ure, ref er to FIGURE 5.5. This screen is displayed at startup of the joystick for about 2 seconds. This screen displays the s ...
-
Invacare Pronto M51 Base - page 36
SECTION 5—WHEELCHAIR OPERATION Pronto ® M51 ™ Base with SureS tep ® 36 Part No. 114807 6 FIGURE 5.6 LCD Display Screens - Main Screen Driving Screen NOTE: For this proced ure, ref er to FIGURE 5.7. This screen is shown when the operator issues a drive command and the ...
-
Invacare Pronto M51 Base - page 37
SECTION 5—WHEELCHAIR OPERATION Part No. 1148076 37 Pronto ® M51 ™ Base with SureStep ® Connected Devices Screen NOTE: For this proced ure, ref er to FIGURE 5.8. This screen is displayed if the Mode Select switch is held active for about 10 seconds. This ? ...
-
Invacare Pronto M51 Base - page 38
SECTION 5—WHEELCHAIR OPERATION Pronto ® M51 ™ Base with SureS tep ® 38 Part No. 114807 6 Remote On/Off Switch The remote On/Off switch input is locate d at the rear of the joystick on the right side and allows the power switch to be operated by ...
-
Invacare Pronto M51 Base - page 39
SECTION 5—WHEELCHAIR OPERATION Part No. 1148076 39 Pronto ® M51 ™ Base with SureStep ® Repositioning Joystick NOTE: For this proced ure, ref er to FIGURE 5.9. 1. T urn the adjustment lo ck lev er to release the joystick mounting tube from the mounting bracket. 2. ...
-
Invacare Pronto M51 Base - page 40
SECTION 5—WHEELCHAIR OPERATION Pronto ® M51 ™ Base with SureS tep ® 40 Part No. 114807 6 Disconnecting/Connecting the Joysticks NOTE: For this proced ure, ref er to FIGURE 5.10 on page 40. NOTE: The joystick connector is loca ted at the rea r of the seat frame. SP ...
-
Invacare Pronto M51 Base - page 41
SECTION 6—SEAT Part No. 1148076 41 Pronto ® M51 ™ Base with SureStep ® SECTION 6—SEAT WARNING After ANY adjustments, repa ir or service and BEF ORE use, make sure that all attaching hardware is tightene d securely - otherwise inju ry or damage may result. Before performing any maintenance, ad justment or service , verify that ON/OFF swi ...
-
Invacare Pronto M51 Base - page 42
SECTION 6—SEAT Pronto ® M51 ™ Base with SureS tep ® 42 Part No. 114807 6 9. Gently allow we ig h t of seat assembly to be supported by the prop rod. NOTE: Only leave the seat assemb ly in the Up/Open position while performing any necessary ...
-
Invacare Pronto M51 Base - page 43
SECTION 6—SEAT Part No. 1148076 43 Pronto ® M51 ™ Base with SureStep ® Removing/Installing the Seat Assembly NOTE: For this proced ure, ref er to FIGURE 6.2. NOTE: This procedur e is for wheelchairs WITHOUT the Formula PT O Pl us seating system installed ONLY . ? ...
-
Invacare Pronto M51 Base - page 44
SECTION 7—FOOTBOARD ASSEMBLY Pronto ® M51 ™ Base with SureS tep ® 44 Part No. 114807 6 SECTION 7—FOOTBOARD ASSEMBLY WARNING After any adjustments, repair or service and before us e, make sure th at all attaching hardware is tightened securely - othe rwise injury or damage may result. Before performing any maintenance, adju stment or ser ...
-
Invacare Pronto M51 Base - page 45
SECTION 7—FOOTBOARD ASSEMBLY Part No. 1148076 45 Pronto ® M51 ™ Base with SureStep ® Installing WARNING Make sure the detent balls of the quick- release pin are full y released beyond the outer edge of the tube befo re operating the wh eelchair. Otherwise, injury and /or damage may result. Keep detent balls clean. 1. P osition the ...
-
Invacare Pronto M51 Base - page 46
SECTION 7—FOOTBOARD ASSEMBLY Pronto ® M51 ™ Base with SureS tep ® 46 Part No. 114807 6 FIGURE 7.2 Adjusting the Footboard Assembly - Angle Depth NOTE: For this proced ure, ref er to FIGURE 7.3. 1. Remove the quick release pin that secures the footboard assembly to the whe ...
-
Invacare Pronto M51 Base - page 47
SECTION 8—TOP SHROUD AND WHEELS Part No. 1148076 47 Pronto ® M51 ™ Base with SureStep ® SECTION 8—TOP SHROUD AND WHEELS WARNING After any adjustments, repair or service and before us e, make sure th at all attaching hardware is tightened securely - othe rwise injury or damage may result. Before performing any maintenance, adju stment or ...
-
Invacare Pronto M51 Base - page 48
SECTION 8—TOP SHROUD AND WHEELS Pronto ® M51 ™ Base with SureS tep ® 48 Part No. 114807 6 Installing 1. Ensure the seat is tilted back to the up position or removed. Refer to Tilting the Seat Assembly (Formula CG Only) on page 41 or Refer to ? ...
-
Invacare Pronto M51 Base - page 49
SECTION 8—TOP SHROUD AND WHEELS Part No. 1148076 49 Pronto ® M51 ™ Base with SureStep ® Engaging/Disengaging Motor Release Lever WARNING DO NOT engage or disengage the motor releas e lever until the On/Off switch on the joystick is in the Off position. CAUTION Ensure both motor re lease levers ar e fully engaged before driving the wheelch ...
-
Invacare Pronto M51 Base - page 50
SECTION 8—TOP SHROUD AND WHEELS Pronto ® M51 ™ Base with SureS tep ® 50 Part No. 114807 6 Replacing Front/Rear Caster Assemblies NOTE: For this proced ure, ref er to FIGURE 8.3. NOTE: Front and rear caster assemblies are rep l a ce d in the same manner . NOTE: When re ...
-
Invacare Pronto M51 Base - page 51
SECTION 9—BATTERIES Part No. 1148076 51 Pronto ® M51 ™ Base with SureStep ® SECTION 9—BATTERIES Warnings For Handling and Replacing Batteries WARNING After any adjustments, repair or service and before us e, make sure th at all attaching hardware is tightened securely - othe rwise injury or damage may result. Make sure power to the whee ...
-
Invacare Pronto M51 Base - page 52
SECTION 9—BATTERIES Pronto ® M51 ™ Base with SureS tep ® 52 Part No. 114807 6 Using the Proper Batteries NOTE: For this proced ure, ref er to FIGURE 9.1. 1. Place battery on ground/flat surface. 2. V isually draw a horizontal and vertical centerline through the middle ...
-
Invacare Pronto M51 Base - page 53
SECTION 9—BATTERIES Part No. 1148076 53 Pronto ® M51 ™ Base with SureStep ® Removing/Installing Batteri es from/into Battery Tray WARNING ALWAYS use the battery handle when lifting the battery. It is the most convenient method and assures that the b attery acid will not spill. It also help s to prolong the life of the battery. DO NOT tip ...
-
Invacare Pronto M51 Base - page 54
SECTION 9—BATTERIES Pronto ® M51 ™ Base with SureS tep ® 54 Part No. 114807 6 2. P osition the front battery in the front of the battery tray . 3. P osition rear battery in rear of battery tray . NOTE: Ensure that bo th batteries ar e pr operly sea ...
-
Invacare Pronto M51 Base - page 55
SECTION 9—BATTERIES Part No. 1148076 55 Pronto ® M51 ™ Base with SureStep ® Connecting/Disconnecting Battery Cables Connecting Battery Cables WARNING NEVER allow any of your tools and/or b attery cables to co ntact both battery terminals at the same time . An electrical short may occur and serious personal injury or damage may occur. Conn ...
-
Invacare Pronto M51 Base - page 56
SECTION 9—BATTERIES Pronto ® M51 ™ Base with SureS tep ® 56 Part No. 114807 6 NOTE: New batteries MUST be fully char ged befor e using, otherwise the life of the bat teries will be reduced. 6. If necessary , charge the bat tery . Refer to Charging ...
-
Invacare Pronto M51 Base - page 57
SECTION 9—BATTERIES Part No. 1148076 57 Pronto ® M51 ™ Base with SureStep ® Disconnecting Battery Cables WARNING The use of rubber gloves is recommended when working with batteries. NEVER allow any of your tools and/or b attery cables to co ntact both battery terminals at the same time . An electrical short may occur and serious personal ...
-
Invacare Pronto M51 Base - page 58
SECTION 9—BATTERIES Pronto ® M51 ™ Base with SureS tep ® 58 Part No. 114807 6 MPJ+ Joystick NOTE: For this proced ure, ref er to FIGURE 9.5. The far right side of the display screen is the Battery Gauge Display (BGD). It provides information on the ...
-
Invacare Pronto M51 Base - page 59
SECTION 9—BATTERIES Part No. 1148076 59 Pronto ® M51 ™ Base with SureStep ® The amount of electrical current drawn within a given time to charge a battery is called “charge rate”. If, due to usage, the charge stored in the battery ? ...
-
Invacare Pronto M51 Base - page 60
SECTION 9—BATTERIES Pronto ® M51 ™ Base with SureS tep ® 60 Part No. 114807 6 1. Plug the female connector of the AC pow er cord (supplied) to the AC receptacle on the cha rger and plug in the male connector on the AC pow er co rd i ...
-
Invacare Pronto M51 Base - page 61
SECTION 9—BATTERIES Part No. 1148076 61 Pronto ® M51 ™ Base with SureStep ® Charging Using An Independent Ch arger Plugged Into The Joystick WARNING Read and carefully fol low the individual in structions for each charger (supplied or purchased). If charging instructions are no t supplied, consult a qualif ied technician for proper proced ...
-
Invacare Pronto M51 Base - page 62
SECTION 10—TRANSPORT READY PACKAGE Pronto ® M51 ™ Base with SureS tep ® 62 Part No. 114807 6 SECTION 10—TRANSPORT READY PACKAGE NOTE: The info rmation in this section is for wheelchairs ordered with the transport re a d y package ONLY . WARNING Contact Invacare Corporation (800 ...
-
Invacare Pronto M51 Base - page 63
SECTION 10—TRANSPORT READY PACKAGE Part No. 1148076 63 Pronto ® M51 ™ Base with SureStep ® WARNING Only use the transport brackets included with TRRO and TRBK TS for the purposes described in this manual. About Transport Ready Packages TRRO includes four factory ‐ installed transport brackets and a wheelc ...
-
Invacare Pronto M51 Base - page 64
SECTION 10—TRANSPORT READY PACKAGE Pronto ® M51 ™ Base with SureS tep ® 64 Part No. 114807 6 Securing the Wheelchair to the Vehicle Positioning the Wheelchair in the Vehicle WARNING This wheelchair must be in a forward facing positi on during travel in a motor vehicle. The recommended clear zones for wheelch air seated occupants restraine ...
-
Invacare Pronto M51 Base - page 65
SECTION 10—TRANSPORT READY PACKAGE Part No. 1148076 65 Pronto ® M51 ™ Base with SureStep ® Securement Points FIGURE 10.1 Securement Points Securing the Wheelchair This wheelchai r is to be used only with Wheelchair Tie ‐ down and Occupant Restraint Systems (WTORS) that have ...
-
Invacare Pronto M51 Base - page 66
SECTION 10—TRANSPORT READY PACKAGE Pronto ® M51 ™ Base with SureS tep ® 66 Part No. 114807 6 Securing the Occupant Wheelchair-Anchored Belts WARNING The pelvic belt that is provid ed by Invacare has been test ed for use in a motor vehi- cle on this wheelchair ONLY. DO NOT replac e the pelvic belt wi th a different style pelvic belt. NOTE: ...
-
Invacare Pronto M51 Base - page 67
SECTION 10—TRANSPORT READY PACKAGE Part No. 1148076 67 Pronto ® M51 ™ Base with SureStep ® Vehicle-Anchored Belts NOTE: For this proced ure, ref er to FIGURE 10.3. This wheelchai r has an ov erall rating of “A ” with regard to accommodating the use and fit ...
-
Invacare Pronto M51 Base - page 68
SECTION 10—TRANSPORT READY PACKAGE Pronto ® M51 ™ Base with SureS tep ® 68 Part No. 114807 6 Positioning Belts WARNING The angle of the pelv ic belt should be within the prefe rred zone of 45 to 75 degrees to the horizo ntal OR within the optional zone of 30 to 45 degrees to the horizontal. Steeper side-view pelvic belt angle s are especi ...
-
Invacare Pronto M51 Base - page 69
NOTES Part No. 1148076 69 Pronto ® M51 ™ Base with SureStep ® NOTES ...
-
Invacare Pronto M51 Base - page 70
NOTES Pronto ® M51 ™ Base with SureS tep ® 70 Part No. 114807 6 NOTES ...
-
Invacare Pronto M51 Base - page 71
NOTES Part No. 1148076 71 Pronto ® M51 ™ Base with SureStep ® NOTES ...
-
Invacare Pronto M51 Base - page 72
LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty i s extended only to the origin al purchaser wh o purchases th is product whe n new and unus ed from Invacare or a deal er. This warranty is not extended to any other person or entity and ...
Do you have a question concerning Invacare Pronto M51 Base?
Use the form below
If you did not solve your problem by using a manual Invacare Pronto M51 Base, ask a question using the form below. If a user had a similar problem with Invacare Pronto M51 Base it is likely that he will want to share the way to solve it.